Halsey Taylor HRFG-EBP User manual

97715C (Rev. B - 5/04)
HRFGEBP_A, HRFGSBP_A
Halsey Taylor Owners Manual
Non-Refrigerated Marblyte Fountain
with Back Panel
To assure you install this model easily and correctly, PLEASE
READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING
THE INSTALLATION. CHECK YOUR INSTALLATION FOR
COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER
APPLICABLE CODES. After installation, leave these instruc-
tions inside the fountain for future reference.
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY
OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK
INTO A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN
INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING
THE PROPER MATERIALS AS INDICATED.ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER
SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING
PLUMBING SYSTEM.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
Installer

97715C (Rev. B - 5/04)
HRFGEBP_A, HRFGSBP_A
FIG. 1
PAGE 2
FINISHED FLOOR
HRFG-EBP, HRFG-SBP ROUGH-IN
MARBLYTE BACK PANEL
DETAIL 1
LEGEND:
A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4" O.D. DRAIN
C = MOUNTING HOLES FOR SECURING FOUNTAIN TOWALL

97715C (Rev. B - 5/04)
HRFGEBP_A, HRFGSBP_A
PAGE 3
1. Wall should already be framed for the fountain using the positioning dimensions shown in Fig. 1.
Shown dimensions pertain to installation location (framing must support up to 150 lbs. weight).
2. Install rough-in plumbing as shown in Fig. 1. Run supply water inlet line and connect to a
service stop (not provided). Turn on supply water and flush thoroughly. Close water supply.
3. Remove bottom access panel from fountain basin and save the screws. Install the fountain to the back
panel and wall using (4) 5/16" bolts and washers (not provided). Bolts should be long enough to securely
fasten the fountain to the wall. Tighten securely, but do not over tighten. Over tightening will crack the
Marblyte Fountain.
4. Remove elbow from end of p-trap (item 1) and attach it to drain tube. Re-attach elbow to p-trap and
cut waste tube to required length using plumbing hadware and trap as guide.
5. Make water supply connections from service stop to the fountain strainer (item 16) by inserting the
water inlet line into the inlet side of strainer until it reaches a positive stop about 3/4", (See Figure 6,
Page 7). Turn on water supply and check for leaks. Newly installed water supply line should be
insulated after leak check is completed. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER
AS DAMAGE TO THE O-RINGS MAY RESULT.
6. These products are designed to operate on 20-105 PSIG supply line pressure. If inlet pressure is
above 105 PSIG, a pressure regulator must be installed in the supply line. Any damage caused by
reason of connecting these products to supply line pressure lower than 20 PSIG or higher than 105 PSIG
is not covered by warranty.
7. Check stream height from bubbler. Stream height is factory set at 45-50 PSI. If supply pressure
varies greatly from this, remove items 8 & 12 (See Figure 3, Page 6) by loosening set screw (item 15)
and adjust the screw on regulator (item 14). Clockwise adjustment will raise stream height and counter-
clockwise adjustment will lower stream height. For best adjustment stream height should be approxi-
mately 1-1/2" (38mm) above the bubbler guard (See Figure 7, Page 7).
8. Replace bottom access panel to fountain basin using screws provided. Tighten securely.
INSTALLATION INSTRUCTIONS
MARBLYTE BACK PANEL
Care and Maintenance of Halsey Taylor Marblyte Fountains
Marblyte provides an exremely durable, nonporous surface which resists staining. Care is very simple.
Routine cleaning with a soft sponge or cloth, or with water or non-abrasive aerosol foam cleaner, is all that is
normally needed to give many years of trouble free service. Cleaners left standing on the fountain surface
can dull the surface finish. Be certain to rinse all cleaning agents completely and polish with a soft cloth.
Harsh abrasive cleaners are not required and should not be used.
Mild abrasives such as liquid automotive cleaning compound or baking soda paste will remove simple
scratches and stains. Cigarette burns can normally be removed without noticeable effect. Deeper
scratches or gouges can be corrected with fine grit sandpaper (240 grit then 400 grit) or a green Scotchbrite
pad.
To maintain or regain luster and make cleaning easier, periodic applications of automobile wax or like
products will keep the finish looking like new.

97715C (Rev. B - 5/04)
HRFGEBP_A, HRFGSBP_A
PAGE 4
HRFG-EBP, HRFG-SBP ROUGH-IN
STAINLESS STEEL BACK PANEL
FIG. 2
FINISHED FLOOR
LEGEND:
A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT
STUBBED 1-1/2"(38mm) FROM WALL SHUT OFF BY OTHERS
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4" O.D. DRAIN
STUBBED 6-5/8"(168mm) FROM THE WALL
C = 1-1/4" TRAP FURNISHED
D = MOUNTING HOLES FOR SECURING FOUNTAIN TO WALL(BLOCKING & WALL SUPPORT IS REQUIRED IN THESE AREA FOR PROPER SUPPORT OF FOUNTAINS)

97715C (Rev. B - 5/04)
HRFGEBP_A, HRFGSBP_A
PAGE 5
INSTALLATION INSTRUCTIONS
STAINLESS STEEL BACK PANEL
1. Wall should already be framed for the fountain using the positioning dimensions
shown in Fig's. 2. Shown dimensions pertain to installation location
(framing must support up to 150 lbs. weight). These dimensions are required for
compliance with ANSI Standard A117.0.
2. Attach wall plate assembly to wall as shown in Fig's. 2 using 5/16" x 2" long
bolts and flat washers (not provided). Tighten securely. (Fastener must match wall
type, i.e. lag screws for wood studs, bolts and anchors for masonary construction.)
3. Install back panel. Place the upper edge of the panel above hanger on the wall.
Slide the panel down until it engages the hanger. Be sure back panel is firmly
engaged before releasing it.
4. Install rough-in plumbing as shown in Fig. 2. Waste line should extend a
minimum of 2" (51mm) thru the back panel. Run supply water inlet line thru back panel.
Install a service stop (not provided). Turn on supply water and flush thoroughly.
5. Remove bottom access panel from fountain basin and save the screws. Install the
fountain to the back panel and wall using (4) 5/16" x 1-1/4" long bolts and washers
thru holes in back panel. Bolts should be long enough to securely fasten the
fountain to the wall. Tighten securely, but do not over tighten. Over tightening will crack
the Marblyte Fountain.
6. Remove elbow from end of p-trap (item 1) and attach it to drain tube. Re-attach elbow
to p-trap and cut waste tube to required length using plumbing hadware and trap as guide.
7. Make water supply connections from service stop to the fountain strainer (item 16) by
inserting the water inlet line into the inlet side of strainer until it reaches a positive stop
about 3/4", (See Figure 6, Page 7). Turn on water supply and check for leaks. Newly
installed water supply line should be insulated after leak check is completed. DO NOT
SOLDER TUBES INSERTED INTO THE STRAINER AS DAMAGE TO THE O-RINGS
MAY RESULT.
8. These products are designed to operate on 20-105 PSIG supply line pressure. If
inlet pressure is above 105 PSIG, a pressure regulator must be installed in the supply
line. Any damage caused by reason of connecting these products to supply line
pressure lower than 20 PSIG or higher than 105 PSIG is not covered by warranty.
9. Check stream height from bubbler. Stream height is factory set at 45-50 PSI. If supply
pressure varies greatly from this, remove items 8 & 12 (See Figure 3, Page 6) by loosening
set screw (item 15) and adjust the screw on regulator (item 14). Clockwise adjustment will
raise stream height and counter-clockwise adjustment will lower stream height. For best
adjustment stream height should be approximately 1-1/2" (38mm) above the bubbler guard
(See Figure 7, Page 7).
8. Replace bottom access panel to fountain basin using screws provided. Tighten
securely.

97715C (Rev. B - 5/04)
HRFGEBP_A, HRFGSBP_A
FIG. 3
812 9
BASIN
314
24 6
10
SEE FIG. 7
TOP VIEW
17, 22
19
18 1
21
2, 4, 20 16
11 5, 7
SEE FIG. 3
13
FIG. 4
PAGE 6
23
15
25

97715C (Rev. B - 5/04)
HRFGEBP_A, HRFGSBP_A
TUBE IS
SECURED
IN POSITION
SIMPLY PUSH IN
TUBE TO ATTACH
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
FIG. 6
OPERATION OF QUICK CONNECT FITTINGS
FIG. 5
NOTE: WATER FLOW
DIRECTION
BUILDING WATER INLET
SERVICE STOP
(NOT FURNISHED)
1/4" O.D. TUBE
WATER INLET
TO COOLER
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY
FIG. 7
PAGE 7

97715C (Rev. B - 5/04)
HRFGEBP_A, HRFGSBP_A
PARTNO.ITEM NO.
PARTS LIST
Drain
Drain-Aztec Gold
Scr, 10-24 x 1/2 PH TR HD-Z
Nut-reg. retain 1-1/8 - 24
Bottom - Plate (HRFG-E)
Bottom - Plate (HRFG-S)
Strainer-Beehive
Strainer-Beehive Aztec Gold
Hex - Nut
Ferrule-Tailpipe
Ferrule-Tailpipe Aztec Gold
Push Button
Push Button-Aztec Gold
Push Button Sleeve
Push Button Sleeve-Aztec Gold
Regulator Holder
Bubbler Assy
Bubbler Assy-Aztec Gold
Push Button - Extension
Fountain - Galaxy Gray (HRFG-E)
Fountain - Galaxy Gray (HRFG-S)
Fountain - Golden Sand (HRFG-E)
Fountain - Golden Sand (HRFG-S)
Fountain - Black (HRFG-E)
Fountain - Black (HRFG-S)
Regulator
Screw #6-32 x .31" Set
Strainer
Panel - Back Galaxy Gray (E)
Panel - Back Galaxy Gray (S)
Panel - Back Black (E)
Panel - Back Black (S)
Panel - Back Golden Sand (E)
Panel - Back Golden Sand (S)
Panel - Back Stainless Steel(S)
Panel - Back Stainless Steel(E)
Bubbler Locknut
Gasket - Black
Insert - Threaded
Nipple Assembly
Wall Plate Assy HRF-SBP
Wall Plate Assy HRF-EBP
Nut - Regulator Mounting
Screw #6-32 x .12" Set
Poly Tubing (Cut To Length)
LK464
LK464AG
112627543890
15005C
27658C
27201C
40038C
45364C
40045C
40619C
45360C
45662C
45408C
45738C
45750C
50986C
51544C
45396C
56087C
56053C
55969C
56057C
55970C
56056C
56025C
61313C
70022C
55996C
56028C
56031C
56027C
56030C
56029C
56032C
23187C
23189C
70012C
100322740560
75554C
15029C
28158C
28170C
45736C
70023C
56092C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
DESCRIPTION
Orifice Assy: Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposits may be removed from the
orifice with a small round file not over 1/8" diameter or small diameter wire. CAUTION: DO NOT file or cut orifice material.
Stream Regulator: If orifice is free of material deposits, regulate flow as in instructions on page 3(Step 7) or page 5(Step 9). If
replacement is necessary, see parts list for correct regulator part number.
Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize an o-ring water seal. To
remove tubing from the fitting, relieve water pressure, push in on the gray collar while pulling on the tubing.(See Figure 6, Page 7). To
insert tubing, push tube straight into fitting until it reaches a positive stop, approximately 3/4".
CAUTION: Cleaning of Aztec Gold Models requires special care. Outer surfaces must be cleaned with detergent or mixture of
vinegar and water only, rinsed and wiped dry. Abrasive and acidic cleaners may eventually damage the Aztec Gold finish.
TROUBLE SHOOTING & MAINTENANCE
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
PRINTED IN U.S.A.
PAGE 8