Hamilton Beach Professional B79 User manual

GB Blender
Operation Manual
(Original Instructions) (2)
Visit https://hamiltonbeach.global for our complete
line of products and Use and Care Guides – as well as
delicious recipes, tips, and to register your product online.
AR
(20)
ZH 多功能高速破壁攪拌機
操作手冊 (36)
請訪問 https://hamiltonbeach.global ，查看我們的完
整產品系列以及使用和保養指南、美味食譜和
小貼士，並在線註冊購買的產品！ .
MS Pengisar
Manual Pengendalian (52)
Lawati https://hamiltonbeach.global untuk barisan
produk kami yang lengkap dan Panduan Penggunaan
dan Penjagaan – begitu juga dengan resipi yang sedap,
tip dan untuk daftar barang anda secara dalam talian.
FR Mélangeur
Manuel d’utilisation (68)
Rendez-vous sur le site Internet https://hamiltonbeach.global
pour consulter notre gamme complète de produits ainsi que nos
guides d’utilisation et d’entretien - vous pourrez aussi consulter
de délicieuses recettes, des astuces et enregistrer votre produit
en ligne !
Type: B79
840316700 | 05/19
Hamilton Beach Brands, Inc.
Glen Allen, VA 23060

2
IMPORTANT SAFEGUARDS
1. Read all instructions.
2. This appliance is not intended
for use by persons with
reduced physical, sensory
or mental capabilities, or
lack of experience and
knowledge, unless they
are closely supervised and
instructed concerning use
of the appliance by a person
responsible for their safety.
3. This appliance shall not be
used by children. Keep the
appliance and its cord out of
reach of children.
4. Close supervision is
necessary when any
appliance is used near
children. Children should be
supervised to ensure that they
do not play with the appliance.
5. Cleaning and user
maintenance shall not be
performed by children unless
they are supervised.
6. To protect against risk of
electrical shock, do not put
cord, plug, base, or motor in
water or other liquid.
7. Turn the appliance OFF( ),
then unplug from socket when
not in use, before putting on
or taking off parts, and before
cleaning. To unplug, grasp
the plug and pull from the
socket. Never pull from the
power cord.
8. Avoid contact with moving
parts.
9. Do not operate any appliance
with a damaged supply cord
or plug, or after the appliance
malfunctions or has been
dropped or damaged in
any manner. Supply cord
replacement and repairs
must be conducted by the
manufacturer, its service agent,
or similarly qualified persons
in order to avoid a hazard.
Call the provided customer
service number for information
on examination, repair, or
adjustment.
When using electrical appliances, basic safety precautions should always be
followed to reduce the risk of fire, electric shock, and/or injury to persons,
including the following:
GB

3
10. The use of attachments,
including canning jars, not
recommended or sold by
the appliance manufacturer
may cause a risk of injury to
persons.
11. Do not use outdoors.
12. Do not let cord hang over
edge of table or counter or
touch hot surfaces, including
stove.
13. Do not place on or near a hot
gas or electric burner, or in a
heated oven.
14. Keep hands and utensils,
other than the tamper
provided, out of container
while blending to reduce the
risk of severe injury to persons
or damage to the blender.
The cover must remain in
place when using the tamper
through the cover opening.
Ascraper may be used but
must be used only when the
blender is not running.
15. Blades are sharp; handle
carefully— especially when
emptying or cleaning the
blender jar.
16. Do not use a broken,
chipped, or cracked blender
jar.
17. Be careful if hot liquid is
poured into the blender as
it can be ejected out of the
appliance due to a sudden
steaming
18. Do not use broken, cracked,
or loose cutting blade
assembly.
19. Always operate blender
with lid in place. Remove
emulsion cup only for adding
ingredients or to insert the
tamper.
CAUTION: Do not
operate without cover in
place.
20. When blending hot liquids,
close any edge cover opening
intended for pouring. To
prevent possible burns: do
not exceed 1000 ml level. Hot
liquids may push off lid during
blending; therefore, with the
protection of an oven mitt or
thick towel, place one hand on

4
top of the lid, keep exposed
skin away from the lid, and
start blending at lowest speed.
21. Ensure cutter assembly is
tight and secure to jar. Injury
can result if moving blades
accidentally become exposed.
22. Do not leave blender
unattended while it is
operating.
23. Check that the appliance
is OFF ( ) before plugging
cord into wall socket. To
disconnect, turn the control
to OFF ( ); then remove plug
from wall socket. To unplug,
grasp the plug and pull from
the socket. Never pull from
the power cord.
24. Do not use appliance for
other than intended purpose.
25. Be careful if hot liquid is
poured into the blender
container as it can be ejected
out of the appliance due to
sudden steaming.
26. CAUTION! In order
to avoid a hazard due to
inadvertent resetting of the
thermal cut-off, this appliance
must not be supplied through
an external switching device,
such as a timer, or connected
to a circuit that is regularly
switched on and off by the
utility.
27. The plug is provided with a
13-amp fuse approved by
ASTA to B.S. 1362. If
you need a replacement fuse
carrier, it must be replaced
with the same colour-
coded carrier with the same
markings. Fuse covers and
carriers can be obtained from
approved service agents.
28. In manual model do not
exceed normal operating cycle
of 2 minutes ON (I) and 1
minute OFF ( ).
In SMOOTHIE ( ) or
ICE CRUSH ( ) mode allow
appliance to cool for 2 minutes
between each cycle.
In HOT SOUP ( ) mode
allow appliance to cool for 10
minutes between each cycle.
SAVE THESE INSTRUCTIONS

5
Other Consumer Safety Information
This product is intended for household use only.
The length of the cord used on this
appliance was selected to reduce the
hazards of becoming tangled in or tripping
over a longer cord. If a longer cord is
necessary, an approved extension cord
may be used. The electrical rating of
the extension cord must be equal to or
greater than the rating of the appliance.
The extension cord must be a grounding-
type, 3-wire cord. Care must be taken to
arrange the extension cord so that it will
not drape over the countertop or tabletop
where it can be pulled on by children or
accidentally tripped over.
If the Cutting Blade Assembly locks and
will not move, it will damage the motor.
Do not use. Call customer service number
for information.
Do not place Blender Jar in the freezer
filled with food or liquid. This can result
in damage to the Cutting Blade Assembly,
Jar, Blender, and possibly result in
personal injury.
NOTE: This machine is equipped with motor overload protection. If the motor stops
during operation due to overheating, unplug and allow it to cool down for approximately
15 minutes. Plug machine back in to resume normal operation.
Recycling the Product at the End of Its Service Life
The wheeled bin symbol marked on this appliance signifies that it
must be taken over by a selective collection system conforming to the
WEEE Directive so that it can be either recycled or dismantled in order
to reduce any impact to the environment. The user is responsible for
returning the product to the appropriate collection facility, as specified
by your local code. For additional information regarding applicable
local laws, please contact the municipal facility and/or local distributor.

6
Parts and Features
RESET/OFF (Power) (I/ ) Switch/
Circuit Breaker (on side of Base)
Blender
Jar
Base
Lid
Emulsion Cup
Tamper
START/STOP
() Button
Before first use: After unpacking the Blender, follow the instructions in “Cleaning Your
Blender.”
Cutting
Blade
Assembly
PULSE
() Button
Program
Buttons (4)
Variable
Speed Dial
Jar Pad
Speed Indicator
Lights
Model: 58928-SAU
Type: B79
Ratings:
220–240 V~ 50–60 Hz 1400 W

7
RESET/OFF (I/ ) (Power) Switch/Circuit Breaker:
The RESET/OFF (I/) (Power) Switch is located on the right-hand side of
the Blender Base. This switch controls power to the Blender. This switch
is also a circuit breaker that, if tripped, must be turned off and back on to
reset.
Control Panel
Emulsion Cup: The Emulsion Cup helps create dressings and sauces that require slowly
adding liquid ingredients into the Blender Jar while the Blender is in operation.
Lid: The Lid is easy to put on, take off, and clean. Always use the Lid and the Emulsion
Cup when the machine is in operation.
Blender Jar: Volume measures are clearly marked.
Tamper: The Tamper helps mix thick or frozen recipes that cannot be processed with
regular blending. It prevents air pockets from forming and is a handy tool when making
nut butters or frozen desserts.
Automatic Overload Protection: This machine is equipped with motor overload
protection. If the motor stops during operation due to overheating, unplug and allow
it to cool down for approximately 15 minutes. Plug machine back in to resume normal
operation.
PULSE ( ) Button:
Press and hold down the PULSE ( ) Button to blend at the speed setting
shown on the VARIABLE SPEED DIAL in MANUAL mode.
Variable Speed Dial:
The Variable Speed Dial can be adjusted to
the desired speed when blending in Manual
mode. The Speed Indicator Light(s) will
illuminate to show the selected speed.
Program Buttons:
There are four program settings: HOT SOUP
(), SMOOTHIE ( ), ICE CRUSH
( ) , and
WHOLE JUICE ( ). Select the desired
program by pressing the button for that
program. The Speed Indicator Light(s) will
illuminate to show the programmed speeds.
START/STOP ( ) Button:
The START/STOP ( ) Button is used to begin or end the MANUAL
mode or to stop a program before the cycle ends.

8
Using Your Blender
Before first use: After unpacking the Blender, follow the instructions in “Care and Cleaning.”
IMPORTANT:
The Blender Jar and Cutting Blade Assembly are subject to wear during normal
use. Always inspect Jar for nicks, chips, or cracks. Always inspect Cutting Blade Assembly for
broken, cracked, or loose blades. If Jar or Cutting Blade Assembly is damaged, do not use.
5. Plug in Blender. Move the RESET/OFF (I/
) Switch to the RESET (I) position to
turn on power to the Blender and ready
it for blending. The front lights will come
on. Move the RESET/OFF (I/) Switch to
the OFF ( ) position and remove plug
from socket anytime the machine is left
unattended. If Blender is plugged in and
Switch is in ON (I) position, but panel
lights are not illuminated, the Blender has
entered standby mode. This will happen
after 3 minutes of inactivity. Press any
control panel button to resume normal
operation.
1. Place Blender Jar on base. 2. Add ingredients.
3. Place Lid on Jar. Insert the Emulsion
Cup into the Lid and secure by turning
clockwise. Remove cup to use the
Tamper or to add ingredients.
4. Remove Emulsion Cup; rotate
counterclockwise from “locked” to
“unlocked” position and lift out. Insert
Tamper into hole in Lid.
NOTE: Turn Blender OFF ( ) before
removing Emulsion Cup and when
adding the Tamper.

9
IMPORTANT: To remove the Lid, use your finger to pull up on the front tab. Do not twist the
Lid to take it off the Jar — this might harm the Lid material and prevent it from sealing the
Blender Jar.
How to Open Blender Lid
4. Continue to hold the front tab with your
finger and use thumb to support the Lid
until it completely opens.
1. Hold Jar handle firmly. 2. To open Lid, place a finger on the front
tab.
3. Apply a small amount of force on Lid
until Lid is separated from the Jar.

10
The HOT SOUP ( )
program purees
ingredients at
high speeds. As a
result, friction heats
ingredients. Do not
blend more than
1000 ml on this
program. When
making soups, start
with cold or room-temperature ingredients.
The Emulsion Cup can be kept in the Lid.
Blender runs for 6 minutes, 45 seconds.
The SMOOTHIE ( )
program blends
frozen or fresh
smoothies. Blender
pulses three times
at the beginning to
chop ice or frozen
ingredients and then
ramps up to run on
high speed. Blender
runs for total 45
seconds.
When a recipe calls
for making a fruit or
vegetable juice, run
the WHOLE JUICE
() program. The
WHOLE JUICE
program gives a
smooth consistency
to pureed fruit or
vegetables and a fine
texture when whole
grains or seeds are included in the juice
recipe. It is great for blending more fibrous
fruits and vegetables into a delicious,
healthy juice. The Blender ramps up from
low to high, running for total 55 seconds.
Using Program Settings
Programs are optimized for recipe categories and vary in blending speed
and duration. Pressing a Program Button illuminates only the program
selected. The Blender automatically starts when the Program Button
is pressed and automatically stops at the end of the program. To stop
Blender before program cycle ends, press START/STOP ( ) Button or
the Program Button. This will stop the Blender and return it to MANUAL
mode. Pressing a Program button again will start the Blender from the
beginning of the selected program.
The ICE CRUSH ( )
setting breaks ice
into pieces small
enough for slushies
or fine cocktails.
Blender continuously
pulses from low to
medium for 1 minute.

11
Using Manual Mode
2. Press START/STOP () and slowly
rotate the VARIABLE SPEED DIAL to
the right or left during blending to
increase or decrease blending speed.
When pressing PULSE (), the
Blender will run at selected speed
until the PULSE () Button is released.
wWARNING Burn Hazard. When
using HOT SOUP ( )Mode or blending
hot liquids, do not fill Blender Jar with
liquid beyond the 1000 ml level. With
the protection of an oven mitt or thick
towel, place one hand on top of Lid.
Keep exposed skin away from Lid. Start
blending at lowest speed.
3. Place one hand on top of Lid to move
thick mixtures around in Blender Jar.
1. Rotate the VARIABLE SPEED DIAL to
leftmost.

12
4. At the end of the blending cycle,
rotate the VARIABLE SPEED DIAL
back to the leftmost position and
press the START/STOPw( )Button
to stop blending. Turn off the Blender
with the RESET/OFF (I/) Switch.
Unplug Blender after blending.
5. Remove Blender Jar.
6. Remove Lid while holding blending
Jar securely. Serve.
Using Manual Mode (cont.)
wWARNING Burn Hazard.
Metal parts under
blending Jar get hot
after extended use.

13
Blender Tips
• To add foods when Blender is operating,
remove Emulsion Cup and add
ingredients through the opening.
• For best performance, the minimum
amount of liquid needed per recipe is
one cup (8 ounces [237 ml]). Add more
liquid if food is not blending properly.
The amount of liquid needed will vary
based on the other ingredients required
for blending.
• If blending action stops during blending
or ingredients stick to sides of Jar,
remove Emulsion Cup and insert Tamper
to help move the mixture around or add
more liquid to Blender Jar.
• Do not store food or liquids in Blender
Jar.
• Avoid bumping or dropping Blender
when in operation or at any time.
• Use Tamper when making nut butters
and blend in 1-minute intervals.
• Cutting large whole fruits and
vegetables may allow them to blend
more quickly.
• Do not fill Blender Jar past highest
graduation marking.
• Always place liquid in Blender Jar first,
then remaining ingredients.
• If ice or frozen fruit pieces are not
blending, stop the Blender and pulse a
few times.
• Do not allow ice to stand or freeze
in Jar. Immediately crush ice after
placing in Jar.
NOTE: This machine is equipped
with motor overload protection. If the
motor stops during operation due to
overheating, unplug and allow it to cool
down for approximately 15 minutes.
Plug machine back in to resume normal
operation. (See “Troubleshooting” on
page 15.)
Blender and Accessory Tips
Using the Tamper
• The hand protector on the Tamper and
the Lid work together to prevent the
Tamper from hitting the blades when the
Lid is secured properly on the Blender Jar.
• The Blender Jar should not be more than
two-thirds full when the Tamper is used
during blending.
• Only use the Tamper provided with this
model Blender. Do not use Tampers made
for any other Blender or Blender model.
• If food does not circulate, an air bubble
may be trapped in the mixture. Remove
the Blender Jar from the Blender base.
Remove the Emulsion Cup. Release
the air bubble by inserting the Tamper
through the Emulsion Cup opening.
• Holding the Tamper straight down may
not help ingredients circulate. If necessary,
point the Tamper toward the sides or
corners of the Blender Jar. DO NOT try to
force the Tamper deeper into the Jar.

14
Care and Cleaning
3. Wipe Blender base, control panel, and
cord with a damp cloth or sponge. To
remove stubborn spots, use a mild,
nonabrasive cleanser.
DO NOT use the “SANI” setting when
washing in the dishwasher. “SANI”
cycle temperatures could damage your
product. Parts may also be washed
with hot, soapy water. Rinse and dry
thoroughly. Do not soak.
NOTES:
• BLENDER JAR IS HAND WASH ONLY. Alternative is to fill Jar halfway with water and
add 2–3 drops of dish soap. Blend for 30 seconds. Rinse and dry thoroughly.
• To clean after blending oily foods, sprinkle 1/4 cup (59 ml) baking soda in Blender.
Add 1 cup (237 ml) white vinegar. Mixture will bubble. When bubbling subsides, add
2 cups (473 ml) water and blend on the HOT SOUP ( ) cycle. Wash any remaining
residue with dish soap and water. Rinse and dry thoroughly.
1. Unplug Blender. 2. Remove Jar, Lid, and Emulsion Cup.
wWARNING
Electrical Shock Hazard.
Disconnect power before cleaning. Do not immerse
cord, plug, base, or motor in water or other liquid.
wWARNING
Burn Hazard.
Metal parts under blending Jar get hot after
extended use.
DISHWASHER-SAFE

15
Troubleshooting
Error Messages
All Program Buttons are flashing.
• The motor has overheated during use. Turn RESET/OFF (I/ )
(Power) Switch to OFF ( ) and allow to cool for 15 minutes.
Flip RESET/OFF (I/) (Power) Switch to RESET (I), and resume
normal operation.
The SMOOTHIE ( ) and ICE CRUSH ( ) Buttons are flashing.
• Remove the Blender Jar and Lid. Stir contents. Replace Lid.
Press HOT SOUP ( ) Button. If the problem persists, turn unit
off, unplug from electrical socket, and contact the customer
service center.
The HOT SOUP ( ) and WHOLE JUICE ( ) Buttons are
flashing.
• The Blender speed has ramped up to high too quickly and
run on high speed. Turn the unit off, unplug from the electrical
socket, and call the customer service center.
Blender is plugged in and switch is in ON (I) position, but panel
lights are not illuminated.
• Blender enters standby mode after 3 minutes of inactivity to
conserve power. Press any control panel button or switch to
resume normal operation.
NOTE: Buttons start flashing 10 seconds after a problem
has occurred.

16
Troubleshooting (cont.)
Blender fails to start and Program Lights are not illuminated.
• Make sure that the main power
RESET/OFF (I/) Switch is in the RESET (I) position.
• Check to see if unit is securely plugged into an electrical socket of the proper voltage and
frequency.
• Check to see if the fuse for the electrical socket has blown or if a circuit breaker has
tripped.
Blender stops while it is running and the Program Lights are illuminated.
• This Blender is equipped with motor overload protection. If the motor stops during
operation due to overheating, unplug and allow the Blender to cool down. Plug Blender
back in after 15 minutes.
• Resume normal operation.
Blender stops while running and START/STOP ( ) Button flashes.
• Mixture in Blender is too heavy of a load on the motor. This Blender is programmed to
stop running to protect itself from electrical damage. Remove some of the ingredients
from the Blender Jar. Turn VARIABLE SPEED DIAL to 1 and press the START/STOP ( )
switch to continue to process in MANUAL mode. Increase speed as necessary. If this issue
happens again, remove more of the Blender mixture and start the process again.
Ingredients will not mix properly.
• Check to see if enough liquid has been added to the ingredients. Mixture should be fluid
and free-running at all times.
• Solid pieces are too large.
• Container is too full. Do not fill past highest 1800 ml graduation marking.
• Cutting Blades are not sharp or are damaged. Inspect container and Cutting Assembly
daily.
• Select speed to create a fluid blend.
Blender smells like it is burning.
• Turn off Blender and allow unit to cool.
• Although motors are tested during the manufacturing process, heavy use may cause
curing of motor windings. The smell may quickly dissipate after a few heavy uses.
• If smell continues after additional heavy uses, call our customer service center.
There is grease around the bottom of the Blender Jar or on the counter top.
• Monitor the problem and source. This may indicate an issue with the Jar bearings.
• Call our customer service center if the condition persists.
Blender Jar is cloudy or stained.
• Some cloudiness may be natural after use. The minerals from fruits, produce, and leafy
greens, in addition to the oils of various nut butters, can sometimes cause a film on the
Blender Jar or may be difficult to clean.
• Sprinkle 1/4 cup (59 ml) baking soda in Blender. Add 1 cup (237 ml) white vinegar.
Mixture will bubble. When bubbling subsides, add 2 cups (473 ml) water and blend on
the HOT SOUP ( ) cycle. Wash any remaining residue with dish soap and water. Rinse
and dry thoroughly.
Blender fails to start.
• Jar is not in place.

17
Notes

18

19

20