Harrod VOL-050 User manual

Code:
Product:
INS691
Revision 9
24/10/17
Harrod UK Limited©
View of Product
MATCHPLAY VOLLEYBALL
VOL-050
Pack Contents:
1. 1 x Matchplay VBL Winder Post (FEQ971)
2. 1 x Matchplay VBL Base including fittings (FEQ976)
3. 1 x Matchplay VBL Dummy Post (FEQ970)
4a. 2 x Brace (PEQ973)
4b. 1x Straps
(pair)
(packed with FEQ970/971)
(packed with FEQ971) (FPK971)
Fittings Pack (packed within base)
5. 2 x M10 Nylock Nut (BOL202)
6. 6 x M10 Unistrut Nut (BOL204)
7. 8 x M10x20 Set Screw (BOL342)
8. 2 x M10x40 Hex Bolt (BOL322)
9. 2 x Base Back Plate (PEQ976)
10. 4 x ‘T’- Bolt (PEQ977)
1
4a
3
2
MAKE SURE YOU READ THESE
INSTRUCTIONS CAREFULLY BEFORE
ASSEMBLING YOUR POSTS
Floor Socket Installation:
All sockets should be installed by a specialist, using the
following guidelines. Please contact your distributor for
recommended specialist fitting engineers.
Mark at location shown in FIG.1. Drill Ø20 holes to the
depth to suit purchased sockets. Socket centres are 11m
x 0.4m (NOTE: 11m is the Harrod suggested centres, this
can range between 10.98m and 11.98m to meet ther
regulation distance between upright and sideline).
Note: Longer sockets are required for sprung floors
(contact your distributor for guidance).
0.5 to 1m 9m OUTER SIDELINES OF COURT
11m SOCKET CENTRES (see note above) FIG.1
FPK970
Floor sockets are not included and should be ordered
separately.
Solid Floors require 4 off SHP-001
Suspended Floors require 4 off SHP-100
Net Not Included
0.5 to 1m
0.4m
Socket Installation Dimensions - Plan View
490mm
11m CENTRES (this will position the front of the upright 510mm to the sideline)
(This dimension is suggested for guidance, see note above)

Assembly Instructions
1. Attach the uprights to the bases.
The easiest way to assemble the upright
to the base is to insert the bolts
through the front plate and screw into base
plate (9), and also insert the bolts through
the back plate and screw into the unistrut
nuts (see fig.2). Note: Screw the bolts in
only enough to hold as there needs to be
room left between the plates for the upright.
Slide the upright onto the base
plate/unistrut nuts so that they slot into the
front and back parts of the upright extrusion.
At this point tighten up all bolts to secure
the upright in place.
2. Attach the brace to the upright and base. To ensure
aesthetically pleasing, position the hole on the
underside of the brace, at the top, facing the back out
of view.
Insert the setscrew (8) through the brace (4a) and
screw only a few turns onto the unistrut nut (6). Insert
the unistrut nut into the top of the upright (as shown in
Fig 3) and slide down the upright. Position the other
end of the brace onto the welded bolt on the back of
the base and secure with an M10 Nylock nut (5). Now
fully tighten the top end of the brace onto the upright
(the end of the bolt will poke through the hole in the
upright to stop any chance of the brace slipping in
use.
(1&3) (2) (7)
(6)
3. Fit the net
Attach the headline wire to the carbine clip and strap.
Tension the net to the required height by moving the
lever in the direction shown in FIG.4.
Locate the end of the strap in the slot and lift the
winch lever three or four times until it grips.
FIG.4
To release the tension on the strap, move the lever in
the direction of the arrow, whilst at the same time
pulling the release button on the underside of the
winch.
FIG.2
4a
10
9
6
7
FIG.3
8
6
Code:
Product:
INS691
Revision 9
24/10/17
Harrod UK Limited©
MATCHPLAY VOLLEYBALL
VOL-050