Hanover Agio User manual

HanoverOutdoorFurniture
IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:1‐800‐416‐3511
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:www.hanover‐products.com
Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(a)

ADS17500
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT
FRONT SEAT SUPPORT BAR
Fig.1
B
C
F
Fig.3
D E
FOOT CAPFOOT CAP
PARTS LIST PARTS LISTDESCRIPTION DESCRIPTIONORDER PART # ORDER PART #
SEAT FRAME BOLT COVER HW0022
FC0030
FOOT CAP
FACTORY ASSEMBLY
SEAT BASE
1/4" X 35 MM
BOLT
1/4" X 45 MM
BOLT
Ø6.5 X 1.0 MM
WASHER
HW0142
HW0040
HW0004
QTY QTY
1
A B C D E
F G1
2
2 2 2
1HW0252
Fig.2
IMPORTANT NOTE: Your sling seat may appear to be slightly warped. This is not unusual.
Proper assembly procedure will straighten out the sling seat in the frame. There are four bolts used to attach the seat frame to the seat base. After inserting all the bolts, each of these bolts must be tightened a few revolutions at a time in rotation. Step 1: Identify all parts packed in the carton against the parts list. Remove all protective materials. Set parts on a flat, non-abrasive surface to avoid scratching. If you are missing any parts or are unsure how to proceed with assembly, call our Customer Service Center immediately at 1-800-416-3511. Do not attempt to assemble chair if any parts are missing or damaged. IMPORTANT NOTE: Assembling this chair requires attaching the sling seat frame to the seat base. We recommend two people work together to assemble the chair since it is critical that all the holes in the seat frame are aligned exactly with the holes in the seat base. All bolts need to be inserted and tightened into the fixed nuts in a straight and direct path. Inserting the bolts at even the slightest angle could strip the nuts and bolts, damaging the entire chair. Step 2: Working from behind the chair, have another person stand in front of the chair and position the sling seat frame in between the arms of the seat base as shown in Fig.1 so that the holes on both sides of the upper portion of the seat frame back align with the fixed nut holes in the seat base. Step 3: Working from the front of the chair, add a washer to a 1/4"x45 mm bolt. From the underside of the front seat support bar, insert the bolt with washer through one of the holes in the seat support bar, into the fixed nut inside the lower front portion of the seat base as shown in Fig.2. Hand tighten 3-4 revolutions only. Do not tighten Completely. Repeat
for opposite side of chair. Step 4: From behind the chair, insert a 1/4"x35 mm bolt through the back arm portion of the seat base and into the fixed nut in the seat frame as shown in Fig.3. Make sure the bolt is inserted exactly straight! Hand tighten 3-4 revolution only. Do not tighten completely. Repeat for opposite side of chair. Step 5: Tighten all bolts with the hex bolt driver. Each bolt must be tightened a 3-4 revolutions only at a time. Begin with top left bolt. Move to bottom right bolt then to top right bolt, followed by bottom left bolt. Repeat this "X" pattern until all bolts are tight. Do not over
tighten bolts. Over tightening may strip bolts or nuts, damaging the entire chair. Cover 1/4"x35 mm bolts with bolt covers. Step 6: Examine the chair from the front. If the sling seat does not appear tight or straight in the seat base, repeat steps 3, 4 and 5. If you do not feel your chair is assembled properly, or you have any questions, call our Customer Service Center at 1-800-416-3511.
IMPORTANT NOTE: Damage to welds or frames resulting from over tightened bolts or
improper assembly is not covered under our warranty. Please read all instructions carefully
before assembly. If you have any questions regarding your assembly, call our Customer
Service Center at 1-800-416-3511.
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
HEX BOLT DRIVER
A
SLING TUBE CAP
FACTORY ASSEMBLY FC0358
AN0523
AN0524

ASSEMBLY INSTRUCTIONS
1
2
3After making any necessary adjustments to the alignment of the table, use the hex bolt driver to tighten
all bolts. Repeat until all bolts are tight. Over tightening may strip bolts. With the
help of another person, turn the table in the upright position.
Do not over tighten.
F1igure
Figure 2
A
C
F
EB
H
F
D
G
Attach a leg to the leg connector bracket by carefully guiding the bolts already in place on the table
legs (each leg has two bolts) through the holes in the leg connector bracket. Add a washer and a nut
to the end of each bolt as shown in the . Repeat on the other
three legs.
F2Hand tighten 2-3 turns only.igure
Place the table top upside down on a flat, non-abrasive surface. Attach a table leg to the table top by
using the bolts and washers as shown in the . Guide the bolts through the holes in the table leg,
into the pre-drilled holes in the table top. Repeat for the other three legs.
F1
Hand tighten 2-3 turns only.
igure

* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
PARTS IDENTIFICATION LIST
QTY
PARTS LIST DESCRIPTION ORDER PART #
A
B
C
D
E
F
G
H
I
J
ALT19517
12
Ø6.5 X 1.0 MM
WASHER HW0004
FOOT CAP
FACTORY ASSEMBLY FC0612
4
1
1
HEX BOLT DRIVER HW0006
1/4" X 18 MM BOLT HW0035
TABLE TOP
TABLE LEG
LEG CONNECTOR
BRACKET 1
BOLT COVER
HW0105
8
4
1
NUT COVER HW0027 8
HEX WRENCH
1/4" NUT
HW0014
HW0009
4
G0157
UMBRELLA HOLE
PROTECTIVE RING
FACTORY ASSEMBLY
AT53135
AT53136
AT53137