Hasbro Playskool Play Favorites Step Start Walk 'n... User manual

DIAL:
With body/chassis on its side, insert dial into recess.
Turn body so that underside of chassis faces you.
Insert #6 screw with attached washer into hole, and
tighten with Phillips/cross head screwdriver.
4
SCREW DIAL
HOLE
ROLLER:
Turn body/chassis right side up and lower chassis
onto body. Insert posts on roller into holes in
recessed area (smaller post into smaller hole,
larger post into larger hole).
ROLLER
RECESSED AREA
5
INCLUDES: body/chassis, 4 wheels, front handle, rear handle, handle retainer, domed lid,
dial, roller, spinner (2 pieces), antenna, gear shift, 4 plain #6 screws, and 1 #6 screw with attached washer.
Adult assembly required.
Phillips/cross head screwdriver
(not included) needed for assembly.
Thank you for choosing this
PLAYSKOOL toy!
Step Start Walk ‘n RideTM
05545
9
months
OVER
ATTACH WHEELS:
Tip body/chassis on its side. Snap wheel onto axle,
with flat side of wheel against chassis. Repeat for
remaining 3 wheels.
ASSEMBLE HANDLES:
To snap front and rear handles together:
Place rear handle upside down on flat surface.
Holding front handle with back facing rear handle
and perpendicular to rear handle, snap posts on
front handle into holes in rear handle.
1
WHEEL
CHASSIS
2
FRONT HANDLE
REAR HANDLE
ATTACH HANDLE ASSEMBLY TO BODY:
Lift body and remove cardboard insert.
Turn body/chassis on its side. Insert front handle
through slot in body.
Fit axle on rear handle into ridges in underside of body.
Place handle retainer over axle (retainer fits only one way).
Using the 4 plain #6 screws and Phillips/cross head screwdriver
(not included), attach retainer to body.
NOTE: If body is locked closed, see page 7 for conversion
instructions.
3
BODY
CARDBOARD INSERT
FRONT HANDLE
SLOT
RIDGES
AXLE
SCREWS HANDLE RETAINER
Product must be assembled by an adult. This product contains
small parts which are necessary for assembly. Prior to and
during of this product, keep small parts out of children’s reach.
Small parts pose a choke hazard to children under 3 years.
TO AVOID SERIOUS INJURY: Continuous adult supervision
required;
never use near motor vehicles, near streets,
swimming pools,
hills, steps, or sloped driveways. Always
wear shoes. Allow only one rider.
MAXIMUM WEIGHT 42 LBS. (19 KGS.)
05545942B_PLA_WalknRide_INST_FAR OP.indd 2-3 30/01/2012 3:24 PM

DIAL:
With body/chassis on its side, insert dial into recess.
Turn body so that underside of chassis faces you.
Insert #6 screw with attached washer into hole, and
tighten with Phillips/cross head screwdriver.
4
SCREW DIAL
HOLE
ROLLER:
Turn body/chassis right side up and lower chassis
onto body. Insert posts on roller into holes in
recessed area (smaller post into smaller hole,
larger post into larger hole).
ROLLER
RECESSED AREA
5
INCLUDES: body/chassis, 4 wheels, front handle, rear handle, handle retainer, domed lid,
dial, roller, spinner (2 pieces), antenna, gear shift, 4 plain #6 screws, and 1 #6 screw with attached washer.
Adult assembly required.
Phillips/cross head screwdriver
(not included) needed for assembly.
Thank you for choosing this
PLAYSKOOL toy!
Step Start Walk ‘n RideTM
05545
9
months
OVER
ATTACH WHEELS:
Tip body/chassis on its side. Snap wheel onto axle,
with flat side of wheel against chassis. Repeat for
remaining 3 wheels.
ASSEMBLE HANDLES:
To snap front and rear handles together:
Place rear handle upside down on flat surface.
Holding front handle with back facing rear handle
and perpendicular to rear handle, snap posts on
front handle into holes in rear handle.
1
WHEEL
CHASSIS
2
FRONT HANDLE
REAR HANDLE
ATTACH HANDLE ASSEMBLY TO BODY:
Lift body and remove cardboard insert.
Turn body/chassis on its side. Insert front handle
through slot in body.
Fit axle on rear handle into ridges in underside of body.
Place handle retainer over axle (retainer fits only one way).
Using the 4 plain #6 screws and Phillips/cross head screwdriver
(not included), attach retainer to body.
NOTE: If body is locked closed, see page 7 for conversion
instructions.
3
BODY
CARDBOARD INSERT
FRONT HANDLE
SLOT
RIDGES
AXLE
SCREWS HANDLE RETAINER
Product must be assembled by an adult. This product contains
small parts which are necessary for assembly. Prior to and
during of this product, keep small parts out of children’s reach.
Small parts pose a choke hazard to children under 3 years.
TO AVOID SERIOUS INJURY: Continuous adult supervision
required;
never use near motor vehicles, near streets,
swimming pools,
hills, steps, or sloped driveways. Always
wear shoes. Allow only one rider.
MAXIMUM WEIGHT 42 LBS. (19 KGS.)
05545942B_PLA_WalknRide_INST_FAR OP.indd 2-3 30/01/2012 3:24 PM

6
ANTENNA:
Antenna fits only one way. Insert end of
antenna into hole.
ANTENNA
HOLE
DOMED LID:
Insert posts on domed lid into holes in
recessed area.
7
DOMED LID
RECESSED AREA
SPINNER PIECE
GEAR SHIFT:
Gear shift fits only one way. Inserts posts on gear
shift into holes in recessed area (smaller post into
smaller hole, larger post into larger hole).
8
GEAR SHIFT
RECESSED AREA
RECESSED AREA
SPINNER
SPINNER:
Slide slots on each spinner piece into each other
until they snap into place. Snap assembled
spinner into recessed area.
9
LATCH
TO CONVERT FROM RIDE-ON TO WALKER:
Lift toy to access underside of chassis. Squeeze latch with one hand, and at
same time, grasp rear handle and lift up body. Push handle down to lock
into place. Listen for click. Pull up on handle to confirm handle is locked.
CAUTION:
LATCH
Questions? Call 1-800-PLAYSKL
Visit
Visit
.com
Product and colors may vary.
© 2012 Hasbro. All Rights Reserved.
TM & ® denote U.S. Trademarks.
U.S. Pat. Nos. 6296268 and D424126.
05545 PN 7268760000
TO CONVERT FROM WALKER TO RIDE-ON:
Squeeze latch on top of chassis. Lift rear handle up and forward.
Rotate handles up then lower body onto chassis.
Make sure the handle locks into place.
CAUTION:
LATCH
PMS 186 Black PIGUET GRAPHIC 17-1-12 Hb T1-17-115 05545942B_PLA_WalknRide_INST_FAR.OP /EPSON 18Mac 06 175
05545942B PLA STEP START WALK N RIDE - US
05545942B_PLA_WalknRide_INST_FAR OP.indd 4-5 30/01/2012 3:24 PM

6
ANTENNA:
Antenna fits only one way. Insert end of
antenna into hole.
ANTENNA
HOLE
DOMED LID:
Insert posts on domed lid into holes in
recessed area.
7
DOMED LID
RECESSED AREA
SPINNER PIECE
GEAR SHIFT:
Gear shift fits only one way. Inserts posts on gear
shift into holes in recessed area (smaller post into
smaller hole, larger post into larger hole).
8
GEAR SHIFT
RECESSED AREA
RECESSED AREA
SPINNER
SPINNER:
Slide slots on each spinner piece into each other
until they snap into place. Snap assembled
spinner into recessed area.
9
LATCH
TO CONVERT FROM RIDE-ON TO WALKER:
Lift toy to access underside of chassis. Squeeze latch with one hand, and at
same time, grasp rear handle and lift up body. Push handle down to lock
into place. Listen for click. Pull up on handle to confirm handle is locked.
CAUTION:
LATCH
Questions? Call 1-800-PLAYSKL
Visit
Visit
.com
Product and colors may vary.
© 2012 Hasbro. All Rights Reserved.
TM & ® denote U.S. Trademarks.
U.S. Pat. Nos. 6296268 and D424126.
05545 PN 7268760000
TO CONVERT FROM WALKER TO RIDE-ON:
Squeeze latch on top of chassis. Lift rear handle up and forward.
Rotate handles up then lower body onto chassis.
Make sure the handle locks into place.
CAUTION:
LATCH
PMS 186 Black PIGUET GRAPHIC 17-1-12 Hb T1-17-115 05545942B_PLA_WalknRide_INST_FAR.OP /EPSON 18Mac 06 175
05545942B PLA STEP START WALK N RIDE - US
05545942B_PLA_WalknRide_INST_FAR OP.indd 4-5 30/01/2012 3:24 PM