Halytech Illuminator User manual

4
4. Wait 30 seconds
5. Open browser on PC and enter the following: 192.168.0.188
6. Log in, User Name is “user” and Password is “changeme” (without inverted
commas)
ConfiguringYourIlluminator

Once you have logged in, click “Settings”, then click “Change Settings” and:
1. Set date and time
2. Set username and password for security
3. Set Location & Lighting Setup– to your site name, help person details,
lighting details and costs
4. Optional - set up Status Inputs
5. Optional - set up Alarms and what you want to happen on the alarm
6. Set up Network parameters
7. Set up E-mail parameters
8. Set up your automatic reports
9. Exit Change Settings
Click “Users” on the main screen to set up a unique PIN for each user and choose the
fields they can access by clicking “Change” next to that user.
NOTE: the first user is the administrator with permanent access to all fields
Click “Lights” on the main screen and set periods in each weekday during which normal
users can control lights. Click any link in the "Today's Availability” column to change the
control periods for all fields.
Finally - it is strongly advised that you check e-mail functionality as described in
Appendix D of the User Manual.
Illuminator Quick Start Guide, revised 13/04/2016
© Halytech 2016
Tel: [phone] Email: s[email protected]
PO Box 6983 Baulkham Hills Business Centre NSW 2153
ABN 51 094 853 068
Please refer to “Normal Operation” in the User Manual for detailed information.
Please refer to Appendix A “ Connecting to an Illuminator Locally” in the User
Manual for detailed information.
Please refer to “Setting up an Illuminator for the first time” in the User Manual for
detailed information.
Illuminator Quick Start Guide
V2.26
This guide is not a replacement for the User Manual. Please refer to the complete
Illuminator manual available for download from:
http://www.halytech.com.au/images/downloads/illuminator
PartsList(includedinthebox)
 1 x Illuminator
 1 x Whip antenna and bracket
 1 x Comms cable (red Ethernet crossover)
 1 x connector bag containing:
o 4 x 8-pin I/O connectors
o 2 x 2-pin power connectors
o 1 x 4-pin Aux connector
o 8 x 120-ohm resistors (for 4-20mA inputs)
o 8 x protection diodes (to protect control outputs)
 1 x Quick Start Guide (this document)
NOTE: A new Illuminator is shipped without a SIM card
Commonoptionalcomponents(purchasedseparately)
 15V DC power supply
 12V DC SLA (sealed lead acid) battery
 Powder-coated steel enclosure
 Keypad
 External relays and contactors
 Electricity meters

2
InstallingaSIMCard
You will need a full-size SIM card with SMS and internet services enabled. To connect to an
Illuminator remotely to add users, change PINs etc., obtain a SIM card on a post-paid plan
from Telstra and request that a dynamic public IP address added to you SIM. Simply
advise Telstra to set the following parameters on your SIM: 'GPTEXB3' and 'GPCORPB3'
1. Put the SIM card in a standard mobile phone and disable any PINs.
2. Unscrew the modem access cover located on the top of the Illuminator case,
next to the antenna connector.
3. Look at the SIM slot and ensure the black locking lever is in the unlocked (left)
position. A small flat screwdriver is useful. Very little force is required.
4. Gently push the SIM card into the slot so that it is level with the locking lever,
notch-first and contacts-up. The last few mm is spring-loaded and you will feel
it click into place.
5. Gently slide the black locking lever to the right until it clicks.
6. Screw the modem access cover
Guide
Locking Lever
SIM Slot
Unlocked position Locked (working) position
Please refer to Appendix C “ Connection to Mobile Network” in the User Manual.
3
ConnectingtheAntennaandPower
1. Connect the antenna to the jack next to the SIM card holder– finger tight only
2. Connect Power or Solar Panel and Battery using the supplied connectors to
the CHG and BAT terminals respectively.
ConnectingControls

Using the connectors provided - connect Controls as per manual
 You must use external isolation relays as the inbuilt controls cannot
switch mains power. Use supplied protection diodes on the external
isolation relays.
ConnectingInputs(Optional)

Using supplied connectors, connect Inputs as per manual
 Switch, pulse and event inputs - connected directly
 4-20mA – connect supplied 120 Ohm resistor across input
 Voltage inputs – connected via dividing resistors (not supplied)
 If metering is enabled, the input number and control number used for the
electricity meter and contactor respectively must match.
ConnectingtheIlluminatortoyourPC
1. Make sure that your PC is not connected to the Illuminator
2. Turn Illuminator on by pressing the button and holding it till the LCD
backlighting turns on
IMPORTANT: the backlighting must be ON before a connection can be made
3. Using the supplied red LAN crossover cable connect your PC to the
Illuminator
Please refer to "Physical Connections” in the User Manual for detailed information.
Please refer to "Physical Connections” in the User Manual for detailed information.
Please refer to "Physical Connections” in the User Manual for detailed information.