Harrod HAN-010 User manual

INS385
Revision 1
06/06/11
Harrod UK Limited©
Pack Contents
View of Product
1. 2 x Crossbars (FEP393)
2. 2 x Uprights (pair) (FEP395)
3. 2 x Sideframes (pair) (FEP365)
4. 1 x Backbars (pair) (FEP419)
Fittings Pack (FPK396)(packed with Backbars)
5. 20 x M10 x 25mm STST Square Bolt (BOL336)
6. 20 x M10 Form C STST Washer (BOL709)
10. 12 x 135mm Elastic Loop with Hook (ROP230)
7. 20 x M10 BZP Nylock Nut (BOL202)
8. 4 x M12 x 70mm Handwheel (BOL134)
9. 1 x Net Hook (60 Pack) (FPK366)
Page 1
WARNING
IMPORTANT
Any goal either in-use or otherwise must
be secured against overturning .
Please read the assembly instructions
carefully before starting to assemble your
goal.
Specialist Socket Installation
2 People to Assemble Goal
at all times
Requirements
Tools
1 x 17mm Spanner
6
7
5
9
10
4
1
2
3
8
Contents of Fitting Pack - FPK396
Net & Floor Sockets:-
Nets and floor sockets are supplied separately. To purchase a
these, please contact our Sales office who will be able to provide
you with a suitable distributor - Please quote the following part
numbers: Net HAN-005, Floor Sockets SHP-001/SHP-100.
HAN-010
Aluminium Competition Handball Posts
Code:
Product:

This product has been designed and tested
to meet the requirements of EN 749:2004
Floor Socket Installation -All sockets should be installed by a specialist, using the following
guidelines.
Drill 20mm diameter holes at the locations shown in Fig 1 to a depth to suit the purchased
sockets. Insert the socket and tighten to secure. (longer sockets are required for Sprung floors)
Please contact your distributor for recommended specialist fitting engineers.
Page 2
1Goal Frame - Insert Square Headed Bolts into the Crossbar and
Uprights as shown in Fig 2 and slide frame together.
HAN-010
Aluminium Competition Handball Posts
Code:
Product:
Fig 1
Socket Position
Outer Goal Line
Goal Line
Direction towards
the playing area
Assembly Instructions
Uprights
Socket
Positions
Note: Floor Sockets are sold separately - see note on page 1.
3198 CENTRES
3000
420
2 x 20 HolesØ
99
5
5
5
5
x2 x2
Fig 2
1
2

This product is protected by © Copyright
and Design Right Harrod UK Ltd 2010.
Page 3
Fig 3
HAN-010
Aluminium Competition Handball Posts
Code:
Product:
Push Button
clip in & insert
into collar.
7
6
7
6
3
Fig 4
3Fit The Backbar - Stand the goal up and fit the
Backbar as shown in Fig 4 by depressing the
button clips.
2Attach the Sideframes - Position each Sideframe as shown in
Fig 3 and secure with Washers and Nuts.
Pull plunger
to fold.

This product is protected by © Copyright
and Design Right Harrod UK Ltd 2010.
Page 4
Fig 5
HAN-010
Aluminium Competition Handball Posts
Code:
Product:
Folding The Sideframe
Fitting the Net (sold separately) - Locate the Crossbar edge of the Net (identified with a label). Attach the Net Hooks to the
Crossbar and Upright edges then insert & lock the Hooks into the recess. Fit the Net Hooks to the Red areas on the Goal (The
hooks may damage the white bands when twisted)
Slot the edge of the net into the cut-outs in the top and bottom hinge bracket.
Ensure that the net is situated within the Sideframe then fit an
Elastic with Loop to each corner of the Net by threading it back
onto itself (Refer to Fig.7). Fix to the lugs on the Sideframe and
place another Elastic Loop at
the position of the Curtain Net
(fitted to Competition Net
HAN-005).
A minimum of 2 People are required to safely fold and move this Goal
To fold the Sideframe, first remove the backbar by depressing the button clip then slide the backbar out (see Step 3). Then pull
the plunger knob down to un-lock the Sideframe (see Step 2). Fold the Sideframe and release the plunger to lock.
This goal must be secured against overturning
at all times
Anchoring the Goal
(even when not in use)
- Secure the goal by
inserting the Handwheels supplied through the
hole in the Sideframe and screwing into the floor
socket, see Fig 5.
The handwheel has a nut pre-fitted; in normal
circumstances this can be left in place. Where the
thread in the ground socket is lower than ground
level, remove this nut to provide more thread to
screw into the floor socket.
Anchoring The Goal
Fitting The Net
Fig 6 Fig 7
Remove Nut, if
required.