Hamilton Beach 2312c User manual

INTRODUCTION TO YOUR NEW HAMILTON BEACH
WATER DISPENSER (model 2312c)
Congratulations, you have acquired a high quality Hamilton BeachWater Dispenser for
bottled water. This unit is packed with many extra features that you will find convenient to use.
Multi-temperature capability allows you to enjoy a cool drink, hot beverage or simply cook your
meals. It will provide you with many years of trouble free use if you follow the safety
precautions and operating instructions provided in this easy-to-use manual. Please take the time
to read it, and save these instructions for future use. Please also remember to record the model
and series code. They are on a label in back of the unit.
_________________ ___________________ __________________
Model number Series code Date of purchase
READ ALL INSTRUCTIONS BEFORE USING!
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should be followed, including the
following:
• WARNING: BURN HAZARD. The
dispenser heats water to a temperature of
approximately 190°F (88°C). Water
temperatures above 125°F (52°C) can
cause severe burns or death from
scalding. Children, the disabled and the
elderly are at highest risk of being
scalded. Children should be supervised by
an adult when using this product.
• WARNING: CRUSH AND FALL
HAZARD. Do not allow children to
climb, stand or hang on the outside of the
dispenser, or on the shelves inside the
storage cabinet. They could tip the
dispenser over or fall and seriously
injure themselves. Children should be
supervised by an adult when using this
product.
• WARNING: FIRE HAZARD. Do not
store or use gasoline or other flammable
vapors and liquids in the vicinity of this
or any other appliance. Do not operate
dispenser with a damaged cord. Do not
use with an underrated extension cord.
• WARNING: SHOCK HAZARD. Unplug
the water dispenser before cleaning or
wiping up spilled water on unit. Do not
attempt to service the dispenser. Do not
operate dispenser with a damaged cord.
• WARNING: TOXIC SUBSTANCE
HAZARD. Do not use with water that is
microbiologically unsafe or of unknown
quality. Do not dispense anything other
than water of known quality.
• CAUTION: SPOILED FOOD HAZARD.
The storage compartment in this unit is
not a refrigerator. Do not store
perishable food in compartment.
1

DANGER: CHILD ENTRAPMENT HAZARD.
PROPERLY DISPOSE OF THE WATER DISPENSER AS
DIRECTED BELOW.
Child entrapment and suffocation are not
problems of the past. Junked or abandoned
dispensers with storage areas are still
dangerous…even if they will sit for “just a
few days.” If you are getting rid of your old
water dispenser, please follow these
instructions to help prevent accidents.
BEFORE YOU THROW AWAY YOUR
OLD DISPENSER:
• Take off the doors and discard
separately.
• Leave the shelves in place so that
children may not easily climb inside.
• If the dispenser door has a lock, make it
unusable.
REFRIGERANT DISPOSAL:
Your old water dispenser may have used a
regulated refrigerant in its cooling system.
These refrigerants are believed to harm
stratospheric ozone. If you are throwing
away your old dispenser, make sure the
refrigerant is removed and recovered for
proper disposal by an EPA-certified
technician. If you intentionally release this
refrigerant, you can be subject to fines and
imprisonment under provisions of
environmental legislation.
SAVE THESE INSTRUCTIONS!
2

PROPER INSTALLATION AND LOCATION
1) Dispenser is for indoor use only. Do
not use outdoors.
2) To prevent algae growth, find a
location for your dispenser that is
protected from direct sunlight and
other sources of heat (e.g., radiators,
baseboard heaters, cooking appliances,
etc). Do not use when relative
humidity is greater than 90%.
3) Do not install the dispenser where the
surrounding air temperature will be
above 100°F (38°C) or below 50°F
(10°C).
4) Place the dispenser on a level surface
that can support its weight with a full
water bottle on it.
5) To ensure that your water dispenser
works at the maximum efficiency,
leave at least 2 inches of clearance
between all sides of the dispenser and
any walls.
6) To prevent damage to dispenser, do
not plug dispenser into the power
outlet until reading the instructions
first!
GROUNDING INSTRUCTIONS
WARNING – Improper use of the grounding plug can result in a risk of
electric shock.
• This appliance must be grounded. In the
event of an electrical short circuit,
grounding reduces the risk of electric
shock.
• This appliance is equipped with a power
cord having a grounding wire with a
grounding plug. The plug must be
plugged into an outlet that is properly
installed and grounded.
• Consult a qualified electrician if the
grounding instructions are not completely
understood, or if doubt exists as to
whether the appliance is properly
grounded.
• If the outlet is a standard 2-prong wall
outlet, it is your personal responsibility
and obligation to have
it replaced with a properly grounded 3-
prong wall outlet.
• Do not under any circumstances cut or
remove the third (ground) prong from the
power cord.
• Do not use an adapter plug with this
appliance.
• Do not use an extension cord with this
appliance. If the power cord is too short,
have a qualified electrician install an
outlet near the appliance
• For best operation, plug the appliance
into its own electrical outlet on a
dedicated circuit to prevent flickering
of lights, blowing of fuse, or tripping
of circuit breaker.
3

GETTING FAMILIAR WITH YOUR HAMILTON BEACH
WATER DISPENSER
Features:
• Designed for in home or office use.
• Front panel has three indicator lights, to see if the power, heating and cooling are on.
• Two power switches are located on the back of the dispenser. One is for cooling and one
for heating.
• Designed with distinctive thermal isolation technology, this dispenser can minimize
thermal exchange between hot and cold water.
• Both hot water tank and cooling tank are 304 stainless steel.
• Convenient, built-in, 0.50 cubic foot storage compartment for non-perishable items.
• Chilling compressor is quiet and durable.
• There are two high-flow faucets on the front of the unit. The faucet with the red child-
safety button is for hot water and blue is for cold water.
• Hot water faucet has a child resistant hot water guard. To operate it, push the red tab to
the left to disengage the locking device, then push the push button inward.
• Removable, easy-to-clean drip tray.
• The power cord has a grounded plug. Please make sure that your outlet is properly
grounded.
• Rated power is 420W for heating and 90W for cooling
• Fits 3 or 5 gallon bottles
4

Parts Listing:
5
Part No. Part Name Part No. Shown
on Diagram
Part No. Part Name Part No. Shown
on Diagram
HB-BS-1003 Bottle Supporter 1HB-DT-1012 Drip Tray 9
HB-SE-1004 Separator 2HB-SD-1013 Storage Door 10
HB-CT-1005 Cold Water Tank 2B HB-RS-1014 Removable Shelf 10B
HB-GIL-1006 Green Indicator Light 3HB-HS-1015 Heating Switch 11
HB-RIL-1007 Red Indicator Light 4HB-CS-1016 Cooling Switch 12
HB-BIL-1008 Blue Indicator Light 5HB-TH-1017 Thermostat
(Do not touch)
13
(under panel)
HB-CWF-1009 Cold Water Faucet 6HB-PC-1018 Power Cord 14
HB-HWF-1010 Hot Water Faucet 7HB-DOC-1019 Drain Outlet Cap 15
HB-CAS-1011 Casing 8HB-SS-1020 Silicon Stopper 15B

PREPARING, LOADING & OPERATING YOUR DISPENSER
1) Make sure that the dispenser is not plugged into the electrical outlet and that both the
hot and cold power switches (on the back of the dispenser) are set to the OFF position.
2) Sanitize the dispenser water tanks prior to installing a full bottle of water for the first
time (see “Proper Care and Cleaning of Dispenser”).
3) The water bottle will have a cap. The cap may have a stopper that is intended to be
pushed into the bottle. (Sometimes these stoppers are covered by a removable
paper/foil seal.) If your bottle has a cap with a stopper, simply hold the water bottle
vertically straight upside down and place the water bottle into the support collar on
top of the water dispenser. The post in the collar will push the stopper into the bottle.
If the water bottle cap does not have a stopper that is intended to be pushed into the
bottle, first remove the support collar of the water dispenser by turning it
counterclockwise and pulling it straight up and off. Then remove the cap from the
water bottle. Quickly lift the water bottle, turn it upside down, and place the water
bottle onto the top of the water dispenser. Wipe up any water that spills on to the
water dispenser or floor.
________Rotate counterclockwise
and pull straight off
a. Press the hot and cold dispenser buttons until water runs from all faucets.
NOTICE: To avoid damage to the dispenser, do not plug in the power cord or turn
on the heating switch (red) until water runs freely from the hot water faucet when
the hot water faucet is activated.
b. Plug in the dispenser into a grounded power outlet (see Grounding Instructions).
c. Set the HOT and COLD power switch (located on the rear of the dispenser) to the
ON position. Indicators light up accordingly once the dispenser is functioning.
NOTICE: To prevent damage to dispenser, give the dispenser four hours to warm
up to room temperature before plugging it in if the dispenser is brought in from
outside in the winter time.
4) Allow 30 minutes for water to reach hot and cold temperatures.
5) The hot water temperature is preset to 190 degrees Fahrenheit (88 degrees Celsius).
The HOT dispenser button is equipped with a child safeguard that reduces the risk of
hot water being dispensed accidentally or by small children.
WARNING: BURN HAZARD. The dispenser heats water to a temperature of
approximately 190 ° F (88 ° C). Water temperatures above 125 ° F (52 °C) can
cause severe burns or death from scalding. Children, the disabled and the elderly
6

are at highest risk of being scalded. Children should be supervised by an adult
when using this product.
6) Before the dispenser leaves the factory, the cold water thermostat is properly set. Do
not adjust the thermostat.
7) When bottle is empty, vertically pull it out by two hands, then replace it with another
bottle.
8) The spilled water in the drip tray must be removed regularly and cleaned properly. To
remove it, slide tray out.
________ Drip Tray Grille
________Drip Tray
9) In case hot or cold water is not needed for an extended period of time, turn off the
switch accordingly to save power.
NOTICE: To prevent damage to dispenser, do not turn cold water switch back on
within 3 minutes of having turned it off.
PROPER CARE AND CLEANING OF DISPENSER_____________________
WARNING: SHOCK HAZARD. Unplug the water dispenser before cleaning.
Cleaning the Outside and Storage Compartment:
IMPORTANT: Set both power switches (on the back of the dispenser) to the OFF position and
unplug the water dispenser before cleaning.
The inside and outside of the cabinet can be washed with mild soap and water. Rinse thoroughly
with clear water. Never use commercial cleaners or abrasive scouring powders.
Sweep away or vacuum any dust from the condenser coils on the back of the unit. For best results,
use a brush specially designed for this purpose. It is available at most appliance stores.
Cleaning the Inside of the Storage Compartment:
For prevention of odor, place an open box of baking soda in the storage compartment.
IMPORTANT: Set both power switches (on the back of the dispenser) to the OFF position and
unplug the water dispenser before cleaning.
Use a solution of warm water and baking soda (approximately one tablespoon of baking soda to
one quart of water). This will clean and neutralize odors. Then rinse and wipe dry.
7

Other parts of the storage compartment including door gaskets and plastic parts can be cleaned in
the same manner.
NOTICE: To prevent damage to the water dispenser, the plastic storage parts are not to be
washed in the dishwasher.
Draining Instruction:
The dispenser should be drained before cleaning the tanks and before leaving for long vacations or
absences.
1) Set both power switches (on the back of the dispenser) to the OFF position and unplug
the dispenser.
2) Dispense water from both buttons into container(s) until no more water can be
dispensed (about 1 quart of water still remains in the dispenser). Put a container that
will withstand hot water under the hot water faucet.
3) Remove the water bottle from the dispenser.
4) Place a large bucket beneath the drain outlet on the rear of the dispenser.
5) Using a Phillips screwdriver, loosen the screws on the bracket covering the drain outlet
cap. Rotate the bracket out of the way to allow access to the cap.
6) Remove the cap and silicon stopper from the drain outlet and allow water to drain.
8

WARNING: BURN HAZARD. The dispenser heats water to a temperature of
approximately 190 ° F(88 ° C). Water temperatures above 125 ° F (52 °C) can
cause severe burns or death from scalding. Children, the disabled and the elderly
are at highest risk of being scalded. Children should be supervised by an adult
when using this product.
After draining, replace the silicon stopper and cap.
7) Rotate the bracket back into place and tighten screws.
8) Make sure to install a full bottle and dispense water from both water faucets before
plugging in and turning on the dispenser (see Preparing, Loading and Operating Your
Dispenser).
Cleaning the Drip Tray and Grill:
The drip tray is not self-draining. To reduce water spotting or deposits, the tray and its grill should
be emptied, cleaned and wiped dry regularly. Clean with mild soap or on the top rack in the
dishwasher.
Cleaning the Separator:
1) IMPORTANT: Set both power switches (on the back of the dispenser) to the OFF
position and unplug the water dispenser before cleaning.
2) Remove the water bottle and drain the dispenser (see Draining Instruction).
3) Remove the support collar by turning counterclockwise and pulling straight off.
________Rotate counterclockwise
and pull straight off
9

4) Remove the plastic separator by pulling straight out (you may need to twist slightly to
loosen).
5) Clean the separator with dish soap and water or in the top rack of the dishwasher.
6) Dry the separator thoroughly on both sides.
7) Using a clean cloth or paper towel, thoroughly dry the cold water reservoir.
8) Place the separator back in the dispenser. Make sure the long, tapered end of the separator
is positioned firmly on the metal plug on the bottom of the reservoir.
9) Replace the support collar and turn clockwise until it is firmly in place.
10) Install a full water bottle on the dispenser (see Preparing and Loading Your Dispenser for
Use).
Sanitizing and Cleaning the Water Tanks:
Important: Periodically the water dispenser tanks must be sanitized to prevent unpleasant tastes in
the water and cleaned to remove mineral deposits that can impair flow.
To Sanitize:
Important: Before cleaning, set both power switches (on the back of the dispenser) to the OFF
position and unplug the water dispenser. Note: For first time installation, skip next three steps.
1) Empty the water bottle, then remove it from the dispenser.
2) Drain the water tanks (see Draining Instructions).
3) Reinstall the silicon stopper and drain cap (see Draining Instructions).
10

4) DO NOT ADD BLEACH FIRST OR DIRECTLY TO THE DISPENSER.
Concentrated bleach may damage plastic.
5) Add ½ teaspoon (2.5 ml) of ordinary 6.0% maximum household bleach to a 2 quart (2 liter)
pitcher filled with tap water.
6) Pour the solution in the opening at the top of the dispenser.
7) Repeat last two steps until the dispenser is full.
8) Press the hot and cold dispenser buttons until the water just begins to flow from the faucets.
9) Allow to sit for 15-20 minutes.
10) Rinse out the bleach solution.
11) Drain the water tanks into a large bucket (see Draining Instruction).
12) Make sure that the silicon stopper is NOT installed.
13) IMPORTANT: Remove the separator and wipe out the cold water reservoir
(see Cleaning the Separator).
14) Clean, then reinstall the separator and collar (see Cleaning the Separator).
15) Pour approximately 1 gallon (4 quarts or 4 liters) of fresh tap water into the top and allow
to drain into the bucket.
16) Flush with an additional 1 gallon (4 quarts or 4 liters) of fresh tap water and allow to drain
into the bucket.
17) Reinstall the silicon stopper and drain cap (see Draining Instructions).
18) Install a fresh water bottle (see Preparing and Loading Your Dispenser for Use).
19) Dispense 1 quart (1 liter) of water from each faucet and taste to make sure the bleach
solution is completely removed.
20) If you continue to taste the chlorine from the bleach solution, repeat steps 11 – 20 until the
taste is gone.
21) Plug in the dispenser. Then turn on the hot and cold power switches (on the back of the
dispenser).
11

To Remove Mineral Deposits:
Mix 2 quarts (2 liters) of water with two quarts of vinegar OR mix 1 gallon of water (4 liters) with
16 ounces (454 g) of citric acid crystals. Bleach does not remove mineral deposits. Do this in
place of step 6 above when removing mineral deposits.
Preparing for Vacation:
For long vacations or absences, set both power switches (on back of the dispenser) to the OFF
position.
Unplug the water dispenser.
Remove the water bottle.
Drain the water tanks (see Draining Instructions)
Dry the separator thoroughly on both the top and bottom (see Cleaning the Separator).
After returning from vacation, make sure to sanitize the water tanks before using the dispenser (see
Sanitizing and Cleaning the Water Tank).
TROUBLE SHOOTING_____________________________________________
PROBLEM POSSIBLE CAUSES SOLUTION
No hot or cold water 1. over consumption of hot or 1. wait 30 minutes
cold water in short period before using again
of time
2. no power supply 2. connect plug to socket,
turnonheatingor
coolingswitch.
Water is not cool Dispenser is unplugged Push plug completely into
outlet
Cooling switch not on Check to be sure cooling
switchisturnedtoON
The fuse is blown/circuit Replace house fuse or reset
breaker is tripped circuit breaker.
Iftoomanyitemsare
plugged into a single
circuit,movesomeitems
toadifferentcircuit
12

Temperature limiter tripped Set the hot and cold power
switchestoOFF position.
Waitfiveminutes,thenset
switchestoON position.
Wait30minutesforwater
toheatorcool.
Water is not hot Dispenser is unplugged Push plug completely into
outlet
Heating switch not on Check to be sure heating
switchisturnedtoON
The fuse is blown/circuit Replace house fuse or reset
breaker is tripped circuit breaker.
Iftoomanyitemsare
plugged into a single
circuit,movesomeitems
toadifferentcircuit
Temperature limiter tripped Set the hot and cold power
switchestoOFF position.
Waitfiveminutes,thenset
switchestoON position.
Wait30minutesforwater
toheatorcool.
PROBLEM POSSIBLE CAUSES SOLUTION
No water running 1. empty bottle 1. replace with new bottle
out from faucets 2. inlet of bottle supporter 2. clean out wasted paper
blocked by bottle seal and bottle seal, install
bottle again
Water dispenser does 1. empty water bottle 1. replace with new bottle
not work 2. mineral deposits clogging tank 2. see Care and Cleaning.
Water dispenser leaks crack or pin hole in bottle replace with new bottle
from the outside
Compressor runs too 1. room temperature is hotter This may be necessary to
frequently than normal maintain a constant
temperature during hot
andhumiddays
2. dispenser does not have Check to be sure unit is
proper clearance properly located to ensure
adequateairflow
Noisy operation improper installation place the machine on level
surface
13

Bottle making a gurgling noise this is normal
Hot water boiling sound this is normal
Dispenser or water bottle this is normal
shakes when the cooling
system cycles off
Particles floating in Water has high mineral find a water source with
Water content lower hardness
Water in bottle is hot Water is boiling in the hot press the hot dispenser
tank and bubbling up into button until water flows to
the bottle remove air from the hot tank
Foul odor in air around Hot water tank is empty or press the hot dispenser
dispenser not completely full button until water flows to
removeairfromthehottank
Water has poor taste Separator needs cleaning See Cleaning the Separator
or odor
Unit needs to be sanitized See Cleaning and Sanitizing
theWaterTanks.
14

Consumer Support__________________________________________________
Questions? How to contact us: Telephone [phone] (Monday – Friday 8:00AM-5:00 PM ET)
E-mail: [email protected]
[email protected]
15

LIMITED 1-YEAR WARRANTY
What does this warranty cover?
- Any defect in materials or workmanship in the manufactured
product
What does this warranty not cover?
- Water Bottles
- Service trips to your home to teach you how to use the
product.
- Improper installation.
- Failure of the product if it is abused, misused, altered or
used for other than the intended purpose.
- Products that are used outside a residential or office
envinronment.
- Replacement of house fuses or resetting of circuit
breakers.
- Use of this product where water is microbiologically
unsafe or of unknown quality.
- Damage to the product if used to dispense anything other
than water.
- Damage to the product caused by accident, fire, floods or
acts of God.
- Any service to the product
-Incidental or consequential damage caused by possible
defects with this appliance, its installation or repair.
For how long after the original purchase?
- One (1) year.
How do I make a warranty claim?
- Return to the retailer from which it was purchased, along with a
copy of the store receipt within the given period of time allowed
for returns by the retailer (i.e. 90 days). After this period of time,
contact TTI Appliances at 1 800 579 7990. A refund will be
provided once the defective unit and a copy of the receipt has been
shipped to and received by TTI Appliances. This warranty
excludes any cost of shipping to or from TTI Appliances.
How does state law relate to this warranty?
- This warranty is extended to the original purchaser and
any succeeding owner for products purchased for home
or office use within the USA. Some states do not allow
the exclusion or limitation of incidental or
consequential damages. This warranty gives you
specific legal rights, and you may also have other
rights which vary from state to state. To know what
your legal rights are, consult your local or state
consumer affairs office or your state’s Attorney
General.
Exclusion of implied warranties: Except where prohibited or
restricted by law, there are no warranties, whether express,
oral or statutory which extend beyond the description on the
face hereof, including specifically the implied warranties of
merchantability or fitness for a particular purpose.
Warrantor: TTI Appliances, Los Angeles, CA 90025
------------------------------------------------------------------------------------------------------------------------------------------------------------
16