Harbor Freight Tools Central Machinery 46725 User manual

HEAVY DUTY WORK STATION
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit ourWeb site at http://www.harborfreight.com
Copyright © 2001 by Harbor Freight Tools®. All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
46725
Due to continuing improvements, actual product may differ slightly from the product described herein.

Page 2SKU 46725
Specifications
ITEM DESCRIPTION
Tabletop Dimensions 20-1/8 (W) x 17-3/4 (D) x 3/4 (T) inches
Tabletop Material 3/4 inch pressboard
Frame Material Formed and stamped sheet steel
Table Height 23-3/4 inches (minimum)
30-1/4 inches (maximum)
Top Shelf Dimensions 15-5/16 (W) x 13-1/8 (D) x 1/8 (T) inches
Bottom Shelf Dimensions 19-1/2 (W) x 17-3/16 (D) x 1/8 (T) inches
Weight 15.55 lbs
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instructions,
operating and maintenance procedures, parts list and diagram. Keep your invoice with this
manual. Write the invoice number on the inside of the front cover. Keep the manual and
invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or power tools in damp or wet
locations. Don’t expose to rain. Keep work area well lighted. Do not use electrically
powered tools in the presence of flammable gases or liquids.
3. Keep children away. Children must never be allowed in the work area. Do not let
them handle machines, tools, or extension cords.
4. Store idle equipment. When not in use, tools must be stored in a dry location to
inhibit rust. Always lock up tools and keep out of reach of children.
5. Do not force tool. It will do the job better and more safely at the rate for which it was
intended. Do not use inappropriate attachments in an attempt to exceed the tool
capacity.
6. Use the right tool for the job. Do not attempt to force a small tool or attachment to
do the work of a larger industrial tool.There are certain applications for which this tool
was designed.Do not modify this tool and do not use this tool for a purpose for which
it was not intended.
7. Dress properly. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically non-conductive clothes and non-skid footwear
are recommended when working. Wear restrictive hair covering to contain long hair.

Page 3SKU 46725
8. Use eye and ear protection. Always wear ANSI approved impact safety goggles.
Wear a full face shield if you are producing metal filings or wood chips.Wear an ANSI
approved dust mask or respirator when working around metal, wood, and chemical
dusts and mists.
9. Do not overreach. Keep proper footing and balance at all times. Do not reach over or
across running machines.
10. Maintain tools with care. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories. Inspect
tool cords periodically and, if damaged, have them repaired by an authorized
technician.The handles must be kept clean, dry, and free from oil and grease at all
times.
11. Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.
12. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment and binding of moving parts; any broken parts
or mounting fixtures; and any other condition that may affect proper operation. Any
part that is damaged should be properly repaired or replaced by a qualified
technician.Do not use the tool if any switch does not turn On and Off properly.
13. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor
Freight Tools.
14. Do not operate tool if under the influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your judgment or reflexes are impaired while
taking drugs. If there is any doubt, do not operate the tool.
15. Maintenance. For your safety, service and maintenance should be performed
regularly by a qualified technician.
16. Secure tool to table. Tool must be securely clamped or mounted to table top for safe
operation.
Warning:The warnings,cautions,and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be under-
stood by the operator that common sense and caution are factors which cannot be
built into this product,but must be supplied by the operator.

Page 4SKU 46725
Unpacking
When unpacking, check to make sure that all the parts are included.Refer to the Parts List
and Assembly Drawing at the end of this manual.If any parts are missing or broken, please
call Harbor Freight Tools at the number on the cover of this manual as soon as possible.
Assembly
Refer to the Assembly Drawing on page 7 during this procedure.
1. Assemble Two Legs (8) to one Lower Short Frame (7) and two Lower Long Frames (6)
by threading Screws (12), with aWasher (15).
Refer to illustrations “E”and “F”on the Assembly Drawing. Note that a Washer is
placed under every Screw. Tighten securely using a large Phillips screwdriver.
2. Place the PVC Feet (11) on the bottom of each Leg.
3. Assemble the Short Middle Frame (5) and two Long Middle Frames (4) to the Legs (8),
just assembled. Depending on the desired table height, also mount the Height
Adjuster (9) on the outside of the Legs.Use Screws (13), andWashers (15).Tighten
securely.
Refer to illustrations “A”, “B”, “C” and “G” on the Assembly Drawing.
Height Adjuster (9) Short Middle Frame (5)
Long Middle Frame (4)
Screws (12)
Washers (15) Leg (8)
PVC Feet (11)
REV 07/03

Page 5SKU 46725
4. Assembly the other two Legs with the Short Middle Frame (5) and the Short Lower
Frame(7).
Use Screws (12) through the Height Adjuster, Screws (13) through Short Lower Frame
(7), andWashers (15).Tighten securely.
5. Slide the Middle Wood Plate (2) into the Long Middle Frames (4)
6. Slide the Lower Wood Plate (3) into the Long Lower Frames (6).
7. Attach the Leg subassembly (done in step 4) to the extending Long Middle Frames (4)
and the Long Lower Frames (6).
Use Screws (12) through the Height Adjuster, Screws (13) through Short Lower
Frame (7), andWashers (15).Tighten securely.
8. Place the Wood Table Top (1) upside down on the floor, exposing the mounting holes.
9. Mount the Connector Brackets (10) using Screws (16).Tighten securely.
10. Place the completed frame assembly (Height Adjuster brackets facing down) over the
Connector Brackets and secure with Screws (13), andWashers (15).Tighten securely.
Refer to illustration “D” on the Assembly Drawing.
11. Turn the completedWork Station over so that it stands on its feet.
12. Stick the Magnetic Strips (17 and 18) to the Long Middle Frame (4) and the Short
Middle Frame (5).These magnetic strips can be used to hold light metal objects such
as tools.
Caution: MaximumWeight Capacity = 1,000 Lbs. dead load. Do not exceed this maxi-
mum weight capacity.
Caution:Only use normal sized table top equipment on thisWork Station. Oversized or
overweight equipment can damage, and possibly collapse theWork Station.
Maintenance
1. Periodically check and tighten all Screws and Nuts on the Work Station assembly.
2. Store the Work Station in a clean and dry location.
3. When moving, do not drag the Work Station.Left and carry.
REV 07/03

Page 6SKU 46725
Parts List
Item # Description Qty
1 Wood Table Top 1
2 Wood Plate, Middle 1
3 Wood Plate, Lower 1
4 Frame, Long Middle 2
5Frame,ShortMiddle 2
6 Frame, Long Lower 2
7 Frame, Short Lower 2
8Leg 4
9 HeightAdjuster 4
10 Connector Bracket 4
11 PVC Feet 4
12 Screw, 5x12 mm 16
13 Screw, 5x10 mm 36
15 Washer, 5 mm 52
16 Screw, 8x5/8" 4
17 Magnetic Strip, 11-3/4" (300 mm) 1
18 Magnetic Strip, 9-3/4" (250 mm) 1
NOTE:Some parts are listed and shown for illustra-
tionpurposesonly and arenotavailableindividually
as replacement parts.
PLEASE READTHE FOLLOWING CAREFULLY
THEMANUFACTURERAND/ORDISTRIBUTORHASPROVIDEDTHEPARTSDIAGRAMINTHIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-
TOR MAKES ANY REPRESENTATIONORWARRANTY OF ANY KINDTOTHEBUYERTHAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/ORDISTRIBUTOREXPRESSLYSTATESTHAT ALLREPAIRSANDPARTSREPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSEDTECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTSTHERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTSTHERETO.
REV 07/03

Page 7SKU 46725
Assembly Drawing