Harbor Freight Tools One Stop Gardens 92346 User manual

COPPER SOLARCOPPER SOLAR
COPPER SOLARCOPPER SOLAR
COPPER SOLAR
GARDEN LIGHTGARDEN LIGHT
GARDEN LIGHTGARDEN LIGHT
GARDEN LIGHT
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit ourWeb site at http://www.harborfreight.com
Copyright © 2005 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor FreightTools.
For technical questions and replacement parts, please call 1-800-444-3353
92346

SKU 92346 For technical questions, please call 1-800-444-3353 Page2
Specifications
SaveThis Manual
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. Keep
your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING:When using this product, basic safety precautions should always
be followed to reduce the risk of personal injury and damage to equipment.
WARNING: The brass components of this product contain lead, a chemical
known to the State of California to cause birth defects (or other reproductive
harm). (California Health & Safety code § 25249.5, et seq. )
Read all instructions before using this product!
1. Keep work area clean. Clutteredareasinviteinjuries.
2. Keep children away. Children must never be allowed in the work area. Do
not let them handle machines, tools, or extension cords.
3. Use the right product for the job.There are certain applications for which
this product was designed.Do not use this accent light for lighting a walkway.
It does not have enough illumination power.Do not modify this product and
do not use it for a purpose for which it was not intended.
4. Check for damaged parts. Before using any product, any part that appears
damaged should be carefully checked to determine that it will operate
properly and perform its intended function.Any part that is damaged should
be properly repaired or replaced by a qualified technician.
5. Replacement parts and accessories. When servicing, use only identical
replacement parts.Use of any other parts will void the warranty.Only use
accessories intended for use with this product.Approved accessories are
available from Harbor Freight Tools.
6. Maintenance. For your safety, service and maintenance should be performed
regularlybyaqualified technician.
Note:Performanceof this productmayvarydependingon variationsin batterypower.
Item Description
Light Material Solid brass housing with antique copper finish;
Glass lens cover
Metal Stake Steel tube with threads; 14 (L) inches
Overall Dimensions 5 (dia.) x 18 (H) inches (assembled)
Battery 2 - AA, 1.2 V, rechargeable Ni Cad, 600 mAh
Charging Power Source Photo cell (auto-on), on top of unit
Switch Toggle, under top
Light Source LED, bright white
Weight 1.6 lbs.
Run Time Up to 12 hours on with a full battery charge

SKU 92346 For technical questions, please call 1-800-444-3353 Page3
Unpacking
When unpacking, check to make sure that all the parts are included.If any parts
are missing or broken, please call Harbor FreightTools at the number on the cover
of this manual.
Operation
1. To enable operation, carefully slide the Switch to the On position.
2. Test the Light by first setting it in the sun for one hour to (minimally) charge
the Batteries, then place in a darkened room.If light is generated, it is
working.If it does not light, refer to the OperatingTips, below.
3. To assemble, carefully screw in the StakeTube (3) into the bottom of the Light
Housing (1).Then screw in the Stake (2) into the bottom of the StakeTube (3)
4. Pick the location for the Solar Garden Light where the sun will hit it for at least
eight hours during the day.Verify On/Off Switch is in the On position.
If placed in the yard, carefully insert the assembled unit into the grass or soft
ground.First check, and avoid, underground wires;Do not hammer into the
ground.
5. The light will automatically turn on after the sun sets. Make sure no other light
source hits it at night (i.e., porch light).
OperatingTips
1. If the light does not turn on, the Switch may be in the Off position.
2. Initially, it may take three sunny days to fully charge the Batteries.
3. Normally, eight hours of daily, direct sunlight on the top solar cells is required
to operate.
4. A dim light may be due to a weak or dead battery, or lack of sunlight.Replace
batteries when this happens.Normally, the batteries should last one year.
Stake (2)
Light Housing (1)
Stake Tube (3)
On/Off
Switch
Cap Nuts
Solar Panel

SKU 92346 For technical questions, please call 1-800-444-3353 Page4
5. A dirty surface on the solar panel will not let in enough sunlight to allow the
batteries to charge.This will shorten battery life, and cause the light to
malfunction.Periodically clean the solar panel with a clean cloth and water.
6. Before storing the unit, slide the On/Off Switch to the Off position.
Replacing the Batteries
1. Push the On/Off Switch to the Off position.
2. Remove the two Cap Nuts on top of the Light Housing (1) and carefully pull
off theTop.See photo below and on the previous page.
3. Unscrew the two Phillip Head Screws holding the Battery Cover in place.
4. Remove the Battery Cover and the existing Batteries.Replace with new
batteries of the same type (see Specification Table), being careful of the
polarity (+ and –).
5. Replace the Battery Cover and Screws.
6. Carefully insert the LED Light into the hole of the Light Housing (1) and align
the Mounting Screws into the holes in theTop.
7. Screw in the Cap Nuts.
Caution: Moisture entering the housing could damage parts. Be sure the Cap
Nuts are tight.
Parts List
Part No. Description
1. Light Housing
2. Stake, Metal
3. Tube, Stake, Metal
LED Light
Phillip Head Screw
Phillip Head Screw
Battery Cover
Light Housing (1) Hole
Batteries
Mounting Screw
Mounting Screw