Halsey Taylor 2205 User manual

96893C (Rev. B - 2/00)PAGE 1
Halsey Taylor Installation Manual
Model 2205 Fountain
To assure you install this model easily and correctly,
PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE
INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH
PLUMBING, ELECTRICALAND OTHER APPLICABLE CODES. After installation, leave these
instructions inside the fountain for future reference.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
Installer

96893C (Rev. B - 2/00) PAGE 2
SIDE VIEW
FRONT VIEW

96893C (Rev. B - 2/00)PAGE 3
ASSEMBLY
1. Assemble support brackets to the fountain by aligning holes in bracket with holes in cooler and fastening with
(4) #10 screws provided.
2. Slide drain tube into drain fitting and secure by sliding drain nut over drain tube and tightening nut to
drain fitting.
3. Attach bubbler to fountain by inserting bubbler nipple through the hole in the cooler top and securing
with the washer and nut provided.
INSTALLATION
1. This fountain is to be mounted on a smooth, flat, finished wall surface, with adequate support structure.
2. Establish rim height fountain is to be mounted.
3. Refer to rough-in for plumbing.
4. Locate and install trap. (Trap not included).
5. Install shut-off valve on building water supply. (Shut off valve not furnished).
6. Locate and install hanger bracket using 1/4" (10mm) lag screws or bolts. (Not included).
7. Install and center fountain on hanger bracket by slipping the back edge of the cooler top over the
flange on the hanger bracket. Secure fountain using 1/4" (10mm) minimum lag screws or bolts (Not
included).
CAUTION: This fountain is rated for inlet water pressure of 20-90 psi. Should the inlet water supply exceed
90 psi, a pressure reducing regulator should be used.
8. Connect fountain to building supply line by running a 3/8" (10mm) water line between the shut-off
valve and fountain.
9. Turn "ON" water supply and check all connections for leaks.
10. Adjust bubbler stream height. (See instructions below).
TROUBLE SHOOTING AND MAINTENANCE
Orifice Assy: Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposits may be
removed from the orifice with a small round file not over 1/8" diameter or small diameter wire.
CAUTION: DO NOT file or cut orifice material.
Stream Regulator: If orifice is clean, regulate flow as stated below. If replacement is necessary, see parts list for
correct regulator part number.
STREAM HEIGHT ADJUSTMENT: Stream height is factory set
at 45-50 PSI. If supply pressure varies greatly from this, remove
items 16, and 17 (See figure 2) from bubbler assembly and
adjust the screw on the regulator (Item 20). Clockwise adjust-
ment will raise stream height and counterclockwise will lower
the stream height. A stream height of 1-1/2" (38mm) is recom-
mended.
FIG. 1

96893C (Rev. B - 2/00) PAGE 4
ITEMIZED PARTS LIST
ITEM NO. PARTNO. DESCRIPTION
100687608640
101486340560
112627543890
171484242830
27234C
27235C
27238C
40294C
55914C
75498C
75588C
75589C
LK142
10031C
100322740560
40048C
40089C
40322C
45675C
61313C
70012C
72460042
A54800
A54888
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Plug Button
Drain Gasket
Screw - #10-24 x .50 PHTC
Basin
Bracket - Support LH
Bracket - Support RH
Bracket - Wall Hanger
Tailpipe - 1-1/4 O.D. x 4.00 IN.
Adapter - Drain
Screw - #8 x .63 FHTC
Nut - Slip Joint 1-1/4
Washer - Seal
Bubbler Assembly
Retaining Nut 1 1/8-24
Gasket
Button
Cover Nut 1 1/8-24
Orifice Assembly
Bubbler Body
Regulator
Lock Nut 3/8-18
Metal Washer
Nipple
Screen
PRINTED IN U.S.A.
2222 CAMDEN COURT
OAK BROOK, IL 60523
13
18
19
5
410
1
16
20
17
22
23
24
15
21
See Fig. 2 7
6
3
12
11
8
9
2
14
FIG. 2
FIG. 3