Hamilton Beach Professional 58911-CN User manual

READ BEFORE USE
使用前阅读
Questions?
問題？
www.hamiltonbeach.cn
Blender
多功能
高速破壁
料理机
English .................2
简体中文..............14

2
IMPORTANT SAFEGUARDS
1. Read all instructions.
2. This appliance is not intended for use
by persons (including children) with
reduced physical, sensory, or mental
capabilities, or lack of experience and
knowledge, unless they are closely
supervised and instructed concerning
use of the appliance by a person
responsible for their safety.
3. Close supervision is necessary when any
appliance is used by or near children.
Children should be supervised to ensure
that they do not play with the appliance.
4. To protect against risk of electrical shock,
do not put cord, plug, base, or motor in
water or other liquid.
5. Unplug cord from outlet when not in
use, before putting on or taking off parts,
and before cleaning.
6. Avoid contact with moving parts.
7. Do not operate any appliance with a
damaged cord or plug, or after the
appliance malfunctions, or is dropped
or damaged in any manner. All repairs
must be conducted by the manufacturer,
its service agent, or similarly qualified
persons in order to avoid a hazard. Call
the provided customer service number.
8. The use of attachments, including
canning jars, not recommended or sold
by the appliance manufacturer may
cause a risk of injury to persons.
9. Do not use outdoors.
10. Do not let cord hang over edge of
table or counter or touch hot surfaces,
including stove.
11. Do not place on or near a hot gas or
electric burner, or in a heated oven.
12. Keep hands and utensils out of the jar
and away from the cutting blade, while
blending or chopping food, to reduce
the risk of severe personal injury and/
or damage to the blender or available
attachments (attachments may not be
provided with blender). A rubber spatula
may be used but must be used only
when blender is not running.
13. Blades are sharp; handle carefully—
especially when emptying or cleaning
the blender jar.
14. Do not use a broken, chipped, or
cracked blender jar.
15. Do not use broken, cracked, or loose
cutting blade assembly.
16. Always operate blender with lid in place.
Remove emulsion cup only for adding
ingredients or to insert the tamper.
17. When blending hot liquids, secure
emulsion cup and close any edge cover
opening intended for pouring. To prevent
possible burns: Do not exceed the 6-cup
(1420-ml) level. Hot liquids may push off
lid during blending; therefore, with the
protection of an oven mitt or thick towel,
place one hand on top of the lid, keep
exposed skin away from the lid, and start
blending at lowest speed.
18. Ensure cutter assembly is tight and
secure to jar. Injury can result if moving
blades accidentally become exposed.
19. Do not leave blender unattended while it
is operating.
20. Before plugging cord into wall outlet,
turn off the appliance. To disconnect
cord, switch to OFF (O). Then remove
plug from wall outlet.
21. Do not use appliance for other than
intended purpose.
22. CAUTION: In order to avoid a hazard
due to inadvertent resetting of the
thermal cut-off, this appliance must
not be supplied through an external
switching device, such as a timer, or
connected to a circuit that is regularly
switched on and off by the utility.
When using electrical appliances, basic safety precautions should always be followed to
reduce the risk of fire, electric shock, and/or injury to persons, including the following:
SAVE THESE INSTRUCTIONS!

3
Other Consumer Safety Information
This product is intended for household use only.
The length of the cord used on this
appliance was selected to reduce
the hazards of becoming tangled in
or tripping over a longer cord. If a
longer cord is necessary, an approved
extension cord may be used. The
electrical rating of the extension cord
must be equal to or greater than the
rating of the appliance. The extension
cord must be a grounding-type, 3-wire
cord. Care must be taken to arrange
the extension cord so that it will not
drape over the countertop or tabletop
where it can be pulled on by children or
accidentally tripped over.
If the cutting blade assembly locks and
will not move, it will damage the motor.
Do not use. Call the toll-free customer
service number for information.
Do not place blender jar in the freezer
filled with food or liquid. This can
result in damage to the cutting blade
assembly, jar, blender, and possibly
result in personal injury.
NOTE: This machine is equipped with motor overload protection. If the motor stops
during operation due to overheating, unplug and allow it to cool down for approximately
15 minutes. Plug machine back in to resume normal operation.

4
Parts and Features
RESET/OFF (Power)
(I/O) Switch
Blender
Jar
Base
Jar Pad
Lid
Emulsion Cup
Tamper
START/STOP
() Switch
BEFORE FIRST USE: After unpacking the blender, follow the instructions in “Cleaning
Your Blender.”
Cutting
Blade
Assembly
PULSE
() Switch Program
Buttons
Variable
Speed Dial

5
Parts and Features (cont.)
RESET/OFF (I/O) (Power) Switch/Circuit Breaker:
The RESET/OFF (I/O) (Power) switch is located on the right-hand side of
the blender base. This switch controls power to the blender. This switch
is also a circuit breaker that, if tripped, must be turned off and back on to
reset.
Control Panel
Emulsion Cup: The emulsion cup helps create dressings and sauces that require slowly
adding liquid ingredients into the jar while the blender is in operation.
Lid: The lid is easy to put on, take off, and clean. Always use the lid and the emulsion cup
when the machine is in operation.
Blender Jar: Volume measures are clearly marked.
Tamper: The tamper helps mix thick or frozen recipes that cannot be processed with
regular blending. It prevents air pockets from forming and is a handy tool when making
nut butters or frozen desserts.
Automatic Overload Protection: This machine is equipped with motor overload
protection. If the motor stops during operation due to overheating, unplug and allow
it to cool down for approximately 15 minutes. Plug machine back in to resume normal
operation.
PULSE ( ) Switch:
Press and hold down the PULSE ( ) switch to blend at the speed setting
shown on the VARIABLE SPEED DIAL in MANUAL mode.
Variable SPEED Dial:
The center VARIABLE SPEED DIAL
determines the blender speed setting when
blending in MANUAL mode.
Program Buttons:
There are four program settings: HOT SOUP ( ), SMOOTHIE
(), ICE CRUSH ( ), and WHOLE JUICE ( ). Select the
desired program by pressing the button for that program.
START/STOP ( ) Switch:
The START/STOP ( ) switch is used to begin or end the MANUAL
mode or to stop a program before the cycle ends.

6
Using Your Blender
BEFORE FIRST USE: After unpacking the blender, follow the instructions in “Cleaning
Your Blender.”
IMPORTANT:
The blender jar and cutting blade assembly are subject to wear during
normal use. Always inspect jar for nicks, chips, or cracks. Always inspect cutting blade
assembly for broken, cracked, or loose blades. If jar or cutting blade assembly is damaged,
do not use.
1 2
3 4
Plug in blender. Move the RESET/OFF
(I/O) switch to the RESET (I) position
to turn on power to the blender and
ready it for blending. The front lights
will illuminate. Move the RESET/OFF
(I/O) switch to the OFF (O) position
anytime the machine is left unattended.
If blender is plugged in and switch is in
ON (I) position, but panel lights are not
illuminated, the blender has entered
standby mode. This will happen after 3
minutes of inactivity. Press any control
panel button or switch to resume normal
operation.
Place blender jar on base. Add ingredients.
Place lid and emulsion cup on jar. Insert
the cup into the lid and secure by turning
clockwise. Remove the emulsion cup to
use the tamper or to add ingredients.

7
The HOT SOUP ( )
setting purees and
heats ingredients
to just under the
boiling point. Do not
blend more than 6
cups (1420 ml) on
this program. When
making soups, start
with cold or room-
temperature ingredients. The emulsion cup
can be kept in the lid. Blender runs for
5 minutes, 45 seconds.
The SMOOTHIE ( )
setting blends
frozen or fresh
smoothies. Blender
pulses five times
at the beginning to
chop ice or frozen
ingredients and then
ramps up to run on
high speed for
45 seconds.
The ICE CRUSH ( )
setting breaks ice
into pieces small
enough for slushies
or fine cocktails.
Blender continuously
pulses from low to
medium for
1 minute.
When a recipe calls
for making a fruit or
vegetable juice, run
the WHOLE JUICE
() program. The
WHOLE JUICE
setting gives a
smooth consistency
to pureed fruit or
vegetables and a
fine texture when whole grains or seeds
are included in the juice recipe. It is great
for blending more fibrous fruits and
vegetables into a delicious, healthy juice.
The blender slowly ramps up from low to
high, running for 55 seconds.
Using Program Settings
Programs are optimized for recipe categories and vary in blending speed
and duration. Pressing a program button illuminates only the program
selected. The blender automatically starts when the program button
is pressed and automatically stops at the end of the program. To stop
blender before program cycle ends, press START/STOP ( ). Pressing
the program button again will reset the program, and it will start back
from the beginning. Should you press START/STOP ( ) again, the
blender defaults to MANUAL mode.

8
Using Manual Mode
Press START/STOP () and slowly
rotate the VARIABLE SPEED DIAL to the
right or left during blending to increase or
decrease blending speed.
If using PULSE (), the blender will run
at the speed on the dial only when the
PULSE () switch is held down.
2
WARNING Burn Hazard:
Do not
fill blender jar with hot liquid beyond the
6-cup (1420-ml) level. With the protection
of an oven mitt or thick towel, place one
hand on top of lid. Keep exposed skin away
from lid. Start blending at lowest speed.
3 – OPTIONAL
1
Remove emulsion cup and insert
tamper into hole in lid. Rotate cup
counterclockwise from “locked” to
“unlocked” position and lift out.
NOTE: Turn blender OFF (O) before
removing emulsion cup and when
adding the tamper.
4 – OPTIONAL
Rotate the VARIABLE SPEED DIAL to 1.

9
Place one hand on top of lid to move
thick mixtures around in blender jar.
6
7 8
5
At the end of the blending cycle, rotate
the VARIABLE SPEED DIAL back to the
1 position and press the START/STOP
()switch to stop blending. Turn off
the blender with the RESET/OFF (I/O)
switch on the right side of the base.
Unplug blender after blending.
Remove blender jar. Remove lid by lifting up on any corner
while holding blending jar securely.
Serve.
Using Manual Mode (cont.)
WARNING Burn Hazard:
Metal parts under
blending jar get hot
after extended use.

10
Blender Tips
•To add foods when blender is operating,
remove emulsion cup and add
ingredients through the opening.
•For best performance, the minimum
amount of liquid needed per recipe is
one cup (8 ounces/237 ml). Add more
liquid if food is not blending properly.
The amount of liquid needed will vary
based on the other ingredients required
for blending.
•If blending action stops during blending
or ingredients stick to sides of jar, insert
tamper to help move the mixture around
or add more liquid to blender jar.
•Do not store food or liquids in blender
jar.
•Avoid bumping or dropping blender
when in operation or at any time.
•Use tamper when making nut butters
and blend in 1-minute intervals.
•Cutting large whole fruits and
vegetables may allow them to blend
more quickly.
•Do not fill blender jar past highest
graduation marking.
•Always place liquid in blender jar first,
then remaining ingredients.
•If ice or frozen fruit pieces are not
blending, stop the blender and pulse a
few times.
•Do not allow ice to stand or freeze in
jar. Immediately crush ice after placing
in jar.
NOTE: This machine is equipped
with motor overload protection. If the
motor stops during operation due to
overheating, unplug and allow it to cool
down for approximately 15 minutes.
Plug machine back in to resume normal
operation.
Using Your Blender (cont.)
Using the Tamper
•The hand protector on the tamper and the
lid work together to prevent the tamper
from hitting the blades when the lid is
secured properly on the blender jar.
•The blender jar should not be more than
two-thirds full when the tamper is used
during blending.
•Only use the tamper provided with this
model blender. Do not use tampers made
for any other blender or blender model.
•If food does not circulate, an air bubble
may be trapped in the mixture. Remove
the blender jar from the blender base.
Remove the emulsion cup. Release the air
bubble by inserting the tamper through
the emulsion cup opening.
•Holding the tamper straight down may
not help ingredients circulate. If necessary,
point the tamper toward the sides or
corners of the blender jar. DO NOT try to
force the tamper deeper into the jar.

11
Cleaning Your Blender
Wipe blender base, control panel, and
cord with a damp cloth or sponge. To
remove stubborn spots, use a mild,
nonabrasive cleanser.
DO NOT use the “SANI” setting when
washing in the dishwasher. “SANI”
cycle temperatures could damage your
product. Parts may also be washed
with hot, soapy water. Rinse and dry
thoroughly. Do not soak.
3 DISHWASHER-SAFE
NOTES:
•HAND WASH ONLY. Alternative is to fill jar halfway with water and add 2–3 drops of
dish soap. Blend for 30 seconds. Rinse and dry thoroughly.
•To clean after blending oily foods, sprinkle 1/4 cup (59 ml) baking soda in blender. Add
1 cup (237 ml) white vinegar. Mixture will bubble. When bubbling subsides, add 2 cups
(473 ml) water and blend on the HOT SOUP cycle. Wash any remaining residue with
dish soap and water. Rinse and dry thoroughly.
1 2
Unplug blender. Remove jar, lid, and emulsion cup.
WARNING
Electrical Shock Hazard:
Disconnect power before cleaning. Do
not immerse cord, plug, base, or motor
in water or other liquid.
WARNING
Burn Hazard:
Metal parts under blending jar get hot after
extended use.

12
Troubleshooting
Error Messages
PROBLEM PROBABLE CAUSE/SOLUTION
All program buttons are
flashing.
• The motor has overheated during use. Turn power switch
to OFF (O) and allow to cool for 15 minutes. Turn power
switch to RESET (I), and resume normal operation.
The SMOOTHIE ( ) and
ICE CRUSH ( ) buttons
are flashing.
• Remove the blender jar and lid. Stir contents and top with
lid. Press HOT SOUP ( ) cycle. If the problem persists,
turn unit off, unplug from electrical outlet, and contact the
customer service center.
The HOT SOUP ( ) and
WHOLE JUICE ( )
buttons are flashing.
• The blender speed has ramped up to high too quickly
and run on high speed. Turn the unit off, unplug from the
electrical outlet, and call the customer service center.
Blender is plugged in
and switch is in ON (I)
position, but panel lights
are not illuminated.
• Blender enters standby mode after 3 minutes of inactivity
to conserve power. Press any control panel button or
switch to resume normal operation.
NOTE: Buttons start flashing 10 seconds after a problem has occurred.

13
PROBLEM PROBABLE CAUSE/SOLUTION
Blender fails to start
and program lights
are not illuminated.
• Make sure that the main power RESET/OFF (I/O) button is
in the RESET (I) position.
• Check to see if unit is securely plugged into an electrical
outlet of the proper voltage and frequency.
• Check to see if the fuse for the electrical outlet has blown
or if a circuit breaker has tripped.
Blender stops while
it is running and the
program lights are
illuminated.
• This blender is equipped with motor overload protection.
If the motor stops during operation due to overheating,
unplug and allow the blender to cool down. Plug blender
back in after 15 minutes.
• Resume normal operation.
Blender stops while
running and START/
STOP () light
flashes.
• Mixture in blender is too heavy of a load on the motor. This
blender is programmed to stop running to protect itself from
electrical damage. Remove some of the ingredients from the
blender jar. Turn VARIABLE SPEED DIAL to 1 and press the
START/STOP () switch to continue to process in MANUAL
mode. Increase speed as necessary. If this issue happens again,
remove more of the blender mixture and start the process again.
Ingredients will not
mix properly.
• Check to see if enough liquid has been added to the
ingredients. Mixture should be fluid and free-running at all
times.
• Solid pieces are too large.
• Container is too full. Do not fill past highest (8 cups/1.9 L)
graduation marking.
• Cutter assembly blades are not sharp or are damaged.
Inspect container and cutter assembly daily.
• Select speed to create a fluid blend.
Blender smells like it
is burning.
• Turn off blender and allow unit to cool.
• Although motors are tested during the manufacturing
process, heavy use may cause curing of motor windings.
The smell may quickly dissipate after a few heavy uses.
• If smell continues after additional heavy uses, call our
customer care center.
There is grease
around the bottom of
the blender jar or on
the counter top.
• Monitor the problem and source. This may indicate an
issue with the jar bearings.
• Call our customer care center if the condition persists.
Blender jar is cloudy
or stained.
• Some cloudiness may be natural after use. The minerals
from fruits, produce, and leafy greens, in addition to the
oils of various nut butters, can sometimes cause a film on
the blender jar or may be difficult to clean.
• Sprinkle 1/4 cup (59 ml) baking soda in blender. Add 1 cup
(237 ml) white vinegar. Mixture will bubble. When bubbling
subsides, add 2 cups (473 ml) water and blend on the HOT
SOUP () cycle. Wash any remaining residue with dish
soap and water. Rinse and dry thoroughly.
Blender fails to start. • Jar is not in place.
Troubleshooting (cont.)

14
重要安全说明
1. 阅读所有相关说明。
2. 本电器不适合以下人群（包括儿童）使
用：行动不便者、精神或智商缺陷者、缺
少经验和常识者，除非他们在监督和指导
下使用，以确保安全。
3. 使用或在儿童附近使用该设备时，一定要
密切监督。请勿将本电器用于儿童玩耍。
4. 为防止触电危险，请勿将电源线、插头、
底座或电机放入水或其他液体中。
5. 当本装置未使用时、安装或拆解部件和清
洁该电器前，请从插座拔下电源。
6. 避免接触正在运动的部件。
7. 在下列情况下，请勿使用设备：电源线或
插头破损、设备出现故障、设备曾跌落或
已经出现任何形式的损坏。所有维修必须
由制造商、维修代理商或同等资质的人员
进行，以避免险情。请致电所提供的客户
服务电话。如果电源软线损坏，为了避免
危险，必须由制造商、其维修部或类似部
门的专业人员更换。
8. 使用非由电器制造商建议或出售的包括搅
拌杯在内的附件，可能导致人身伤害。
9. 请勿户外使用。
10. 请勿将电源线搭置在桌台边缘上或与发热
表面接触，包括炉子。
11. 请勿将电器放置在高温气体或电炉之上或
附近，或放置在加热的烤箱内。
12. 在搅拌或切碎食物时，手和器具请勿置于
搅拌杯中，并且要远离切割刀片，以降低
严重人身伤害或配件损坏（本料理机可能
未配备这些配件）风险。可使用橡胶刮
铲，但仅限于在料理机未运行时使用。
13. 刀片很锋利；排空搅拌杯和清洗时，务必
要小心处理。
14. 请勿使用有任何裂口或裂缝的搅拌杯。
15. 请勿使用有裂口、裂痕或松动的切割刀片
组件。
16. 本机仅在提供的底座上使用，务必在搅拌
杯盖好盖子以后才操作料理机。仅在添加
食材或插入搅拌棒时才能取下加料口盖。
17. 搅拌热液体时，盖紧加料口盖并关闭任
何用于倒出的边盖口。为防止可能的烫
伤：请勿超过搅拌杯的6杯（1420毫升）
液位。搅拌过程中热液体可能会将盖子推
出；因此，应戴上烤箱手套或用厚毛巾进
行保护，用戴手套的手压住盖子的顶部，
保持裸露的皮肤远离盖子，然后开始以最
低速度搅拌。
18. 确保搅拌杯底座的刀片组件安装牢固。如
果转动刀片意外暴露，则可能导致受伤。
19. 请勿让搅拌机在无人看管的情况下运行。
在更换附件或接触运动部件前要关掉电源
开关并断开电源。
20. 在将电源线插入壁装电源插座前，请关闭
设备。拔掉电源线插头前，请将开关转到
OFF（O）位置。然后从壁装电源插座上
拔下插头。
21. 请勿将该装置用于非预期用途。
22. 小心：为了避免由于热熔断器的意外重置
导致的危险，本电器不能在外接定时器或
独立的遥控控制系统的方式下运行。
当使用电器时，应始终遵守基本的安全防范措施，以减少火灾、触电和/或人身伤害的风险，
包括以下内容：
请妥善保管这些说明！

15
其他用户安全信息
本产品建议于家庭使用。
此电器电源线的长度经过设计挑选，以减
少长电源线缠绕或绊倒的危险。倘若需要
更长的电源线，可使用有认证的电源延长
线。电源延长线的额定功率必须等于或大
于此电器的额定功率。电源延长线必须为
接地型的3线电源线。电源延长线使用时需
特别注意，以防将其搭设在工作台或桌台
上，造成儿童扯拉或绊倒他人。
如果切割刀片组件锁住而不能移动，可能
会损坏电机。请勿使用。要了解有关信
息，请拨打免费售后服务电话。
请勿将装有食物或液体的搅拌杯放入冰箱
中。这可能导致切割刀片组件、搅拌杯、
搅拌机损坏及可能的人身伤害。
注意：本机配有电机过热保护。在操作期间如果电机因过热而停止，请拔掉电源插头并让机
器冷却15分钟。然后再插上机器的电源插头以恢复正常操作。

16
部件和功能
重置/关闭（电源）
（I/O）开关
搅拌杯
底座
搅拌杯垫
盖子
加料口盖
搅拌棒
启动/停止
（）开关
首次使用前：拆开多功能高速破壁料理机的包装后，请遵循“清洁您的料理机”中的说明。
切割刀片
组件
脉冲（ ）
开关 程序按钮
变速旋钮

17
部件和功能（续）
重置/关闭（I/O）（电源）开关/断路器：
重置/关闭（I/O）（电源）开关位于搅拌杯底座的右侧。此开关控制料理机
的电源。此开关也用作断路器使用，如果跳闸将关闭机器，复位后重置。
控制面板
加料口盖：制作调料和酱汁时，在料理机运行过程中，可使用加料口盖慢慢地将液体成分加
入到料理机中。
盖子：盖子的设计便于盖上、拿下及清理。在操作电器时，务必使用盖子和加料口盖。
搅拌杯：清楚标示有计量单位。
搅拌棒：搅拌棒有助于混合不适用普通搅拌功能搅拌的浓稠或冷冻材料的食物。它可防止气
泡形成，为果仁酱或冷冻甜点制作的好帮手。
自动过热保护：本机配有电机过热保护。在操作期间如果电机因过热而停止，请拔掉电源插
头并让机器冷却15分钟。然后再插上机器的电源插头以恢复正常操作。
脉冲（ ）开关：
按住脉冲（ ）开关不放，以手动模式中变速旋钮上所设定的速度进行搅
拌。
变速旋钮：
中间的变速旋钮决定料理机在手动模式时的速
度设定。
程序按钮：
有四种程序设置：热汤（ ）、冰沙（ ）、刨冰（ ）和纯果
汁（ ）。按对应的按钮选择所需的程序。
启动/停止（ ）开关：
启动/停止（ ）开关用于开始或停止手动模式，或在某一程序结束前停
止该程序。

18
使用您的料理机
首次使用前：拆开多功能高速破壁料理机的包装后，请遵循“清洁您的料理机”中的说明。
重要提示：
您的搅拌杯和切割刀片组件在正常使用过程中可能会磨损。请务必检查搅拌杯是否
有裂纹、缺口或裂缝。请务必检查切割刀片组件是否有破损、破裂或松动。如果搅拌杯或切割
刀片组件损坏，请勿使用。
1 2
3 4
插上料理机插头。将重置/关闭（I/O）开关
调到重置（I）位置开启料理机，并准备进
行搅拌。正面的指示灯点亮。在机器处于
无人看管状态时，将重置/关闭（I/O）开关
调到关闭（O）位置。如果料理机已经插上
电源并且开关位于开启（I）位置，但面板
指示灯不点亮，表明料理机已进入待机模
式。3分钟内无任何操作将出现这种情况。
按控制面板上的任意按钮或旋转开关以恢复
正常操作。
将搅拌杯放置到底座上。 添加食材。
盖上搅拌杯盖子和加料口盖。将加料口盖
插入到搅拌杯盖中并顺时针旋转固定。取
下加料口盖，以使用搅拌棒或添加食材。

19
热汤（ ）
设置可制作浓汤，并
将浓汤加热至接近
沸点的温度。此程序
搅拌量不得超过6杯
（1420毫升）。制作
汤时，食材请从低温
或室温开始搅拌。加
料口盖可以保持在盖
子上。料理机运行5分45秒。
冰沙（ ）
设置搅拌冰冻或新鲜
冰沙。料理机首先脉
冲运行五次，将冰或
冰冻原料削碎，然后
变换为高速运行45
秒。
刨冰（ ）
设置将冰块粉碎，用
于制作糖浆饮料或精
美鸡尾酒。料理机从
低脉冲执行至中脉
冲，时长为1分钟。
如果食谱需要制作果
汁或蔬菜汁，请运行
纯果汁（ ）程序。
纯果汁设置可实现对
水果泥或蔬菜泥的均
匀搅拌，将全谷物或
种籽加入果汁后，会
令成品看起来十分精
细。多纤维水果及蔬
菜因此得以打成美味健康的果蔬汁。料理机
从低到高慢慢加速，运行55秒。
使用程序设置
程序将各种不同搅拌速度和持续时间的配方进行优化。按下一个程序按钮仅
所选程序指示灯点亮。当按下程序按钮后，料理机自动开始工作，程序结束
后，料理机自动停止工作。要在程序循环前停止料理机，请按启动/停止
（）按钮。再次按程序按钮，将会重置程序，程序将从头开始执行。
如果您再次按启动/停止（ ）按钮，料理机将默认为手动模式运行。

20
使用手动模式
按启动/停止（ ）按钮，在搅拌期间慢
慢向左或向后旋转变速旋钮增加或降低搅
拌速度。
如果使用脉冲（ ）开关，仅在按下脉冲
（）开关时，料理机才会将以旋钮上所指
示的速度运行。
2
警告 烫伤危险：
倒入搅拌杯
中的热水量不得超过6杯（1420毫升）刻度
线。戴上烤箱手套或用厚毛巾进行保护，用
戴手套的手压住盖子的顶部。让暴露的皮肤
远离盖子。以最低速度开始搅拌。
3 – 可选
1
取下加料口盖并把搅拌棒插入盖孔中。将
加料口盖从上锁位置逆时针旋转至解锁位
置并将其提出。
注意：取下加料口盖并插入搅拌棒前，请
将料理机开关调整到关闭（O）位置。
4 – 可选
旋转变速旋钮到位置1。