Harbor Freight Tools Chicago Electric 47953 User manual
CORDLESS SCREWDRIVER KIT – 3.6 VOLT
Model 47953
OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
Copyright 2002 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
®
SPECIFICATIONS TABLE
SAVE THIS MANUAL
You will need this manual for the safety warnings and precautions, operating,
inspection, maintenance and cleaning procedures, parts list and assembly
diagram. Keep your invoice with this manual. Write the invoice number on the
inside of the front cover. Keep this manual and invoice in a safe and dry place for
future reference.
GENERAL SAFETY WARNINGS AND PRECAUTIONS
1. KEEP WORK AREA CLEAN AND DRY. Cluttered, damp, or wet work areas
invite injuries.
2. KEEP CHILDREN AWAY FROM WORK AREA. Do not allow children to handle
this product.
3. STORE IDLE EQUIPMENT. When not in use, tools and equipment should be
stored in a dry location to inhibit rust. Always lock up tools and equipment, and
keep out of reach of children.
4. DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR
DRUGS. Read warning labels on prescriptions to determine if your judgement or
reflexes are impaired while taking drugs. If there is any doubt, do not attempt to
use this product.
SKU 47953 PAGE 2
5. USE EYE PROTECTION. Wear ANSI approved safety impact eye goggles when
using this product. ANSI approved safety impact eye goggles are available from
Harbor Freight Tools.
6. DRESS SAFELY. Do not wear loose clothing or jewelry, as they can become
caught in moving parts. Wear a protective hair covering to prevent long hair from
becoming caught in moving parts. If wearing a long-sleeve shirt, roll sleeves up
above elbows.
7. DO NOT OVERREACH. Keep proper footing and balance at all times to prevent
tripping, falling, back injury, etcetera.
8. INDUSTRIAL APPLICATIONS MUST FOLLOW OSHA REQUIREMENT.
9. STAY ALERT. Watch what you are doing at all times. Use common sense. Do
not use this product when you are tired or distracted from the job at hand.
10. CHECK FOR DAMAGED PARTS. Before using this product, carefully check that
it will operate properly and perform its intended function. Check for damaged
parts and any other conditions that may affect the operation of this product.
Replace or repair damaged or worn parts immediately.
11. REPLACEMENT PARTS AND ACCESSORIES: When servicing, use only
identical replacement parts. Only use accessories intended for use with this
product. Approved accessories are available from Harbor Freight Tools.
12. MAINTAIN THIS PRODUCT WITH CARE. Keep this product clean, dry, and
keep all cutting bits sharp for better and safer performance.
13. MAINTENANCE: For your safety, service and maintenance should be performed
regularly by a qualified technician.
14. USE THE RIGHT TOOL FOR THE JOB. Do not attempt to force a small tool or
attachment to do the work of a larger industrial tool. There are certain
applications for which this tool was designed. It will do the job better and more
safely at the rate for which it was intended. Do not modify this tool, and do not
use this tool for a purpose for which it was not intended.
15. WARNING: The warnings, precautions, and instructions discussed in this manual
cannot cover all possible conditions and situations that may occur. The operator
must understand that common sense and caution are factors, which cannot be
built into this product, but must be supplied by the operator.
SKU 47953 PAGE 3
SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS
1. MAINTAIN A SAFE WORKING ENVIRONMENT. Keep the work area well lit.
Make sure there is adequate surrounding workspace. Always keep the work
area free of obstructions, grease, oil, trash, and other debris. Do not use the
Cordless Screwdriver in a damp or wet location. Do not use near flammable
gasses or liquids.
2. GROUND THIS PRODUCT. The electrical Charger for this product is equipped
with a 2-prong Plug. Never modify the Charger in any way. To comply with the
National Electric Code, and to provide additional protection from the risk of
electrical shock, this product should only be connected to a 3-prong Adapter Plug
(not provided), and a 120 Volt, 3-hole electrical outlet that is protected by a
Ground Fault Circuit Interrupter (GFCI). (See Figure A.)
CHARGER
3-PRONG
ADAPTER PLUG
120 VOLT
OUTLET
FIGURE A
3. IF AN EXTENSION CORD (not provided) IS USED, MAKE SURE TO USE
ONLY UL APPROVED CORDS HAVING THE CORRECT GAUGE AND
LENGTH. (See Figure B, next page.)
4. PROTECT THE CHARGER CORD. Do not carry the Cordless Screwdriver by its
Charger Cord, or pull the Charger Cord to remove the Charger from an electrical
outlet. Protect the Charger Cord from sharp objects, heat, and oil.
5. HOLD THE CORDLESS SCREWDRIVER FIRMLY SO THAT IT WILL NOT BE
PULLED FROM YOUR HANDS WHILE IN USE.
6. SECURE THE WORKPIECE. Whenever possible, secure the workpiece with a
vise or clamps.
SKU 47953 PAGE 4
7. PROPER BATTERY CARE: Battery leakage may occur under extreme usage or
temperature conditions. If battery fluid comes in contact with skin, wash with
soap and water and rinse with lemon juice and vinegar. If the fluid comes into
contact with the eyes, flush with water for several minutes and contact a doctor
immediately. Never burn batteries, as they can explode in a fire. Do not charge
a Cordless Screwdriver with a leaking battery. Contact local solid waste
authorities for instructions on correct disposal or recycling of the batteries.
8. WARNING: People with pacemakers should consult their physician(s) before
using this product. Operation of electrical equipment in close proximity to a heart
pacemaker could cause interference or failure of the pacemaker.
UNPACKING
When unpacking, check to make sure all the parts shown on the Parts List on page 8 are
included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as possible.
OPERATING INSTRUCTIONS
NOTE: For additional references to the parts listed below, refer to the Assembly
Diagram on page 9.
To Adjust The Handle:
1. The Handle Assembly (parts #6, #7, #8, #9) of the Cordless Screwdriver may be
angled for ease of control, or easier access to the workpiece. The Handle
Assembly is fixed in position by a Locking Switch (part #12) To adjust the Handle
Assembly, push and hold the Locking Switch forward while at the same time
moving the Handle to the desired position. Then, release the Locking Switch.
The Handle will now be locked in the desired position. (See Figure C.)
FIGURE B
SKU 47953 PAGE 5
EXTENSION CORD AWG RATING CHART - 120 VOLT
Table of contents
Other Harbor Freight Tools Power Screwdriver manuals
