HARVEY RG-1 User manual

Universal Roller Guide
Model: RG-1 RG-2
Revision A 2022-03-07
298007001

Contents
1.Foreword..................................................................................................1
2.Warranty Information........................................................................... 1
3.Application.............................................................................................. 1
4.General Instructions.............................................................................2
5.Specifications.........................................................................................2
6.Feature Identification........................................................................... 2
7.Operations............................................................................................... 3
8.Maintenance............................................................................................4
1.前言............................................................................................................ 6
2.质保信息.................................................................................................... 6
3.适用范围.................................................................................................... 6
4.注意事项.................................................................................................... 7
5.参数信息.................................................................................................... 7
6.组成部分.................................................................................................... 7
7.操作说明.................................................................................................... 8
8.日常维护.................................................................................................... 8
Exploded View and Parts List............................................................... 9

English Version

1
1. Foreword
This manual includes basic information for the safe assembly, operations
and maintenance of the RG-1&2 Universal Roller Guide. This manual
assumes that the operator (user) is qualified to perform the tasks specified
herein and is qualified to operate the product with the intended machines
safely. This document does not address safety procedures for any
unintended use of this tool. The operator must carefully read and
understand the contents of this manual before using the tool. Improper
installation, assembly or operation of this tool may negate the safety feature
designs of the tool. Please retain this manual for future reference.
2. Warranty Information
Limited Tool Warranty:
We make every effort to ensure that this product meets the highest quality
and durability standards. We warrant that this product is free from
manufacturing defects for two years under the terms of a limited warranty.
The two-year term begins at the time of the retail purchase. This warranty
does not apply to defects due directly or indirectly to misuse, abuse, normal
wear and tear, negligence or accidents, repairs done by an unauthorized
service center, alterations or lack of maintenance. We shall in no event, be
liable for death, injuries to persons or property or for incidental, special or
consequential damages arising from the use of our products. To take
advantage of this limited warranty, please reach out to our Harvey’s
customer service center. After examination, we will repair or replace the
product or any part(s) covered under this warranty due to defective
workmanship or material(s) during this warranty period.
3. Application
The Universal Roller Guide is used to assist in holding the workpiece during
cutting.
It is intended to be used in conjunction with a table saw, bandsaw, sander
or shaper which is equipped with the T-slot (Width of top and bottom: 3/4”
and 1”; Depth: 3/8”).
The workpiece can be locked effectively even with slightly uneven edges.

2
4. General Instructions
4.1 The product is designed with roller pressure of 70N-100N and shall not
be used in scenarios higher than 100N.
4.2 The product is an accessorial tool. When used in conjunction with
another machines, all relevant operation requirements and safe
practices must be followed.
4.3 After usage, please properly store away in a clean and safe area.
4.4 Note that the rotation direction of the roller should be consistent with the
direction of wood feeding.
5. Specifications
6. Feature Identification
Fig.1
Model
RG-1
RG-2
Main Body Thickness
1” (25.4 mm)
2” (50.8mm)
Recommended Stock
Thickness
Min: 1/16” (2 mm)
Max: 2” (51 mm)
Min: 1/16” (2 mm)
Max: 4” (102 mm)
Roller Travel
6-1/2” (165 mm)
Roller Diameter
2” (50.8 mm)
Compatible T-slot Size
3/4" x 3/8" x 1" (19.05 x 25.4 x 9.525 mm)
Roller Pressure
70N～100N
Overall Size
8-3/4" x 7" x 2-41/64"
(222 x 175 x 67 mm)
8-3/4" x 7" x 3-5/8"
(222 x 175 x 92 mm)
Weight
4.2 lbs (1.9 kg)
5.5 lbs (2.5 kg)
No.
Name
A
T-block
B
Locking Knobs
C
Adjusting Knob
D
One-way Rollers

3
7. Operations
Fig.2
The following application is intended for the use on the table saw (as shown in
Fig.2), which can be taken as a reference for the operations on other machines:
1. Align and lock the table saw fence (as intended to setup a cut);
2. Rest the workpiece against the fence (as seen in Fig.2);
3. Loosen the locking knobs (B) and insert the T-block (A) into the T-slot;
4. While locking knobs are loosened, turn the adjusting knob (C) to the zero “0”
position;
5. Push the roller guide towards the workpiece until the two rollers (D) touch
the workpiece, while the other side of workpiece firmly pushed against the
fence;
6. Lock the roller guide on the table by tightening the locking knobs (B);
7. Turn the adjusting knob (C) to apply pressure to the workpiece. Rotating the
adjustment knob in either direction (clockwise or counter-clockwise) will
work;
8. Gently push on the workpiece to ensure that it is firmly secured between the
table saw fence and the Universal Roller Guide, if not, continue to adjust until
the pressure is appropriate.
IMPORTANT NOTE: Before installing the Universal Roller Guide, please
ensure that the feed direction indicated by the arrow on the roller guide is

4
consistent with the feed direction of the workpiece, otherwise, the roller
guide needs to be turned over and re-installed.
8. Maintenance
8.1 Check the roller regularly for normal rotation.
8.2 To ensure proper functionality, please clean any debris or dust buildup
that may accumulate on the tool over time.

中文版本

6
1.前言
本说明书与产品一起交付给客户。说明书包含对操作人员的要求、产品
的适用环境以及正确安全的使用方法，但不包含全部的安全要求。在使用之
前，操作人员必须仔细阅读并理解本说明书，才能有效的避免错误的安装和
操作，保证人身安全。
2. 质保信息
质保期限
两年
购买凭证
请保留有效的购买凭证，以作保修及维修之用。
质保范围
自客户购买本产品之日起，本公司将向客户提供为期两年的质保服务，
在质保期内，产品因质量缺陷免费维修。
以下原因造成的事故、故障等在保修范围以外：
◆ 滥用、误用、疏忽引起的事故。
◆ 缺乏维护导致的故障。
◆ 非授权维修改造。
◆ 正常磨损部件。
◆ 天灾、火灾、爆炸引起的故障。
本公司在任何情况下均不对因使用本公司产品而导致的死亡、人身伤害
和财产损失负责。
任何部件经过检测确认出现工艺或材质的缺陷，我们将免费进行修理或
者更换。`
3. 适用范围
该产品用于切割木料时辅助压紧。
该产品适用于台锯，带锯、砂光机、铣床等台面配有T型槽（尺寸：顶部
3/4" ，底部1"，深度3/8"）的设备。
木料宽度有轻微偏差时仍可以有效压紧。

7
4. 注意事项
4.1 该产品设计压紧力为 70N-100N，不得在大于 100N 场景中使用。
4.2 该产品仅为辅助工具，在其它设备上使用时需按照设备操作规范及使用
要求进行。
4.3 使用完毕请有效锁紧在台面或放置至安全区域。
4.4 使用时注意滚轮旋转方向和木料进给方向一致。
5. 参数信息
6. 组成部分
图 1
型号
RG-1
RG-2
本体厚度
25.4mm
50.8mm
适用木料厚度
2-51mm
2-102mm
行程
165mm
滚轮直径
50.8mm
适用 T 型槽
19.05mm x 25.4mm x 9.525mm
压力范围
70N～100N
外形尺寸
222mm x 175mm x 67mm
222mm x 175mm x 92mm
重量
1.9kg
2.5kg
编号
名称
A
T 型块
B
锁紧把手
C
调节旋钮
D
单向滚轮

8
7. 操作说明
图 2
下面以台锯上的运用为例，介绍该产品的操作，其余运用，参照该说明进行
操作(如图 2 所示)：
1. 将直靠尺有效锁紧；
2. 将待加工木料放在台板上，一侧与直靠尺靠板接触；
3. 松开锁紧旋钮“B”,将 T 形块“A”插入 T 槽内；
4. 将调节旋钮旋“C”转至 0 档；
5. 移动压料器至两个单向滚轮“D”均接触木料，木料另一侧与靠板有效接
触；
6. 通过锁紧旋钮将压料器有效固定在台板上；
7. 旋转调节旋钮给木料施加压力（左右旋转均可）；
8. 轻微推动木料，如压力不适，继续调整，直至压力合适。
注意：
安装前需确认箭头指示方向与进料方向一致，否则需要将压料器翻转，重新
安装后使用。
8. 日常维护
8.1 定期检查滚轮是否正常转动。
8.2 及时清理附着在产品上的木屑。

9
Exploded View and Parts List

REF
DESCRIPTION
REF
DESCRIPTION
1-1
Flat HD screw M4-0.7x10
18
Set screw M6x30
1-2
Flat HD screw M4-0.7x18
19
Nut M6
2-1
Roller
20
Guide rod
2-2
Thickened roller
21
Copper sets 8x23x20
3-1
Spindle
22
Adjustment knob
3-2
Extended spindle
23
Bearing 6170 ZZ
4
Key 3x3x8
24
Pin Ø3.5x16
5
One-way bearing CSK10PP
25
Eccentric roller
6
Fixed block
26
upper substrate
7
Set screw M4-0.7x4
27
Pin
8
Pin Ø4X8
28-1
Fixed block
9
Lower substrate
28-2
Thickened fixed block
10
Spring
29
Cap screws
11
Spacer
30
Locking knob M4x10
12
Wire retaining ring Ø10
31
Gasket
13
Copper sets 6x10x25
32
T-block
14
Cylindrical nut M5x14xØ8
33-1
Flat HD screw M8x50
15
Slider
33-2
Flat HD screw M8x75
16
Bar
34-2
Flat HD screw M4-0.7x10
17
Shoulder screws M5xØ6x35
Remark：
-1 for parts of RG-1，-2 for parts of RG-2.
Eg: 1-1 Flat HD screw M4-0.7x10 is for RG-1
1-2 Flat HD screw M4-0.7x18 is for RG-2

Harvey Industries Co., Ltd.
68-10 Suyuan Avenue, Jiangning District, Nanjing 21100, China
www.harveymachinery.com
Harvey Industries International Inc.
10830 Ada Ave. Montclair, CA. 91763
TEL: [phone]
E-mail: [email protected]