Happy Beds Brandon 4FT6 Ottoman Bed User manual

Title of Product
Assembly Instructions
www.happybeds.co.uk
Important before assembly:
.
Health & Safety:
.
Read these instructions carefully before assembling or using the product.
Please check the contents of the boxes before attempting to assemble this product. The instructions will
have a checklist of parts and fittings.
It would be sensible to lay a rug or a carpet on the floor where you intend to assemble the product, to avoid
scratches and damaging the product or the floor.
Assemble the product as close to its intended final location/room as possible.
Do NOT use any power tools as this may damage the frame.
This product or some parts of this product will be heavy. Please use an assistant when lifting.
Please keep small parts out of reach of children.
Always use on a level, even surface.
DO NOT jump on the product or any of its parts.
DO NOT use this product if any parts are missing, damaged or worn.
DO NOT use this product unless all fixings are secured.
Please keep these instructions for future reference.
Brandon 4FT6 & 5FT Ottoman Bed

@
This product or some parts of this product will be heavy. Please use an assistant
when lifting.
Never drag or push the pieces across a hard or stone floor as this will cause
damage to the joints. Use a carpet or a rug for extra care.
If you have problems assembling or have damaged or missing pieces, please
contact us by visiting:
https://www.happybeds.co.uk/customer-service
(Not metal)
These tools are not
necessary, but may
help to assemble
certain parts of the
product.
Do NOT use any power
tools as this may
damage the frame.

J
A
BC
C
D
G
H
J
K
L
LM
M
M
N
J
J
IE
E
Page 3 of 10
H
No Hardware List Qty Box
1 JCBB M6 x 16mm 8 pcs
2 JCBB M6 x 35mm 8 pcs
3 JCBC M6 x 45mm 16 pcs
4 JCBC M6 x 80mm 2 pcs
5 JCBB M8 x 20mm 20 pcs
6 JCBB M8 x 40mm 8 pcs 3
7 JCBB M8 x 45mm 6 pcs
8 M8 Flat Washer 8 pcs
9 M6 Hex Nuts 18 pcs
10 M8 Hex Nuts 6 pcs
11 Allen Key M4 1 pc
12 Allen Key M5 1 pc
13 M6 Spanner 1 pc
14 M8 Spanner 1 pc
15 L-Shape Metal Corner Bracket 2 pcs 4
F
No Part List Qty Box
A Headboard 1 pc 1
B Footboard 1 pc 2
C Side Rail 2 pcs 3
D Metal Bed Base Frame 1 set
E U-bracket 2 pcs
F Base Handle 2 pcs
4
G Hydraulic Base Support 2 pcs
H Hydraulic Pump 2 pcs
I Support Bed Base Leg 1 pc
J Bottom Bed Base 4 pcs 5
K Cross Bar I 1 pc
L Cross Bar II 2 pcs
M Support Cross Bar Leg 3 pcs
N Bed Base Support Rail 4 pcs
O Leg 4 pcs
N
N
O
O
O
3
4

Step 1:
To fix the support bed base (N) to the headboard (A) and footboard (B) you will need to use hardware parts 3 with the
M4 allen key (11).
To fix the leg (O) in to the headboard (A) and footboard (B).
Page 4 of 10
3 JCBC M6 x 45mm 8 pcs
11 Allen Key M4 1 pc
Step 2:
To fix the left side rail (C) and right side rail (C) to the headboard (A) and footboard (B) you will need to use hardware
parts 5 with the M5 allen key (12).
5 JCBB M8 x 20mm 12 pcs
12 Allen Key M5 1 pc
Do Not Use Power Tools
A
BN
N
N
N
O
O
O
O
A
B
C
C
2x C
B5
12
A
C
5
12
2x
4x A B
O
113
8x
Side View
Bottom View
Back View
BA
N
Back View

12
5
CB
15
Step 3:
To assembler the cross bar I (K), II (L) you will need to use hardware parts 2 with the M4 allen key (11).
To assembler support cross bar leg (M) after cross bar I, II completed.
Step 4:
To fix the cross bar I (K), II (L) to the footboard (B), side rails (C), you will need to use hardware parts (1) and the M4
Allen Key (11).
To attached the L Shape Metal Corner Bracket (15) to the footboard (B) and side rails (C) you will need to use hardware
parts (5) with the M5 Allen Key (12).
Page 5 of 10
1 JCBB M6 x 16mm 8 pcs
5 JCBB M8 x 20mm 8 pcs
11 Allen Key M4 1 pc
12 Allen Key M5 1 pc
15 L-Shape Metal Corner Bracket 2 pcs
Do Not Use Power Tools
Side View
Side View
Top View
Top View
Top View
K L
L
M
M
M
9 132
11
K L
L
M
11
2
13
9
L
L
KL
A B
11L
2x C
11K
2x
2x
B C
C
A
15
2 JCBB M6 x 35mm 6 pcs
9 M6 Hex Nuts 6 pcs
11 Allen Key M4 1 pc
13 M6 Spanner 1 pc
K
11
Back View
A Top End / B Bottom End

14
8 6 12
C G
H
G
14H
G
2x 2x
2x
Step 5:
To install Hydraulic (H) to the Hydraulic Base Support (G), you will need to loose out the M8 HEX nut from the part (G).
After the part (H) go inside the position, put back the M8 HEX Nut and tighten it using M8 Spanner (14).
To install the complete set of (G) to the left and right side rail (C), you will need to use hardware 6 and 8 with Allen key
M5 (12).
To assemble part G, it is a must to make sure the hole go into the right position as shown in (NOTE). And before
tighten the screw, please make sure part G is in same alignment in between left and right side rail.
DO NOT use any power tools as this may damage the bed frame and will invalidate any claims.
Page 6 of 10
* Please insert the screw end to right hand side.
6 JCBB M8 x 40mm 8 pcs
8 M8 Flat Washer 8 pcs
12 Allen Key M5 1 pc
14 M8 Spanner 1 pc
Side View
H
G
C
C
Do Not Use Power Tools
Side View Side View

2x
E
2x F
D
D
I
I
D
2x F
D
9
3
13
4
9
13
11
11
Step 6:
To assemble part D, it is a must to make sure the hole go into the right position as shown in (NOTE). And before tighten
the screw, please make sure part G is in same alignment in between left and right side of part G.
DO NOT use any power tools as this may damage the bed frame and will invalidate any claims.
Page 7 of 10
D
E
E
3 JCBC M6 x 45mm 8 pcs
4 JCBC M6 x 80mm 2 pcs
9 M6 Hex Nuts 10 pcs
11 Allen Key M4 1 pc
13 M6 Spanner 1 pc
Do Not Use Power Tools
Side View
Top View

G
2x
10
14
Step 7:
To assemble part D, it is a must to make sure the hole go into the right position as shown in (NOTE). And before tighten
the screw, please make sure part G is in same alignment in between left and right side of part G.
DO NOT use any power tools as this may damage the bed frame and will invalidate any claims.
Page 8 of 10
* Please insert the screw balance in the middle of the hole.
D
G
12
7
D
Do Not Use Power Tools
7 JCBC M8 x 45mm 6 pcs
10 M8 Hex Nuts 6 pcs
12 Allen Key M5 1 pc
14 M8 Spanner 1 pc
Top View

B
A
J
Step 8:
To put the 4 X BOTTOM PANEL (J), you will need to slightly raise up the beds from the footboard (B) and slot in the
panel go direct to the headboard and continue the second pieces there after the first pieces was in right position.
Page 9 of 10
WARNING:
Take care when assembling the base, assemble the ottoman as closed to its final position. The Ottoman has a
powerful mechanism and after assembly should only be closed and opened when the mattress is in place.
COMPLETE
J
J
J
J

www.happybeds.co.uk
General Care & Maintenance
Please dispose of all packaging safely.
Wipe clean with a slightly damp cloth.
Avoid the use of all household cleaners and abrasives.
Periodically check all screw & fixings to ensure they are secure.
When moving your product, carefully lift into place. Never drag or push the product across the
floor as this will cause damage to the joints. If the product is used on hard flooring, such as
wood or laminated floor, you must place some protection under the legs to stop the product
from moving. If this is not adhered to, it could result in failure to the product that will invalidate
the warranty.
For more information on cleaning and product care visit:
https://www.happybeds.co.uk/help-and-advice
We’ve tried to make this product as easy to assemble as possible. In the unlikely event that
you have problems putting it together or have damaged or missing pieces, please contact
us by visiting:
https://www.happybeds.co.uk/customer-service
Notes