Hangar 9 ProSeal HAN135 User manual

HAN135
ProSeal™Covering Iron
Instruction Manual
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of
Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab
for this product.
Meaning of Special Language
The following terms are used throughout the product literature to indicate various levels of potential harm
when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a
little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage
AND a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral
damage, and serious injury OR create a high probability of superficial injury.
SPECIFICATIONS
Input voltage 110–120V, 60Hz
Current Draw 1.4A
Max. Temp. 469°F (243°C)
Thank you for purchasing the Hangar 9®ProSeal™covering iron. This covering iron features a thermostatically
controlled temperature maintenance system that actually monitors the heat and regulates power to maintain the
temperature settings on the dial.
IMPORTANT: Consult the instructions provided with the film for suggested iron temperature settings. Always
start with a lower setting than recommended and increase the heat slowly if necessary.
The ProSeal covering iron also features a non-stick coated ironing surface that allows the iron to glide over
the covering material without scratching. This coating may produce a light smoke the first time the covering
iron is used.
The specifically designed tip allows easy iron access between control surfaces and in hard-to-reach areas. A
convenient aluminum stand is also included.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product
before operating. Failure to operate the product correctly can result in damage to the product,
personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires
some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result
in injury or damage to the product or other property. This product is not intended for use by children without
direct adult supervision. Do not attempt disassembly, use with incompatible components or alter product in
any way without the approval of Horizon Hobby, LLC. This manual contains instructions for safety, operation
and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to
assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
CAUTION: Iron surface will become hot. Operating temperature can exceed 200°C (400°F). Use
extreme caution when operating this product to avoid burns.
Operation:
Plug the ProSeal covering iron into a suitable 110–120V AC outlet. Adjust the temperature control dial on
the covering iron to the recommended temperature for the covering you will be applying. The orange LED will
illuminate on the covering iron indicating the iron is heating to the set temperature. Once at the set temperature,
the green LED will illuminate, indicating the iron is ready to use. If the red LED is illuminated, the iron is above
the set temperature and will stop heating until the set temperature has been achieved.
TIP: We recommend starting below the recommended temperature for your covering, then increasing the
temperature as you work with the covering.
Shoe replacement:
The shoe for your covering iron (HAN135S ProSeal Covering Iron Shoe) can be replaced if it becomes scratched
or damaged. Use a #1 Phillips screwdriver to remove the four screws on the top of the covering iron. Carefully
separate the shoe slightly from the main body of the iron and rotate the shoe to expose the two internal screws
securing the heating element to the shoe. Use a #1 Phillips screwdriver to remove the two screws separating
the heating element from the shoe. Install the new shoe by attaching the heating element to the shoe, then
attaching the shoe back to the main body of the covering iron.
2-YEAR LIMITED WARRANTY
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will
be free from defects in materials and workmanship for a period of 2 years from the date of purchase.
What is Not Covered - This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage
due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation,
operation or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service by anyone
other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon
dealer, (vi) Product not compliant with applicable technical regulations, or (vii) use that violates any applicable
laws, rules, or regulations.

©2017 Horizon Hobby, LLC.
Hangar 9 and ProSeal are trademarks or registered trademarks of Horizon Hobby, LLC.
Created 10/16 54738
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR
REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT
LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE
PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy - Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that
Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective.
Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement
decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims.
SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND
EXCLUSIVE REMEDY.
Limitation of Liability - HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY,
REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT
LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product
on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse,
no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or
assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the
liability associated with the use of the Product, purchaser is advised to return the Product immediately in new
and unused condition to the place of purchase.
Law - These terms are governed by Illinois law (without regard to conflict of law principals). This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves
the right to change or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services - Your local hobby store and/or place of purchase cannot provide warranty
support or service. Once assembly, setup or use of the Product has been started, you must contact your local
distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the
event that you may need any assistance. For questions or assistance, please visit our website at horizonhobby.
com, submit an inquiry to [email protected] or call the toll-free telephone number referenced
in the Warranty and Service Contact Information section to speak with a Product Support representative.
Inspection or Services - If this Product needs to be inspected or serviced and is compliant in the country you
live and use the Product in, please use the Horizon Online Service Request submission process found on our
website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely
using a shipping carton. Please note that original boxes may be included, but are not designed to withstand
the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for
lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our
facility. An Online Service Request is available at http://www.horizonhobby.com/content/service-center_render-
service-center. If you do not have internet access, please contact Horizon Product Support to obtain a RMA
number along with instructions for submitting your product for service. When calling Horizon, you will be asked
to provide your complete name, street address, email address and phone number where you can be reached
during business hours. When sending product into Horizon, please include your RMA number, a list of the
included items, and a brief summary of the problem. A copy of your original sales receipt must be included for
warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the
shipping carton.
Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service
or replacement decisions are at the sole discretion of Horizon.
NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo battery, please
contact the appropriate Horizon Product Support office. Warranty Requirements- For Warranty
consideration, you must include your original sales receipt verifying the proof-of-purchase date.
Non-Warranty Service - Should your service not be covered by warranty, service will be completed and
payment will be required without notification or estimate of the expense unless the expense exceeds 50%
of the retail purchase cost. By submitting the item for service you are agreeing to payment of the service
without notification. Service estimates are available upon request. You must include this request with your
item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In
addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as
Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you
are agreeing to Horizon’s Terms and Conditions found on our website http://www.horizonhobby.com/content/
service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership.
If received, a non-compliant Product will not be serviced. Further, the sender will be responsible
for arranging return shipment of the un-serviced Product, through a carrier of the sender’s choice
and at the sender’s expense. Horizon will hold non-compliant Product for a period of 60 days from
notification, after which it will be discarded.
5-14-2015
WARRANTY AND SERVICE CONTACT INFORMATION
COUNTRY OF
PURCHASE HORIZON HOBBY CONTACT INFORMATION ADDRESS
United States of
America
Horizon Service Center
(Repairs and Repair Requests)
servicecenter.horizonhobby.com/
RequestForm/
4105 Fieldstone Rd
Champaign, Illinois,
61822 USA
Horizon Product Support
(Product Technical Assistance)
productsupport@horizonhobby.
com.
877-504-0233
Sales [e-mail]
800-338-4639