HANYOUNG NUX MC9 Series User manual

MANUAL
MC9 series
Multi-channel Temperature Controller
A/S¯‹•˛„…›”扔:080-979-1010 ¢ˇ¢ˇ
TThhaannkk
yyoouu vveerryy mmuucchh ffoorr ppuurrcchhaassiinngg HHAANNYYOOUUNNGG pprroodduucctt..
PPlleeaassee
rreeaadd tthhiiss mmaannuuaall ccaarreeffuullllyy aanndd kkeeeepp tthhiiss ffoorr ffuuttuurree uussee..
MA0401E070914
HEAD OFFICE
1381-3, Juan-Dong, Nam-Gu Incheon, Korea
TEL: [phone] - 4697 FAX:[phone] - 4696
http://www.hynux.com E-mail. [email protected]

1
This user guide is protected by co pyright and we have all the rights related to it.
Without prior authorization fro m HANYOUNG, this guide and any parts contained in this
guide cannot be reprod uced, copied, or translated in other languages.
Contents of this guide will be provided in this form and can be edite d o r changed
without prior notice d.
This guide includes implied guarantee or suitabilit y for a c er tain purpose, and it does
not offer any guarantee for those that do not limit this mat ter.
Every programs contained in this pro duct is protected by co pyright. Without prior
authorization fro m HANYOUNG, this product and any parts contained in this pro duct
cannot be reprodu ced, copied, or translated in another language.
Every title, s y m b ols, figures, service marks, and etc. in this guide or the pro duct are
legally re gistere d.
HANYOUNG
NUX
#1381-3, Juan 5-dong, Nam-gu, Incheon, Kore a
TEL: [phone] FA X: [phone]
ht tp://www.hynux.net
¸‚fi·´–

3
1 BEFORE STA RTING
1
- 1. CHECK THE CONTENTS
Thanksfor purchasing Multi-channels temperature Controller.
This manual shows how to install and use.
The contents of this paragraph are as follows.
¡ Check the contents of the pro duct
¡ Safety Information
¡Æ Damaged product
In case the product has external damage or some contents are missing, please contact
the place where you purchased or our sales department.
Please check whether the following packing contents are included or not.
¡ Instruction Manual
¡ MC9 Main Body
¡ Fixing pin : 2 pcs
¡ Impedance 250§ in case of Input V DC : 8 pcs
MC9 Main body Fixing pin
Impedance 250§
Instruction Manual
§§CChheecckk
ppaacckkiinngg ccoonntteennttss
2
‚æ ´
1-1 Check contents
1-2 Safety Information
2-1 Suffix Cod e
2-2. Input Ty pe & Range Cod e
2-3. Rating
2-4.Dimentions & Panel Cutout
2-5. Terminal Arrangement
2-6. Name & Function
3-1. Flowchart of Parameter
3-2. Parameter Range & Initial Value
3-3. Monitor Display
3-4. Operation Mod e
3-5. Function Mod e
3-6. Setup Mod e
4-1. Setting each Channel
5-1. RUN/STO P
5-2. Batch Setting
5-3. Alarm
5-4. Multi-Memory Zone
5-5. Scan
5-6. RUN/STOP Selection
6-1. Input
6-2. Output
6-3. Communication
6-4. Error Code
3
4
6
8
9
10
111
4
151
617
181
92
3
29
33
34
35
39
40
41
42
43
44
44
11
BBeeffoorree SSttaarrttiinngg
22 IInnssttaallll
33
BBaassiicc OOppeerraattiioonn
44
SSeettttiinngg MMeetthhoodd
55
FFuunnccttiioonn
66 SSppeecciiffiiccaattiioonn

5
- Under following conditions, repair will be charg ed even during warranty perio d.
- Breakdowns due to user’s misuses
- Breakdowns due to natural disasters
- Breakdowns due to moving the pro duct after installation.
- Breakdowns due to modification of the pro duct
- Breakdowns due to power troubles
- Please call our customer service for A/S due to bre a kdowns.
¡Æ Notice
for installation
Please
- In case of electrical wiring, please p ower off all of pro d u c t s
- Please do not touch the product with wet hands. It can cause electric shock.
- Do not expose the product to any gas pipe, lightening ro ds, or electrical wires. It can
cause explosion and ignition.
- Please do not transfer electricity before installation of this pro duct is completed. It
can cause breakdowns.
- It can cause electrical shock and fire when impro per power source is used.
- Please do not install the pro duct inclined.
- Please avoid installing the pro duct for following places where
- People can touch terminal unintentionally.
- it is exposed to mechanical shock or vibration
- Danger of corrosion or combustion of gas exist
- Temperature changes too frequently
- Temperature is either to o high (Over 50¡) or to o low (Below 0¡)(Ifyou use our
product below 10¡, please run warming up over 30 minutes)
- It is expo s ed to dire ct ra y s
- It is exposed to electr omagnetic waves too much
- Humid place (Over 85% humidity places)
- It has many combustible objects
- It has dusts and salinity
- It is exposed to an object that generates heat
- It is exposed to noise.
4
¡Æ Safety
notice
for this user
manual
- Please make this manual to be delivere d to the final user and to be placed where
can be found and seen easily.
- Please install and operate this pro duct after r eading this manual carefully.
- This manual contains detailed information about the pro duct and any matters not
mentioned in this manual cannot be guaranteed.
- This manual is written carefully, but please call us if you find any errors, parts that
can be improved, and omission.
- Contents of this user manual can be edite d without prior notice for improvement and
modification of the pro duct.
¡Æ Safety
notice
for
the
product
- For safety and securit y of the s y stem that is connected to the pro duct, please read
and follow this manual carefully.
- We are not responsible for any damages and safety problems due to disregards of the
manual or lack of care of the pro duct.
- Please install any extra safet y circuitr y or other safety materials outside the
product for safety of the pro gram that is connected to the pro duct.
- Do not disassemble, repair or re c onstruct the pro duct. It can cause electric shock,
fire, and errors.
- Do not give impact to pro ducts. It can cause of damage or malfunction.
¡Æ Notice
about responsibilities
- Unless it is included company’s conditions for warrantee, we are not re s ponsible for
any warranties or guarantees.
- We are not responsible for any damages and indirect loss of the use or third person
due to unpredicted natural disasters.
¡Æ Notice
about quality guarantee conditions
- The warranty for this pro duct is valid for 1 y ear fro m p u rchase, and we will fix any
breakdowns and faults fro m p ro p er uses as it is mentioned in this manual for fre e.
- After the warranty perio d, repair will b e charg ed according to our standard policies.
1
- 2. SAFETY NOTICE

7
MODEL
MC9-8
Control Direction
Input
Output1~4
Output 5-8
Option(Alarm,Communication,
(Contact Input & HBA)
* Loading Alarm Output AL1
basically
Power Voltage
D
R
§
N
M
S
T
4
5
N
2
3
4
1
2
3
M
S
T
4
5
CODE
§-§ §- § §-§-§
CONTENTS
Digital Multi channels Temp. controller
Dire ct operation
Reverse Operation
Refer to inputs sheet
Relay
SSR
TIIAC
Current (4 - 20 mA)
Current (0 - 20 mA)
NONE (Input 5 - 8 : Indicator)
Relay
SSr
TRIAC
Current (4 - 20 mA)
Current (0 - 20 mA)
None
RS 232 + Contat Input
RS 422 / 485 + Contat Input
HBA
24 V a.c / d.c (50/60Hz) - Not ready
100 - 240 V a.c (50 / 60 Hz)
100 V d.c
§§SSuuffffiixx
CCooddee ooff 88 cchhaannnneellss
6
MODEL
MC9-4
Control Direction
Input
Output1~4(Heating
Output)
Output 5-8
(Cooling Output)
IN case of D&R, N is fixed.
IN case of W, choose among
M, S, T, 4 & 5
Option(Alarm, Communication,
(Contact Input & HBA)
* Loading Alarm Output AL1
basically
Power Voltage
D
R
W
§ §
N
M
S
T
4
5
N
1
2
3
4
1
2
3
M
S
T
4
5
CODE
§- § §- § §-§- §
CONTENTS
4 Channels Temp. Controlle
Dire ct operation
Reverse Operation
Heating / Cooling
Refer to inputs sheet
Relay
SSR
TIIAC
Current (4 - 20 mA)
Current (0 - 20 mA)
NONE
Relay
SSr
TRIAC
Current (4 - 20 mA)
Current (0 - 20 mA)
None
AL 2, 3
AL2,3 + RS232 + Contact Input
AL2,3 + RS422/485 + Contact Input
AL 2, 3 + HBA
24 V a.c / d.c (50/60Hz) - Not ready
100- 240 V a.c (50 / 60 Hz)
100 V d.c
2 …‡˜¡
2
- 1. Installation
§§SSuuffffiixx
CCooddee ooff 44 cchhaannnneellss

9
2
-
3.
Rating
Items
Power Voltage
Consumption
Input Ty pe
Display Extent
Effect of Signal Resistance
Effect of Input Resistance
Input Impedance
Allowable Input Voltage
Extent of RJ C
Type of Control
Contact Input
Sampling Cycle
Control Output
Description
100 - 240 V a.c, (50 - 60 Hz) (¡ 10 %)
Maximum 4W
Thermocouple : K, J, R, S, B, E, N, T, W5RE/W26RE, PL2, U, L
RTD : Pt100 § (DIN), Pt100 § (KS/JIS)
Dire ct Voltage : 0 - 5 V, 0 - 10 V, 1 - 5 V
Thermocouple : (¡0.3 % of span + 1 Digit) or ¡  2 ¡  [2¢ ]
Irrespectiv e o f a n y side, Bigger side
RTD : (¡ 0.3 % of span + 1 Digit) or ¡  0.8 ¡  [1.6 ¢ ]
Irrespectiv e o f a n y side, Bigger side
Dire ct Voltage :(¡ 0.3 % of span + 1 Digit)
About   0.2 uV / §
About 0.01 % / § 
About 1 § 
TC, RTD : 5 ~ - 2 V
Vd.c : 12.5 ~ - 5 V
¡ 1.5 ¡  ( 0 ~ 5 0 ¡ ), ¡ 1 ¡ (10 ~ 35 ¡)
Dire ct Control : Down-scale
Reverse Control : Up-scale
On/Off, P, PI, PD, PID Control
Dire ct Control & Reverse Control
On : less than 2 § , Of f : over 15 § 
Relay Output : 250 V a.c, 3A Resistive Load,
Propor tional Time : 0 ~ 100 ms
Time Resolution : 0.1% or 10 ms
Voltage Pulse : Off :less than 0.1V d.c, On: over 12 V d.c
Current Output : Resistive Load : less than 600§,
Extent : ¡ 1 % of span
Triac : (Ambient Te m perature is less than 40 C)
Zero Crossing function.
8
2
- 2. Input Type & Range Code
K
J
R
S
B
E
N
T
W
PL2
U
L
Pt100
JPt100
0-5 V
1-5 V
0-10 V
Input Ty pe R ange Code (¡)Code
K0
K1
J0
J1
R0
R1
S0
S1
B0
B1
E0
E1
N0
N1
T0
W0
A0
U0
L0
D0
P0
V0
V1
V2
-200 ~ 1370
-199.9 ~ 999.9
-200 ~ 1200
-199.9 ~ 999.9
0 ~ 1700
0.0 ~ 999.9
0 ~ 1700
0.0 ~ 999.9
0 ~ 1800
0.0 ~ 999.9
-200 ~ 1000
-199.9 ~ 999.9
-200 ~ 1300
-199.9 ~ 999.9
-199.9 ~ 400.0
0 ~ 2300
0 ~ 1390
-199.9 ~ 600.0
-199.9 ~ 900.0
-199.9 ~ 600.0
-199.9 ~ 500.0
-199.9 ~ 999.9
-199.9 ~ 999.9
-199.9 ~ 999.9

11
2
- 5. Terminal Arrangement
§§CCoonnnneeccttiioonnss
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
2
- 4. Dimentions & Panel Cutout
(Unit : mm)
8 74 26
100
96
96
120
120
91.5+0.8
-0.0 
91.5+0.8
-0.0 
10
Alarm Output
Insulation esistance
Dielectric Strength
Memory Backup
Setting Method
˙¥‰ˆ„‰˜
Others
Operation Condition
Alarm 1, 2, 3 : 250 V a.c, 1 A (Resistive Load)
HBA : Current Transformeter(CT))
0 ~100 A (J&D ELETRONIC. Co., Ltd)
Extent : ¡  5 % o f span or ¡2 A Bigger side
Measure terminal & Power terminal : 20 § in 500 V d.c
Power terminal & Measure terminal : 1 min in 2300 V a.c
Memory by EEPROM
Life span of EEPROM: 100,000 writing possible, Storage data for almost 10 years
¡»Œ„¤»Œ¯¿¡˙˙`¯—…‡`⁄
7……–‚˘fi ¨ LED ˙¥‰ˆ
Zone function, HBA(Heater Break Alarm), Rate function, Input
compensation, Channel
enable, Input filter, Memory, Scan, Auto-tuning, Alarm Output,
Heating/Cooling
Ambient Te m perature : 0 ~ 50 ¡ 
Ambient Humidity : 35 ~ 85 % R.H.(No condensation)

13
§§OOppttiioonn
22((22))--HHBBAA
NO
37
38
39
40
41
42
43
44
45
46
47
48
CT Input
Description
CT2
CT1
COM
CT4
CT3
COM
CT6
CT5
COM
CT8
CT7
COM
§§IInnppuutt
((11)) 11 ~~ 44 CChhaannnneellss
NO
13
14
15
16
17
18
19
20
21
22
23
24
Channel 1
RTD : Resistance
Temperature Detector
T.C :Thermocouple
V d.c : P ower Voltage
Channel 2
RTD : Resistance
Temperature Detector
T.C :Thermocouple
V d.c : P ower Voltage
Channel 3
RTD : Resistance
Temperature Detector
T.C :Thermocouple
V d.c : P ower Voltage
Channel 4
RTD : Resistance
Temperature Detector
T.C :Thermocouple
V d.c : P ower Voltage
Description
+
-
+
-
V d.c
T.C
RT D
+
-
+
-
V d.c
T.C
RT D
+
-
+
-
V d.c
T.C
RT D
+
-
+
-
V d.c
T.C
RT D
+
-
+
-
V d.c
T.C
RT D
+
-
+
-
V d.c
T.C
RT D
+
-
+
-
V d.c
T.C
RT D
+
-
+
-
V d.c
T.C
RT D
§§IInnppuutt
((22)) 55 ~~ 88 CChhaannnneellss
NO
25
26
27
28
29
30
31
32
33
34
35
36
Channel 5
RTD : Resistance
Temperature Detector
T.C :Thermocouple
V d.c : P ower Voltage
Channel 6
RTD : Resistance
Temperature Detector
T.C :Thermocouple
V d.c : P ower Voltage
Channel 7
RTD : Resistance
Temperature Detector
T.C :Thermocouple
V d.c : P ower Voltage
Channel 8
RTD : Resistance
Temperature Detector
T.C :Thermocouple
V d.c : P ower Voltage
Description
§§OOppttiioonn
11((11))--DDII//CCOOMM
NO
37
38
39
40
41
42
43
44
45
46
47
48
Contact Input
(Run/Stop)
Contact Input
(Memory Zone)
Communication
(1)RS-422A / 48 5
(2)RS-232C
Description
DI
DI
DI
DI
DI
1
2
4
SET
COM
RX(+)
SG
TX(+)
TX(-)
SG
TX
RX
RX(-) (1)(2)
12
§§OOuuttppuutt
11
((oouutt
11
~~
44))
NO
1
2
3
4
5
6
7
8
9
10
11
12
L
N
100-220 V a.c Voltage Input
Alarm 1 Output
Output 1
(1) Relay
(2) SSR / Current
(3) Triac
Output 2
(1) Relay
(2) SSR / Current
(3) Triac
Output 3
(1) Relay
2) SSR / Current
(3) Triac
Output 4
(1) Relay
2) SSR / Current
(3) Triac
Description
NO
NO
NO
NO
NO
(1) (2)
+
-
(3)
(1) (2)
+
-
(3)
(1) (2)
+
-
(3)
(1) (2)
+
-
(3)
§§OOuuttppuutt
22 ((oouutt 55 ~~ 88))
NO
49
50
51
52
53
54
55
56
57
58
59
60
Alarm 2 Output
Alarm 3 Output
Output 5
(1) Relay
(2) SSR / Current
(3) Triac
Output 6
(1) Relay
(2) SSR / Current
(3) Triac
Output 7
(1) Relay
(2) SSR / Current
(3) Triac
Output 8
(1) Relay
(2) SSR / Current
(3) Triac
Description
NO
NO
NO
(1) (2)
+
-
(3)
NO
(1) (2)
+
-
(3)
NO
(1) (2)
+
-
(3)
NO
(1) (2)
+
-
(3)

3 Basic Operation
15
3
- 1. Flowchart of Parameter
ALT3
Monitor
ENT + << R/S
ENT + << R/S
ENT 2s
ENT
ENT
ENT
ENT
ENT 2s
Function Mode Setup Mode
ATPV
SV
STOP
<<R/S
RUN
State
STOP
State
SV
BIAS
FILT
CT
FR-H
FR-L
ALT1
ALT2
ADDR
PSL
BPS
PRI
STP
DLN
PRI
RPT
SCAN
LOCK1
LOCK2
Operation Mode
LBA
LBD
AL1
AL2
AL3
PB
TI
TD
AR
RATE
DlSL
CHEN
ENT Memory
Zone
ENT
SV
ZONE
HBC
HBA
14
2
-6. Name & Function
¤ : Window for displaying Channel
(¡A¡–Batch Setting)
¤Ł: Indicate Lamp(Output 1~8,AT)
¤Ø : Window for displaying Memory Zone
(Display M e m o ry Zone)
¤Œ : Key f or changing Channel
¤º : Set ting Key
¤ : Shif t & Re set Key
¤ : Key f or decreasing Set-values(SV)
¤ : Key f or increasing Set-Values(SV)
¤ : Alarm Output Lamp(Alarm 1~3)
¤ : Window for displaying Set-Values
(SV window)
¤æ : window for displaying Pro c ess-Values
(PV window)
NO.
¤
¤Ł
¤Ø
¤Œ
¤º
¤
¤
¤
¤
¤
¤æ
Paramete
rChannel
Display
Output/AT
Memory
Range
CH Key
ENT key
ke y
ke y
ke y
ALM1~3
SV
Window
PV
Window
Description
Monitor screen: Displays the channel of PV/SV currently.
Screen except Monitor: Displays Parameter Channel for setting currently.
Lights Lamp when Output 1~8 is on.
Flicker s La m p w h e n t h e d isplayed channel is in AT currently.
Monitor screen: Displays the number of controlling Zone currently. Scre e n
except Monitor: Displays the number of Parameter Zone for setting currently.
Monitor screen: Press this key for 1 sec to change Auto-scan during
scanning each. Channel to scan is changed by pressing CH Key during scanning
each. Screen except Monitor: Changes the Channel number of Parameter for
setting currently
Saves Parameter changed or turns into the next Parameter.
Monitor screen: Starting or finishing Control by pressing for 1 sec.
Screen except Monitor: Operating by Shif t- Ke y.
Decreases Parameter Values.
Increases Parameter Values.
Lights Lamp when Alarm Output is on.
Monitor screen: Displays Set-Value(SV).
Screen except Monitor: Displays Parameter Value.
Monitor screen: Displays Pro c ess-Value(PV).
Screen except Monitor: Displays Parameter name as an abbreviation.
①
②
⑤ ⑥ ⑦
⑪
⑩
⑨
⑧
③
④
: ZONE Parameter
: Display e d in
Option
If you don¡flt operate any key on the screen of Operation,
Function & Setup for 1 min., it is move d into Monitor scre en.
`˙

1716
This screen is to check Pro cess-Value(PV) & Set-Value(SV) come under Channel
number displaye d on C H window. Channel number is changed by pressing
CH key (Each
Scan), and automatically it is changed by doing CH key for 1 sec. over.(Auto Scan).
Scanned time is decided in¡Scan¡–Parameter in that time.(Refer to¡SCAN¡–in Setup
Mode).
*If SV Rate is operated, Rated SV is displaye d.
*If PV is on stop running, it displays STOP(Refer to 5-1. RUN/STOP). In case of an
error, it displa y s ERROR(Refer to 6-4. Error C ode).
¤ Monitor screen: Displays the channel of PV/SV currently.
Screen except Monitor: Displays Parameter Channel for setting currently.
¤ŁMonitor screen: Displays the number of controlling Zone currently.
Screen except Monitor: Displays the number of Parameter Zone for setting currently.
¤Ø Monitor screen: Displays current Pro cess-Value(PV).
Screen except Monitor: Displays Parameter name as an abbreviation.
¤Œ Monitor screen: Displays Set-Value(SV).
Screen except Monitor: Displays Parameter Value
3 - 3.
Monitor Display
CH
ZONE
PV
SV
①
②
③
④
3 - 2.
Parameter Range & Initial Value
Signal
SV
ZONE
HBC
LBA
LBD
AL1
AL2
AL3
PB
TI
TD
AR
RATE
DISL
CHEN
AT
HBA
BIAS
FR-H
FR-L
ALT1
ALT2
ALT3
FILT
CT
ADDR
PSL
BPS
PRI
ST P
DLN
RPT
SCAN
LOC1
LOC2
Name
Set Value
Memory Zone
Heater Break urrent
Loop Break Alarm
Loop Break Alarm
Deadband
Alarm 1
Alarm 2
Alarm 3
Propor tional B a n d
Time of Integral
Time of
Derivativ e
Anti-Reset Windup
SV rate
DI Select
Channel Enable
Auto-Tuning
Heater Break Alarm
Bias
Range High Limit
Range Low Limit
Alarm 1 ty pe
Alarm 2 ty pe
Alarm 3 ty pe
Filter
Cycle Time
Address
Protocol select
Bits Per Sec o n d
Parity
Stop Bit
Data Length
Response Time
Scan Time
Lock 1
Lock 2
Range
EU(0 ~ 100 %)
1 ~ 8
0.0 ~ 100.0
OFF, 0.1 ~ 200.0
EUS(0 ~ 100 %)
Refer to 5 - 3 Alarm
EU(0 ~ 100 %)
0 ~ 3600
0 ~ 3600
0 ~ 100
EUS(0 ~ 100 %)
0, 1
OFF, MONI, CONT
OFF, ON
OFF, 0.0 ~ 100.0
EUS(0 ~ 100 %)
FR-L~High Limit
Low Limit~FR-H
0 ~ 16
0 ~ 16
0 ~ 16
OFF, 1 ~ 100
1 ~ 100
1 ~ 99
0, 1
0 ~ 3
0 ~ 2
1, 2
7, 8
0 ~ 10
1 ~ 10
Refer To LOC 1
Refer To LO C 2
Initial Value
EU(0 %)
1
0.0
8.0
EUS
(0 %)
30.0 ¡
/3.0 %
240
60
0 (AU TO)
OFF
0
CONT
OFF
OFF
0.0
High Limit
High Limit
0
0
0
OFF
20/2
1
0
3
0
1
8
0
2
Unit
EU
ABS
Ampere
Min
EUS
EU
sec.
sec.
%
EUS
ABS
ABS
Ampere
EUS
EU
EU
sec.
sec.
ABS
ABS
ABS
ABS
ABS
ABS
sec.
ABS
ABS
Area
§
§
¡¿
§
§
§
§
§
§
§
§
§
§
¡¿
§
§
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿
CH
§
§
§
§
§
§
§
§
§
§
§
§
§
¡¿
§
§
§
§
¡¿
¡¿
¡¿
¡¿
¡¿
§
§
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿
¡¿

1918
§ LBA : Control Loop Break Alarm
§§DDeessccrriippttiioonn
ooff eeaacchh ppaarraammeetteerr
Ifyou press ENT key in monitor scre en for 2 sec. , it enters into Function mode.
Generally users create setting value easily on occasion in selecting function mode.
There are functions as follows ; LBA, Alarm 1, Alarm 2, Alarm 3
P, I, D need ed to control,
Rate (In case SV is changed by AR value & Variation of SV)
CHEN(Not displayed a channel not to use)
You can select by ENT key. It is available to re gister and change setting value by using
, , ke y s.
3 - 5.
Function Mode
Initial Value : 1
Setting range : 0.1~200.0 min
Contents : LBA watches variation of PV and set
time to detect any abnormal control loop.
Displaye d in case only LBA is set in
alarm 1.
If At operates, double TI is set
automatically.
No operate in case LBA is Off.
Operation : In case output is 0% and control dire ction
is dir e ct If PV value is not rising over
2C(2F,2%) within setting time in LBA,
it happens. In case output is 0% and
control dire ction is re v erse If PV v alue is
not falling ov er 2C(2F,2%) within setting
time in LBA, it happens. In case output is
100% and control dire ction is dire ct If PV
value is not falling over 2C(2F,2%) within
setting time in LBA, it happens.
In case output is 100% and control
dir e ction is re verse If PV value is not
rising over 2C(2F,2%) within setting time
in LBA, it happens.
CH
ZONE
PV
SV
Set SV & Zone to control. Also you can check HBA value in case of HBA option.
Initial Value : 0 ¡, 0.0 ¡ 
Setting range : Within input range.
Contents : Set SV
Allowable to set 8 SV in maximum
from 1CH to 8CH.
Allowable to set SV as the same value
simultaneously fro m 1CH to 8CH.
3-
4.
Operation Mode
CH
ZONE
PV
SV
Initial Value : 1
Setting range : 1 ~ 8
Contents : Set Memory range(ZONE) to control.
Save Setting value per each channel to
Memory zone in maximum 8(Available to
create Setting value per each channel
8 * 8 Zone =64)
CH
ZONE
PV
SV

2120
§ „”—‰ˆ£ (TD : Derivativ e Time)
Initial Value : 60 sec.
Setting range : 1 ~ 3600 sec.
Contents : Set Derivativ e o p er ation time .
Ifyou operates AT, it is set automatically.
CH
ZONE
PV
SV
§ ”æ•˚·º(PB : Proportional Ba n d )
ON/OFF
: If it set as PB=0, operate ON/OFF control.
§ TI : Inte gral Time
Initial Value : 60 sec.
Setting range : 1 ~ 3600 sec.
Contents : Contents: Set Integral operation time..
Ifyou operates AT, it is set automatically.
CH
ZONE
PV
SV
Initial Value : 30 ¡ , 30.0 ¡ , Voltage input : 3.0 %
Setting range : 0(0.0) ~ •„˛`ˆ·º“
Contents : Set PB to control P, PI, PD & PID.
Ifyou operates AT, it is set automatically.
CH
ZONE
PV
SV
§ LBD : Control Loop Break Alarm Deadband
§ AL 1 : Alarm 1
§ AL 2 : Alarm 2
Initial Value : Voltage input : 0 ¡ , 0.0 ¡ 
Setting range : 0 ~ 100 sec
Contents : Contents: Set all extents except the range
of errors occurre d. Displaye d in case only
LBA is set in alarm 1. Not operated if LBA
setting value is set as¡0¡–.)
CH
ZONE
PV
SV
Initial Value : Maximum value of range
(Refer to Input t y pe & Range code)
Setting range : Range(Refer to Input ty pe & Range code)
Contents : Set the setting value of Alarm 1.
Displaye d in case only LBA is set in
alarm 1. Not displaye d if alarm t y p e is
FAIL or LBA(HBA).
CH
ZONE
PV
SV
Initial Value : Maximum value of range
(Refer to Input t y pe & Range code)
Setting range : Range(Refer to Input ty pe & Range code)
Contents : Set the setting value of Alarm 2.
Displaye d in case only LBA is set in
alarm 2. Not displaye d if alarm ty pe is
FAIL or LBA(HBA).
CH
ZONE
PV
SV
§ AL 3 : Alarm 3
Initial Value : Maximum value of range
(Refer to Input t y pe & Range code)
Setting range : Range(Refer to Input ty pe & Range code)
Contents : Set the setting value of Alarm 3.
Displaye d in case only LBA is set in
alarm 3. Not displaye d if alarm ty pe is
FAIL or LBA(HBA).
CH
ZONE
PV
SV

2322
§ AT : Auto - Tuning
§§DDeessccrriippttiioonn
ooff eeaacchh ppaarraammeetteerr
Ifyou press ENT key + key in the monitor scre en or Function mode, you can enter
into Setup mode.
Generally Setup mode is used when user builds system. There are AT, HBA, BIAS, FILT,
CT, Communication mode parameter, LO C K1 /LOCK2 & etc.
You can register & change Setting value by choosing , , ke y s.
3
- 6. SETUP MODE)
Initial Value : OFF
Setting range : OFF, ON
Contents : Set whether At operates or not.
AT operation : Ifyou press ENT key after AT parameter
is On, AT operates & AT lamp flickers.
AT cancel : AT is cancelle d automatically as follows;
When AT parameter is Off
When SV is changed
Burn-out
When ADC error happens
Running is stopped
When you operate AT of 8 channels
simultaneously, channel parameter
becomes¡1->2->¡ƒ->A¡–by pressing CH
key. When¡A¡–is shown , change Off in
the window SV into On. AT of all
channels operates by pressing ENT key
simultaneously.
When you operates AT in a channel
only, AT is On after yo u c h o ose channel
by pressing CH key.
AT operates in the channel wanted in
that time.
CH
ZONE
PV
SV
§ Rate : SV Rate
§ CHEN : Channel Enable
§ Anti Reset Windup
Initial Value : 0 (Auto)
Setting range : 0 (Auto) ~ 100 %
Contents : Set the range of valid operation in
Inte gr al op er ation to pre vent fro m
overshoot by the effect of over-
inte gr al.
CH
ZONE
PV
SV
§ DISL : DI Select
CH
ZONE
PV
SV
Initial Value : OFF
Setting range : 0 (0.0) ~ maximum range / min
Contents : Set SV variation per min.
If it is Of f, it do e s n ¡ flt operates.
Ifyou change SV in RUN, Rate operates.
Ifyou operate AT during Rate is
operating, Rate is stoppe d at once a nd
AT operates as new SV.
Initial Value : 0
Setting range : 0, 1
Contents : Select whether you use DI function or
now
CH
ZONE
PV
SV
Initial Value : C O N T
Setting range : OFF, CONT, MONI
Contents : Select whether you use each channel
about each Memory zone or not.
OFF : Appoint a channel not used.
Not displaye d a channel display in
setting Of f.
CONT : become normal control condition.
MONI : Displaye d only PV value and Not
operated to control.
CH
ZONE
PV
SV

25
§ FR-L : Range Low Limit
§ ALT1 : Alarm 1 ty pe
§ ALT2 : Alarm 2 ty pe
§ ALT3 : Alarm 3 ty pe
Initial v alue : Lower of input range
Setting method : Set the lower of input ~ FR-H
Contents : Set Lower value of input range.
If input value is lower than this one,
-OVR or bout happens.
CH
ZONE
PV
SV
Initial v alue : 0
Setting range : 0 ~ 16
Contents : Set t y p e of Alarm 1
Refer to 5-3 Alarm
CH
ZONE
PV
SV
Initial v alue : 0
Setting range : 0 ~ 16
Contents : Set t y p e o f Alarm 2.
Refer to 5-3. Alarm.
CH
ZONE
PV
SV
Initial v alue : 0
Setting range : 0 ~ 16
Contents : Set t y p e o f Alarm 3.
Refer to 5-3. Alarm.
CH
ZONE
PV
SV
24
§ HBA : Heater Break Alarm 1
§ BIAS : PV Bias
§ FR-H : Range High Limit
Initial Value : OFF
Setting range : 0.0 ~ 100.0 A
Contents : If you choose HBA option & Alarm ty pe,
you can know Current value in detected
in HBC of operation mode.
Set HBA value as 85% of Current load.
HBA can¡flt be used in case of Current
output. Set HBA SV a little bit lower
when variation of p ower supply is big.
Current detection extent : ¡ 5 % of span
Current detection resolution: 0.5 A
Detection method: Detect Heater Current
af ter output is On(200ms). If On time(CT*
output %) is less than 200ms, it doe s n¡flt
proce e d detection operation. Detection
operation : When HBA value is bigger
than HBC value after detection is
finished, Alarm operates.
CH
ZONE
PV
SV
Initial v alue : 0 ¡, 0.0 ¡ , Voltage input 0.0 %
Setting range : EUS (0 ~ 100 %)
Contents : If measure d value is dif ferent fro m
standard value as sensor co m pensation
function, it is the function to meet by
co mpensating as the amount of deviation.
CH
ZONE
PV
SV
Initial v alue : Upper of input range
Setting range : Upper of input range in FR-L~
Contents : Set upper value in the input range for
user. If input value is higher than this
one, OVR or bout happens.
CH
ZONE
PV
SV

27
§ STP : Stop Bit
§ DLN : Data Length
§ RPT : Response Time
Initial v alue : 1
Setting range : 1 ~ 2
Contents : Set Communication Stop Bit.
Ifcommunication option is chosen,
Parameter is displaye d
CH
ZONE
PV
SV
Initial v alue : 7
Setting range : 7 ~ 8
Contents : Set Communication Data Length. .
Ifcommunication option is chosen,
Parameter is displaye d
CH
ZONE
PV
SV
Initial v alue : 0
Setting range : 0 ~ 10
Contents : Set Communication Response Time.
Ifcommunication option is chosen,
Parameter is displaye d. Response
time = Processing time+ RPT * 20ms
CH
ZONE
PV
SV
§ PRI : Parity
Initial v alue : 0
Setting range : 0 ~ 2
Contents : Set Communication Parity
Ifcommunication option is chosen,
Parameter is displaye d
CH
ZONE
PV
SV
26
§ Filter
§ ADDR : Address
§ BPS : Bits per Sec o n d
Initial v alue : OFF
Setting range : 0 ~ 120 s
Contents : Set the first time of delaye d filter to
remove any noise in the measured input
value.
CH
ZONE
PV
SV
§ CT : Cycle Time
Initial v alue : Relay 20 s, SSR & TRIAC : 2 s
Setting range : 1 ‘~ 100 s
Contents : Set the cycle of control output.
Set output cycle in case of Relay,
Pulse & Triac output. It is not applie d in
case of Current output.
CH
ZONE
PV
SV
Initial v alue : 1
Setting range : 1 ~ 99
Contents : Ifcommunication option is chosen,
Parameter is displaye d.
It is appointed address of instrument in
case of RS232/485/422 communication.
Refer to Communication manual in detail.
CH
ZONE
PV
SV
Initial v alue : 0
Setting range : 0. 1
Contents : Set t y p e o f Communication Protocol
0 : pc link sum None
1 : pc link sum Existed
CH
ZONE
PV
SV

4 Setting Method
29
§§SSVV
vvaalluuee sseettttiinngg mmeetthhoodd
There are some examples to change SV. Others are applied as same method.
Ifyou want SV value to change CH¡–1¡ –in Zo n e ¡1¡ –from 0C to 300C, please setup as
following a proce dure .
§§WWhheenn
yyoouu iinnccrreeaassee SSVV vvaalluuee(( CChhaannggiinngg 339999 ttoo 440000))
§ Press key to flicke r Number of 9 unit like Figure [A] once.
Press key to change into¡0¡–once.
Changed into 400 in the window of SV display like a figure below.
Figure [A] Figure [B]
Pressing ENT button once in PV/SV display m ode,
SV setting mode is displaye d like a figure of the lef t side.
4
- 1. Setting each Channel
And then make 3 By pressing key. Pressing ENT key again, 300 is re gistere d in
setting above. Doing ENT key one more, it is moved on the range of Zone Memory.
Ex) 0<-0<-0<-0<-0 Whenever you push key, digit of SV is move d like a figure
with flickering operation. Set by using , ke y in sequence of numbers wanted.
Ifyou press button once,¡0¡–of the first SV is
flick e r e d. If y o u p r ess button
again,¡00¡–is flick er e d and then do once more 0 of
¡000¡–is flick er e d.
CH
ZONE
PV
SV
CH
ZONE
PV
SV
CH
ZONE
PV
SV
CH
ZONE
PV
SV
28
§ Æ–˜¡1(LOC1 : Lock 1)
§ Æ–˜¡2(LOC2 : Lock 2)
Initial v alue : 0000
Contents : It is an equipment to limit a change of
parameter setting by controlling ke y.
DIGIT 1 : Prohibited the setting of all
parameters except SV, Alarm1,
Alarm2 & Alarm3.
0: Cancellation 1: Lo c k
DIGIT 2: Prohibited the setting of Alarm1,
Alarm2 & Alarm3.
0: Cancellation 1: Lo c k
DIGIT 3: Prohibited the setting of SV.
0: Cancellation 1: Lo c k
DIGIT 4: Not used(Fixed¡0¡–)
CH
ZONE
PV
SV
Initial v alue : 0
Setting range : 0 ~ 10
Contents : It is an equipment to limit prohibition of
RUN/STOP & Zone change.
DIGIT 1: Prohibited a change of
RUN/STO P
DIGIT 2: Prohibited a change of Zon e
DIGIT 3: Not used (Fixed ¡0¡–)
DIGIT 4: Not used(Fixed¡0¡–)
CH
ZONE
PV
SV
§ ˙¥‰ˆ£‰ˆ£ (SCAN : Scan Interval Time)
Initial v alue : 2 s
Setting range : 1 ~ 100 s
Contents : Set time until current displaye d channel
is changed into next channel.
CH
ZONE
PV
SV

31
Pressing CH key to change Num. ¡1¡ –into ¡2¡–in channel
number, Num.¡1¡ –is changed into Num.¡2¡–
CH
ZONE
PV
SV
Pressing ENT key in the window of PV/SV display once,
it is shown like the left figur e.
CH
ZONE
PV
SV
Pressing key in the lef t figur e t o change Zone number,
Zone value is changed.
CH
ZONE
PV
SV
Pressing key to change 200 into 100 in SV of Num. ¡2¡–
three times. It is flickere d in 100 by doing V key once.
Pressing key once, 200 is changed into 100 and it is
flick er e d i n that time. And then Flickering operation is
stopped & registere d by doing ENT key.
CH
ZONE
PV
SV
Whenever you press key to change Zone from Num. 1 to
Num.2, digit of SV is displaye d in sequence as below. If
cursor is come to Num.¡1¡ –of Zone, Num¡1¡ –is flick er e d.
Pressing ^ key once in that time, ¡1¡ –is changed into ¡2¡–.
Doing ENT key, a flickering operation of Num. ¡2¡–is
stopped.
1 ¤B 0 ¤B 0 ¤B 0 ¤B 0 ¤B
CH
ZONE
PV
SV
30
§§WWhheenn
yyoouu ddeeccrreeaasseedd SSVV vvaalluuee(( CChhaannggiinngg 440000 ttoo 339900))
§ Press key to flicke r Number of 10 unit like Figure [A] twice.
§ Press key to change¡0¡–of 10 unit into¡9¡–once.
§ Changed into 390 in the window of SV display like a figure below.
§§WWhheenn
yyoouu sseett aa vvaalluuee iinn ((--))(( CChhaannggiinngg 110000 ttoo --110000))
§ Press key once to flicke r Number 9 of unit like Figure [A] thre e times
§ Press key to change into¡0¡–twice.
§ Changed into -100 in the window of SV display like a figure below.
§§WWhheenn
yyoouu cchhaannggee SSVV ooff aannootthheerr ZZoonnee wwiitthhoouutt cchhaannggiinngg ccuurrrreenntt ccoonnttrrooll
ZZoonnee..
Current control Zone is Zone 1, and changeable Zone is Zone 2. in case of changing
SV from 200 to 100 in the channel 2 of Zone 2.
Figure [A] Figure [B]
CH
ZONE
PV
SV
CH
ZONE
PV
SV
Figure [A] Figure [B]
CH
ZONE
PV
SV
CH
ZONE
PV
SV
Pressing ENT key in the window of PV/SV once, it is
displayed like the lef t figure.
CH
ZONE
PV
SV

33
5 Explanation of Functions
§ Without DI OPTION
ƒƒUUIInn
PPVV//SSVV ssccrreeeenn,, yyoouu ccaann cchhaannggee RRUUNN ¡¡ŒŒSSTTOOPP bbyy pprreessssiinngg kkeeyy..
ƒUIn case of STOP,¡ ¡–will b e displaye d on PV window.
§ With DI OPTION
ƒURUN/STOP DI(Terminal No.37-38) will be connected. By pressing key, it star ts to
run on PS/SV screen.
¡ When RUN/STOP DI is disconnected, it stops running and¡ ¡–will b e displaye d.
¡ When it stops running by means of key,¡ ¡–will show up.
¡ When it stops running by means of DI and Key simultaneously,¡ ¡–will
show up.
§§CCOONNTTRROOLL
ZZOONNEE CCHHAANNGGEE
§ Without DI OPTION
ƒUAccording to Zo n e¡fls value, Control Zone will be decided.
§ With DI OPTION
ƒU According to Zo n e¡ fls value, Control Zone will be changed. In addition, you can
change ZONE according to ZONE DI(Terminal No. 39-43). How to change ZONE
through DI : Firstly sele ct ZONE as terminal no. 40-42. After that you can list ZO N T
by connecting terminal no. 39-43.
§§AAuuttoo--ttuunniinngg
Auto-Tuning calculate the most suitable PID and LBA value automatically and set yp PID
and LBA value into each parameter.
§ START Auto-Tuning
ƒUPlease select all parameters except for PID/LBA.
ƒULock level 1 & Lo ck level 2 should be set up as¡0000¡–.
ƒURUN/STOP should be selected to RUN mode.
¡¿ : OPEN, - : COSED
Terminal
NO.
39 - 40
39 - 41
39 - 42
1
¡¿
¡¿
¡¿
2
-
¡¿
¡¿
3
¡¿
-
¡¿
4
-
-
¡¿
5
¡¿
¡¿
-
6
-
¡¿
-
7
¡¿
-
-
8
-
-
-
39
40
41
42
43
ZONE
5 -
1. RUN/STOP
32
§§WWhheenn
yyoouu sseett aallll SSVV aatt tthhee ssaammee ttiimmee[[¡¡AA¡¡––]]
Set SV in channel 1~8 from 0C to 200C at the same time.
Pressing ENT key in the window of PV/SV display, it is
displayed like the lef t window.
Press CH key. Character ¡A¡–is displa ye d n e xt to number in
the window CH display and¡----¡ is displaye d in the window
of SV display.
CH
ZONE
PV
SV
Character¡A¡–means colle ctiv e s e t ting.
Whenever you press CH key, channel number is changed as
follows;
1-2-3-4-5-6-7-8-A
CH
ZONE
PV
SV
Cursor is move to the position of 100 unit by pressing key
and 200 is set by pressing key twice. If you press ENT key,
SV values of all channels are re gistere d a s 2 0 0
simultaneously. Parameter is changed into the next parameter.
CH
ZONE
PV
SV
If this pro c e d u re is finished, SV of channel not used beco m e
colle ctiv e s et ting.
Caution

35
Alarm will act as a¡OR¡–condition against all channels.
(* OR condition : If any channel out of total 8 channels exce ed ed alarm setting value,
alarm output happe n ed )
¡ Hysterisis against alarm is set up as¡ 2 ¡
¡ When setting Wait Alarm, in the below mentioned occasion, waiting movements will
be operated.
In case of starting operation for the first time.
In case of changing set value
Set Value was changed due to the change of zone.
ƒUInitial
Value & Setting Range in accordance with Alarm Type
5
- 3. ALARM
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Alarm No Alarm Ty pe Initial Value Setting Range
No Alarm
Upper limit Alarm hysterisis
Lower limit Alarm hysterisis
Upper & Lower limit Alarm hysterisis
Alarm within it range
Upper limit hy sterisis hold alarm
Lower limit hysterisis hold alarm
Upper&Lower limit hysterisis hold alarm
Hold alarm within range
Absolute upper limit alarm
Absolute lower limit alarm
Absolute upper limit hold alarm
Absolute lower limit hold alarm
SV upper limit alarm
SV lower limit alarm
LBA/HBA Alarm
FAIL alarm
-
EUS (100 %)
EUS (100 %)
EUS (100 %)
EUS (0 %)
EUS (100 %)
EUS (100 %)
EUS (100 %)
EUS (0 %)
EU (100 %)
EU (0 %)
EU (100 %)
EU (0 %)
EU (100 %)
EU (0 %)
-
-
-
EUS (-100~ 100 %)
EUS (-100~100 %)
EUS (0 ~ 100 %)
EUS (0 ~ 100 %)
EUS (-100 ~ 100 %)
EUS (-100 ~ 100 %)
EUS (0 ~ 100 %)
EUS (0 ~ 100 %)
EU (0 ~ 100 %)
EU (0 ~ 100 %)
EU (0 ~ 100 %)
EU (0 ~ 100 %)
EU (0 ~ 100 %)
EU (0 ~ 100 %)
-
-
¡ Ifyou select in Alarm No. 15 in ALT1, LBA Alarm will operate. If y o u select in
Alarm No. 15 in ALT2,3, HBA alarm will operate.
¡ HBA alarm could be operated only in case output ty pe is RELAY or SSR output.
¡ You can select within its set ting range : -1999 ~ 9999
34
§ ‰˙˙
§ Cancel Auto-Tuning
If the below conditions happe n ed, Auto-Tuning will be cancelle d.
ƒU Burn-out or ADC error on account of bro ken sensor input cable.
ƒU Auto-Tuning parameter was OFF during Auto-Tuning.
ƒU In case of Power Off
ƒU In case of changing into RUN/STO P m ode.
After finishing Auto-Tuning, changed parameters are PB,AR,TI,TD and LBA. If AT is
cancelle d, c ontroller will b e back to the previous PID and LBA value and it starts
control. Af ter Auto-Tuning, If control is not working smoothly, please adjust value of
PID integra l number to meet suitable controller ¡ fls value.
This function is used when you want to set same value up from channel 1 to channel 8
in the designated zone.
1 -> 2 -> 3 -> 4 -> 5 -> 6 -> 7 -> 8-> A
¡A¡–will b e shown om CH display window,¡----¡ will b e shown on SV window. At
this time, please set set-value up by , , key. If you press ENT key, same
value will be set up from channel 1 to channel 9.
Ifyou press key, parameter which can operate
Auto-Tuning will show up as left picture.
CH
ZONE
PV
SV
Ifyou press key one time, key turns on and off a light.
In this time, if your press¡ ¡–key it stops turning on and off
a light and then AT ramp will turn on and off a light.
CH
ZONE
PV
SV
5
-
2. Batch Setting

37
§§AAllaarrmm
hhyysstteerriissiiss
High alarm
Low alarm
Alarm type Alarm operation
High temp.
Low temp.
SV
ON OFF
HYS
ALM
High temp.
Low temp.
SV
ONOFF
HYS
ALM
§§AAllaarrmm
wwaaiittiinngg ooppeerraattiioonn
No
waiting
operation
Waiting
operation
Alarm type Alarm operation
Waiting operation
deviation
SV
ALM
OFFOFF ON
PV
SV
ALM
ON OFF ON
PV
No Waiting operation
deviation
Low SV
alarm
High SV
alarm
High temp.
Low temp.
SV
ONOFF
High temp.Low temp.
ON OFF
SV
36
High
deviation
alarm
§ Alarm operation
¡⁄High¡⁄Low deviation alarm
Alarm type Alarm operation
High temp.
Low temp.
ALMSV
ONOFF
High¡⁄Lo w
deviation
alarm value
Alarm
within
range
High
absolute
alarm
High temp.
Low temp.
SV
ONON OFF
ALMALM
High temp.
Low temp.
ALM
ONOFF OFF
SV ALM
High temp.
Low temp.
ALM
ONOFF
Lo w
deviation
alarm
High temp.
Low temp.
SV
ON OFF
ALM
High temp.
Low temp.
ON OFF
ALM
Lo w
absolute
alarm