Harrod FBL-580 User manual

FBL-580/583/586/588/581/584/587/589/592/593
780/783/786/788/781/784/787/789/792/793
3G Folding Projection Goal
INS597
Revision 8
06/04/2018
Harrod UK Limited©
Code:
Product:
Pack Contents
Item number:
Product Size Projection
FBL-580 4.88x1.22m 2.3 to 3.5m 1 FEP318 2 FEP299 4 FBL-291 2 FEQ331 1 FEP311 2 FEP320 2 FEP697 2 FEP698 1 FEP699 1 FPK313
FBL-583 4.88x1.22m 3.5 to 5m 1 FEP318 2 FEP299 4 FBL-291 2 FEQ331 1 FEP311 2 FEP316 2 FEP708 2 FEP709 1 FEP699 1 FPK313
FBL-586 4.88x1.83m 2.3 to 3.5m 1 FEP318 2 FEP300 4 FBL-291 2 FEQ331 1 FEP311 2 FEP320 2 FEP694 2 FEP695 1 FEP696 1 FPK313
FBL-588 4.88x1.83m 3.5 to 5m 1 FEP318 2 FEP300 4 FBL-291 2 FEQ331 1 FEP311 2 FEP316 2 FEP706 2 FEP707 1 FEP696 1 FPK313
FBL-581 3.66x1.22m 2.3 to 3.5m 1 FEP317 2 FEP299 4 FBL-291 2 FEQ331 1 FEP311 2 FEP320 2 FEP697 2 FEP698 1 FEP699 1 FPK313
FBL-584 3.66x1.22m 3.5 to 5m 1 FEP317 2 FEP299 4 FBL-291 2 FEQ331 1 FEP311 2 FEP316 2 FEP708 2 FEP709 1 FEP699 1 FPK313
FBL-587 3.66x1.83m 2.3 to 3.5m 1 FEP317 2 FEP300 4 FBL-291 2 FEQ331 1 FEP311 2 FEP320 2 FEP694 2 FEP695 1 FEP696 1 FPK313
FBL-589 3.66x1.83m 3.5 to 5m 1 FEP317 2 FEP300 4 FBL-291 2 FEQ331 1 FEP311 2 FEP316 2 FEP706 2 FEP707 1 FEP696 1 FPK313
FBL-592 4.88x2.13 2.3 to 3.5m 1 FEP318 2 FEQ117 4 FBL-291 2 FEQ331 1 FEP311 2 FEP320 2 FEP694 2 FEP695 1 FEQ575 1 FPK313
FBL-593 4.88x2.13 3.5 to 5m 1 FEP318 2 FEQ117 4 FBL-291 2 FEQ331 1 FEP311 2 FEP316 2 FEP706 2 FEP707 1 FEQ575 1 FPK313
Item number:
Product Size Projection
FBL-780 4.88x1.22m 2.5 to 3.7m 1 FEP318 2 FEP299 4 FBL-291 2 FEQ331 1 FEP141 2 FEP320 2 FEP697 2 FEP698 1 FEP699 1 FPK313
FBL-783 4.88x1.22m 3.7 to 5.2m 1 FEP318 2 FEP299 4 FBL-291 2 FEQ331 1 FEP141 2 FEP316 2 FEP708 2 FEP709 1 FEP699 1 FPK313
FBL-786 4.88x1.83m 2.5 to 3.7m 1 FEP318 2 FEP300 4 FBL-291 2 FEQ331 1 FEP141 2 FEP320 2 FEP694 2 FEP695 1 FEP696 1 FPK313
FBL-788 4.88x1.83m 3.7 to 5.2m 1 FEP318 2 FEP300 4 FBL-291 2 FEQ331 1 FEP141 2 FEP316 2 FEP706 2 FEP707 1 FEP696 1 FPK313
FBL-781 3.66x1.22m 2.5 to 3.7m 1 FEP317 2 FEP299 4 FBL-291 2 FEQ331 1 FEP141 2 FEP320 2 FEP697 2 FEP698 1 FEP699 1 FPK313
FBL-784 3.66x1.22m 3.7 to 5.2m 1 FEP317 2 FEP299 4 FBL-291 2 FEQ331 1 FEP141 2 FEP316 2 FEP708 2 FEP709 1 FEP699 1 FPK313
FBL-787 3.66x1.83m 2.5 to 3.7m 1 FEP317 2 FEP300 4 FBL-291 2 FEQ331 1 FEP141 2 FEP320 2 FEP694 2 FEP695 1 FEP696 1 FPK313
FBL-789 3.66x1.83m 3.7 to 5.2m 1 FEP317 2 FEP300 4 FBL-291 2 FEQ331 1 FEP141 2 FEP316 2 FEP706 2 FEP707 1 FEP696 1 FPK313
FBL-792 4.88x2.13m 2.5 to 3.7m 1 FEP318 2 FEQ117 4 FBL-291 2 FEQ331 1 FEP141 2 FEP320 2 FEP694 2 FEP695 1 FEQ575 1 FPK313
FBL-793 4.88x2.13m 3.7 to 5.2m 1 FEP318 2 FEQ117 4 FBL-291 2 FEQ331 1 FEP141 2 FEP316 2 FEP706 2 FEP707 1 FEQ575 1 FPK313
L/H
Bottom
Sidebar Fittings
Folding
Goal Net
Support
R/H
Bottom
Sidebar
Internal
AdjusterCrossbar Upright Socket
Support
Post
Thro
Fence
Arm
Internal
Adjuster
L/H
Bottom
Sidebar
R/H
Bottom
Sidebar
Folding
Goal Net
Support FittingsCrossbar Upright Socket
Support
Post
Support
Post
Hinge
IMPORTANT Please read through the
instructions before assembling your goals.
AT LEAST 3 PEOPLE ARE REQUIRED
TO ASSEMBLE THIS PRODUCT.
Socket Location: Behind Fence
Socket Location: In Front of Fence
5 842 10 7 93 61
5 842 10 7 93 61
View of Product
3
9
8
7
6
5
4
1
2
Sockets behind the
fence/kickboard
Sockets in front of the
fence/kickboard
5
6
4

SMALLPARTS FITTINGS PACK (FPK313)
10) 12 x M12 NYLOC NUT (BOL102)
11) 4 x M12 BOLT 110mm (BOL110)
12) 8 x M12 BOLT 100mm (BOL122)
13) 48 x M10 NYLOC NUT (BOL202)
14) M10 FLAT WASHER FORM B S/S (BOL711)
15) 8 x M10 x 75 C/S SOCKET SCREW (BOL288)
16) 4 x M10 SET SCREW 50mm (BOL306)
17) 24 x M10 SQUARE HEAD BOLT 25mm (BOL336)
18) 4 x LARGE WASHER (BOL702)
19) 40 x M10 PLAIN WASHER (BOL709)
3G Folding Projection Goal
Code:
Product:
This product is protected by © Copyright
and Design Right Harrod UK Ltd 2006
Fittings Pack
20) 36 x M12 NYLON WASHER (BOL724)
21) 2 x 0.5m CHAIN (BOL818)
22) 2 x NET ROPE (FBL-015)
23) 1 x “S” TYPE NET CLIPS (FPK012)
24) 4 x BOTTOM HINGE BRACKET (PEP193)
25) 4 x U-Bar M10 104X122.5mm ID (SEP497)
26) 2 x L/H TOP HINGE BRACKET (PEQ187)
27) 2 x R/H TOP HINGE BRACKET (PEQ188)
28) 2 x CARABINER CLIP (HKS008)
29) 1 x NET HOOKS (Supplied with Crossbar) (HKS029)
(Pack)
(pack)
10 11 12 13 14 15 16 17 18 19 20
21
23
24 25 26 27 28 29
Install Sockets
Fig.2a
1Dig holes 600x600 square x m deep at centres shown in Fig 2a.
Position the sockets (3) 360mm centrally back from the front (court
side) of the fence/kick board. Concrete the sockets in leaving approx
40mm from top of concrete to ground level (for turf). Use a spirit level to
make sure that the sockets are truly vertical and support until set. Replace the
turf extracted when the concrete has cured (allow the concrete to set before
rest of the goal).
600 m
assembling the
3
4956mm CRS for 4.88m Crossbar
3736mm CRS for 3.66m Crossbar
PLAN VIEW
SIDE VIEW
Fence Line
600
600
600
360 Socket
centre to
front of fence/
kick board
40
Play Area
Fig.2b
100mm Socket
centre to
front of fence/
kick board
3
SIDE VIEW
600
600 40
PLAN VIEW
Fence Line
600 Play Area
Important: Please ensure you match the part number of your goal to the
installation figures (2a or 2b) below.
1Dig holes 600x600 square x m deep at centres shown in Fig 2b.
Position the sockets (3) 100mm centrally forward from the front (court
side) of the fence/kick board. Concrete the sockets in leaving approx
40mm from top of concrete to ground level (for turf). Use a spirit level to
make sure that the sockets are truly vertical and support until set. Replace the
turf extracted when the concrete has cured (allow the concrete to set before
rest of the goal).
600 m
assembling the
Socket Location: Behind Fence
FBL-580, FBL-583, FBL-586, FBL-588, FBL-581, FBL-584,
FBL-587, FBL-589, FBL-592, FBL-593
4956mm CRS for 4.88m Crossbar
3736mm CRS for 3.66m Crossbar
Socket Location: In Front of Fence
FBL-780, FBL-783, FBL-786, FBL-788, FBL-781, FBL-784,
FBL-787, FBL-789, FBL-792, FBL-793
FBL-580/583/586/588/581/584/587/589/592/593
780/783/786/788/781/784/787/789/792/793

3G Folding Projection Goal
This product is protected by © Copyright
and Design Right Harrod UK Ltd 2006
Code:
Product:
413
18
16
678
12
10
20
14
16 18
Fig.10
Fig.3
Roller Wheel
Fig.4
Assembly Instructions
Cut hole in fence and assemble Support Posts (Behind Fence Sockets Only) -
directly in front for each socket measure up from ground level 145mm to square centre
and cut a square hole 90x90mm in the fence (or kick board).
5Fix the Sidebars to the Uprights - Fit each assembled
Sidebar (from Step 3) to the Thro-fence Support Arm (as
Shown in Fig 3). With at least 2 people, lift the Goal Frame
(from step 4) and fit to the Sidebars at the bottom (as shown in
Fig 6). Depending on your surface, you can adjust the gap under
the upright by moving the Bottom Bracket (24), up or down.
6Fit Net Support - Fit each Net Support (9) to the Uprights
as shown in Fig 6 then fit to the Sidebars as shown in Fig 7
ensuring that the countersunk head of the Bolt (15) fits into
the dimple on the Net Support.
4Assemble the Crossbar to the Uprights - Lay the Crossbar (1) and Uprights (2)
flat on the ground and insert 4 Square Headed Bolts (17) into each Crossbar and
Upright. Slide the Uprights onto the crossbar ensuring that the net hook slot is
facing upwards. Secure the Crossbar using the Brackets (26 & 27) and Bolts also fit the
Bottom Brackets (24) with bolts as shown in Fig 5.
8Fitting The Net (Not Supplied) -Attach the net hooks (29) to the net approx 250mm apart, then
insert the hook into the slot on the goal section and twist to lock. As a guide you should fit 8 to
each Upright and the remainder to the Crossbar. Tie the headline Rope (supplied with the net) to
the Net Support and the Net Rope (22) to the Lugs on the Sidebars, weaving the rope through the net
to stop the ball going underneath. Finally loop the net runback under the Sidebars and fix the net back
onto itself with “S” type Net Clips (23).
9Folding The Goal - The goal can be folded in either
direction about the Support Posts. With 2 people, push
each upright simultaneously in the chosen direction until
they become into position.
When the goal is in the folded position (as shown in Fig 10), fix
the goal to the fence with the Chain (21) and Carabiner Clip (28)
provided. To prevent unauthorized use of the goal you should
replace the Carabiner Clip with a Padlock (not supplied).
3Assemble Sidebars - Remove any unnecessary bolts and insert an internal
adjuster (6) into each of the Sidebars (7 & 8). Lining up the desired bolt hole with
the slot in the Sidebar. Fasten with Bolt (16) and Large Washer (18) (as shown in
fig 4). Don’t worry at this stage about the exact projection of the goal, any adjustment
can be made later. Fit the sidebars to the Thro-fence arms with the slot facing inwards.
GL
Fig.6
5
20
20
13
19
Fig.5
55
2627
1319
1
2
17
24
20
13
12
9
20
13
11
87
Fig.7
21
15
Thro-fence
Support Arm
Fig.9
28
7Adjusting the Projection - To achieve accurate
projection, adjust Bolt (16) as shown in Fig 8, so that the
uprights sit over the Goal Line.
Fig.8
70
145
19
2Insert the Support Posts (4) into the Sockets and fix the Support Arms/Support
Post Hinge (5) to the Posts using M10 Nuts (12) and U-Bolt (14), positioning the
Arms so that theArm Plate is 70mm from Ground Level (as shown in Fig 3).
Folding The Goal
FBL-580/583/586/588/581/584/587/589/592/593
780/783/786/788/781/784/787/789/792/793