HAMPTON BAY 213-532 User manual

INSTRUCTIONS MANUAL
EXTERIOR WALL LANTERN WITH
MOTION SENSOR AND DUSK-TO-DAWN
HOME DEPOT SKU# 213-532 (UPC# 046335852167)
Page 1

Page 2
FEATURES:
Before returning to your local Home Depot, please call our Customer Service Team at 1-877-
527-0313 or visit www.homedepot.com. Please reference your SKU (213-532) or UPC
(046335852167).
QUESTIONS, PROBLEMS, MISSING PARTS:
1. Easy to install.
2. Handsome oil rubbed bronze finish.
3. MOTION SENSOR FUNCTION –At dusk the motion sensor will activate and
automatically turn the light on when moving heat sources (such as people or motor
vehicles) are detected within its coverage area.The motion sensor will remain active
throughout the night and deactivate at dawn. The motion sensor has a detection range up
to 30 feet and a detection angle of 220º.
4. DUSK-TO-DAWN FUNCTION –At dusk the light will automatically turn on. The light
will remain on throughout the night and turn off at dawn. The light will remain off
throughout the day, until dusk.
5. MANUAL OVERRIDE –The user may manually turn on the light from inside his home
using its wall switch.
6. International Dark-Sky Association (IDA) approved fixture.
Thank you for purchasing this Hampton Bay exterior wall lantern. This product has been
manufactured with the highest standards of safety and quality. The finish of this lantern is
weather resistant but over time will naturally weather and fade. This fixture is equipped with
motion sensor and Dusk-to-Dawn features, providing convenience and security against
unwanted criminal element.

Page 3
TOOLS REQUIRED FOR INSTALLATION AND ASSEMBLY (not
included):
CAUTION:
1. Before starting installation of this fixture or removal of a previous fixture, disconnect the
power by turning off the circuit breaker or by removing the fuse at the fuse box.
2. There are no serviceable parts inside the motion sensor. DO NOT try to repair or
disassemble the unit. Doing so could damage the unit and cause possible electrical shock.
Consult a qualified electrician if needed.
3. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL
QUESTIONS. If you have any non-electrical questions about this fixture, please call our
Customer Service Team at 1-877-527-0313 or visit www.homedepot.com. Please
reference your SKU (213-532) or UPC (046335852167).
4. KEEP your receipt and these Instructions for Proof of Purchase.
Safety
goggles
Wire
strippers
Phillips
screwdriver
Electrical
tape
Wire
cutters
Silicon Rubber
Sealant
for exterior use
Flathead
screwdriver
Light Bulb (100
watt maximum)

When selecting a location, be aware of the motion sensor’s maximum range of
30 ft and 220º detection angle.
SELECTING AN INSTALLATION LOCATION:
Select locations away from heat sources, such as heating vents, air
conditioners, and heated swimming pools.
When selecting a location, be aware that the motion sensor is more sensitive to
movement across its coverage area and less sensitive to movement toward or
away from the motion sensor.
Select locations away from nighttime light sources, such as street lamps or
other light fixtures. They may shine light onto photocell sensor (located at the
bottom of the back plate, between the two switches). This light might cause
the photocell sensor to “think” that it is daytime and not allow the light to turn
on during the nighttime.
Be aware that shade from a porch or an eave may not allow enough daylight to
shine onto the photocell sensor and may cause it to “think” that it is nighttime,
and subsequently cause the light to remain on during the daytime.
Page 4

PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):
1 ea Spacer (#19)
1 ea Main Fixture Body (#1)
1 ea Socket Ring (#5)
ASSEMBLY INSTRUCTIONS:
1. Carefully unpack the fixture. Lay out all parts on a clean surface.
2. Slide the Shade (#18) onto the Socket (#17). Slide the Spacer (#19) onto the
Socket (#17). Thread the Socket Ring (#20) onto the Socket (#17) to secure
the Shade (#18) in place.
3. Install up to a 100 watt Light Bulb (#2) or a Listed SBCFL (Self-Ballasted
Compact Fluorescent Lamp [not provided]) in the socket of the Main Fixture
Body (#1). Do not exceed a 100 watt incandescent light bulb, or a 26 watt
SBCFL.
1 ea Shade (#18)
Page 5

ASSEMBLY:
1. Main Fixture Body
17. Socket
18. Shade
19. Spacer
20. Socket Ring
2. Light Bulb
Page 6

INSTALLATION INSTRUCTIONS:
PARTS INCLUDED FOR INSTALLATION (parts are not to scale):
Page 7
3 ea Wire
Nuts (#14)
2 ea Bracket Mounting
Screws (#8)
1. Thread the Fixture Mounting Screws (#6) into the provided holes of the Mounting Bracket (#7) as shown. Thread
the Hex Nuts (#9) onto the Fixture Mounting Screws (#6), as shown. Do not tighten the Hex Nuts (#9) at this time.
2. Pull the power supply wires out from the Outlet Box (#4), and mount the Mounting Bracket (#7) to the Outlet Box
(#4), using the Bracket Mounting Screws (#8).
3. Attach the Black Supply Wire (#5) to the Black Fixture Wire (#12) and the White Supply Wire (#16) to the White
Fixture Wire (#13) using Wire Nuts (#14). Connect the Fixture Ground Wire (#11) and the Supply Ground Wire
(#15) together using a Wire Nut (#14). Wrap all wire connections with electrical tape for a more secure connection.
Note: If you have electrical questions, consult your local electricalcode for approved grounding methods.
4. Place the Wall Plate (#10) over the Outlet Box (#4) and onto the Fixture Mounting Screws (#6), and adjust the
Fixture Mounting Screws (#6) until they protrude out from the Wall Plate (#10) 1/4". Remove the Wall Plate (#10)
and secure the position of the Fixture Mounting Screws (#6) by tightening the Hex Nuts (#9) against the Mounting
Bracket (#7). Place the Wall Plate (#10) back onto the Fixture Mounting Screws (#6), and secure it into place using
the Lock Nuts (#3) provided.
5. After installing the fixture, caulk the upper 2/3s of the Wall Plate (#10) to mounting surface. Leave the bottom 1/3
un-caulked for drainage of any water that might leak into the enclosure. The manufacturer recommends a non-
drying exterior caulking material. A good example is a clear silicone rubber sealant for exterior use.
6. Installation is complete. Turn on power at the circuit breaker or fuse box. Turn the light switch on to activate the
fixture.
1 ea Mounting
Bracket (#7)
2 ea Fixture Mounting
Screws (#6)
2 ea Hex
Nuts (#9)
2 ea Lock
Nuts (#3)

INSTALLATION:
10. Wall Plate
3. Lock
Nut
13. White
Fixture Wire
11. Fixture
Ground
Wire
14. Wire
Nut
16. White
Supply Wire
6. Fixture
Mounting
Screw
15. Supply
Ground
Wire
4. Outlet
Box
7. Mounting
Bracket
8. Bracket
Mounting
Screw
9. Hex
Nut
12. Black
Fixture Wire
Page 8
5. Black
Supply
Wire

OPERATION INSTRUCTIONS:
SETTING MOTION SENSOR SENSITIVITY IN TEST MODE: (Note: Sensitivity directly correlates to
the sensor’s detection range.) In TEST mode, slide the “SENSITIVITY” switch to a desired level: “L” for
low, “M” for medium, or “H” for high. From a distance, walk through the coverage area. When the sensor
detects you and the light turns on, note your distance from the fixture. Move away from the fixture and wait
4 to 5 seconds for the light to turn off. Walk through the coverage area again, this time trying a different
approach toward the fixture at different angle. Again, make note of your distance from the fixture when the
light turns on. Repeat these steps, approaching the fixtures down different pathways. Especially, walk
through pathways where you expect high traffic, such as walkways and driveways. After testing various
pathways, decide to increase or decrease the detection range, or to keep it the same. To increase the
detection range, slide the “SENSITIVITY” switch to the next highest level. To decrease the detection range,
slide the “SENSITIVITY” switch to next lowest level. Repeat the steps above. Continue to adjust the
sensitivity level until optimum results are attained.
SELECTING FUNCTION: After setting the sensitivity to the desired level, select the function by sliding to
“TIMER” switch to one of the following positions:
GETTING STARTED: After installing the fixture, slide the “TIMER” switch to “TEST”.Restore power at
the circuit breaker and turn on your wall switch (if applicable). The light will turn on and remain on for
approximately 45 seconds. Then the light will flash 3 times and then turn off. (Note: TEST mode allows you
to conveniently set the motion sensor sensitivity. In TEST mode, the motion sensor will turn on the light
when it senses movement. Four to five seconds after movement has stopped, the light will turn off.)
"TIMER"
Switch
Position
Function Description
2
6
DUSK-TO-
DAWN
Dusk-to-
Dawn
At dusk, the light will turn on. The light will remain on throughout the night
until dawn. At dawn, the light will turn off. The light will remain off
throughout the day until dusk.
Motion
Sensor
At dusk, the motion sensor becomes active. Any movement within the
coverage area will cause the light to turn on. After movement has stopped,
the light will remain on for the preset time limit of2or6 minutes, at which time
the light will turn off. The motion sensor will remain active throughout the
night. At dawn, the motion sensor will deactivate. The motion sensor will
remain deactivated throughout the day. Movement will not cause the light to
turn on.
Page 9
NOTE: To make sure the above functions operate properly, always keep the wall switch in the “ON” position
(including daytime).

Page 10
OPERATION INSTRUCTIONS (CONT):
Flip wall switch
OFF-ON-OFF-ON
within 3 seconds
Motion Sensing
Mode (light off)
Manual Override
Mode (light on)
MANUALOVERRIDE:
You may manually turn on the light from inside your home using the wall switch that controls your light
fixture. This feature may be used during nighttime when the light is off, while the circuit is in the Motion
Sensing Mode. To manually turn on the light and activate the Manual Override, quickly flip your wall
switch OFF-ON-OFF-ON within a 3 second span. The light will remain on until the override is deactivated.
To turn off the light and deactivate the Manual Override, flip your wall switch OFF-ON-OFF-ON again.
This will return the circuit back to the Motion Sensing Mode. If you do not deactivate the Manual Override,
the light will remain for 8 hours or until dawn (which ever comes first), at which time the light will turn off
automatically. You may toggle the switch in this manner as many times as you need, to alternate between
the two modes, Manual Override Mode (light on) and Motion Sensing Mode (light off).
This switch toggling
sequence alternates
the circuit between
Manual Override
(light on) Mode and
Motion Sensing
Mode (light off)
Switch in the
“ON” position

Page 11
Problem Possible Cause Corrective Action
1. Power is off.
1. Make sure wall switch and circuit
breaker are on.
2. Faulty switch. 2. Test or replace switch.
3. Faulty wire connection. 3. Check wiring.
4. Light bulb may be dead. Test light bulb in
a workinglight fixture.
4. Replace light bulb
Fuse blows or circuit breaker
trips when light is turned on.
1. Crossed wires or power wire is grounding
out.
1. Check wire connections.
Too much sunlight is shiningonto photocell
sensor in the early evening.
Relocate fixture away from a western
facing wall.
Too much light is shiningonto photocell
sensor due to another light source, such as a
street lamp or other light fixture.
Eliminate or turn off other light
source.
OR
Block other light source from shining
onto photocell sensor.
OR
Relocate fixture.
In motion sensingmode, the
light stays on continuously.
False triggeringcause by a heat source, such
as a heater or dryer vent, or heated
swimmingpool.
Eliminate heat source.
OR
Relocate fixture.
Street or sidewal traffic is triggeringthe
motion sensor.
Lower the sensitivity.
False triggeringcause by a heat source, such
as a heater or dryer vent, or heated
swimmingpool.
Eliminate heat source.
OR
Relocate fixture.
The light comes on duringthe
daytime or too early in the
evening.
The fixture may be installed in a shaded area,
such as under a porch or eave, preventing
daylight from shiningonto the photocell
sensor.
Relocate fixture.
In the Dusk-to-Dawn
function, the light comes on
too late in the evening.
Too much sunlight is shiningonto the
photcell sensor in the early evening.
Relocate fixture away from a western
facing wall.
In the Dusk-to-Dawn
function, the light does not
come on at night.
Too much light is shiningonto the photcell
sensor due to another light source, such as a
street lamp or other light fixture. Cover the
photocell sensor with black electrical tape, to
verify that the light will turn on when there
is enough darkness.
Eliminate or turn off other light
source.
OR
Block other light source from shining
onto photocell sensor.
OR
Relocate fixture.
The light never turn on.
The light does not turn on at
night.
The light comes on for no
apparent reason.
TROUBLESHOOTING:

Page 12
LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a
period of three (3) years from date of purchase. This warranty applies only to the original consumer
purchaser and only to products used in normal use and service. If this product is found to be defective, the
manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of of the product at
the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse,
accident, modifications, alterations, neglect or mishandling. This warranty shall not apply to any product
that is found to have been improperly installed, set-up, or used in any way not in accordance with the
instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of
an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to
faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product,
such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not
warrant and specially disclaims any warranty, whether expressed or implied, of fitness for a particular
purpose, other than the warranty contained herein. The manufacturer specifically disclaims any
liability and shall not be liable for any consequential or incidental loss or damage, including but not
limited to any labor/expense costs involved in the replacement or repair of said product.
PRODUCT MAINTENANCE:
1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a
solvent) to wipe the surface of the fixture.
2. To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker
or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean
water, never a solvent) to wipe the interior surface of the fixture.
3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft cloth to dust or
wipe carefully.

MANUAL DE INSTRUCCIONES
HOME DEPOT SKU# 213-532 (UPC# 046335852167)
Page 13
FAROL DE PARED PARA EXTERIORES CON
SENSOR DE MOVIMIENTO E ILUMINACIÓN
NOCTURNA

CARACTERÍSTICAS:
Antes de regresar a su Home Depot, llame a nuestro Equipo de Servicio al Cliente al 1-877-
527-0313 o visite www.homedepot.com. Dé como referencia su SKU (213-532) o UPC
(046335852167).
PREGUNTAS, PROBLEMAS, PARTES FALTANTES:
Gracias por comprar este farol de pared para exteriores de Hampton Bay. Este producto ha
sido fabricado con los estándares de calidad más altos de seguridad y calidad. El acabado de
este farol es resistente al clima, pero con el tiempo se desgastará y decolorará de manera
natural. Este luminario está equipado con funciones de sensor de movimiento e iluminación
nocturna, lo que provee comodidad y seguridad contra elementos criminales no deseados.
Page 14
1. Fácil de instalar.
2. AtractivoAcabado en Bronce Bruñido con Aceite.
3. FUNCIÓN DE SENSOR DE MOVIMIENTO –Al anochecer el sensor se activará y
encenderá la luz automáticamente cuando se detecten fuentes de calor en movimiento
(como gente o vehículos) dentro de su área de cobertura. El sensor de movimiento
permanecerá activo durante la noche y se desactivará al amanecer. El sensor de
movimiento tiene un rango de detección de hasta 30 pies y un ángulo de detección de
180°.
4. FUNCIÓN DE ILUMINACIÓN NOCTURNA –Al anochecer la luz se encenderá de
manera automática. La luz permanecerá encendida durante la noche y se apagará al
amanecer. La luz permanecerá apagada durante el día hasta en anochecer.
5. ENCENDIDO/APAGADO MANUAL –El usuario puede encender/apagar la luz
manualmente desde el interior de la casa con el interruptor de pared.
6. Luminario aprobado por la International Dark-Sky Association (IDA).

HERRAMIENTAS REQUERIDAS PARA LA INSTALACIÓN Y
ELENSAMBLAJE (no incluidas):
PRECAUCIÓN:
1. Antes de iniciar la instalación de este luminario o la remoción de un luminario anterior,
desconecte la energía eléctrica al apagar el disyuntor de circuitos o al quitar el fusible en
la caja de fusibles.
2. El sensor de movimiento no tiene partes en su interior a las que el usuario pueda dar
servicio. NO intente reparar o desarmar la unidad. Hacerlo puede dañar la unidad y causar
una posible descarga eléctrica. Consulte a un electricista calificado si es necesario.
3. CONSULTE A UN ELECTRICISA CALIFICADO SI TIENE DUDAS CON LAS
CONEXIONES ELÉCTRICAS. Si tiene preguntas acerca de este luminario, que no estén
relacionadas con las conexiones eléctricas, llame a nuestro Equipo de Servicio al Cliente
al 1-877-527-0313 o visite www.homedepot.com. Dé como referencia su SKU (213-532)
o UPC (046335852167).
4. CONSERVE su recibo y estas Instrucciones como comprobante de compra.
Gafas de
seguridad
Pelacables
Desarmador
Phillips
Cinta de
aislar
Pinzas para
cables
Sellador de silicón
para uso exterior
Desarmador de
punta plana
Foco (100 vatios
máximo)
Page 15

Cuando elija una lugar, tenga en mente el rango máximo del sensor de
movimiento de 30 pies y el ángulo de detección de 220º.
SELECCIONE EL LUGAR PARA LA INSTALACIÓN:
Elija un lugar lejos de fuentes de calor, como ventilaciones de calefacción,
aires acondicionados y piscinas con caldera.
Cuando elija un lugar, tenga en mente que el sensor de movimiento es más
sensible al movimiento a lo largo de su área de cobertura y menos sensible al
movimiento hacia o lejos del sensor de movimiento.
Elija lugares lejos de fuentes de luz nocturna, como faroles públicos u otros
luminarios, ya que pueden brillar en el sensor de la fotocelda (ubicado en la
base de la placa trasera, entre los dos interruptores). Esto puede causar que el
sensor de la fotocelda “piense” que es de día y no permitirá que la luz se
encienda durante la noche.
Tenga en mente que la sombra de un pórtico o tejado no permita que luz
suficiente llegue al sensor de la fotocelda y cause que “piense” que es de noche
y, de manera subsecuente, que la luz permanezca encendida durante el día.
Page 16

PARTES INCLUIDAS PARA EL ENSAMBLAJE (las partes no se
muestran a escala):
INSTRUCCIONES DE ENSAMBLAJE:
1 Cuerpo principal
del luminario (#1)
Page 17
1 Espaciador
(#19) 1Anillo del portafoco (#5)
1. Desempaque el luminario con cuidado. Coloque todas las superficies
sobre una superficie limpia.
2. Deslice la pantalla (#18) sobre el portafoco (#17). Deslice el
espaciador (#19) sobre el portafoco (#17). Enrosque el anillo del
portafoco (#20) en el portafoco (#17) para garantizar la pantalla (#18)
en su lugar.
3. Instale un foco (#2) (no incluido) en el portafocos del cuerpo principal
del luminario (#1). No exceda de un foco incandescente de 100 vatios.
1 Pantalla (#18)

ENSAMBLAJE:
2. Foco
1. Cuerpo
principal del
luminario
Page 18
17. Portafoco
18. Pantalla
19. Espaciador
20.Anillo del
portafoco

3 Tuercas para cables (#14)
2 Tornillos para
montar la ménsula (#8)
INSTRUCCIONES DE INSTALACIÓN:
PARTES INCLUIDAS PARA LA INSTALACIÓN (las partes no se
muestran a escala):
1. Enrosque los tornillos para montar el luminario (#6) en los agujeros provistos en la ménsula de montaje (#7), como se
muestra. Enrosque las tuercas hexagonales (#9) en los tornillos para montar el luminario (#6), como se muestra. No apriete
las tuercas hexagonales (#9) en este momento.
2. Saque los cables de alimentación de la caja de distribución (#4) y monte la ménsula de montaje (#7) sobre la caja de
distribución (#4), utilizando los tornillos para montar la ménsula (#8).
3. Conecte el cable negro de alimentación (#5) con el cable negro del luminario (#12) y el cable blanco de alimentación (#16)
con el cable blanco del luminario (#13), utilizando las tuercas para cables (#14). Conecte el cable del luminario a tierra (#11)
con el cable de alimentación a tierra (#15), utilizando una tuerca para cables (#14). Envuelva todas las conexiones de los
cables con cinta de aislar para una conexión más segura. Nota: Si tiene dudas con las conexiones eléctricas, consulte el
código eléctrico de su localidad para los métodos aprobados para las conexiones a tierra.
4. Coloque la placa de pared (#10) cobre la caja de distribución (#4) y en los tornillos para montar el luminario (#6) y ajuste los
tornillos para montar el luminario (#6) hasta que sobresalgan ¼” de la palca de pared (#10). Quite la placa de pared (#10) y
asegure la posición de los tornillos para montar el luminario (#6) al apretar las tuercas hexagonales (#9) contra la ménsula de
montaje (#7). Coloque la placa de pared (#10) otra vez sobre los tornillos para montar el luminario (#6) y asegúrela con las
tuercas de seguridad (#8) que se incluyen.
5. Después de haber instalado el luminario, calafatee las 2/3 partes superiores de la placa de pared (#12) en la superficie de
montaje. Deje la 1/3 parte inferior sin calafatear para el drenaje del agua que se pueda filtrar en la carcasa. El fabricante
recomienda un material que no se seque para exteriores. Un buen ejemplo es un sellador de silicón para uso en exteriores.
6. La instalación ha terminado. Encienda la energía eléctrica en el disyuntor de circuitos o la caja de fusibles. Encienda el
interruptor para activar el luminario.
1 Ménsula de
montaje (#7)
2 Tornillos para montar el
luminario (#6)
2 Tuercas hexagonales (#9)
2 Tuercas de seguridad (#3)
Page 19

INSTALACIÓN:
10. Placa de
pared
3. Tuerca de
seguridad
13. Cable
blanco del
luminario
11. Cable
del luminario
a tierra
14. Tuerca
para cables
16. Cable
blanco de
alimentación
5. Cable negro
de alimentación
15. Cable de
alimentación
a tierra
4. Caja de
distribución
7. Ménsula
de montaje
8. Tornillo para
montar la
ménsula
9. Tuerca
hexagonal
6. Tornillo
para montar
el luminario
12. Cable
negro del
luminario
Page 20