Hanover HSD0423-BRN User manual

10%(Continuous operation for 2 minutes at most
after pause for 18 minutes )
99.2lbs
1 inch/s
29.5"
49.2"
32-104°F
2
9810423
21.8"x11"x2.1"
47.6"x23.6"x0.7"MDF
Item No.
Column Number
Maximum Load
Max Speed
Highest Position
Lowest Position
Desktop
Duty Cycle
Applicable Temperature
Drawer

Ax8 Cx1
Bx8
D
M6 0.2"x0.2"
(With cross)
M6 0.16"x0.16"
x3
M4x12
E
1 2 3
4 5 6
7
121
211
4
2
1
3
5
46
7
818
Part List Installation Instruction
No. Part Qty No. Part Qty No. Part Qty
Tabletop Lifting column Handset
Feet Power plug Adaptor
Cable
Cable
mounts

2
4
Cx8
C
D
STEP2 Install the feet
Install the feet (4) to the lifting columns (2) with the
screw (C)and tighten it with 0.16"x0.16" allen key (D)
D
0.16"x
0.16"
2
1
Bx8
D
B
3
1
4
STEP1 Install the lifting column
Insert the column to the end to avoid
height differences; make the long side
of the column is parallel to the short
side of the tabletop.
Shortside of the desktop
Long side of the
lifting column
Install the lifting column (2) to the
tabletop(1), then tighten the screws (B)
with 0.16"x0.16" allen key (D)
Tighten
Insert
Insert the hexagon head of the column
along the wiring trough, the side of the
wire facing the motor
Tighten the screws(B) with 0.16"x0.16" allen key (D)
D
0.16"x
0.16"

2
1
x3
A
A
E
0.2"x0.2"
D
3
STEP3 Install the handset
Position the handset (3) as shown in the picture to align
the three screw holes on the tabletop, then fix it with the
screw (A)and tighten it with 0.2"x0.2" allen key (E).
3
6
5
8B
STEP4 Connect all cables to the adaptor
Do not connect the power before
the wiring is completed
Connect the switch cable
to the DC port
Connect the motor cable
to the M1 port
Insert the adaptor(6) to the bracket of the tabletop
Fix the cables to the tabletop with cable
management(7) to keep wires organized
Ripped Fixed
Organize
the lines

LED Display
(1) "▲" : Adjust the desk upwards
(2) "▼" : Adjust the desk downwards
(3) "1" : Position 1, first height position saved by the user
(4) "2" : Position 2, second height position saved by the user
(5) "3" : Position 3, third height position saved by the user
(6) "4" : Position 4, fourth height position saved by the user
Height Adjustable Function:
1.Press the "▲" button, the standing desk will rise up, press and hold to continue to rise,
when it rises to the highest point, the digital tube displays top
2.Press the "▼"button, the standing desk will drop down, long press and continue to drop
down to the lowest point, the digital tube displays bot
●
Height Memory Function:
1.When the desktop is in a static state, press and hold the button "1" for three seconds, the
buzzer will produce an audible prompt, and the display shows "S-1", which means the save
is successful, and then run the desktop to any height, click the button "1" Can run to the
original memory height
2.Buttons "2", "3" and "4" all have the same memory height function as button "1", just
repeat the above steps
●

Reminder Function:
1.When the height of the device is incorrect or an error code appears, the device needs to
be reset and corrected. At the same time, press and hold the "3" and "4" keys for three
seconds to enter this function.
2. After entering the reset function, the display shows "RST". At this time, press and hold
the "▼" button to reset the device. When the desktop drops to the lowest height, it starts
to rebound and move upwards until it displays "bot", which means the reset is complete.
●
29V DC power supply function:
1.When the standing desk is not in the reset state, after 30s from running to stopping,
the 29V DC power supply function will be turned on, and the 2pin at the back of the control
box will output a DC 29V voltage.
●
Anti-collision sensitivity adjustment - optional features:
1.Simultaneously press the "▲" button and "▼" button for three seconds to switch the
sensitivity, one operation to switch one gear, divided into 4 gears, A-0, A-1, A-2, A-3
2.The display shows “ ” to close the anti-collision function; the display shows “ ” high
sensitivity; the display shows “ ” Medium sensitivity; the display shows “ ” Low
sensitivity. (Factory default A-2)
3.When the desk rises or falls, it will rebound immediately when encountering obstacles,
which plays a protective role.
●
Code processing:
1.Reset function definition, the LED display shows “ ”or “ ”, at this time, press and
hold the “▼” button to start the device reset, when the desktop drops to the lowest height,
it starts to rebound and run upwards until it displays "bot", that is, the reset is complete.
2.If "E01" or "E02" appears, please let the table rest for more than 18 minutes before it can
be used normally.
●
3.If other codes appear and long press the "▼" button does not respond, please confirm
that the connection line is not damaged and the connection is normal, and the power is
cut for more than 10 seconds, and the power is turned on again, the display “ ”or “ ”,
then long press "▼ "Button to reset.
4.If you perform the above operations, the desk still does not operate normally, please
contact customer service.