Harman Kardon AVR 230 User manual

Harman Kardon Service Manual
AVR 165/230
5.1 CHANNEL A/V RECEIVER
Released EU2011 Harman Consumer Group, Inc. Rev 0, 10/2011
8500 Balboa Boulevard
Northridge, California 91329
CONTENTS
EXPLODED VIEW AND PARTS 15
PARTS LIST 16
IC PINOUTS 40
PCB DRAWINGS 87
BLOCK DIAGRAMS 97
WIRING DIAGRAM 99
AMP BIAS ADJUSTMENT 100
SCHEMATIC DIAGRAMS 101-111
ESD WARNING 2
FRONT AND REAR PANELS 3
REMOTE CONTROL 7
RESET REMOTE AND PROCESSOR 9
TROUBLESHOOTING GUIDE 10
BASIC SPECIFICATIONS 11
PACKAGE LISTS AND PARTS 13
DISASSEMBLY 14

Each precaution in this manual should be followed during servicing.
Components identified with the IEC symbol in the parts list are special significance to safety. When replacing a component identified with
, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the
parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably
insulated from the supply circuit before retuming the product to the customer.
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and
semiconductor "chip" components.
The following techniques should be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on
your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to
prevent electrostatic charge build-up or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges
sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement
ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the
chassis or circuit assembly into which the device will be installed.
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together
or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.
CAUTION :
Harman Kardon
AVR 165/230V Service Manual
Page 2 of 111

4
AVR 1650/AVR 165 Front-Panel Controls
Front-Panel Controls
Power
Indicator
Message
Display
Volume
Knob
Surround Mode
Select Buttons
Set
Button
IR
Sensor
Power
Button
Left/Right
Buttons
Headphone Jack/
EzSet/EQ Mic
Connector
Source Select
Buttons
Tuning Mode
Button
Digital Input
Button
Surround-Mode
Category Button
Up/Down Buttons/
Tuning Buttons
USB
Port
Aux Analog
Audio Input
Connector
Channel
Level Control
Button
Harman Kardon
AVR 165/230V Service Manual
Page 3 of 111

5
AVR 1650/AVR 165
ENGLISH
Front-Panel Controls, continued
Front-Panel Controls, continued
Power indicator: This LED has three possible modes:
LED is off: Indicates that the AVR is unplugged or the rear-panel Main Power switch•
is off.
LED glows amber: Indicates that the AVR is in the Standby mode.•
LED glows white: Indicates that the AVR is turned on.•
IMPORTANT NOTE: If the PROTECT message ever appears on the AVR’s front-panel
Message display, turn off the AVR and unplug it from the AC outlet. Check all speaker
wires for a possible short circuit (the “+” and “–” conductors touching each other
or both touching the same piece of metal). If a short circuit is not found, bring the
unit to an authorized Harman Kardon service center for inspection and repair before
using it again.
IR sensor: This sensor receives infrared (IR) commands from the remote control. It is
important to ensure that the sensor is not blocked.
Set button: Press this button to select the currently highlighted menu item.
Message display: Various messages appear in this two-line display in response to
commands and changes in the incoming signal. In normal operation, the current source
name appears on the upper line, while the surround mode is displayed on the lower line.
When the on-screen display menu system (OSD) is in use, the current menu settings
appear.
Surround-Mode Select buttons: After you have selected the desired surround-mode
category, press these buttons to select a specific mode within the category, such as to
change from Dolby®Pro Logic®II Movie mode to Logic 7®Movie mode. Surround-mode
availability depends on the nature of the source input signal, i.e., digital versus analog,
and the number of channels encoded within the signal.
Volume knob: Turn this knob to raise or lower the volume.
Power button: Press this button to turn the AVR on or to place it in the Standby mode.
Tuning Mode button: This button toggles between manual (one frequency step at a
time) and automatic (seeks frequencies with acceptable signal strength) tuning mode. It
also toggles between stereo and mono modes when an FM station is tuned in.
Channel Level Control button: Press this button to activate the channel-level adjustment
feature. After pressing this button, use the Up/Down buttons to select the channel for
adjustment and use the Left/Right buttons to adjust the channel’s level.
Digital Input button: Press this button to change the audio input for the current source.
Use the Left/Right buttons to cycle through the available inputs. Although you can
assign any digital audio input to any source, the analog audio inputs are all permanently
dedicated to the source with which they are labeled.
Left/Right buttons: Use these buttons to navigate the AVR’s menus.
Up/Down buttons/Tuning buttons: Use these buttons to navigate the AVR’s menus.
When the radio is the active source, use these buttons to tune stations according to the
setting of the Tuning Mode button (see above).
Surround-Mode Category button: Press this button to select a surround-sound
category. Each press changes the surround-mode category: Auto Select, Virtual, Stereo,
Movie, Music and Video Game. To change the specific surround-sound mode within the
category, use the Surround Mode Select buttons. See
Audio Processing and Surround
Sound, on page 20, for more information on surround modes.
Headphone jack/EzSet/EQ Mic connector: Connect a 1/4" stereo headphone plug to
this jack for private listening. This jack is also used to connect the supplied microphone
for the EzSet/EQ procedure described in
Configure the AVR for Your Speakers, on
page 17.
Source Select buttons: Press these buttons to select the active source.
USB port: You can use this port to perform software upgrades that may be offered in
the future. Do not connect a storage device, a peripheral product or a PC here, unless
instructed to do so as part of an upgrade procedure.
Aux Analog Audio Input connector: Connect an auxiliary source component that will
be used only temporarily, such as a camcorder, portable music player or game console,
here.
Harman Kardon
AVR 165/230V Service Manual
Page 4 of 111

6
AVR 1650/AVR 165 Rear-Panel Connectors
Rear-Panel Connectors
AVR 1650/AVR 165 Rear-Panel Connections (AVR 1650 shown)
HDMI Input
Connectors
HDMI®
Monitor Out
Connector
Composite Video
Monitor Out
Connector
DVD
Component Video
Input Connector
Radio Antenna
Connectors
Subwoofer
Connector
Analog Audio
Input/Output
Connectors
Speaker
Connectors
12V Trigger
Connector
Main Power
Switch
AC Input
Connector
Optical Digital
Output Connector
Digital Audio
Input Connectors
The Bridge IIIP
Connector
IR Remote
In/Out Connectors
Composite
Video Input
Connectors
Video 2 Out
Connector
Harman Kardon
AVR 165/230V Service Manual
Page 5 of 111

7
AVR 1650/AVR 165
ENGLISH
Rear-Panel Connectors, continued
Rear-Panel Connectors, continued
Radio Antenna connectors: Connect the included AM and FM antennas to their
respective terminals for radio reception.
HDMI Monitor Out connector: If your TV has an HDMI connector and you have HDMI or
component video source devices, use an HDMI cable (not included) to connect it to the
AVR’s HDMI Monitor Out connector.
Notes on using the HDMI Monitor Out connector:
When connecting a DVI-equipped display to the HDMI Monitor Out connector, use•
an HDMI-to-DVI adapter and make a separate audio connection.
Make sure the HDMI-equipped display is HDCP-compliant. If it isn’t, do not•
connect it via HDMI; use an analog video connection instead and make a separate
audio connection.
HDMI Input connectors: The HDMI (High-Definition Multimedia Interface®) feature is
a connection for transmitting digital audio and video signals between devices. If your
source devices have HDMI connectors, using them will provide the best possible video
and audio performance quality. Since the HDMI cable carries both digital video and
digital audio signals, you do not have to make any additional audio connections for
devices you connect via HDMI connections. See Connect Your Source Devices , on page
13, for more information.
Composite Video Monitor Out connector: If your TV or video display does not have
an HDMI connector, or if your TV does have an HDMI connector
but you are connecting
some source devices with only composite video connectors , use a composite video
cable (not included) to connect the AVR’s Composite Video Monitor Out connector to your
TV’s composite video input connector.
DVD Component Video Input connector: If your Blu-ray Disc™or DVD player does
not have an HDMI connector but does have a component video connector, using the
component video connector will provide superior video performance. You will also need
to make an audio connection from the player to the AVR.
Digital Audio Input connectors: If your non-HDMI source devices have digital outputs,
connect them to the AVR’s digital audio connectors. NOTE: Make only one type of digital
connection (HDMI, optical or coaxial) from each device. See
Connect Your Source
Devices , on page 13, for more information.
Video 2 Out connector: Connect an analog video recorder’s video input connector to the
AVR’s Video 2 Out connector. You can record any composite video input signal. NOTE: To
record the audio and video from the source device, connect the AVR’s Video 2 Out Analog
Output connectors to the analog video recorder’s audio inputs.
Composite Video Input connectors: Use composite video connectors for video source
devices that don’t have HDMI or component video connectors. You will also need to
make an audio connection from the source device to the AVR. See
Connect Your Source
Devices, on page 13, for more information.
IR Remote In/Out connectors: When the IR Sensor on the front panel is blocked (such
as when the AVR is installed inside a cabinet), connect an optional IR receiver to the IR
Remote In connector. The IR Remote Out connector may be connected to the IR input
of a compatible product to enable remote control through the AVR. See
Connect IR
Equipment, on page 15, for more information.
The Bridge IIIP connector: Connect an optional Harman Kardon The Bridge IIIP docking
station to this connector. Insert the plug until it snaps into place in the connector.
IMPORTANT: Connect The Bridge IIIP only with the AVR’s power turned off. See
Connect
The Bridge IIIP, on page 15, for more information.
Subwoofer connector: Connect this jack to a powered subwoofer with a line-level
input. See
Connect Your Subwoofer, on page 13, for more information.
Analog Audio Input/Output connectors: Use the AVR’s Analog Audio Input/Output
connectors for source devices that don’t have HDMI or digital audio connectors. Use the
Video 2 Out and Tape Out connectors to connect to the audio inputs of a VCR and tape
deck. See
Connect Your Source Devices, on page 13, for more information.
Speaker connectors: Use two-conductor speaker wire to connect each set of terminals
to the correct speaker. See
Connect Your Speakers, on page 13, for more information.
Optical Digital Output connector: Connect a digital audio recorder’s optical digital
input to the AVR’s Optical Digital Output connector. You can record both coaxial and
optical digital PCM audio signals. (Dolby Digital and DTS®bitstreams are not available
for recording.)
Main Power switch: This mechanical switch turns the AVR’s power supply on or off. It is
usually left on and cannot be turned on or off using the remote control.
12V Trigger connector: This connector provides 12V DC whenever the AVR is on. It can
be used to turn on and off other devices such as a powered subwoofer.
AC Input connector: After you have made all other connections, plug the supplied AC
power cord into this receptacle and into an unswitched wall outlet.
Harman Kardon
AVR 165/230V Service Manual
Page 6 of 111

8
AVR 1650/AVR 165 System Remote Control Functions
System Remote Control Functions
IR Transmitter Lens
Mute Button
Source Selector Buttons
Volume Up/Down Buttons
Speaker Setup Buttons
OK Button
Delay Button
Number Buttons
Memory Button
Macro Buttons
Transport Control Buttons
Display Dimmer Button
Disc Skip Button (AVR 1650)
RDS Button (AVR 165)
Preset Station Up/Down Buttons
Clear Button
Left/Right/Up/Down Buttons
Program Indicator LED
AVR Button
Sleep/CH Up/Down Buttons
OSD Button
Channel Level Control Button
Digital Input Button
Tuning Mode Button
Direct Station Entry Button
Tuning Up/Down Buttons
Tone Control Button
Night Mode Button
Track Skip Up/Down Buttons
Test Tone Button
Power Off Button
Power On Button
Harman Kardon
AVR 165/230V Service Manual
Page 7 of 111

9
AVR 1650/AVR 165
ENGLISH
System Remote Control Functions, continued
System Remote Control Functions, continued
In addition to controlling the AVR, the AVR remote is capable of controlling nine other
devices, including an iPod/iPhone device docked in a The Bridge IIIP docking station
connected to the AVR. During the installation process, you may program the codes for
each of your source components into the remote. (See Program the Remote to Control
Your Source Devices and TV, on page 16, for programming information.) To operate a
component, press its Source Selector button to change the remote’s control mode.
A button’s function depends on which component is being controlled. See Table A10 in
the Appendix for listings of the functions for each type of component. Most of the buttons
on the remote have dedicated functions, although the precise codes transmitted vary
depending on the specific device being controlled. Due to the wide variety of functions
for various source devices, we have included only a few of the most often-used functions
on the remote: alphanumeric keys, transport controls, television-channel control, menu
access and power on and off. To return the remote to the AVR control mode at any time,
press the AVR button.
IR Transmitter lens: As buttons are pressed on the remote, infrared codes are emitted
through this lens.
Program Indicator LED: This LED lights up to indicate various procedures when the
remote is in the Programming mode.
Power On/Off buttons: Press these buttons to turn theAVR or the device being controlled
on and off. The Main Power switch on the AVR’s rear panel must be on for this button to
turn the AVR on and off.
Mute button: Press this button to mute the AVR’s speaker-output connectors and
Headphone jack. To restore the sound, press this button or adjust the volume.
AVR button: Press this button to switch the remote’s control mode to operate the AVR.
Source Selector buttons: Press one of these buttons to select a source device, e.g.,
DVD, AM/FM radio, etc. This action will also turn on the AVR and switch the remote’s
control mode to operate the selected source device. NOTE: The first press of the Radio
Source Selector button switches the AVR to the last-used tuner band (AM or FM). Each
successive press changes the band.
Test Tone button: Press this button to activate the test tone for calibrating channel
volume levels by ear.
Sleep button/Channel Up/Down buttons: Press the Sleep button to activate the sleep
timer, which turns off the AVR after a programmed period of time of up to 90 minutes.The
Channel Up/Down buttons have no effect on the AVR but are used to change channels on
TVs and some video sources.
Volume Up/Down buttons: Press these buttons to raise or lower the volume.
OSD button: Press this button to activate the on-screen display menu system.
Channel Level Control button: Press this button to activate the individual channel-level
adjustment. It lets you easily change the channel balance to suit different programs or
seating arrangements. See
Manual Speaker Setup, on page 21, for more information.
Speaker Setup button: Press this button to configure which speakers are included in
your system. See
Manual Speaker Setup, on page 21, for more information.
OK button: This button is used to select items from the menu system.
Digital Input button: Press this button to select the specific digital audio input (or
analog audio input) to which the current source is connected.
Delay button: Pressing this button lets you adjust two different types of delay settings
(use the Up/Down buttons to cycle through the settings):
A/V Sync:This setting lets you resynchronize the audio and video signals from a source•
to eliminate a “lip sync” problem. Lip-sync issues can occur when the video portion
of a signal undergoes additional processing in either the source device or the video
display. Use the Left/Right buttons to delay the audio by up to 180ms.
Front L/Center/Front R/Surr R/Surr L/Subwoofer: These settings let you set the delay•
for each speaker to compensate for the different distances they may be from the
listening position. Use the Up/Down buttons to cycle through each of the system’s
speakers, and use the Left/Right buttons to set the distance each speaker is from
the listening position. See
Manual Speaker Setup, on page 21, for more information.
Left/Right/Up/Down buttons: These buttons are used to navigate the menu system.
Number buttons: Use these buttons to enter numbers for radio-station frequencies or
to select station presets.
Tuning Mode button: Press this button to toggle the radio between manual (one
frequency step at a time) and automatic (seeks frequencies with acceptable signal
strength) tuning mode. It also toggles between stereo and mono modes when an FM
station is tuned in.
Memory button: To save the currently tuned radio station as a preset, press this button,
then a Number button.
Direct Station Entry button: Press this button before using the Number buttons to enter
a radio station frequency.
Clear button: Press this button to clear a radio station frequency you have started to
enter.
Tuning Up/Down buttons: Press these buttons to tune a radio station. Depending on
whether the tuning mode has been set to manual or automatic, each press will either
change one tuning frequency increment at a time or seek the next higher or lower
station with acceptable signal strength.
Preset Station Up/Down buttons: Press these buttons to cycle through your preset
radio stations.
Tone Control button: Press this button to access the bass and treble controls. Use
the OK button to select an adjustment and use the Up/Down buttons to change the
settings.
Disc Skip button (AVR 1650): This button is used with some optical disc changers to
skip to the next disc.
RDS button (AVR 165): When listening to an FM radio station that broadcasts RDS
information, this button activates the various RDS functions.
Night Mode button: Press this button to activate Night mode with specially encoded
Dolby Digital discs or broadcasts. Night mode compresses the audio so that louder
passages are reduced in volume to avoid disturbing others, while dialogue remains
intelligible. Each press of the button advances through the following settings:
Off: No compression is applied. Loud passages in the program remain as they were•
recorded.
Mid: Loud passages in the program are reduced moderately in volume.•
Max: Loud passages in the program are reduced more in volume.•
Macro buttons: These buttons may be programmed to execute a series of up to 19
commands with a single button press. They are useful for programming the command
to turn on or off all of your components or for accessing specialized functions for a
different component from the one that you are currently operating. See
Programming
Macro Commands, on page 24, for information about programming macros.
Track Skip Up/Down buttons: These buttons have no effect on the AVR but are used
with many source components to change tracks or chapters.
Display Dimmer button: Press this button to dim the AVR’s front-panel display partially
or fully.
Transport Control buttons: These buttons have no effect on the AVR but are used to
control many source components. By default, when the remote is operating the AVR,
these buttons will control a Harman Kardon Blu-ray Disc player or DVD player.
Harman Kardon
AVR 165/230V Service Manual
Page 8 of 111

24
AVR 1650/AVR 165 Advanced Functions, continued
Advanced Remote Control Programming
Remote Channel-Control Punch-Through
The punch-through feature allows you to operate one component while setting certain
groups of controls to operate another component. For example, while using the AVR
controls for surround modes and other audio functions, you may also use the remote
to operate the transport controls of your Blu-ray Disc player. Or while using the remote
to control video functions on your TV, you may also use the remote to change channels
on your cable box.
To program punch-through control while operating any device:
For three seconds, press and hold the Source Selector button (or the AVR button) for1.
the main device the remote will be operating. The Program Indicator LED will flash,
indicating that the remote is in Program mode and that you may release the button.
Select the type of punch-through programming.2.
To program volume-control punch-through, press the Volume Up button.a)
To program channel-control punch-through, press the Volume Down button.b)
To program transport-control punch-through, press the Play transport-control button.c)
Press the Source Selector button for the device whose volume, channel or transport-3.
controls you will use while operating the device selected in the first step. The Program
Indicator LED will flash to confirm.
To undo punch-through programming, follow the same steps as above, but press the
same Source Selector button in Steps 1 and 3.
You may reassign the transport-control punch-through programming for the AVR, VID2
and VID3 devices to another device, such as a CD player. If you wish to remove transport-
control punch-through altogether for the AVR, VID2 or VID3 device, follow the same
procedure as for programming punch-through, but in Step 3 press either of the other
two of these three special selector buttons. For example, to remove transport-control
punch-through from the VID3 device so that pressing any of the transport controls will
have no effect, press and hold the VID3 Button until the Program Indicator LED flashes,
then press the Play Button, followed by either the AVR or VID2 Button.
Programming Macro Commands
Each of the AVR remote’s four Macro buttons and the Power On button (see
System
Remote Control Functions, on pages 8 and 9) can be programmed to send out up to
19 commands at one time from a single button push. Any AVR remote control button’s
function from any mode (except the Mute button, the Dim button and the Channel Up/
Down buttons) can be programmed into a macro.
NOTE: Use caution when programming complicated macros. It isn’t possible to program
a pause or delay before sending additional commands after a “Power On” command,
and the component may not be ready to respond to commands immediately after
powering on.
To program a macro:
Simultaneously press one of the four Macro buttons, or the Power On button, and the1.
Mute button to enter the Programming mode.
Press in up to 19 commands that you want stored in that Macro button. Press the Source2.
Selector button for each device (or AVR button for the AVR itself) before you enter
individual commands. This step counts as one of the 19 commands allowed for each
Macro.
For the Power On command, DO NOT press the Power On button. Press the Mute button3.
instead.
Press the Power Off button to program the Power Off command.4.
Press the Sleep button to end the programming process.5.
It isn’t possible to “edit” a command within a macro. However, you may erase the macro
as follows:
Simultaneously press and hold the Mute button and the Macro button containing the1.
macro until the Program Indicator LED flashes.
Press the Channel Down button to erase the macro.2.
To execute a macro, press the Macro button (or the Power On button) into which you
programmed the macro.
Recording
Two-channel analog and digital audio signals, as well as composite video signals, are
normally available at the appropriate recording output connectors. To make a recording,
connect your audio or video recorder to the appropriate AVR output connectors as
described in the Making Connections section, insert blank media in the recorder and
make sure the recorder is turned on and recording while the source is playing. Refer to
the recording device’s instructions for complete information about making recordings.
NOTES:
The AVR does not convert analog signals to digital or vice versa.1.
Only PCM digital audio signals are available for recording. Proprietary formats such as2.
the Dolby Digital and DTS bitstreams may not be recorded using the digital audio
connections. Use the analog audio connections to make an analog recording.
HDMI and component video sources are not available for recording.3.
Please make certain that you are aware of any copyright restrictions on any material you4.
record. Unauthorized duplication of copyrighted materials is prohibited by law.
Sleep Timer
The sleep timer sets the AVR to play for up to 90 minutes and then turn off automatically.
Press the Sleep button on the remote, and the time until turn-off will be displayed on the
front-panel Message display and on a connected TV. Each additional press of the Sleep
button decreases the play time by 10 minutes, with a maximum of 90 minutes. The
SLEEP OFF setting disables the sleep timer.
When the sleep timer has been set, the front-panel display will automatically dim to
half brightness.
If you press the Sleep button after the timer has been set, the remaining play time will
be displayed. Press the Sleep button again to change the play time.
Resetting the Remote
To reset the remote to its factory-default condition, simultaneously press and hold any
Source Selector button and the “0” Number button. When the Program Indicator LED
flashes amber, enter the code “333.” When the green LED goes out, the remote control
will be reset.
Processor Reset
If the AVR behaves erratically after a power surge, first turn off the rear-panel Main
Power switch and unplug the AC power cord for at least 3 minutes. Plug the cord back
in and turn the AVR on. If this procedure doesn’t help, reset the AVR’s processor as
described below.
NOTE: A processor reset erases all user configurations, including video resolution,
speaker and level settings, and tuner presets. After a reset, reenter all of these settings
from your notes in the Appendix worksheets.
To reset the AVR’s processor:
Press the front-panel Standby/On switch to place the unit in the Standby mode (the1.
Power Indicator LED will turn amber).
Press and hold the front-panel Surround Mode button for at least 5 seconds until the2.
RESET message appears on the front-panel Message display.
If the AVR does not function correctly after a processor reset, contact an authorized
Harman Kardon service center for assistance. Authorized service centers may be located
by visiting our Web site at www.harmankardon.com.
Memory
If the AVR is unplugged or experiences a power outage, it will retain your user settings
for up to four weeks.
Harman Kardon
AVR 165/230V Service Manual
Page 9 of 111

25
AVR 1650/AVR 165
ENGLISH
Troubleshooting
Symptom
Cause Solution
Unit does not function when Main Power switch is
turned on
No AC power•Ensure that the power cord is plugged into a live AC•
power outlet
Check if the AC outlet is switch-controlled•
Front-panel Message display lights, but there's no
sound or picture
Intermittent input connection•
Mute is on•
Volume control is turned down•
Secure all input and speaker connections•
Press Mute button•
Turn up Volume control•
No sound from any speaker; PROTECT message
appears on Message display
Amplifier is in protection mode due to possible short•
circuit
Amplifier is in protection mode due to internal problems•
Check all speaker wires at speaker and AVR•
connections for crossed wires
Contact your local Harman Kardon service center•
No sound from center or surround speakers Incorrect surround mode•
Program material is monophonic•
Incorrect speaker configuration•
Program material is stereo•
Select a surround mode other than stereo•
Mono programs contain no surround information•
Check the speaker configuration in the setup menu•
The surround decoder may not create center- or•
surround-channel information from nonencoded stereo
programs
Unit does not respond to remote control commands Weak batteries in remote•
AVR not selected•
Remote sensor is obscured•
Change batteries in remote•
Press the Setup/AVR button•
Ensure that the AVR’s front-panel remote sensor is in•
the line of sight of the remote
Intermittent buzzing in tuner Local interference•Move the AVR or antenna away from computers,•
fluorescent lights, motors or other electrical appliances
Unable to activate remote control Programming mode Source Selector button is not held for at least 3 seconds•Be sure to hold the Source Selector button for at least•
3 seconds
Additional information on troubleshooting possible problems with your AVR and installation-related issues may be found in the list of “Frequently Asked Questions,” which is located in the Product
Support section of our Web site: www.harmankardon.com
Troubleshooting
Harman Kardon
AVR 165/230V Service Manual
Page 10 of 111

26
AVR 1650/AVR 165 Specifications
Specifications
Audio Section
Stereo power: 95W per channel, two
channels driven @ 8 ohms,
20Hz – 20kHz, <0,07%
THD
Multichannel power: 95W per channel, two
channels driven @ 8 ohms,
20Hz – 20kHz, <0,07%
THD
Input sensitivity/impedance: 200mV/47k ohms
Signal-to-noise ratio (IHF-A): 100dB
Surround system adjacent-channel separation: Dolby Pro Logic/PLII: 40dB
Dolby Digital: 55dB
DTS: 55dB
Frequency response: 10Hz – 130kHz
(+0dB/–3dB)
High instantaneous-current capability (HCC): ±25 amps
Transient intermodulation distortion (TIM): Unmeasurable
Slew rate: 40V/µsec
FM Tuner Section
Frequency range: 87.5 – 108.0MHz
Usable sensitivity IHF: 1.3µV/13.2dBf
Signal-to-noise ratio (mono/stereo): 70dB/68dB
Distortion (mono/stereo): 0.2%/0.3%
Stereo separation: 40dB @ 1kHz
Selectivity (±400kHz): 70dB
Image rejection: 80dB
IF rejection: 90dB
AM Tuner Section
Frequency range: 520 – 1720kHz
Signal-to-noise ratio: 45dB
Usable sensitivity (loop): 500µV
Distortion (1kHz, 50% mod): 0.8%
Selectivity (±10kHz): 30dB
Video Section
Television format: NTSC (AVR 1650);
PAL (AVR 165)
Input level/impedance: 1Vp-p/75 ohms
Output level/impedance: 1Vp-p/75 ohms
Video frequency response (composite video): 10Hz – 8MHz (–3dB)
HDMI: Version 1.4a with 12-bit
Deep Color
General Specifications
Power requirement: 120V AC/60Hz
(AVR 1650);
220V – 240V AC/50Hz – 60Hz
(AVR 165)
Power consumption: <0.5W (standby);
280W maximum
Dimensions (W x H x D) 17-5/16" x 6-1/2" x 17-1/8"
(440mm x 165mm x 435mm)
Weight 20 lb (9.1kg)
Harman Kardon
AVR 165/230V Service Manual
Page 11 of 111

27
AVR 1650/AVR 165
ENGLISH
Source DVD HDMI 1 HDMI 2 HDMI 3 HDMI 4 Video 1 Video 2 Bridge Aux CD Tape Tuner TV
Title BRIDGE TUNER
Audio Input COAX 1 HDMI HDMI HDMI HDMI ANALOG OPTICAL
1
THE
BRIDGE
IIIP
ANALOG ANALOG ANALOG INT.
TUNER
OPTICAL
1
Auto Poll ON OFF OFF OFF OFF OFF ON – – OFF OFF ON – – OFF
Surround Mode LOGIC 7
MOVIE
LOGIC 7
MOVIE
LOGIC 7
MOVIE
LOGIC 7
MOVIE
LOGIC 7
MOVIE
LOGIC 7
MOVIE
LOGIC 7
MOVIE
LOGIC 7
MOVIE
LOGIC 7
MOVIE
LOGIC 7
MOVIE
LOGIC 7
MOVIE
LOGIC 7
MOVIE
LOGIC 7
MOVIE
Table A2 – Source Setting Defaults
Device Type AVR Source Audio Connections Video Connections
Cable TV, Satellite, HDTV or other device that
delivers television programs
Video 1 Video 1 Analog inputs•
Optical 1 Input (if not in use with HDMI 3•
Composite Video 1 Input
VCR, DVR, PVR, or other audio/video recorder Video 2 Video 2 Analog (inputs and outputs)•
Any one available coaxial or optical digital audio•
input with corresponding coax digital output
Composite Video 2 Input•
For recording, use Composite Video 2 Output•
DVD player, Blu-ray Disc player DVD or HDMI (for
Blu-ray Disc)
DVD Analog Inputs•
Coax 1 Input•
DVD Component Video Input•
HDMI-capable disc player, game console or
other audio/video device
HDMI 1 HDMI 1 Input•HDMI 1 Input•
HDMI-capable disc player, game console or
other audio/video device
HDMI 2 HDMI 2 Input•HDMI 2 Input•
HDMI-capable disc player, game console or
other audio/video device
HDMI 3 HDMI 3 Input•HDMI 3 Input•
HDMI-capable disc player, game console or
other audio/video device
HDMI 4 HDMI 4 Input•HDMI 4 Input•
Portable audio device AUX AUX Input on front panel•Not required•
CD player CD CD Analog Inputs•
Any one available coaxial or optical digital audio•
input
Not required•
CD-R, MiniDisc, cassette Tape Tape Analog (inputs and outputs)•
Any one available coaxial or optical digital audio•
input
Use corresponding optical digital output•
Not required•
iPod or iPhone Bridge The Bridge IIIP•Not required•
Note: The AVR is equipped with a total of three digital audio inputs. Certain digital audio connections are recommended simply because those digital audio inputs are assigned to those sources by
default at the factory. But any digital audio input may be reassigned to any source. Since you may not be using all of the AVR's sources, you may reassign a digital audio input that is recommended
for a source you aren’t using to another device. Table A1 is a guideline; you may need to make adjustments to fit your system.
Table A1 – Recommended Source Component Connections
Appendix – Default settings, worksheets, remote product codes
Appendix
Harman Kardon
AVR 165/230V Service Manual
Page 12 of 111

Harman Kardon
AVR 165/230V Service Manual
Page 13 of 111

Harman Kardon
AVR 165/230V Service Manual
Page 14 of 111

Harman Kardon
AVR 165/230V Service Manual
Page 15 of 111

AVR 165 (Basic) PARTS LIST
Level Ref# Component Description Drawing No REQ-Qty UM
0,2 CGB1A237Z BADGE , AVR165 1EA
0,2 CGL1A222 INDICATOR , VOLUME AVR130/230/330 1EA
0,2 CGR5A437 COVER , JACK B 1EA
0,2 CGU1A318Y ORNAMENT , VOLUME AVR255 1EA
0,2 CGU2A410A25K WINDOW , FIP 1EA
0,2 CGWAVR165/230 FRONT PANEL ASS'Y 1EA
..3 CBT2A1064 KNOB , STANDBY 1EA
..3 CBT2A1065 KNOB , BACK 1EA
..3 CGB3A158Z BADGE , HARMAN/KARDON (FRONT) 1EA
..3 CGL1A265Y INDICATOR , POWER AVR155 1EA
..3 CGW6A447RHSB24 PANEL , FRONT AVR1650 1EA
..3 CMC1A372 PLATE , SHIELD 1EA
..3
CMC1A416
PLATE , EARTH TOP
1
EA
..3
CMC1A416
PLATE , EARTH TOP
1
EA
..3 CMC2A326 PLATE , EARTH AVR350 1EA
..3 CMC3A338 PLATE , EARTH 2EA
..3 CMD2A443 BRACKET , SIDE 2EA
..3 CMH1A297 HOLDER , USB 1EA
..3 CMH2A215 HOLDER , LED AVR350 1EA
..3 CMX1A291ZB24 SHEET , COVER 1EA
..3 CMZ1A127 FILTER , FIP AVR255 1EA
AVR165/230 FRONT PCB MANUAL ASS'Y
Level Ref# Component Description Drawing No REQ-Qty UM
..3 COP12357G AVR165/230 FRONT PCB MANUAL ASS'Y 1EA
....5 C121 CCBS1H151KBT CAP , CERAMIC(150PF/50V) CH UP025 B151K-A-B Z 1EA
....5 C122 CCEA1AH331T CAP , ELECT(10V/330uF) KR3-10V331MB(6.3*11L) 1EA
....5 C151 CCFT1H473ZF CAP , CERAMIC 0.047UF 50V Z 1EA
....5
C152
CCEA1CKS100T
CAP , ELECT(16V/10uF)-S
KC3-16V100MA2(4*5L)
1
EA
....5
C152
CCEA1CKS100T
CAP , ELECT(16V/10uF)-S
KC3-16V100MA2(4*5L)
1
EA
....5 C161 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1EA
....5 C171 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1EA
....5 C181 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1EA
....5 C213 CCBS1H223ZFT CAP , CERAMIC(22000PF/50V) CH UP025 F223Z-A-B J 1EA
....5 C214 CCBS1H223ZFT CAP , CERAMIC(22000PF/50V) CH UP025 F223Z-A-B J 1EA
....5 C252 CCEA1HKS2R2T CAP , ELECT(50V/2.2uF)-S KC3-50V2R2MA2(4*5L) 1EA
....5 C311 CCBS1H102KBT CAP , CERAMIC(1000PF/50V) CH UP025 B102K-A-B Z 1EA
....5 C322 CCBS1H102KBT CAP , CERAMIC(1000PF/50V) CH UP025 B102K-A-B Z 1EA
....5 C412 CCBS1H103ZFT CAP , CERAMIC 0.01UF 50V Z 1EA
....5 C413 CCEA1JH470TS CAP , ELECT 63V/47UF/105'C 1EA
....5 C414 CCEA1JH470TS CAP , ELECT 63V/47UF/105'C 1EA
....5 C415 CCBS1H103ZFT CAP , CERAMIC 0.01UF 50V Z 1EA
....5 C422 CCEA1HH4R7T CAP , ELECT(50V/4.7uF) KR3-50V4R7MA(5*11L) 1EA
....5 C431 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1EA
....5 C441 CCBS1H223ZFT CAP , CERAMIC(22000PF/50V) CH UP025 F223Z-A-B J 1EA
....5 C442 CCBS1H223ZFT CAP , CERAMIC(22000PF/50V) CH UP025 F223Z-A-B J 1EA
....5 C504 CCBS1H103ZFT CAP , CERAMIC 0.01UF 50V Z 1EA
....5 C511 CCBS1H560JT CAP , CERAMIC(56PF/50V) CH UP025SL560J-A-B Z 1EA
....5 C512 CCBS1H560JT CAP , CERAMIC(56PF/50V) CH UP025SL560J-A-B Z 1EA
....5 C521 CCEA1AH101T CAP , ELECT(10V/100uF) KR3-10V101MA(5*11L) 1EA
....5 C522 CCBS1H103ZFT CAP , CERAMIC 0.01UF 50V Z 1EA
....5 C533 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1EA
....5 C553 CCBS1H101KBT CAP , CERAMIC(100PF/50V) CH UP025 B101K-A-B Z 1EA
....5 C554 CCBS1H101KBT CAP , CERAMIC(100PF/50V) CH UP025 B101K-A-B Z 1EA
....5 C631 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1EA
....5 C651 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1EA
....5 C652 CCBS1H471KBT CAP , CERAMIC(470PF/50V) CH UP025 B471K-A-B Z 1EA
....5 C653 CCBS1H471KBT CAP , CERAMIC(470PF/50V) CH UP025 B471K-A-B Z 1EA
....5 C714 CCBS1H223ZFT CAP , CERAMIC(22000PF/50V) CH UP025 F223Z-A-B J 1EA
....5 C715 CCEA1CKS100T CAP , ELECT(16V/10uF)-S KC3-16V100MA2(4*5L) 1EA
....5
C721
CCEA1HKS2R2T
CAP , ELECT(50V/2.2uF)-S
KC3-50V2R2MA2(4*5L)
1
EA
....5
C721
CCEA1HKS2R2T
CAP , ELECT(50V/2.2uF)-S
KC3-50V2R2MA2(4*5L)
1
EA
....5 C731 CCEA1AH471T CAP , ELECT(10V/470uF) KR3-10V471MB(6.3*11L) 1EA
....5 C732 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1EA
....5 C751 CCBS1C222MXT CAP , CERAMIC(2200PF/16V) CH EP025 B222M-A-B J 1EA
....5 C752 CCBS1H102KBT CAP , CERAMIC(1000PF/50V) CH UP025 B102K-A-B Z 1EA
....5 C753 CCBS1H102KBT CAP , CERAMIC(1000PF/50V) CH UP025 B102K-A-B Z 1EA
....5 C754 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1EA
....5 C801 CCEA1EH470T CAP , ELECT(25V/47uF) KR3-25V470MA(5*11L) 1EA
....5 C802 CCEA1EH470T CAP , ELECT(25V/47uF) KR3-25V470MA(5*11L) 1EA
....5 C811 CCEA1HH100T CAP , ELECT(50V/10uF) KR3-50V100MA(5*11L) 1EA
....5 C813 CCBS1H470JT CAP , CERAMIC(47PF/50V) CH UP025SL470J-A-B Z 1EA
....5 C821 CCBS1H471KBT CAP , CERAMIC(470PF/50V) CH UP025 B471K-A-B Z 1EA
....5 C822 CCBS1H151KBT CAP , CERAMIC(150PF/50V) CH UP025 B151K-A-B Z 1EA
....5 C823 CCEA1HH100T CAP , ELECT(50V/10uF) KR3-50V100MA(5*11L) 1EA
....5 C830 CCBS1H473ZFT CAP , CERAMIC(47000PF/50V) CH UP025 F473Z-A-B J 1EA
....5
C901
CCEA1HH100T
CAP , ELECT(50V/10uF)
KR3-50V100MA(5*11L)
1
EA
....5
C901
CCEA1HH100T
CAP , ELECT(50V/10uF)
KR3-50V100MA(5*11L)
1
EA
....5 C902 CCEA1HH100T CAP , ELECT(50V/10uF) KR3-50V100MA(5*11L) 1EA
....5 C911 CCEA1EH470T CAP , ELECT(25V/47uF) KR3-25V470MA(5*11L) 1EA
....5 C912 CCEA1EH470T CAP , ELECT(25V/47uF) KR3-25V470MA(5*11L) 1EA
....5 C923 CCBS1H681KBT CAP , CERAMIC(680PF/50V) CH UP025 B681K-A-B Z 1EA
....5 C924 CCBS1H681KBT CAP , CERAMIC(680PF/50V) CH UP025 B681K-A-B Z 1EA
....5 C931 CCEA1CH331T CAP , ELECT(16V/330uF) KR3-16V331MC(8*11.5L) 1EA
....5 C932 CCEA1CH331T CAP , ELECT(16V/330uF) KR3-16V331MC(8*11.5L) 1EA
Harman Kardon
AVR 165/230V Service Manual
Page 16 of 111

AVR165/230 FRONT PCB MANUAL ASS'Y
Level Ref# Component Description Drawing No REQ-Qty UM
....5 D161 HVD1N5819T DIODE , SCHOTTKY 1N5819 1EA
....5 D401 CVD1N4003ST DIODE , RECT 1N4003 1EA
....5 D412 CVDZJ8.2BT DIODE , ZENER 8.2V ZJ8.2B 1/2W 1EA
....5 D413 HVDMTZJ27BT DIODE , ZENER MTZJ27B 1/2W 1EA
....5 D421 CVDZJ6.8BT DIODE , ZENER 6.8V ZJ6.8B 1/2W 1EA
....5 D422 CVDZJ6.8BT DIODE , ZENER 6.8V ZJ6.8B 1/2W 1EA
....5 D455 HVD1SS133MT DIODE 1SS133T-77 1EA
....5 D531 HVD1SS133MT DIODE 1SS133T-77 1EA
....5 D532 HVD1SS133MT DIODE 1SS133T-77 1EA
....5 D533 HVD1SS133MT DIODE 1SS133T-77 1EA
....5 D534 HVD1SS133MT DIODE 1SS133T-77 1EA
....5 D631 HVD1SS133MT DIODE 1SS133T-77 1EA
....5 D632 HVD1SS133MT DIODE 1SS133T-77 1EA
....5
L151
HLQ02C100KT
COIL , AXAIL (10UH)
1
EA
....5
L151
HLQ02C100KT
COIL , AXAIL (10UH)
1
EA
....5 Q104 CVTKTC1027YT T.R , KTC1027Y KTC1027Y/TO-92L/KEC 1EA
....5 Q111 HVTKRA107MT T.R , TO-92M KRA107M 1EA
....5 Q112 HVTKRC107MT T.R , TO-92M KRC107M 1EA
....5 Q113 HVTKRC107MT T.R , TO-92M KRC107M 1EA
....5 Q251 HVTKTA1271YT T.R KTA1271Y 1EA
....5 Q252 HVTKRC107MT T.R , TO-92M KRC107M 1EA
....5 Q721 HVTKRC107MT T.R , TO-92M KRC107M 1EA
....5 Q906 HVTKRA107MT T.R , TO-92M KRA107M 1EA
....5 Q907 HVTKRA107MT T.R , TO-92M KRA107M 1EA
....5 Q941 HVTKTC2874BT T.R , MUTE KTC2874B 1EA
....5 Q942 HVTKTC2874BT T.R , MUTE KTC2874B 1EA
....5 Q943 HVTKTC2874BT T.R , MUTE KTC2874B 1EA
....5 Q944 HVTKTC2874BT T.R , MUTE KTC2874B 1EA
....5 Q951 HVTKRC107MT T.R , TO-92M KRC107M 1EA
....5
Q952
HVTKRA107MT
T.R , TO-92M
KRA107M
1
EA
....5
Q952
HVTKRA107MT
T.R , TO-92M
KRA107M
1
EA
....5 Q954 HVTKRC107MT T.R , TO-92M KRC107M 1EA
....5 R101 CRD20TF2200T RES , CARBON(220 OHM, 1%) 1EA
....5 R102 CRD20TF6800T RES , CARBON(680 OHM, 1%) 1EA
....5 R113 CRD20TJ102T RES, CARBON(1/5W,1Kohm,J) 1EA
....5 R122 CRD20TJ100T RES, CARBON(1/5W,10ohm,J) 1EA
....5 R201 CRD20TJ101T RES, CARBON(1/5W,100ohm,J) 1EA
....5 R202 CRD20TJ101T RES, CARBON(1/5W,100ohm,J) 1EA
....5 R203 CRD20TJ101T RES, CARBON(1/5W,100ohm,J) 1EA
....5 R211 CRD20TJ101T RES, CARBON(1/5W,100ohm,J) 1EA
....5 R213 CRD20TJ272T RES, CARBON(1/5W,2.7Kohm,J) 1EA
....5 R214 CRD20TJ272T RES, CARBON(1/5W,2.7Kohm,J) 1EA
....5 R251 CRD20TJ222T RES, CARBON(1/5W,2.2Kohm,J) 1EA
....5 R252 CRD25TJ393T RES, CARBON(1/4W,39Kohm,J) 1EA
....5 R312 CRD20TF1001T RES , CARBON 1K /1/5W /F 1EA
....5
R313
CRD20TF1501T
RES , CARBON
1.5K /1/5W /F
1
EA
....5
R313
CRD20TF1501T
RES , CARBON
1.5K /1/5W /F
1
EA
....5 R314 CRD20TF1801T RES , CARBON 1.8K /1/5W /F 1EA
....5 R315 CRD20TF2701T RES , CARBON 2.7K /1/5W/F 1EA
....5 R316 CRD20TF3301T RES , CARBON 3.3K /1/5W/F 1EA
....5 R322 CRD20TF1001T RES , CARBON 1K /1/5W /F 1EA
....5 R323 CRD20TF1501T RES , CARBON 1.5K /1/5W /F 1EA
....5 R324 CRD20TF1801T RES , CARBON 1.8K /1/5W /F 1EA
....5 R325 CRD20TF2701T RES , CARBON 2.7K /1/5W/F 1EA
....5 R326 CRD20TF3301T RES , CARBON 3.3K /1/5W/F 1EA
....5 R327 CRD20TF5601T RES , CARBON(5.6K/F) 1EA
....5 R328 CRD20TF5601T RES , CARBON(5.6K/F) 1EA
....5 R401 CRD25FJ3R3T RES , CARBON 3.3 OHM 1/4W J 1EA
....5 R402 CRD25TJ5R6T RES, CARBON(1/4W,5.6ohm,J) 1EA
....5 R403 CRD20TJ100T RES, CARBON(1/5W,10ohm,J) 1EA
....5 R404 CRD25TJ5R6T RES, CARBON(1/4W,5.6ohm,J) 1EA
....5 R411 CRD20TJ104T RES, CARBON(1/5W,100Kohm,J) 1EA
....5 R412 CRD20TJ122T RES, CARBON(1/5W,1.2Kohm,J) 1EA
....5 R413 CRD20TJ104T RES, CARBON(1/5W,100Kohm,J) 1EA
....5 R415 CRD20TJ473T RES, CARBON(1/5W,47Kohm,J) 1EA
....5 R431 CRD20TJ100T RES, CARBON(1/5W,10ohm,J) 1EA
....5 R432 CRD20TJ100T RES, CARBON(1/5W,10ohm,J) 1EA
....5 R511 CRD20TJ100T RES, CARBON(1/5W,10ohm,J) 1EA
....5 R512 CRD20TJ100T RES, CARBON(1/5W,10ohm,J) 1EA
....5 R513 CRD20TJ153T RES, CARBON(1/5W,15Kohm,J) 1EA
....5 R514 CRD20TJ153T RES, CARBON(1/5W,15Kohm,J) 1EA
....5 R551 CRD20TJ471T RES, CARBON(1/5W,470ohm,J) 1EA
....5 R552 CRD20TJ471T RES, CARBON(1/5W,470ohm,J) 1EA
....5 R553 CRD20TJ104T RES, CARBON(1/5W,100Kohm,J) 1EA
....5 R554 CRD20TJ104T RES, CARBON(1/5W,100Kohm,J) 1EA
....5 R701 CRD20TJ102T RES, CARBON(1/5W,1Kohm,J) 1EA
....5 R702 CRD20TJ102T RES, CARBON(1/5W,1Kohm,J) 1EA
....5
R703
CRD20TJ102T
RES, CARBON(1/5W,1Kohm,J)
1
EA
....5
R703
CRD20TJ102T
RES, CARBON(1/5W,1Kohm,J)
1
EA
....5 R711 CRD20TJ470T RES, CARBON(1/5W,47ohm,J) 1EA
....5 R712 CRD20TJ470T RES, CARBON(1/5W,47ohm,J) 1EA
....5 R713 CRD20TJ470T RES, CARBON(1/5W,47ohm,J) 1EA
....5 R721 CRD20TJ103T RES, CARBON(1/5W,10Kohm,J) 1EA
....5 R722 CRD20TJ101T RES, CARBON(1/5W,100ohm,J) 1EA
....5 R731 CRD20TJ100T RES, CARBON(1/5W,10ohm,J) 1EA
....5 R735 CRD20TJ152T RES, CARBON(1/5W,1.5Kohm,J) 1EA
Harman Kardon
AVR 165/230V Service Manual
Page 17 of 111

AVR165/230 FRONT PCB MANUAL ASS'Y
Level Ref# Component Description Drawing No REQ-Qty UM
....5 R741 CRD20TJ123T RES, CARBON(1/5W,12Kohm,J) 1EA
....5 R742 CRD20TJ102T RES, CARBON(1/5W,1Kohm,J) 1EA
....5 R801 CRD20TJ101T RES, CARBON(1/5W,100ohm,J) 1EA
....5 R802 CRD20TJ101T RES, CARBON(1/5W,100ohm,J) 1EA
....5 R811 CRD20TJ104T RES, CARBON(1/5W,100Kohm,J) 1EA
....5 R812 CRD20TJ102T RES, CARBON(1/5W,1Kohm,J) 1EA
....5 R813 CRD20TJ103T RES, CARBON(1/5W,10Kohm,J) 1EA
....5 R821 CRD20TJ102T RES, CARBON(1/5W,1Kohm,J) 1EA
....5 R822 CRD20TJ103T RES, CARBON(1/5W,10Kohm,J) 1EA
....5 R823 CRD20TJ104T RES, CARBON(1/5W,100Kohm,J) 1EA
....5 R834 CRD20TJ222T RES, CARBON(1/5W,2.2Kohm,J) 1EA
....5 R835 CRD20TJ103T RES, CARBON(1/5W,10Kohm,J) 1EA
....5 R836 CRD20TJ152T RES, CARBON(1/5W,1.5Kohm,J) 1EA
....5
R901
CRD25TJ101T
RES, CARBON(1/4W,100ohm,J)
1
EA
....5
R901
CRD25TJ101T
RES, CARBON(1/4W,100ohm,J)
1
EA
....5 R902 CRD20TJ101T RES, CARBON(1/5W,100ohm,J) 1EA
....5 R911 CRD20TJ101T RES, CARBON(1/5W,100ohm,J) 1EA
....5 R912 CRD20TJ101T RES, CARBON(1/5W,100ohm,J) 1EA
....5 R921 CRD20TJ102T RES, CARBON(1/5W,1Kohm,J) 1EA
....5 R922 CRD20TJ102T RES, CARBON(1/5W,1Kohm,J) 1EA
....5 R923 CRD20TJ152T RES, CARBON(1/5W,1.5Kohm,J) 1EA
....5 R924 CRD20TJ152T RES, CARBON(1/5W,1.5Kohm,J) 1EA
....5 R925 CRD20TJ104T RES, CARBON(1/5W,100Kohm,J) 1EA
....5 R926 CRD20TJ104T RES, CARBON(1/5W,100Kohm,J) 1EA
....5 R931 CRD20TJ104T RES, CARBON(1/5W,100Kohm,J) 1EA
....5 R932 CRD20TJ104T RES, CARBON(1/5W,100Kohm,J) 1EA
....5 R933 CRD20TJ221T RES, CARBON(1/5W,220ohm,J) 1EA
....5 R934 CRD20TJ221T RES, CARBON(1/5W,220ohm,J) 1EA
....5 R935 CRD20TJ221T RES, CARBON(1/5W,220ohm,J) 1EA
....5
R936
CRD20TJ221T
RES, CARBON(1/5W,220ohm,J)
1
EA
....5
R936
CRD20TJ221T
RES, CARBON(1/5W,220ohm,J)
1
EA
....5 R941 CRD25TJ432T RES, CARBON(1/4W,4.3Kohm,J) 1EA
....5 R942 CRD20TJ472T RES, CARBON(1/5W,4.7Kohm,J) 1EA
....5 R943 CRD20TJ472T RES, CARBON(1/5W,4.7Kohm,J) 1EA
....5 R944 CRD20TJ472T RES, CARBON(1/5W,4.7Kohm,J) 1EA
....5 R951 CRD20TJ102T RES, CARBON(1/5W,1Kohm,J) 1EA
....5 R953 CRD20TJ362T RES, CARBON(1/5W,3.6Kohm,J) 1EA
....5 R954 CRD20TJ103T RES, CARBON(1/5W,10Kohm,J) 1EA
....5 S311 CST1A024ZT SW , TACT 1EA
....5 S312 CST1A024ZT SW , TACT 1EA
....5 S313 CST1A024ZT SW , TACT 1EA
....5 S314 CST1A024ZT SW , TACT 1EA
....5 S315 CST1A024ZT SW , TACT 1EA
....5 S316 CST1A024ZT SW , TACT 1EA
....5 S317 CST1A024ZT SW , TACT 1EA
....5
S318
CST1A024ZT
SW , TACT
1
EA
....5
S318
CST1A024ZT
SW , TACT
1
EA
....5 S319 CST1A024ZT SW , TACT 1EA
....5 S320 CST1A024ZT SW , TACT 1EA
....5 S321 CST1A024ZT SW , TACT 1EA
....5 S322 CST1A024ZT SW , TACT 1EA
....5 S323 CST1A024ZT SW , TACT 1EA
....5 S330 CST1A024ZT SW , TACT 1EA
...4 BK71 CMD1A572 BRACKET , FIP 1EA
...4 BK72 CMD1A572 BRACKET , FIP 1EA
...4 BN51 CWB1C005350BM001 Shield Wire ass'y 1EA
...4 BN52 CWB1C903400BM001 SHIELD WIRE ASS'Y (2.5mm, 400mm, 3pin) 1EA
...4 BN61 CJP06GB142ZB PIN HEADER(6P, 2.54mm) 1EA
...4 BN73 CJP06GB142ZB PIN HEADER(6P, 2.54mm) 1EA
...4 BN74 CWB1C005100BM WIRE ASS'Y(5P, 100MM) 1EA
...4 CN61 CJP06GA221ZB FEMALE HEADER (6P,2.54mm) , STRAIGHT TYPE FAS2851 1EA
...4 CN71 CJP05GB03ZY WAFER,YMAW025(2.5mm,ANGLE) 1EA
...4 CN72 CJP27GA285ZN WAFER,FPC 1.25mm,stright 1.25-2-NP 1EA
...4 CN73 CJP06GB143ZB FEMALE HEADER(6P, 2.54mm) 1EA
...4 CN74 CJP05GB03ZY WAFER,YMAW025(2.5mm,ANGLE) 1EA
...4 C411 CCEA1JH101E CAP , ELECT 100UF 63V 1EA
...4 D101 CVD1L0345W31BOCT201V L.E.D , WHITE CVD1L0345W31BOCT201 1EA
...4 D102 CVD30ASOGCAA-S7 L.E.D , ORANGE T0L-30ASOGCAA-S7 1EA
...4 D201 CVD1L0345W31BOCT201V L.E.D , WHITE CVD1L0345W31BOCT201 1EA
...4 D202 CVD1L0345W31BOCT201V L.E.D , WHITE CVD1L0345W31BOCT201 1EA
...4 D203 CVD1L0345W31BOCT201V L.E.D , WHITE CVD1L0345W31BOCT201 1EA
...4 FIP1 CFL162SD19GINK V.F.D , (FUTABA, 162-SD-19GINK) 162-SD-19GINK 1EA
...4 IC12 CRVKSM603TE5B SENSOR , REMOCON 1EA
...4 IC13 CVISN74ACT04DR I.C , HEX INVERTERS(SOIC/D-14P) SN74ACT04DR / TEXAS INSTRUMENT 1EA
...4 IC14 HVINJM2068MDTE1 I.C , OP AMP (JRC) NJM2068MD-TE1 1EA
...4 IC15 HVINJM4556AL I.C , HEADPHONE (JRC) NJM4556AL 1EA
...4 JK51 CJJ9X006Z JACK , USB STRAIGHT(BLACK) U250FD004BY/YUQIU 1EA
...4
JK52
CJJ4N094Z
JACK , RCA(2P, WH/RD, NO SHIELD)
RCA-251H-00A-01
1
EA
...4
JK52
CJJ4N094Z
JACK , RCA(2P, WH/RD, NO SHIELD)
RCA-251H-00A-01
1
EA
...4 JK63 CJJ2E026Z JACK, PHONES(6.35mm,SILVER) PJ-612A-51/YUQIU 1EA
...4 RL91 CSL4A016ZU RELAY,BC3-12H,DC12V,2C2P BC3-12H/HANDOUK 1EA
...4 VR74 CSR2A037Z ENCODER 1EA
..3 CPE1A009 SHEET , BLIND 1EA
..3 CTB3+10JR SCREW 28 EA
..3 CTWS3+10GR SCREW 1EA
..3 CN72 CWC4C4A27B250B08 CARD , CABLE (27P/1.25mm,/250mm) 27P/1.25MM/250MM 1EA
Harman Kardon
AVR 165/230V Service Manual
Page 18 of 111

AVR165/230 FRONT PCB MANUAL ASS'Y
Level Ref# Component Description Drawing No REQ-Qty UM
0,2 CGX1A338MBC63 CAP , VOLUME 1EA
0,2 CGX1A392C66 ORNAMENT , AL B AVR350 1EA
0,2 CGX3A390C66Z SHEET , AL FRONT AVR1650 1EA
0,2 CKC6B145S60 CABINET , TOP AVR350 1EA
0,2 CMH1A214 HOLDER , VOLUME AVR130/230/330 1EA
0,2 CMZ2A090 SHEET , VOLUME 1EA
0,2 CQB1A549Y LABEL , ATTENTION DVD48 1EA
0,2 CQB1A622 LABEL , SERIAL NO 1EA
0,2 CTB3+8JFZR SCREW 17 EA
0,2 CTB4+6FFZR SCREW 6EA
0,2 CUAAVR165/230 BOTTOM CHASSIS ASS'Y 1EA
..3 CHD1A012ZR SCREW , SPECIAL 2EA
..3 CHD1A023R SCREW , SPECIAL 4EA
..3
CHD1A065R
SCREW , FLAT(2.6X4)
2
EA
..3
CHD1A065R
SCREW , FLAT(2.6X4)
2
EA
..3 CHD4A012R SCREW , SPECIAL 4EA
..3 CHE170 HOLDER , PCB 2EA
..3 CHG1A113 RUBBER 3EA
..3 CHG1A160Z CUSHION , RUBBER 1EA
..3 CHG1A373 CUSHION , FOOT AVR350 4EA
..3 CHR301 CLAMPER 3EA
..3 CHS1A032 TAPE , HEMELON 4EA
..3 CKF5A444Y PANEL , REAR AVR165 1EA
..3 CKL1A094 FOOT , A AVR350 2EA
..3 CKL1A095 FOOT , B AVR350 2EA
AVR165/230 INPUT PCB ASS'Y
Level Ref# Component Description Drawing No REQ-Qty UM
..3 COP12358G AVR165/230 INPUT PCB ASS'Y 1EA
....6
C112
CCUS1H104KC
CAP, CHIP(1608, 50V/0.1uF)
1
EA
....6
C112
CCUS1H104KC
CAP, CHIP(1608, 50V/0.1uF)
1
EA
....6 C115 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C200 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C217 CCUS1H101JA CAP, CHIP(1608, 50V/100pF) 1EA
....6 C218 CCUS1H101JA CAP, CHIP(1608, 50V/100pF) 1EA
....6 C219 CCUS1H101JA CAP, CHIP(1608, 50V/100pF) 1EA
....6 C227 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C228 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C229 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C230 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C293 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C300 CCUS1H272KC CAP, CHIP(1608, 50V/2700pF) 1EA
....6 C301 CCUS1H272KC CAP, CHIP(1608, 50V/2700pF) 1EA
....6 C302 CCUS1H683KC CAP, CHIP(1608, 50V/0.068uF) 1EA
....6 C303 CCUS1H272KC CAP, CHIP(1608, 50V/2700pF) 1EA
....6
C304
CCUS1H272KC
CAP, CHIP(1608, 50V/2700pF)
1
EA
....6
C304
CCUS1H272KC
CAP, CHIP(1608, 50V/2700pF)
1
EA
....6 C305 CCUS1H272KC CAP, CHIP(1608, 50V/2700pF) 1EA
....6 C332 CCUS1H103KC CAP, CHIP(1608, 50V/0.01uF) 1EA
....6 C333 CCUS1H103KC CAP, CHIP(1608, 50V/0.01uF) 1EA
....6 C334 CCUS1H103KC CAP, CHIP(1608, 50V/0.01uF) 1EA
....6 C335 CCUS1H103KC CAP, CHIP(1608, 50V/0.01uF) 1EA
....6 C336 CCUS1H103KC CAP, CHIP(1608, 50V/0.01uF) 1EA
....6 C337 CCUS1H103KC CAP, CHIP(1608, 50V/0.01uF) 1EA
....6 C348 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C349 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C350 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C351 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C352 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C353 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C362 CCUS1H223KC CAP, CHIP(1608, 50V/0.022uF) 1EA
....6
C369
CCUS1H223KC
CAP, CHIP(1608, 50V/0.022uF)
1
EA
....6
C369
CCUS1H223KC
CAP, CHIP(1608, 50V/0.022uF)
1
EA
....6 C370 CCUS1H223KC CAP, CHIP(1608, 50V/0.022uF) 1EA
....6 C466 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C601 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C603 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C605 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C607 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C609 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C611 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C613 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C615 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C617 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C619 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C621 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C623 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C625 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6
C627
CCUS1H104KC
CAP, CHIP(1608, 50V/0.1uF)
1
EA
....6
C627
CCUS1H104KC
CAP, CHIP(1608, 50V/0.1uF)
1
EA
....6 C629 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C631 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C704 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C705 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C718 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C719 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C722 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
Harman Kardon
AVR 165/230V Service Manual
Page 19 of 111

AVR165/230 INPUT PCB ASS'Y
Level Ref# Component Description Drawing No REQ-Qty UM
....6 C737 CCSNA0J220B CAP , CHIP TANTAL(22uF/6.3V, NingXia XingRi) XRCA45 XXX M XXX AT 1EA
....6 C738 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C745 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C746 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C747 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C748 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C754 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C756 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C758 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C759 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C760 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C761 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C762 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6
C763
CCUS1H104KC
CAP, CHIP(1608, 50V/0.1uF)
1
EA
....6
C763
CCUS1H104KC
CAP, CHIP(1608, 50V/0.1uF)
1
EA
....6 C767 CCUS1A105KC CAP, CHIP(1608, 10V/1uF) 1EA
....6 C773 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 C780 CCUS1H102KC CAP, CHIP(1608, 50V/1000pF) 1EA
....6 C781 CCUS1H223KC CAP, CHIP(1608, 50V/0.022uF) 1EA
....6 C820 CCUS1H104KC CAP, CHIP(1608, 50V/0.1uF) 1EA
....6 D725 CVD1SS355T DIODE, SMD, SWITCHING 1SS355/SOD-323 1EA
....6 L704 CLZ9R005Z FERRITE CHIP BEAD(1608/60ohm) HCB1608KF-600T30/COILMASTER 1EA
....6 R115 CRJ10DJ472T RES, CHIP(1608/5%/4.7Kohm) 1EA
....6 R116 CRJ10DJ472T RES, CHIP(1608/5%/4.7Kohm) 1EA
....6 R157 CRJ10DJ103T RES, CHIP(1608/5%/10Kohm) 1EA
....6 R163 CRJ10DJ104T RES, CHIP(1608/5%/100Kohm) 1EA
....6 R165 CRJ10DJ104T RES, CHIP(1608/5%/100Kohm) 1EA
....6 R171 CRJ10DJ0R0T RES, CHIP(1608/5%/0ohm) 1EA
....6 R217 CRJ10DJ101T RES, CHIP(1608/5%/100ohm) 1EA
....6
R218
CRJ10DJ101T
RES, CHIP(1608/5%/100ohm)
1
EA
....6
R218
CRJ10DJ101T
RES, CHIP(1608/5%/100ohm)
1
EA
....6 R219 CRJ10DJ101T RES, CHIP(1608/5%/100ohm) 1EA
....6 R245 CRJ10DJ104T RES, CHIP(1608/5%/100Kohm) 1EA
....6 R246 CRJ10DJ104T RES, CHIP(1608/5%/100Kohm) 1EA
....6 R289 CRJ10DJ104T RES, CHIP(1608/5%/100Kohm) 1EA
....6 R290 CRJ10DJ104T RES, CHIP(1608/5%/100Kohm) 1EA
....6 R291 CRJ10DJ563T RES, CHIP(1608/5%/56Kohm) 1EA
....6 R292 CRJ10DJ563T RES, CHIP(1608/5%/56Kohm) 1EA
....6 R293 CRJ10DJ563T RES, CHIP(1608/5%/56Kohm) 1EA
....6 R294 CRJ10DJ563T RES, CHIP(1608/5%/56Kohm) 1EA
....6 R317 CRJ10DJ561T RES, CHIP(1608/5%/560ohm) 1EA
....6 R320 CRJ10DJ682T RES, CHIP(1608/5%/6.8Kohm) 1EA
....6 R321 CRJ10DJ682T RES, CHIP(1608/5%/6.8Kohm) 1EA
....6 R322 CRJ10DJ103T RES, CHIP(1608/5%/10Kohm) 1EA
....6 R323 CRJ10DJ682T RES, CHIP(1608/5%/6.8Kohm) 1EA
....6
R324
CRJ10DJ682T
RES, CHIP(1608/5%/6.8Kohm)
1
EA
....6
R324
CRJ10DJ682T
RES, CHIP(1608/5%/6.8Kohm)
1
EA
....6 R325 CRJ10DJ682T RES, CHIP(1608/5%/6.8Kohm) 1EA
....6 R339 CRJ10DJ104T RES, CHIP(1608/5%/100Kohm) 1EA
....6 R341 CRJ10DJ104T RES, CHIP(1608/5%/100Kohm) 1EA
....6 R380 CRJ10DJ104T RES, CHIP(1608/5%/100Kohm) 1EA
....6 R381 CRJ10DJ561T RES, CHIP(1608/5%/560ohm) 1EA
....6 R382 CRJ10DJ561T RES, CHIP(1608/5%/560ohm) 1EA
....6 R383 CRJ10DJ561T RES, CHIP(1608/5%/560ohm) 1EA
....6 R384 CRJ10DJ561T RES, CHIP(1608/5%/560ohm) 1EA
....6 R389 CRJ10DJ563T RES, CHIP(1608/5%/56Kohm) 1EA
....6 R390 CRJ10DJ563T RES, CHIP(1608/5%/56Kohm) 1EA
....6 R399 CRJ10DJ104T RES, CHIP(1608/5%/100Kohm) 1EA
....6 R400 CRJ10DJ104T RES, CHIP(1608/5%/100Kohm) 1EA
....6 R401 CRJ10DJ104T RES, CHIP(1608/5%/100Kohm) 1EA
....6 R424 CRJ10DJ472T RES, CHIP(1608/5%/4.7Kohm) 1EA
....6 R425 CRJ10DJ392T RES, CHIP(1608/5%/3.9Kohm) 1EA
....6 R700 CRJ10DJ103T RES, CHIP(1608/5%/10Kohm) 1EA
....6 R717 CRJ10DJ0R0T RES, CHIP(1608/5%/0ohm) 1EA
....6 R718 CRJ10DF1371T RES, CHIP(1608/1%/1.37Kohm) 1EA
....6 R719 CRJ10DJ0R0T RES, CHIP(1608/5%/0ohm) 1EA
....6 R720 CRJ10DJ0R0T RES, CHIP(1608/5%/0ohm) 1EA
....6 R725 CRJ10DJ0R0T RES, CHIP(1608/5%/0ohm) 1EA
....6 R727 CRJ10DJ0R0T RES, CHIP(1608/5%/0ohm) 1EA
....6 R735 CRJ10DJ103T RES, CHIP(1608/5%/10Kohm) 1EA
....6 R745 CRJ10DJ103T RES, CHIP(1608/5%/10Kohm) 1EA
....6 R753 CRJ10DJ332T RES, CHIP(1608/5%/3.3Kohm) 1EA
....6 R754 CRJ10DJ332T RES, CHIP(1608/5%/3.3Kohm) 1EA
....6 R761 CRJ10DJ102T RES, CHIP(1608/5%/1Kohm) 1EA
....6 R762 CRJ10DJ102T RES, CHIP(1608/5%/1Kohm) 1EA
....6 R767 CRJ10DF5101T RES, CHIP(1608/1%/5.1Kohm) 1608 SIZE 1EA
....6 R779 CRJ10DJ103T RES, CHIP(1608/5%/10Kohm) 1EA
....6
R780
CRJ10DJ103T
RES, CHIP(1608/5%/10Kohm)
1
EA
....6
R780
CRJ10DJ103T
RES, CHIP(1608/5%/10Kohm)
1
EA
....6 R781 CRJ10DJ103T RES, CHIP(1608/5%/10Kohm) 1EA
....6 R812 CRJ10DJ103T RES, CHIP(1608/5%/10Kohm) 1EA
....6 R910 CRJ10DJ105T RES, CHIP(1608/5%/1Mohm) 1EA
....6 R963 CRJ10DJ105T RES, CHIP(1608/5%/1Mohm) 1EA
....6 C111 CCUI1C104KC CAP , CHIP (1005, 16V/0.1uF) 1EA
....6 C113 CCUS1H180JA CAP, CHIP(1608, 50V/18pF) 1EA
....6 C114 CCUS1H180JA CAP, CHIP(1608, 50V/18pF) 1EA
Harman Kardon
AVR 165/230V Service Manual
Page 20 of 111