Handy Dryers STERILL User manual

USER MANUAL
www.handydryers.co.uk

2
Voltage 240V Motor Brushed motor
Phase Single phase Sensing distance 15–20cm
Power 1400W Protection class IPX1
Air speed 60–105m/s Dimensions 335 x 172 x 410mm
Heating power 800–950W Net weight 5.1kg
•Do not open the front panel – electric shock risk
•Never look directly at the UV bulb when in operation
•Do not allow children or adults to pull or hang on the machine
•Place the unit away from direct water supplies
•A suitably rated fused power supply is required
•Ensure the correct power supply is used, if more than +/-10%
the unit may malfunction
•The power must be turned off during installation and maintenance
•Ensure the unit has a reliable earth connection
•This hand dryer must be installed by a qualied electrician
•If the power cord is damaged it must be replaced by the manufacturer,
its service agent or a qualied person
•A residual current device (RCD) with a rated residual operating current,
not exceeding 30mA is recommended
•Please use dedicated spur
•In case of malfunction, switch off power immediately
•Air lter must be installed
Environmental Protection
•Do not dispose of electrical waste with household waste, please recycle
in appropriate facilities. Check with your Local Authority or retailer for
recycling advice.
WARNING:
INJURY MAY OCCUR IF MISUSED
SPECIFICATIONS
Prohibited
Do not allow
unit to get
excessively wet
Do not
dismantle
Follow
instructions
carefully

3
DO NOT install in the following places
•Where the temperature can be below -10°C or above 40°C
•Where the unit may come into direct contact with excessive water
•If the unit will be in direct or strong sunlight
•If there is a lot of condensation in the environment
•If there are corrosive, neutral or reductive gases present
•20m or more below, or 2000m or higher than, sea level
Installation position
The following diagram shows the recommended position
•Ensure there is at least 150mm clear space below the machine
(either to the oor or other objects in the location)
•It is recommended that a minimum distance of 100mm should
be left clear to either side of the unit
•Avoid locations where people or doors might damage the unit
•Choose a completely at wall surface to mount the unit onto
LOCATION
& PRE-INSTALLATION PRECAUTIONS
Hole of junction box
without shell
241mm 170cm
160cm
81cm
91cm
102cm
112cm
258mm
258mm 240mm
241mm
190mm
Floor
(4-7)
(7-10)
(10-13)
(13-16)

4
Connect the unit to power supply
Embed a backbox in the installation location
(1 switchbox no cover)
•If no backbox is used the power cord may
prevent the unit from sitting ush against
the wall
Remove the outer shell
•Using the Allen key supplied, remove
the 2 countersunk screws from the body
of the unit
•Pull the outer shell upwards gently to remove
Take extra care to avoid scratching the shell
Machine installation
•Fix the unit directly to the wall using screws
supplied
Connections: Live=L, Neutral=N, Earth=
Replace outer shell
•Using the Allen key supplied, tighten
the 2 screws at the sides of the body
LOCATION
& PRE-INSTALLATION PRECAUTIONS
1
2
3
4
Power
supply
cable
1060mm
300mm
UV bulb
casing
Shell
Countersunk
screws
Allen key
Shell
Countersunk
screws
Allen key
Pop out for r
ear
cable access
UV bulb
casing
Connecto
r

5
External maintenance
Clean with a soft cloth. If the unit is very dirty use a soft,
dampened cloth with a neutral cleaning agent, then polish
with a soft, dry cloth
•Only use neutral cleaning agents
•Do not use thinners, acidic or alkaline toilet cleaners
or nylon brushes (they may damage the surface)
•If using chemical cloths, read instructions rst
Bi-annual replacement of UV lamps
NEVER look at the bulbs when in operation
•Ensure unit and power are switched off and
remove the outer shell to access the lamp unit
•Remove lamp unit cover to reveal the dual bulb.
Carefully clear the unit of any dust using a soft brush
•Gently loosen the old lamp by holding the lamp
holder in one hand and pulling the lamp upwards
and away from the lamp holder
•Replace the dual lamp with a new one by
inserting it into the lamp holder and pushing
it downwards until it clicks into position.
Do not touch the new lamp with your bare hands
•Replace the cover
LED indicator lights
•LED lights showing through the top grills slowly fade on and off under normal
operation. If the LEDs change to red, it means the lamp has failed and needs
immediate replacement, the Sterillo will still operate as a normal hand dryer,
however, its sanitisation module will not be functioning until the lamp is replaced.
DAILY USE
& ROUTINE MAINTENANCE
1
2
3
4
Sensing
device
Sanitisation outlet
Place hands,
palms down,
beneath the dryer
Move backwards
and forwards in
the air ow
Turn hands,
to palms up
and repeat
backwards and
forwards motion
Finally rub
hands together
to remove any
nal dampness

6
COMPONENTS
& ELECTRICAL SCHEMATIC
Fuse
Heater
Thermal fuse
Heat switch
Brushed
motor
Power switch
Sensing
probe
Indicator
Temperatur
e
probe
Temperature
switches
Control
relay
Power
L
N
Components
Electrical Schematic
1
2
UV bulb
casing
UV bulb
casing
Heater
Inductor
PCB
Earth
Air
Outlet
Baseplate
Countersunk
screws
Allen key
Motor
Shell

7
PACKING LIST
A. Rawplug ........................................................x 8
B. 30mm Wall screws.................................................x 8
C. Splashback panel .................................................x 1
D. Wall sticker.......................................................x 1
E. Instruction manual ................................................x 1
F. Wall fixing template (double sided) ...................................x 1
G. Allen key .........................................................x 1
H. Sterillo unit .......................................................x 1
I. Warranty card ....................................................x 1

www.handydryers.co.uk