Happy Beds Houston Wooden Dressing Table and Mirror User manual

Title of Product
Assembly Instructions
www.happybeds.co.uk
Important before assembly:
.
Health & Safety:
.
Read these instructions carefully before assembling or using the product.
Please check the contents of the boxes before attempting to assemble this product. The instructions will
have a checklist of parts and fittings.
It would be sensible to lay a rug or a carpet on the floor where you intend to assemble the product, to avoid
scratches and damaging the product or the floor.
Assemble the product as close to its intended final location/room as possible.
Do NOT use any power tools as this may damage the frame.
This product or some parts of this product will be heavy. Please use an assistant when lifting.
Please keep small parts out of reach of children.
Always use on a level, even surface.
DO NOT jump on the product or any of its parts.
DO NOT use this product if any parts are missing, damaged or worn.
DO NOT use this product unless all fixings are secured.
Please keep these instructions for future reference.
Houston Wooden Dressing Table and Mirror

@
This product or some parts of this product will be heavy. Please use an assistant
when lifting.
Never drag or push the pieces across a hard or stone floor as this will cause
damage to the joints. Use a carpet or a rug for extra care.
If you have problems assembling or have damaged or missing pieces, please
contact us by visiting:
https://www.happybeds.co.uk/customer-service
(Not metal)
These tools are not
necessary, but may
help to assemble
certain parts of the
product.
Do NOT use any power
tools as this may
damage the frame.

HOUSTON DRESSING TABLE & MIRROR
IMPORTANT : READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE OR
USE YOUR HOUSTON DRESSING TABLE & MIRROR .
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ASSEMBLY:
Assembly should be carried out with this item laying flat, not standing upright.
Assemble on a soft, clean surface to prevent damages.
To erase the numbers printed on the pieces, use the rubber inside the accessories pack.
HEALTH & SAFETY:
DO NOT use this product if any parts are missing, damaged or worn.
DO NOT use this product unless all fixings are secured.
Always use on a level, even surface.
CARE & MAINTENANCE:
Periodically check all screws & fixings to ensure they are secure.
DO NOT push this product as this will cause damage.
Always lift this product with two people to repositions.
Keep any sharp objects away from this product.
ASSEMBLY INSTRUCTIONS
Page of 8
Vendor: S000350
1

2
Page of 8
Vendor: S000350
Parts List Hardware List
Part Descripion Qty Part Description Qty
** You will need a small mallet and a screwdriver for assembly.
** Some screws and wooden dowel may remain.
** Note : To secure the item to the wall, hardware E ( 2 pcs )
and K ( 2 pcs ) are not provided.
01 1
Top panel
02
03
04
05
06
07
08
09
10
Bottom panel
Metal middle support
1
1
1
1
2
2
Side panel ( Left )
Side panel ( Right )
Back panel
Metal Side ( Down )
A2
Cam lock
Minifix screw
B
Plastic cap
M8 x 30mm Wood Dowel
C
D
E
F
G
H
I1
J
M6 x 50mm CSK Cap Wood screw
M3.5 x 16mm C.B Screw
8
8
8
8
4
14
8
Allen key M4 1
JCBC screw M6 x 30mm 12
JCBC screw M6 x 40mm 12
M4 x 38mm C.B Screw
A1
A3
11
Drawer front
Drawer side
Drawer back
Drawer bottom
1
2
1
1
14'' Drawer slide (Left / Right)
14'' Drawer slide (Left / Right)
2
2
K
12
13
14
15
Metal bottom support 1
Metal mirror support 2
Hanger plate ( mirror ) 1
Drawer bone 1
06
09
07
07 08
10
Wall plug -
8'' x 1'' PP tape 2
16 2
Metal Side ( Up )
I2
01
02
04
03 05
12
16
14
13
15
11
12
13
15
16

3
Page of 8
Vendor: S000350
Step 1: Prepare these parts for assembly using hardware parts A1, A2, B, D and I1.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
A1
A1
A3
A2
I1
I1
I1
DDD
01
A2
03
04
A1
A1
B
Step 2: Attach side panel (3) and (4) to top panel (1) using hardware A1 and A2 with a screwdriver
(not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 3: Insert back panel (5) along the slot.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
03
04 01
01
05
03
04
x4 x2
x4
A1
B
x2
x4
A3 x 4
x2 x2 x2

4
Page of 8
Vendor: S000350
Step 4: Attach bottom panel (2) to side panel (3) and (4) using hardware C and F.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 5: Attach metal middle support (13) to bottom panel (2) using hardware F and G.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
02
C
F
F
G
13
Step 6: Attach metal mirror support (15) to hanger plate mirror (11) using hardware F and G.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
02
01
03
04
02
01
03
04
F
G
15
11
15
15
13
13
C x 4
F
F
G x 6
F
G x 4

5
Page of 8
Vendor: S000350
16
F
H
Step 7: Attach metal side (12) to metal side (16) using hardware F, G and H.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 8: Attach metal side (12) and (16) to metal middle support (13), metal bottom support (14) and
metal mirror support (15) using hardware F and H.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
16
11
02
14
13
15
F
H x 5
12
H
F
F
G x 2
H x 2
12 16
G
12
16
12
16

6
Page of 8
Vendor: S000350
Step 9: Attach metal side (12) and (16) to metal middle support (13), metal bottom support (14) and
metal mirror support (15) using hardware F and H.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 10: Insert hardware A1 onto drawer bone (9) with a screwdriver (not provided).
Insert hardware A2 onto drawer front (6) and drawer back (8) with a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
16
H
F
16
11
02
13
15
14
A2 A2
A2 A2
06
08
F
H x 5
A2 x 4
A1
09
x4
A1 x 4
12

7
Page of 8
Vendor: S000350
I2
I2
I2
D
D
D
D
D
D
I2
I2
I2
Step 11: Attach drawer bone (9) to drawer front (6) and drawer back (8) using hardware A1 and A2 with a
screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
06
09
08
A1
A3
A1 A2
07
08
06
09
10
E
E
10
09
09
09
06 06
06
07
07
07
07
10
08
08
08
A3 x 4
D x 6
E x 8
( L/R )
I2 x 2
x4
x4
Step 12: Attach the 1x Drawer Side (7) to the Drawer Front (6) and Drawer Back (8) using hardware E.
Then insert the Drawer Bottom (10) and attach the other 1x Drawer Side (7) to the Drawer Front (6) and
Drawer Back (8) using hardware E. Attach the hardware I2 to the Drawer Sides (7) using hardware D.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.

Page of 8
Vendor: S000350
8
Step 14: To secure the item to the wall use hardware E, J and K using a screwdriver (not provided).
Then attach hardware part J to top panel (1) using hardware D with a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Additional Information:
· For complete product information, images and dimension diagrams please visit the website
www.birlea.com
· If you have any issues with your item please contact the retailer directly you purchased it from
who will be able to resolve any issues with Birlea.
· Why don't you send us photos of your assembled furniture to [email protected] to be shared in
our #birleahome feature on instagram.
E
J
K
1.
J
D
2.
Step 13: Assemble the drawers in place along the drawer slides.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
I2
I1 I1
I2
06
01
PLEASE NOTE that wall fixings are not supplied as different wall materials require different fixing
devices. You must use fixings devices suitable for the type of wall you intend to mount product to.
Ensure the head of any screw used has a diameter greater than the mounting hole and the fixing
is safe and secure before use.
Birlea Furniture advise you use the wall straps provided to further enhance the safety of this
product.
D x 2
E x 2
J x 2
K x 2
11

www.happybeds.co.uk
General Care & Maintenance
Please dispose of all packaging safely.
Wipe clean with a slightly damp cloth.
Avoid the use of all household cleaners and abrasives.
Periodically check all screw & fixings to ensure they are secure.
When moving your product, carefully lift into place. Never drag or push the product across the
floor as this will cause damage to the joints. If the product is used on hard flooring, such as
wood or laminated floor, you must place some protection under the legs to stop the product
from moving. If this is not adhered to, it could result in failure to the product that will invalidate
the warranty.
For more information on cleaning and product care visit:
https://www.happybeds.co.uk/help-and-advice
We’ve tried to make this product as easy to assemble as possible. In the unlikely event that
you have problems putting it together or have damaged or missing pieces, please contact
us by visiting:
https://www.happybeds.co.uk/customer-service
Notes