Hamilton/Buhl SWB-80 User manual

Instruction Sheet
Model #: SWB-80
Warranty begins the date item ships from our warehouse. All products, except for metal carts,
have a one year warranty from original date of shipment, unless otherwise noted. Metal carts
have a limited lifetime warranty on all housing components; however, carts have a one year
warranty on any electrical/mechanical components.
Note: This unit is easier to assemble with two people.
Parts list
Qty. Description
1 Top shelf with decal
1 Middle shelf
1 Bottom shelf
2 Side panel
1 Rear panel
1 Left door assembly
1 Right door assembly
2 Leg (Labeled "X")
2 Leg (Labeled "O")
2 Upper pole
2 Lower pole
2 Horizontal mount
2 Vertical mount
Qty. Description
2 Handle shelf
2 Caster with brake
2 Caster without brake
1 Power cord
1 Electrical bracket
3 Set Screw and serrated nut (E)
12 Set Hex head screw & washer for the caster (F)
2 Security screw for top horizontal mount (G)
2 Screw for bottom horizontal mount (H)
25 Set Square head bolt, washer and hex nut (I)
8 Set Hex head screw & washer for fixing handle shelf (J)
8 Set Hex head screw & washer for the handle (K)
8 Philip head screw for the handle shelf (L)
2 Set Screw for fixing the support pole (M)
17 Set Machine screw and washer (N)
4 5 mm screw for TV set (See Screw table M5)
8 6 mm screw for TV set (See Screw table M6)
4 8 mm screw for TV set (See Screw table M8)
4 10 mm screw for TV set (See Screw table M10)
Tools required
Hex wrench
L key (provided)
Adjustable wrench/pliers
Rubber mallet
WARNING: Please keep
the TV mounting screws
M5, M6, M8 & M10 and the
L key in a secure location
as they may be required
for use with the flat panel
TV at a later time.
Handle rail
Handle bar
Handle support bar
Handle shelf
Shelf
Page 1
( Instructions continued on next page )
Screw table
Some screws may have already
screwed on the related parts.
N
M
(On the bottom horizontal mount)
(On the top horizontal mount)
I
H
L
G
M10x16
M8x16
M6x12
K
M5x12
M5x10
M8
M6
M5
M10
(On the handle rail)
(On the lower pole)
(On the legs)
(On the handle bar & handle support bar)
PROP 65 WARNING: This product
contains the chemical known to the
State of California to cause cancer
and birth defects or other reproductive
harm.
!
Horizontal mount
Upper pole Vertical mount
Lower pole

Page 2
10.
Hand-tighten the upper
poles (with holes) to the
lower poles.
1.
Lay front legs (labeled "O" and "X") on the floor with the brackets
facing upward and inward as illustrated. Note: legs,when placed
on the floor should bend upward, off the floor at their top end and
the width of the unit should remain constant all the way to the top.
2.
Slide each shelf over the brackets on the legs. The brackets
should be inside the shelves. The largest shelf is the bottom
shelf. The top shelf has logo decal on it.
3.
Slide the two remaining legs onto the shelves as illustrated. Make
sure that the brackets are inside the shelves.
4.
HAND TIGHTEN the top,
middle and bottom shelves
at the two corners with
square head bolt, washer
and nut (screw table I) as
illustrated. Please make
sure washer and nut are
together on the inside of
the leg bracket.
5.
In order to have the unit properly
aligned, stand unit upright on a
level surface. Gently rock unit
back and forth to realign and
level the unit. TIGHTEN ALL
NUTS AND BOLTS WITH
WRENCHES AT THIS TIME.
Unit should now be properly
aligned and level. If unit is not
level at this time, repeat the
above steps before proceeding
to step 6.
7.
Lay unit on the floor. Align the holes on the
casters with the holes on the corner of the
bottom shelf. Use the hex screws
(see Screw table F) and tighten
the caster. Repeat the same
for the other three casters.
It is recommended you
place the locking casters
on either the right side
or left side of the unit
for safer and easier
movement of cart
through doorways, ect..
( Instructions continued on next page )
Top
Bottom
Leg"O"
Leg"X"
Top Middle
Bottom
Leg"O"
Leg"X"
Back of shelf
Front of shelf
Leg "X"
Leg "O"
6.
Slide the rear panel between the
middle and bottom shelf. The
bottom of the rear panel
needs to hook onto the
bottom shelf frame lip
and the top of the rear
panel needs to go in
between middle shelf lip
and the brackets.The
side panels Assembly
as same as above steps.
8.
To secure the cabinet panel, use the machine screws (see screw
table N) to tighten the cabinet panels to the frame poles as shown.
There are two screws on each side.
9.
Install the two doors onto the frame with two machine screws
(see screw table N) on each side. Do not tighten completely
at this time. Adjust the doors to make sure they close and lock
OK. Tighten all screws.
Upper pole
Lower pole

Page 3
11.
Insert the two supporting
poles onto the holes of top
and middle shelves as
shown.
12.
Insert the two horizontal
mounts onto the supporting
poles. Note: The mount with
adjustable screw(see screw
table H) should go on the
bottom. Screw(see screw
table G) the top mount to
desired height from A to F.
Adjust the bottom mount
height according to the TV
screw position as shown.
Top horizontal mount
Bottom horizontal mount
Handle Rail
Handle support bar
Handle bar
Shelf
14.
Handle shelf assembly
Unscrew the screws from
handle bar, handle
support bar and handle
rail (see screw table K&L).
Align the holes on the
handle rail with handle bar,
handle support bar and
shelf, tighten the screws
as shown.
16.
Electrical bracket assembly instruction
A. Push power cord onto
cord winder bracket.
B. Attach electrical
bracket to back side
of top shelf with two
nuts and bolts (see
screw table E).
Tighten nuts and
bolts securely.
Wrap power cord
around wings of
the bracket.
13.
Tighten the two
supporting poles
onto the bottom
shelf with two
screws as shown
(see screw table M).
15.
Unscrew the screws
from the legs (see
screw table J). Align
the holes on the
bracket of the handle
shelf with the holes
on the cart, tighten
the screws.
17.
Use the appropriate screws needed (M5, M6, M8 or M10, see
screw table M5,M6,M8 or M10) to fasten the flat panel TV onto the
vertical mounts as shown.
18.
Hook the vertical mount onto the top horizontal mount. Align the nut
on the vertical mount with the top horizontal mount slot, fasten the
vertical mount with screw M6 (see screw table M6) onto the top
horizontal mount as shown. Align the bottom horizontal mount slot
with one of the 3 nuts on the vertical mount. Use screw M6 (see
screw table M6) to fasten the vertical mount to the bottom horizontal
mount as shown.
Electrical
bracket
Bolts
Rear view
If any parts or hardware are missing or damaged, Do Not
Return the unit to your dealer. Call the HamiltonBuhl
help line at [phone] for immediate parts replacement.
A Division of Vcom MM Corp.
80 Little Falls Road, Fairfield, NJ 07004, USA
1-800-631-0868 • www.HamiltonBuhl.com