Next MILANO WHITE GLOSS S DESK User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
FITTINGS
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
ASSEMBLY INSTRUCTIONS
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to
be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Keep fittings out of children's reach and keep children well away from the construction area.
• For general cleaning, periodically dust with a soft cloth.
• Do not use furniture polish.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching
or damage.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• A minimum of two persons is required to assemble this product.
CARE INSTRUCTIONS
• Made from MDF,hollow board & Honeycomb board with a pvc foil & a wood effect finish foil.
• Do not rub or scrub the surface when cleaning.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Made in China.
• Do not put hot dishes directly on the surfaces of the item.
•Gloss finishes are prone to light surface scratch and it is therefore very imporant that
you care for this item correctly.
PRODUCT INFORMATION
MILANO WHITE GLOSS S DESK
Page 1 of 10

Please note: Remove the protective film after assembly of this product unless it is stated in
the steps to do so - this will prevent accidental scratches during assembly
1.Insert 8 x cambolts (E) into panels 4, 5 & 6
and tighten with a screwdriver.
2.Insert 2 x bolts (L) into nuts fixed on panel 2
and turn bolts (L) clockwise until tight by hands.
1. Please remove the protective film from the
surface of 5 & 8.
2.Attach panel 5 to panel 8 with 2 x screws (H)
using an Allen key (I) to tighten.
STEP TWO
PARTS
STEP ONE
Page 2 of 10

1. Glue and insert 1 x wooden dowel (A) into panel 5.
2. Please remove the protective film from the
surfaces of 9 & 2.
3. Attach panel 9 to panel 5 .
4. Insert 2 x camlocks (D) into panel 9.
Ensure the arrow indicators are pointing towards
the panel edges before tightening with a
screwdriver.
5.Attach panel 2 to panel 9 with 2 x screws (H)
using an Allen key (I) to tighten.
1. Please remove the protective film from the
surfaces of panels 6 &10.
2. Glue and insert 1 x wooden dowel (A) into
panel 2 .
3. Attach panel 10 to panel 2 .
4. Insert 2 x camlocks (D) into panel 10.
Ensure the arrow indicators are pointing towards
the panel edges before tightening with a
screwdriver.
5.Attach panel 6 to panel 10 with 2 x screws (H)
using an Allen key (I) to tighten.
1. Please remove the protective film from the
surface of panel 7 &11.
2. Glue and insert 1 x wooden dowel (A) into
panel 6 .
3. Attach panel 11 to panel 6 .
4. Insert 2 x camlocks (D) into panel 11.
Ensure the arrow indicators are pointing towards
the panel edges before tightening with a
screwdriver.
5.Attach panel 7 to panel 11 with 2 x screws (H)
using an Allen key (I) to tighten.
STEP FIVE
STEP FOUR
STEP THREE
Page 3 of 10

1. Please remove the protective film from the
surface of panel 1.
Please note: There is a choice of Walnut effect or white
gloss for the back panel 1 . The colour you prefer needs
to face the panels 7,6,2 & 5 when attaching.
2.Attach panel 1 to panels 7, 6 , 2 & 5 with
8 x screws (H) using an Allen key (I) to tighten.
1. Please remove the protective film from the surfaces of
panel 3.
2. Glue and insert 2 x wooden dowels (B) into panel 2.
3. Attach panel 3 to panel 2 .
4.Cover 2 x metal pieces (M) onto 2 x bolts (L)
and then screw 2 x metal nuts (K) with spanner (N)
until tight.
1.Lift the unit upright carefully.
2. Glue and insert 1 x wooden dowel (A) into
panel 8 .
3. Attach panel 4 to panels 1 & 8 with 2 x screws (H)
using an Allen key (I) to tighten.
4. Insert 2 x camlocks (D) into panel 8 .
Ensure the arrow indicators are pointing towards
the panel edges before tightening with a
screwdriver.
STEP SIX
STEP SEVEN
STEP EIGHT
Page 4 of 10

1.Use 8 x stickers (F) to cover the holes on
panels 7, 9 , 10 & 11.
2.Use 2 x stickers (G) to cover the holes on panel 3.
1.Please check the height of metal bracket (O) - from
the ground 1596 mm- to determine the height of hole on
the wall
2. Drill one hole and insert wall plugs ,then put
the screw through the 1× metal bracket (O)
into the wall
Warning:
Always ensure intended wall area to be drilled is
free from hidden electrical wires, water and gas
pipes.
Warning:
Wall fixings are not included- please source
suitable fixings for your wall type. If in doubt,
please consult a qualified trades person.
1.Move assembly unit close to the bracket (O)
STEP NINE
STEP TEN
STEP ELEVEN
Page 5 of 10

1.Ensure the brackets (O) to fit in the groove
under the top panel 4 .
2.Move the unit on the appropriate position, and then
fix the bracket (O) with 1 × screw (J) with
a screwdriver to tighten
3.This product must be fitted to the wall to prevent
damage to the product during use. Periodically check
that no fittings have loosened.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP TWELVE
Page 6 of 10

Page 7 of 10

Page 8 of 10

Page 9 of 10

Page 10 of 10