Halsey Taylor HBW8AQ 1L Series User manual

98072C (10/04)
HBW8AQ*1L, 2L HBW13AQ*1L, 2L HBW*H-L-R
PAGE 1
HALSEY TAYLOR OWNERS MANUAL
USES HFC-134A REFRIGERANT
FIG. 1
SEE FIG. 4
SEE FIG.3
21
18
35
16
17
23
22
6
8,9
33
10
3,4,5
7
11
12
32
34
2
19
1
13,14,15 20
36
37,38,39
30
31
42
40
41
SEE
DETAIL
ABOVE
43
NOTE: Non-refrigerated units do not include all electrical and refrigeration components shown above.
Other components and rough-in are the same as shown.

98072C (10/04)
HBW8AQ*1L, 2L HBW13AQ*1L, 2L HBW*H-L-R
PAGE 2
FIG. 2
* RECOMMENDED HEIGHT FOR ADULTS.
DECREASE HEIGHT FOR CHILDREN.
* ALTURA RECOMENDADA PARA ADULTOS. REDUZCA
PARA LOS NIÑOS.
* HAUTEUR RECOMMANDÉE POUR LES ADULTES.
INSTALLEZ PLUS BAS POUR LES ENFANTS.
FINISHED FLOOR
PISO ACABADO
PLANCHER FINI
LEGEND/LEYENDA/LÉGENDE
A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2 IN. (38 mm) OUT FROM WALL SHUT OFF BY
OTHERS
SE RECOMIENDA UBICAR EL TUBO CORTO DE CONEXIÓNALTUBO DE COBRE SIN CHAPAR DE 3/8" DE DIÁM. EXT.A1-1/2" (38 mm) FUERA DE LALLAVE DE
PASO EN LAPARED COLOCADA POR TERCEROS.
EMPLACEMENT RECOMMANDÉ D'ALIMENTATION EN EAU PAR TUBE EN CUIVRE NON PLAQUÉ DE 3/8 PO. (9,5 mm) D.E. CONNECTANT UNE TUYAUTERIE DE
1-1/2 PO. (38 mm) DEPUIS LE ROBINET D'ARRÊT FOURNI PAR D'AUTRES.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4 O.D. DRAIN
UBICACIÓN RECOMENDADA PARA EL DRENAJE DE SALIDADE AGUA, DE 1¼ DE DIÁMETRO.
EMPLACEMENT RECOMMANDÉ POUR LE DRAIN DE D.E. 1-1/4" DE SORTIE DEAU.
C = 1-1/4 TRAP NOT FURNISHED**
PURGADOR DE 1¼ NO PROPORCIONADO**
SIPHON 1-1/4 NON FOURNI**
D = ELECTRICAL OUTLET LOCATION
UBICACIÓN DE LA TOMA DE ELECTRICIDAD
EMPLACEMENT DE LA PRISE DE COURANT
E = INSURE PROPER VENTILATION BY MAINTAINING 4" (102mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
ASEGURE UNA VENTILACIÓNADECUADA MANTENIENDO UN ESPACIO E 4" (102mm) (MÍN.) DE HOLGURA ENTRE LAREJILLA DE VENTILACIÓN DEL MUEBLE Y
LA PARED
ASSUREZ-VOUS UNE BONNE VENTILATION EN GARDANT 4" (102mm) (MIN.) ENTRE LES ÉVENTS DE LENCEINTE ET LE MUR.
F = POWER CORD 1-1/2FEET (457mm) LONG
CABLE ELÉCTRICO DE 1½ PIE, 457 mm DE LARGO
CORDON DALIMENTATION 1-1/2' (457mm)
G = 5/16" (8mm) SCREW HOLES IN MOUNTING PLATE
AGUJEROS DE TORNILLO 5/16" (8mm) EN LAPLACA DE MONTAJE
TROUS DE VIS 5/16" (8mm) DANS LA PLAQUE DE MONTAGE

98072C (10/04)
HBW8AQ*1L, 2L HBW13AQ*1L, 2L HBW*H-L-R
PAGE 3
FIG. 3
Stream height is factory set at 35 PSI. If supply pressure varies greatly from this,
remove items 24 and 25 and adjust screw on item 27. Clockwise adjustment will raise stream
and counter-clockwise adjustment will lower stream. For best adjustment, stream should hit
basin approximately 6-1/2" (165mm) from bubbler.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
HANGER BRACKETS & TRAP INSTALLATION
1) Remove hanger brackets fastened to back of cooler by removing screws.
2) Mount the hanger brackets and trap as shown in Figure 2.
NOTE: Hanger Brackets and trap MUST be supported securely. Add fixture support carrier if wall will not provide adequate
support.
IMPORTANT:
- 5-1/2 in. (140mm) dimension from wall to centerline of trap must be maintained for proper fit.
- Anchor hanger securely to wall using all mounting holes.
3) Install straight valve for 3/8" O.D. unplated copper tube.
INSTALLATION OF COOLER
4) Hang the cooler on the hanger brackets. Be certain the hanger brackets are engaged properly in the frame and wrapper.
5) Remove the access panel on the underside of the cooler and set it aside.
6) Connect water inlet line--See Note 4 of General Instructions.
7) Remove the slip nut and gasket from the trap and install them on the cooler waste line making sure that the end of the waste
line fits into the trap. Assemble the slip nut and gasket to the trap and tighten securely.
START UP
Also See General Instructions
8) Replace the front panel and secure by retightening all screws.
CORRECT STREAM HEIGHT
FIG. 4
WRAPPER
27
25
26
24 28 29

98072C (10/04)
HBW8AQ*1L, 2L HBW13AQ*1L, 2L HBW*H-L-R
PAGE 4
ITEMIZED PARTS LIST
ITEM NO. PARTNO. DESCRIPTION
36208C
27095C
30664C
70018C
31490C
70009C
56237C
51544C
56159C
66743C
66703C
36094C
36158C
35768C
35959C
66576C
40041C
40429C
26664C
70208C
31513C
66534C
55996C
27239C
40089C
40048C
15005C
61313C
40169C
50986C
40038C
40619C
27093C
27292C
27097C
27094C
See Color Table
50144C
70184C
70418C
40043C
50105C
50074C
70817C
56092C
Power Cord
Fan Bracket
Fan Blade
Hex Nut - Fan Blade
Fan Motor
Screw (Fan Motor)
Shroud - Fan
Bubbler
Nipple - Bubbler
Condenser
Drier
Compressor Serv. Pak EMI 70 HNR
Overload
Cover - Relay
Relay
Heat Exchanger
Tailpipe Assy (8 Gal)
Precooler Assy (13 Gal)
Basin - Stainless Steel
Screw - Basin Mtg.
Cold Control
Evaporator Assembly
Strainer
Bracket - Precooler
Cover
Button
Retaining Nut
Regulator
Hex Nut
Regulator Holder
Strainer - Beehive
Ferrule - Tailpipe
Angle - Front Corners
Bracket - Basin Mounting
Frame - Back/Bottom
Bracket - Front
Wrapper
Grommet - Compressor Mtg
Hair Pin - Cotter
Washer
Locknut
Tailpipe Gasket
Tailpipe Gasket
Fitting - Elbow 1/4 Stem
Poly Tubing (Cut to Length)
1
2
3
4
5
6
7
8
9
10
11
12*
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
NS
220V 50Hz
31430C
36085C
36195C
35768C
36050C
66576C
Fan - Motor 4w 230V 50/60 Hz
Compressor Serv. Pak EM 65 220V
Overload
Cover - Relay
Relay
Heat Exchanger
PART. NO. DESCRIPTIONITEM NO.
5
12*
13
14
15
16
*INCLUDES RELAY & OVERLOAD. IF UNDER WARRANTY,
REPLACE WITH SAME COMPRESSOR USED IN ORIGINAL
ASSEMBLY.
NOTE: All correspondence pertaining to any of the above
water coolers or orders for repair parts MUST include Model
No. and Serial No. of cooler, name and part number of re-
placement part.
COLOR TABLE
PANEL COLOR Item No. 36
Part No.
Almond Vinyl
Platinum Vinyl
Stainless Steel
Slate Vinyl
26942C
26943C
26948C
26949C
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
PRINTED IN U.S.A. FOR PARTS CONTACT YOUR LOCALDISTRIBUTOR OR VISIT OUR WEBSITE WWW.HALSEYTAYLOR.COM