HANYOUNG NUX NP100 User manual

Manual
NP100
Programmable Controller

3
CONTENTS
1. SAFETY INFORMATION
2. ORDERING INFORMATION
3. TERMINAL ARRANGEMENT
4. DIMENSION & PANEL CUTOUT
5. INPUT & OUTPUT
• Input Signal and Measurement Range
• Output type
6. NAME & FUNCTION
7. LIST OF SETUP ITEMS
8. SETUP METHOD
• Program Setup
9. SPECIFICATION
• Input
• Function
10. ALARM TYPE & CODE
11. FND DISPLAY
12. PROGRAM SETUP CHART
4
7
7
7
8
8
8
9
12
15
26
28
28
32
34
35
36

4
1. SAFETY INFORMATION
Before using the product, please read the safety information thoroughly and use it properly.Alerts declared in the
manual are classified to Danger, Warning and Caution by their criticality
DANGER indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury
WARNING indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in
minor or moderate injury
Danger
Warning
Caution
1. The contents of this manual may be changed without prior notification.
2. Before using the product you have purchased, check to make sure that it is exactly what you ordered.
3. Check to make sure that there is no damage or abnormality of the product during delivery.
4. The ambient temperature do not exceed 0 ~ 50 ℃ & The ambient humidity do not exceed 35 ~ 85 %RH (no icing).
5. Do not use this product at any place with corrosive(especially noxious gas or ammonia) or flammable gas.
6. Do not use this product at any place with direct vibration or impact.
7. Do not use this product at any place with liquid, oil, medical substances, dust, salt or iron contents.
(Use at the Pollution level 1 or 2)
8. Do not polish this product with substances such as alcohol or benzene.
9. Do not use this product at any place with excessive induction trouble, static electricity or magnetic noise.
1. If there is a possibility of an accident caused by errors or malfunctions of this product, install external protection
circuit to prevent the accident.
2. This product does not contain an electric switch or fuse, so the user needs to install a separate electric switch or
fuse externally. (Fuse rating : 250 V 0.5A)
3. When setting, “Input type selection number” must be selected in the Group Input(G.In) and also “Output type
selection number” must be selected in the Group Output(G.Out) before moving to other group. If not, data of other
group will be changed to the initial stage.
4. To prevent defection or malfunction of this product, supply proper power voltage in accordance with the rating.
5. To prevent electric shock or devise malfunction of this product, do not supply the power until the wiring is completed.
6. Since this product is not designed with explosion-protective structure, do not use it at any place with flammable or
explosive gas.
7. Do not decompose, modify, revise or repair this product. This may cause malfunction, electric shock or fire.
8. Reassemble this product while the power is off. Otherwise, it may cause malfunction or electric shock.
9. It you use the product with methods which are not specified by the manufacturer, there could be bodily injuries or
property damages.
10. Due to the danger of electric shock, use this product installed onto a panel while an electric current is applied.
Do not touch or contact the input/output terminals because they may cause electric shock.
Danger
Warning
Caution

5
10. Do not use this product at any place with possible thermal accumulation due to direct sunlight or heat radiation.
11. Install this product at place under 2,000 m in altitude.
12. Attach the bractets(2pcs) on the fixed halls and tighten with a screwdriver. Fixing torque is about 14.7 N·cm (1.5 kg·cm)
13. When the product gets wet, the inspection is essential because there is danger of an electric leakage or fire.
14. Use a compensating cable with thermocouple.
15. The lead wire resistance is small for RTD input use and please use the one which has no resistance difference to 3 wires.
16. To avoid inductive noise to input wires, seperate from the power and output wires.
17. Keep input wires away from output wires and use shielded wires to earth.
18. Use non-grounded sensor to R.T.D and thermocouple.
19. If there is excessive noise from the power supply, using insulating transformer and noise filter is recommended.
The noise filter must be attached to a panel grounded, and the wire between the filter output side and power supply
terminal must be as short as possible.
20. It is effective to use a twisted cable for power supply against noise.
21. If alarm function is not set correctly, alarm output can not be operated at a trouble.
22. When replacing the sensor, please turn OFF the power supply.
23. Use an extra relay when the frequency of operation is rather high. In this case, SSR output type is recommended.
•Electromagnetic switch : Proportional cycle time is Min. 20 sec
•SSR : Proportional cycle time is Min. 1 sec
•Contact output life : Mechanical : Min.10 million times (no load)
Eletrical : Min. 100 thousand times (rated load)
•SSR drive pulse voltage, 4 ~ 20 mA DC are not insulated with internal circuit.
24. The instrument has IP65. Use rubber packing when installing the instrument to panel.
25. Do not connect anything to the unused terminals.
26. After checking polarity of terminal, connect wires at the correct position.
27. When this product is connected to a panel, use a circuit breaker or switch approved with IEC847-1 or IEC947-3.
28. Install the circuit breaker or switch at near place for convenient use.
29. Write down on a label that the operation of circuit breaker or switch disconnects the power since the devise is installed.
30. For the continuous and safe use of this product, the periodical maintenance is recommended.
31. Some parts of this product have limited life span, and others are changed by their usage.
32. The warranty period for this product including parts is one year if this product is properly used.
33. The heater power supply and the instrument power supply should be connected using the same power supply
when a heater break alarm.
34. When the power is on, the preparation period of contact output is required. In case of use for signals of external
interlock circuit, use with a delay relay.
35. When changing a contorller to extra one, please check all parameters.

6
● Summary
Program temperature controller is consisted of three types of
modes: operation indicator mode, engineering mode, and
program mode.
Operation indicator mode is displayed when the power is
ON and it indicates process value and set value, process
value and output volume, and remaining time of the
corresponding segment when in operation.
Engineering mode sets up the basic functions of the
instrument including types of input (sensor) and output,
communication, retransmission, alarm, control output, PID,
and auto tuning.
Program mode sets up the control program. It establishes
the number of program repetition, pattern number, segment
number setup, program start condition, time signal, program
ending mode, and each segment’s parameter.
● Feature
Function Description
Option RS 485 / 422, Time signal 2 points
PV display
Digit number 4 digits
Accuracy ±0.1 %
Sampling time 250 ms
Input type Universal input (selectable by parameter) refer to page 8
Control
Output Output type
Universal output (selectable by parameter) refer to page 8
SSR / SCR
Relay
Retransmission output Current / SPS (power suppy for sensor)
(Use RET output terminal)
Alarm output Relay 2 points
Time signal
output Transistor 2 points
Pattern & Segment number 2 patterns & 20 segments (1 PT is max. 10 seg.)
Communication
Standard RS485/422
Speed 600 ~ 9600 bps
Max. Com. line 31
Hard Ware
Measurement input 1 point
Contact input 3 points (RUN,RESET,HOLD)
SCR / SSR pulse 1 point (Current or SSR output)
Retransmission output 1 point
Relay control output 1 point (C contact)
Alarm output 2 points (A contact)
Transistor output 2 points (Time signal)
Power supply 100 - 240 V AC 50 - 60 ㎐

7
[Unit : mm]
● Dimmension ● Panel cutout
min
Model Code Information
NP100-   Programmable Controller
Control type 0 Universal type (Heating)
Option
0 None
1 Time signal 2 points
2 RS 485/422
3 Time signal 2 points +RS 485/422
2. ORDERING INFORMATION
3. Connection diagram
4. DIMENSION & PANEL CUTOUT
Main power must be OFF before wiring
Caution
Use panels with 2 ~ 10 mm tickness steel sheet.
Caution
Caution
● ground-wiring ( )
- Ground connection cable is a thick wire that is over 2 ㎟ in width. Wire with more than the third type ground connection
(below 100Ω ground connection resistance).
- The length of the ground connection cable must be within 20m.
- Ground 1 point from the ground terminal.
- Do not spread cable between the ground terminals.
주 의
Operate after disconnecting the main
power and confirming the discontinuation
of power to the cable connected to the
main power by using a tester. There is
danger of possible electric shock. Avoid
any contact with the terminal when
sending electricity.
Caution

8
※ Display range : -5 % ~ +105 % of range *1 : below 0 ℃ : ±0.2 % of F.S ±1digit
*2 : 0 ~ 400 ℃ : ±5 % of F.S ±2digit
● Control output type
● Input type and Measurement range
※ ① ~ ⑦ : Terminal number
Caution
● Measurement Input Wiring
- When wiring the input line, cut off the controller and the external power.
- Be careful with polarity and wire the input signal at some interval from power circuit and ground connection circuit.
- Use shielded input cable when wiring and earth the shield 1 point.
5. INPUT & OUTPUT
Input type Code Input Range (℃) Accuracy
Thermocouple
(T.C)
K *1 -200 ~ 1370
±0.10 % of F.S
±1digit
K *1 -199.9 ~ 999.9
J *1 -199.9 ~ 999.9
E *1 -199.9 ~ 999.9
T *1 -199.9 ~ 400.0
R 0 ~ 1700
±0.15 % of F.S
±1digit
B *2 0 ~ 1800
S 0 ~ 1700
L *1 -199.9 ~ 900.0 ±0.1 % of F.S ±1digit
N -200 ~ 1300 ±0.2 % of F.S ±1digit
U *1 -199.9 ~ 400.0
±0.1 % of F.S
±1digit
W 0 ~ 2300
PlatinelⅡ 0 ~ 1390
RTD JPT100 -199.9 ~ 500.0
PT100 -199.9 ~ 640.0
Direct
voltage
1 - 5 V **
Scaling range
SL-L ~ SL-H = -1999 ~ 9999
**When using current input, use the resistor
250 Ω 0.1 % on input terminal to use
4 - 20 mA DC input.
0 - 10 V
-10 - 20 mV
0 - 100 mV
Caution
● Control output wiring
- In case of wiring or eliminating the control output, cut off the controller and the external power.
- Use a shielded line for SSR pulse or Current output when wiring.
Output symbol Control output (OUT1) Control output (OUT2)
Relay output SSR / SCR (Current) RET / SPS
ON–OFF control* ① - ② - ③
RET(Retransmission output) /
SPS(External power supply)
⑥ - ⑦
SSR ④ - ⑤
SCR ④ - ⑤
Relay ① - ② - ③

9
6-1. The function of individual LED
● Function description
6. NAME AND FUNCTION
LED display Function
① display lamp Lights when there is an ascending section of the segment.
② display lamp Lights when there is a soak section of the segment.
③ display lamp Lights when segment is descending section.
④ PT1 display lamp Lights when selecting the pattern 1.
⑤ PT2 display lamp Lights when selecting the pattern 2.
⑥ RUN display lamp Lights when the program is in operation.
⑦ WAIT display lamp Lights when WAIT is in operation while the program is running on.
⑧ HOLD display lamp Lights when HOLD is in operation while the program is running on.
⑨ MAN display lamp Lights while manually operating
⑩ AL1 display lamp Lights when Alarm 1 is in operation
⑪ AL2 display lamp Lights when the Alarm2 is in operation.
⑫ TS1 display lamp Lights when the time signal 1 is in operation
⑬ TS2 display lamp Lights when the time signal 2 is in operation
⑭ OUT display lamp Lights when the control output is ON.
⑮ AT display lamp Lights during the auto tuning.
⑯ SEG1~10 display lamp Display present segment while the program is in operation.
⑰ PV display lamp Display process value.
⑱ SV display lamp Display set value.

10
6-2. Function of control key
Caution
- Press the key firmly with your finger
- Do not press the key with any sharpened thing. It could cause key malfunction
Caution
● Automatic/Manual Operation Selection Method
Press the AUTO/MAN key on the front panel to choose automatic and manual operation.
On manual mode, the MAN LED will be turned on and MAN LED will be turned off for automatic mode.
The control output value can be changed continuously with the operation of ascent and descent keys.
Name Function
• Operate the current pattern number.
• Input the parameter setup value • Use when moving the parameter
• Press 2.5 seconds or longer to alternate the operation indicator mode and the
engineering mode.
• Exit running program and convert to stop.
• Exit runing MAN operation and convert to reset mode.
• Use to finish program setup mode.
• Press to move to other digit.
• Use for changing the parameter value.
• Use for moving to other group.
• Use for changing the parameter value.
• Use for moving to other group.
+ • When the program is running, press it to hold ongoing segment.
• Press it again to release the holding
+ • Exit the running segment while operating program and operate the next
segment.
• Use to change the pattern number.
• Press key to alternate P1 and P2
• AUTO : Use for changing from MAN control to Program Mode.
• MAN : Use for changing Program mode to MAN control.
• Press key to alternate AUTO and MAN.

11
6-3. Function of 4 digits LED
1. Digital Formation
4D 3D 2D 1Digit
2. Possible range of maximum indication using the or button.
3. Rounding Up & Off of Digits
·When it becomes “9” in any digit besides the 4th digit (4D), it will
be rounded up to the next digit when the button
is pressed continuously.
·Rounding Up
·When the 4th digit indicates “9”, there will be no changes despite
pressing of continuously.
① Represented data is “+”.
 When it becomes “0” in any digit besides the 4th digit, it will be rounded
off to the next digit when the button is pressed continuously.
② Represented data is “-”,
 When “9” is indicated, it will be rounded off from the next digit when the
button is pressed continuously.
·Rounding Off
4. Maximum & Minimum Indication
It indicates the greatest or the least of the selected item when it gets out of the range of the selected item (parameter).
If WTM = 0.00 ~ 99.59
 If user selects over 99.60, it sets up 99.59, which is the maximum value. Moreover, it sets up the
minimum value of WTM 0.00 if less below -0.01 is selected.
Ex.)
5. Operation of Button
4D 3D 2D 1Digit
It blinks in its change operation position.
7. Position of “ - (minus)”
·It is always indicated in the 4th digit.
6. Operation of button
Use , , buttons to change to the desired value. Then move to the next setup item
(parameter) after registering with the button.
However, this setup value must be within the range of each setup item (parameter). button leads to the
next setup item without pressing any other buttons besides the button.

12
7. LIST OF SETUP ITEMS
AT.M
AT
1.P
P4Gr
1.I
1.D
1.M R
2.P
2.I
2.D
2.MR
3.P
3. I
3. D
3.MR
4.P
4.I
4.D
4.MR
AR
PID
FUZY
TMU
WTH
PWR.S
A1TY
A1DB
AL-1
A2TY
A2DB
AL-2
HYS
PR-S
BPS
PRI
ST P
DLN
ADR
RP.T
OUT
O.A CT
CT
PO
OL-H
OL-L
FR-L
INP
FR-H
DP-P
SL-H
SL-L
RJC
FILT
BIAS
B.OUT
P.E1
P.E2
RET
RET.H
RET.L
P1Gr P2Gr P3Gr
NP100
WZ
PID≠OFF
Caution
- Preparation must be carried out in engineering mode when operating the controller.
- There are setup mode for input and output functions and setup mode for control
function in engineering mode but must start with the setup of the input and output
functions.
※ Remain time of segment is
indicated in running
【Operation indicator mode】
【Engineering mode】
Power
(ON)
Process value
Set value
Process value
Output value
Display remain
time of segment
+ 2.5 sec.
or
PID=OFF
※Displayed in running condition
Caution
1) When control setup group recovers from a power failure, it resets if selected 〞COOL〟 from the
control mode but keeps operating the program just before the power failure if 〞HOT〟 is selected.
2) When power turns on from its OFF mode in manual operation condition, it operates in the output of the
manual operation condition if “HOT” is selected from the motion mode at the time of power recovery of
the control setup group.
Operation when power is on.

13
AT.M
AT
1.P
P4Gr
1.I
1.D
1.M R
2.P
2.I
2.D
2.MR
3.P
3. I
3. D
3.MR
4.P
4.I
4.D
4.MR
AR
PID
FUZY
TMU
WTH
PWR.S
A1TY
A1DB
AL-1
A2TY
A2DB
AL-2
HYS
PR-S
BPS
PRI
ST P
DLN
ADR
RP.T
OUT
O.A CT
CT
PO
OL-H
OL-L
FR-L
INP
FR-H
DP-P
SL-H
SL-L
RJC
FILT
BIAS
B.OUT
P.E1
P.E2
RET
RET.H
RET.L
P1Gr P2Gr P3Gr
NP100
WZ
PID≠OFF
Caution
● Mode Setup
- Mode setup is recommended after completing the Program operation since the set value varies in accordance with the
setup of the specific parameter.
- Each parameter may not be indicated in accordance with the selection of form, addendums, control type and varieties of
the control system.
: It is indicated when option is
ordered. * : It is not indicated in ON/OFF control.
# : It is indicated in running.

14
Process value
Set value
G.RPT
SEG.N=0
Power
(ON)
【Program mode】
RPT
G.PT
PT.NO
SEG.N
n.SSP
n.STC
n.T10
n.JC
n.T2F
n.T20
n.T1F
n.PI 1
n.TM1
n.SP1
n.PI 2
n.TM2
n.SP2
n.PI A
n.TMA
n.SPA
SEG.N=1 SEG.N=2 SEG.N=10
NP100
Process value
Output value
Display remain
time of segment
【Operation indicator mode】
PT.NO=n
PT.NO=0
- We recommend you to use program mode after engineering mode is closed.
- A set up value is changed and initialized depending on change of particular engineering mode.
- There is a mode which cannot show up depending on controller's types, optional items,
and control types, etc.
Caution
+ 2.5 sec.
: It is indicated when option is ordered.

15
● Model NP 100 program temperature controller is divided into operation indicator mode and
program mode and this program mode is further divided into engineering group and program group.
8-1. Engineering Group Setup
8. SETUP METHOD
Operation
Indicator Mode
Operation indicator mode is displayed when the power is ON and it indicates process value and set value,
process value and volume of output, and remaining time of the corresponding segment when in operation.
Engineering
Group
Engineering mode sets up the basic functions of the instrument including types of input and output,
communication, retransmission, alarm, controlling movement, PID, and auto tuning.
Program
Group
Program mode sets up the control program. It establishes the number of program repetition, pattern
number, segment number setup, program start condition, time signal, program ending mode, and each
segment’s parameter.
Power
ON (Press 2.5 second.)
Engineering group
Program group
(1.Input setup group)
8-1-1
8-1-2
8-1-3
8-1-4
8-1-5
8-1-6
8-1-7
8-1-8
(2.Output setup group)
(3.Communication setup group)
(4.Retransmission setup group)
(5.Alarm setup group)
(6.Control setup group)
(7.PID setup group)
(8.Refer to configuration group of Automatic Calculation, ※Possible to display when program is operating.)
(refer to page 16)
(refer to page 17)
(refer to page 18)
(refer to page 19)
(refer to page 20)
(refer to page 21)
(refer to page 22)
(refer to page 23)
※Press button to enter the engineering mode from each setup group
Caution
※ Must start with the setup of the input and output.
Caution
- When controller is running on, preparatory work should be operated on engineering mode.
- Since there are set up mode of input and output function and mode of control function, please set up an order like input  output  other groups.
- Because a set up point can be changed and initialized depending on particular engineering mode,
we recommend you to record a set up point which is set up by engineering mode

16
8-1-1. Input Setup group
1) Selection of Input Type :
NP100 Program Temperature Controller supports universal input and can be conveniently used by selecting
and setting up the input signal symbol of the “Input Type Range” List. This list includes the application input
sensor and input types in accordance with voltage among the total of 18 types of input such as 12 types of
thermocouple input (13 types of range), 2 types of R. T. D input, and 4 types of direct current voltage input.
2) Selection of Maximum and Minimum Range :
Select the maximum and minimum value of the range within the maximum range for the setup item in
changing the range.
3) Setup of Decimal Point Position :
When selecting voltage input (V, mV) for the input type, decimal point can be indicated by selecting the
position of first through third in order to indicate process value in decimals.
(Select “1” to indicate one decimal place “000.0”.)
4) Selection of Maximum and Minimum Scale :
Select the maximum and minimum scale when selected voltage input (V, mV) for the input type.
5) Selection of Temperature Compensation :
As for the thermocouple input, select “ON” for the selection of temperature compensation to compensate
voltage for the terminal temperature. Otherwise, it will show declination as much as the terminal
temperature (surrounding temperature).
6) Selection of Process Value Filter :
When instability of the measurement value for the digital instrument is severe due to the external noise,
reduce the instability of the process value by selecting the filter value.
7) Selection of Process Value Bias :
Select correction value when it is necessary to correct the process value due to the error in input sensor.
8) Selection of Burn-Out Operation :
As the safety mode of output in OFF condition by ordering the maximum or minimum value and comparing
with the set value when input (sensor) is disconnected, maximum process value is indicated if UP is
selected and minimum is indicated when DOWN is selected, thus output remains in OFF condition.
Signal Item Setup range Display condition Initial value
Input group Setup below items.
Input type selection Refer to Input type and measurement range Always K(1)
Max. limit selection Refer to Input type and
measurement range
(FR-H > FR-L)
Always
1370
Min. limit selection -200
Decimal point position 0~3 In Voltage input 1
Max. scale setup -1999~9999
(SL-H > SL-L)
In Voltage
input
100.0
Min. scale setup 0.0
Temperature compensation ON , OFF TC ON
PV filter OFF , 1~120 Always OFF
PV bias -100~100 %(EUS) Always 0 %
Burn-out OFF , UP ,DOWN Always UP

17
8-1-2. Output Setup Group
1) Selection of Output Type :
Control output can be selected from the relay on-off output, relay PID control output, SSR Driving Pulse
output, and voltage output by choosing “Output Type Selection Symbol” from the Control Output Type List.
2) Selection of Heating & Cooling control :
Control method includes controlling by heating and cooling by freezing function.
Choose REV (reverse motion) for heating control and DIR (ordinary motion) for cooling control.
3) Heating Cycle Time :
When selecting relay or SSR output for the control output, it is an item that selects the frequency of ON-OFF
in proportion to output. Generally, set 30 seconds for the relay output and 2 seconds for the SSR output in
consideration of the life span.
4) Hysteresis :
This item sets the range between the ON temperature and OFF
temperature when relay ON-OFF control is selected from the control output.
5) Preset Output Volume :
This is useful when preheating condition must be maintained through
continuous output volume previously set up by disconnecting the output
from the PID calculation during the burn-out (disconnected sensor) A/D error.
6) Maximum & Minimum Value of Output :
This item allows the setup of maximum and minimum percentage in which the output volume of the control
output would be operated by.
Reverse motion(REV) Ordinary motion(DIR)
SV SV
ON if PV ‹ SV ON if PV › SV
Hysteresis
SV
Output
PV
ON
OFF
Signal Item Setup range Display condition Initial value
Output group Setup below parameters.
Output type
selection
Refer to the output's types
ON/OFF : ON/OFF
SSR : Contact-less relay output
SCR : Current Output(4 - 20 mA)
RLY : Relay Output
Always RLY
Heating / Cooling
control selection REV : heating, DIR : cooling Always REV : Heating
Heating cycle time 1 ~ 1000 sec. SSR, Relay 30 sec.
Hysteresis 0 ~ 100 % (EUS) ON/OFF control 0.5%(EUS)
Preset output volume -5.0 ~ 105.0 % Always 0.0
Max. output value OL-L+1Digit ~ 105.0 % PID
control
100.0 %
Min. output value -5.0 ~ OL-H -1Digit % 0.0 %

18
8-1-3. Communication Setup Group
Caution
● PC-LINK Communication / LADER Communication Wiring
- Must disconnect the controller and the external power source when connecting to the communication terminal due to the
danger of electric shock.
- Connect the termination resistor (220Ω 1/4W) at the end or master located at the both ends of the
communication equipment.
Signal Item Setup range Display condition Initial value
Communication
setup group Setup below items.
Protocal selection PCL.0 : PC LINK
PCL.1 : PC LINK SUM
Option
PCL.0
Communication rate
(BAUD RATE) 600/1200/2400/4800/9600 bps 9600
PARITY NONE/EVEN/ODD NONE
STOP BIT 1 or 2 bit 1
DATA LENGTH 7 or 8 (except PC Link : 8) 8
ADDRESS 1 ~ 99 (max. 31 devices) 1
RESPONSE TIME 0 ~ 10 0
1) Selection of communication protocol : Select PCL.0 when PC LINK come out and
select PCL.1 when PC LINK SUM come out.
2) Selection of communication speed : 600/1200/2400/4800/9600 bps
3) Parity Check : Select among NONE, EVEN and ODD
4) Stop Bit : Select 1 or 2
5) Select length of data : Select 7 or 8 (Select 8 except for PC LINK)
6) Address : 1 ~ 99, But, up to maximum 31
7) Response time : 0 ~ 10 (Conditioning time + Response time) ms
※ Response time = (handling time + response time) × 10 ms

19
Signal Item Setup range Display condition Initial value
Retransmission
setup group Setup below items.
Retransmission
output selection PV, SV, MV(output volume), SPS Always PV
Max. Retransmission
output
T.C, R.T.D : FR-H~FR-L
mV,V : SL-H~SL-L (RET.H > RET.L)
RET=PV
MV,SV
Selected
T.C,RTD : FR-H
mV, V : SL-H
Min. Retransmission
output
T.C, R.T.D : FR-H~FR-L
mV,V : SL-H~SL-L (RET.H > RET.L)
RET=PV
MV,SV
Selected
T.C,RTD : FR-H
mV, V : SL-H
8-1-4. Retransmission Setup Group
Caution
● Retransmission Output Wiring
- Must disconnect the controller and external power source when setting up/removing a receiver since there is a danger
of electric shock.
- Use same terminal for retransmission output and SPS output. Use of the terminal with what function of output is selected
through parameter.
- 4/20m ADC is outputted for the retransmission output.
- When using the retransmission output, it is impossible to use the SPS function for sensor.
● SPS Output Wiring for Sensor
- Must disconnect the controller and external power source when setting up/removing a sensor since there is a danger
of electric shock.
- Same terminal is used for the SPS output and the previous retransmission output. Which side a terminal is outputted and
used is set up depending on the parameter. (24 V DC 20 mA DC MAX)
1) Selection of retransmission Output :
Process value, output volume or setup value can range from 4 - 20 mA DC as retransmission output and
when SPS is selected, power for external sensor will be outputted. (24 V DC 20 mA max)
2) Selection of Maximum & Minimum Retransmission Output :
4 - 20 mA DC output can be selected within the range of value from the maximum range selection (FR-H)
and the minimum range selection (FR-L) in case of thermocouple or R. T. D input. As for the voltage
output (V, mV), select the desired maximum and minimum range within the maximum scale (SL-H) and
(SL-L).

20
EX) PUL selection CONT selection
0.5 sec.
ONON OFF
8-1-5. Alarm Setup Group
Caution
● Alarm Output Wiring
- In relay close contact output, use relay to operate ON/OFF when the close contact capacity exceeds 240 V AC,
resistance 1 A, and 30 V DC resistance load 1 A.
- Connect the Bleeder resistance for the current to flow more than the opening and closing volume of the relay when opening or
closing of small amount of current.
- There is life span ([Resistance load] for over 100,000) for relay.
Connect CR Filter (when using AC) or diode in the direct current L load).
Signal Item Setup range Display condition Initial value
Alarm setup group Setup below items.
Alarm 1 selection OFF / 1~22
Refer to “Alarm type and code”
(33, 34 page)
Option
3
Alarm 2 selection 4
Dead band of Alarm 1
0.0 ~ 100.0 %(EUS) Option 0.5 %
Dead band of Alarm 2
Alarm 1 set value Absolute value : 0.0~100.0 %(EU)
Deviation value : -100.0~100.0 %(EUS)
0.0
Alarm 2 set value 0.0
Patter 1 End OFF,PUL,CONT code 21
selection
OFF
Patter 2 End OFF,PUL,CONT OFF
1) Alarm - Select 1 or 2 Types :
Select code number of the Alarm type from the “Alarm Type and Code” list.
2) Alarm - Set up Dead Band 1 or 2 :
Set the ON-OFF width (dead band) when operating Alarm 1 and 2.
3) Alarm - Set Value of 1 or 2 :
Set value for Alarm 1 & 2.
4) Pattern 1 ending signal :
Since there is no separate output, pattern 1 ending signal setup item will be indicated when selected
number 21 from the Alarm 1 type selection. (However, pattern-1 ending signal will not activate when
pattern - 2 is selected from the setup item at the completion of the program.)
5) Pattern 2 ending signal :
Pattern-2 ending signal setup item is indicated when #21 is selected from the Alarm 2 type selection.
(Pattern ending signal setup item will not be indicated if #21 is not selected.)
Here, if OFF is selected from the pattern ending signal setup item, it doesn’t activate, PUL allows
output to be on for about 0.5 seconds and lastly if CONT. is ending, already setup alarm output will
continue on.
Press RST Key to remove the alarm.

21
【 Fuzzy Function 】
PV
Target SV
Subsidiary target SV
PV
Start FUZZYreasoning Time
8-1-6. Control Setup Group
Signal Item Setup range Display condition Initial value
Control setup group Setup below items.
Fuzzy function
selection OFF/ON Except ON / OFF OFF
Time unit selection HH.MM (00 hr. 00 min.)
MM.SS (00 min 00 sec.)
Always
HH.MM
Wait zone setup OFF/0~max. range OFF
Wait time setup OFF / 0.01~99.59 OFF
Power recovery
motion mode COOL / HOT COOL
1) Selection of Fuzzy Function :
Fuzzy function is an over shoot inhibitory function using the fuzzy reasoning. Fuzzy function can provide
control effects in the following situations
· Starting the control when there are variation between the desired set value and actual process value
· Wanting to reduce the operative preheating period
· Having severe load changes
· Having frequent changes to set value
2) Selection of Time Unit :
Maximum of 99 hours 59 minutes or 99 minutes 59 seconds can be selected in the setup item for the
selection of time unit.
3) Setup of Wait Zone :
Process value must agree in accord to the process of programmed set value in program temperature
controller but unpredicted events occur. Here, if the temperature variation set in the wait zone when
moving segments, program can continue on to the next segment. However, if it is outside the
variation range, it doesn’t move on from the current segment to the next segment but rather waits until it
enters the set range of wait zone.
4) Setup of Wait Time :
When the process value doesn’t agree with the progress of the programmed set value in the
program temperature controller, in other words, when the process value is not controlled within the range
of set variation between the set value + the wait zone, program continues on when the wait time elapses.
5) Power Recovery Motion Mode :
Can choose between COOL or HOT in the set up item. If COOL is selected, the system resets when
recovered from the power failure and if HOT is selected, it continues on from the segment operated just
before the failure.
※ However, must start from the beginning of the segment even if the system recovers to the segment just
operated before the power failure.