Happy Beds Sienna Ottoman Storage Bed 4ft User manual

Sienna Ottoman Storage Bed
4ft
Assembly Instructions
www.happybeds.co.uk
Important before assembly:
Read these instructions carefully before assembling or using the product.
Please check the contents of the boxes before attempting to assemble this product. The instructions will
have a checklist of parts and fittings.
It would be sensible to lay a rug or a carpet on the floor where you intend to assemble the product,
to void scratches and damaging the product or the floor.
Assemble the product as close to its intended final location/room as possible.
Do NOT use any power tools as this may damage the frame.
Health & Safety:
This product or some parts of this product will be heavy. Please use an assistant when lifting.
DO NOT jump on the product or any of its parts.
DO NOT use this product if any parts are missing, damaged or worn.
DO NOT use this product unless all fixings are secured.
Please keep small parts out of reach of children.
Always use on a level, even surface.
Please keep these instructions for future reference.

@
This product or some parts of this product will be heavy. Please use an assistant
when lifting.
Never drag or push the pieces across a hard or stone floor as this will cause
damage to the joints. Use a carpet or a rug for extra care.
If you have problems assembling or have damaged or missing pieces, please
contact us by visiting:
https://www.happybeds.co.uk/customer-service
(Not metal)
These tools are not
necessary, but may
help to assemble
certain parts of the
product.
Do NOT use any power
tools as this may
damage the frame.

Page 3 of 8
Box 1
A. Headboard (x1)
Box 2
B. Side Rails (x2) C. Centre Support Rail (x1)
Box 3
F. Footboard (x1) G. Support Leg (x1) H. Slats (x26) I. Legs (x4) J. M8x30mm Bolts (x8) K. Nuts (x16)
M. Flat Washer (14) N. Spring Washer (x14) O. M5 Allen Key (x1) P. Spanner (x1)
QSlat Caps (x26) R. Centre Slat Caps (x13) S. M8x40mm Bolts (x4) T. Bed Cross Bar (x1) U. Pull Strap (x1)
VWoven Fabric (x1) W. Front and Back Frame Rail (x2)
D. Left & Right Frame Rail (x2)
X. Cross Support Bar (x2) YM6x16mm Bolts (x2)
L. M8x45mm Bolts (x18)
E. Hydraulic Part (x2)
All fittings are stored within the zipped compartment of the headboard.

Page 4 of 8
Step 1
Unpack all components from the boxes and check you are not missing anything. Please check these against the list on
page 3 & 4. Should you identify any missing components, please contact the retailer you purchased the bed from.
Box 3
Cont...
Z. M8x16mm Bolts (x4) A1. M8x65mm Bolts (x4) B1. Baton (x2) C1. M4 Allen Key (x1)

Page 5 of 8
Step 3
Attach 2x Side Rails (B)to1x Headboard (A)and1x Footboard (F)using 8x M8x30mm Bolt (J), 8x Spring Washer (N), 8x
Flat Washer (M)and1x M5 Allen Key (O).
Step 2
Attach 2x Legs (I)to the 1x Headboard (A)and then attach 2x Legs (I)to the 1x Footboard (F). Please do not use any
power tools for this assembly as it will void your guarantee.
I
J
M
N
O

Page 6 of 8
Step 4
Attach 2x Hydraulic Part (E) and Baton (B1) to 1x Headboard (A)and1x Footboard (F) using 6x M8x45mm Bolts (L), 6x
Spring Washer (N) and6x Flat Washer (M). Then attach 1xCross Bar (T) to2x Side Rail (B) using 2x M6x16mm
Bolts (Y) and1x M4 Allen Key (C1).
Step 5
Attach the Attach the 2x Front and Back Frame Rails (W)tothe 2x Left & Right Frame Rail (D)using 4x M8x16mm Bolts (Z)
and1x M5 Allen Key (O). Then attach the Centre Support Rail (C)tothe 2x Left & Right Frame Rail (D)using 6x M8x45mm
Bolts (L), 6x Nuts (K), 1x M5 Allen Key (O)and1x Spanner (P)..
W
W
Z O
C
O L
K
P
D
D
E
L
N
M
C1

Page 7 of 8
Step 6
Attach the Centre Support Leg (G)to the Centre SupportRail (C)using 6x M8x45mm Bolts (L), M5 Allen Key (O), 6x Nuts (K)
and1x Spanner (P).
KG
P
OL
Step 7
Attach the Metal Frame (MF)to the 2x Hydraulic Part (E)using 6x M8x45mm Bolts (L), M5 Allen Key (O), 6x Nuts (K)and1x
Spanner(P). Then attach the 2xCross Support Bar (X) tothe Left and Right Frame Rail (D) using 4x M8x65mm Bolts (A1), M5
Allen Key (O), 4x Nuts (K) and1x Spanner (P).
D
L
O
P
P
DO
A1
K
C
MF

Page 8 of 8
Step 9
Turn the bed frame over on to its side andattach the Woven Fabric (V)tothe base of the bed frame as shown below.
V
Step 8
Slot each Slat Cap (Q)on tothe end of each Slat (H). Then slot each Slat (H) intoeach Centre Slat Cap (R) Press firmly
intoeach Metal Rail located on the Metal Frame (MF) andthen intothe Centre Support Rail (C). Finally, attach Pull
Strap () tothe Left or Right Frame Rail () by placing beneath the Metal Frame (MF) and pulling through the inside of
the frame andto form a knot on the outer frame.
N
F
F
MF
O
C

www.happybeds.co.uk
General Care & Maintenance
Please dispose of all packaging safely.
Wipe clean with a slightly damp cloth.
Avoid the use of all household cleaners and abrasives.
Periodically check all screw & fixings to ensure they are secure.
When moving your product, carefully lift into place. Never drag or push the pieces across the
floor as this will cause damage to the joints and could result in failure to the product that will
invalidate the warranty.
For more information on cleaning and product care visit:
https://www.happybeds.co.uk/help-and-advice
We’ve tried to make this product as easy to assemble as possible. In the unlikely event that
you have problems putting it together or have damaged or missing pieces, please contact
us by visiting:
https://www.happybeds.co.uk/customer-service
Notes