Happy Beds Aurora Ottoman Bed User manual

Aurora Ottoman Bed - 5ft
& 6ft
Assembly Instructions
www.happybeds.co.uk
Important before assembly:
Health & Safety:
.
Read these instructions carefully before assembling or using the product.
Please check the contents of the boxes before attempting to assemble this product. The instructions will
have a checklist of parts and fittings.
Assemble the product as close to its intended final location/room as possible.
This product or some parts of this product will be heavy. Please use an assistant when lifting.
Please keep small parts out of reach of children.
Always use on a level, even surface.
DO NOT jump on the product or any of its parts.
DO NOT use this product if any parts are missing, damaged or worn.
DO NOT use this product unless all fixings are secured.
Further instructions are on the following pages.
Please keep these instructions for future reference.

@
This product or some parts of this product will be heavy. Please use an assistant when lifting.
Never drag or push the pieces across a hard or stone floor as this will cause damage to the
joints. Use a carpet or a rug for extra care.
If you have problems assembling or have damaged or missing pieces, please contact our
customer services (details at the back of these instructions)
(Not metal)
These tools are not
necessary, but may help
to assemble the product.
Do NOT use any power
tools as this may
damage the frame.

J
A
O
O
BC
C
D
G
H
J
K
L
LM
M
M
J
J
IE
E
Page 3 of 10
H
No Hardware List Qty Box
1 JCBB M6 x 20mm 8 pcs
2 JCBB M6 x 35mm 8 pcs
3 JCBC M6 x 45mm 12 pcs
4 JCBC M6 x 80mm 2 pcs
5 JCBB M8 x 20mm 20 pcs
6 JCBB M8 x 40mm 14 pcs
7 JCBB M8 x 45mm 6 pcs
8 M8 Spring Washer 6 pcs
9 M6 Flat Washer 8 pcs 3
10 M8 Flat Washer 14 pcs
11 M6 Hex Nuts 18 pcs
12 M8 Hex Nuts 6 pcs
13 Allen Key M4 1 pc
14 Allen Key M5 1 pc
15 M6 Spanner 1 pc
16 M8 Spanner 1 pc
17 Plastic Washer 4 pcs
18 L-Shape Metal Corner Bracket 2 pcs 4
F
No Part List Qty Box
A Headboard 1 pc 1
B Footboard 1 pc 2
C Side Rail 2 pcs 3
D Metal Bed Base Frame 1 set
E U-bracket 2 pcs
F Base Handle 2 pcs
4
G Hydraulic Base Support 2 pcs
H Hydraulic Pump 2 pcs
I Support Bed Base Leg 1 pc
J Bottom Bed Base 4 pcs 5
K Cross Bar I 1 pc
L Cross Bar II 2 pcs 4
M Support Cross Bar Leg 3 pcs
N Bed Base Support Rail 2 pcs 3
O Headboard Wing 2 pcs
P Leg 4 pcs 4
N
N
P
P
P

Step 1:
To fix the support bed base (N) to the footboard (B) you will need to use hardware parts 3 with the M4 allen key (13).
To fix the leg (P) in to the headboard (A) and footboard (B).
Page 4 of 10
3 JCBC M6 x 45mm 4 pcs
13 Allen Key M4 1 pc
17 Plastic Washer 4 pcs
Step 2:
To fix the left side rail (C) and right side rail (C) to the headboard (A) and footboard (B) you will need to use hardware
parts 5 with the M5 allen key (14).
5 JCBB M8 x 20mm 12 pcs
14 Allen Key M5 1 pc
Do Not Use Power Tools
A
B
N
N
P
P
P
P
A
B
C
C
2x C
B5
14
A
C
5
14
2x
4x A B
P
133
17
4x
Side View
Bottom View Back View
B
N
Back View

14
5
CB
18
Step 3:
To assembler the cross bar I (K), II (L) you will need to use hardware parts 2 with the M4 allen key (13).
To assembler support cross bar leg (M) after cross bar I, II completed.
Step 4:
To fix the cross bar I (K), II (L) to the footboard (B), side rails (C), you will need to use hardware parts (1) and the M4
Allen Key (13).
To attached the L Shape Metal Corner Bracket (18) to the footboard (B) and side rails (C) you will need to use hardware
parts (5) with the M5 Allen Key (14).
Page 5 of 10
1 JCBB M6 x 20mm 8 pcs
5 JCBB M8 x 20mm 8 pcs
13 Allen Key M4 1 pc
14 Allen Key M5 1 pc
18 L-Shape Metal Corner Bracket 2 pcs
Do Not Use Power Tools
Top View
Side View Side View
Top View
Top View
Side View
K L
L
M
M
M
11 152
13
K L
L
M
13
2
15
11
L
L
KL
A
13L
B
13L
2x
B C
C
A
18
K
11
Back View
A Top End B Bottom End
FB
C
13K
2x 1
HB
FB
HB
2 JCBB M6 x 35mm 8 pcs
11 M6 Hex Nuts 8 pcs
13 Allen Key M4 1 pc
15 M6 Spanner 1 pc

16
10 6 14
C G
H
G
16H
G
2x 2x
2x
Step 5:
To install Hydraulic (H) to the Hydraulic Base Support (G), you will need to loose out the M8 HEX nut from the part (G).
After the part (H) go inside the position, put back the M8 HEX Nut and tighten it using M8 Spanner (16).
To install the complete set of (G) to the left and right side rail (C), you will need to use hardware 6 and 8 with Allen key
M5 (14).
To assemble part G, it is a must to make sure the hole go into the right position as shown in (NOTE). And before
tighten the screw, please make sure part G is in same alignment in between left and right side rail.
DO NOT use any power tools as this may damage the bed frame and will invalidate any claims.
Page 6 of 10
* Please insert the screw end to right hand side.
6 JCBB M8 x 40mm 8 pcs
10 M8 Flat Washer 8 pcs
14 Allen Key M5 1 pc
16 M8 Spanner 1 pc
Side View
H
G
C
C
Do Not Use Power Tools
Side View Side View

2x
E
2x F
D
D
I
I
D
2x F
D
11
3
15
4
11
15
13
13
Step 6:
To assemble part D, it is a must to make sure the hole go into the right position as shown in (NOTE). And before tighten
the screw, please make sure part G is in same alignment in between left and right side of part G.
DO NOT use any power tools as this may damage the bed frame and will invalidate any claims.
Page 7 of 10
D
E
E
3 JCBC M6 x 45mm 8 pcs
4 JCBC M6 x 80mm 2 pcs
9 M6 Flat Washer 8 pcs
11 M6 Hex Nuts 10 pcs
13 Allen Key M4 1 pc
15 M6 Spanner 1 pc
Do Not Use Power Tools
Side View
Top View
9

G
2x
12
16
Step 7:
To assemble part D, it is a must to make sure the hole go into the right position as shown in (NOTE). And before tighten
the screw, please make sure part G is in same alignment in between left and right side of part G.
DO NOT use any power tools as this may damage the bed frame and will invalidate any claims.
Page 8 of 10
* Please insert the screw balance in the middle of the hole.
D
G
14
7
D
Do Not Use Power Tools
7 JCBC M8 x 45mm 6 pcs
12 M8 Hex Nuts 6 pcs
14 Allen Key M5 1 pc
16 M8 Spanner 1 pc
Top View

B
A
J
Step 8:
To put the 4 X BOTTOM PANEL (J), you will need to slightly raise up the beds from the footboard (B) and slot in the
panel go direct to the headboard and continue the second pieces there after the first pieces was in right position.
To assembler the wing (O) you will need to open the velco behind the headboard (A) as shown.
DO NOT use any power tools as this may damage the bed frame and will invalidate any claims.
Page 9 of 10
WARNING:
Take care when assembling the base, assemble the ottoman as closed to its final position. The Ottoman has a
powerful mechanism and after assembly should only be closed and opened when the mattress is in place.
COMPLETE
J
J
A
J
J
A
10
8
614
6x
Back View
O
O
O
6 JCBC M8 x 40mm 6 pcs
8 M8 Spring Washer 6 pcs
10 M8 Flat Washer 6 pcs
14 Allen Key M5 1 pc

@happybeds
w w w . h a p p y b e d s . c o . u k
Important for Ottoman and other gas lift beds
Please follow these final steps to ensure the best experience with your new bed
•Please ensure the pistons are fitted to the bed frame.
•Please place the mattress on top of the bed frame.
•Standing at the foot of the frame (looking at the headboard) open the base and the press
quite forcefully down on the mattress - please do not attempt to do this without the
mattress being in place.
•Please do not pull on the strap handles.
•Please note as the pistons are full of gas - you will need to press heavily to release the
compressed gas.
•Once done the pistons should start operating as normal.

www.happybeds.co.uk
General Care & Maintenance
Please dispose of all packaging safely.
Wipe clean with a slightly damp cloth.
Avoid the use of all household cleaners and abrasives.
Periodically check all screw & fixings to ensure they are secure.
When moving your product, carefully lift into place. Never drag or push the product across the floor as
this will cause damage to the joints. If the product is used on hard flooring, such as wood or laminated
floor, you must place some protection under the legs to stop the product from moving. If this is not
adhered to, it could result in failure to the product that will invalidate the warranty.
For more information on cleaning and product care visit:
https://www.happybeds.co.uk/help-and-advice
In the unlikely event that you have problems putting this product together or have damaged or
missing parts, please contact us by visiting:
https://www.happybeds.co.uk/customer-service
Notes