Hay CRATE Series User manual

– INSTRUCTION MANUAL –
DESIGN BY GERRIT RIETWELD
DINING TABLE L180CM AND DINING TABLE L230CM
CRATE COLLECTION

 CARE AND MAINTENANCE 
With a little care you can prolong the life of your
furniture. Follow the instructions for the materials
of your specific product to make sure that it stays
in the best shape for as long as possible. The
information below is only intended as a general
guideline.
PINEWOOD WITH OUTDOOR LACQUER
This product is made from high-quality pinewood.
We have treated this product with an outdoor wa-
ter-based lacquer to make it suitable for outdoor
use. The lacquer consists of a 3-layer process; a
primer and two layers of topcoat to guarantee a
long-lasting surface treatment. Over time, the sur-
face colour and appearance will slowly change,
which is a natural process due to exposure to
sunlight and different weather conditions. The
wood has been dried to a humidity specifically
for outdoor use, which enables it to withstand
outdoor conditions. Therefore, we recommend
that it is only used outdoors to avoid risk of wood
shrinkage.
CAUTION / OUTDOOR WOODEN FURNITURE
◊ Outdoor wooden furniture must be washed
regularly to remove dust and other dirt that
might result in mould, rot, and surface
discolouration.
◊ Always remove stains quickly before they can
do any permanent damage to the furniture.
◊ Make sure to wipe off any sun cream or other
liquids from the furniture after use, as these
can leave stains on the surface if left in direct
sunlight.
◊ Wipe off the furniture if it becomes wet after
rain or snowfall as this will damage the
surface over time.
◊ Wipe off bird droppings quickly as they may
lead to permanent corrosion or staining.
◊ Please be aware that the product will always
be naturally affected by the surrounding
environment it is exposed to, and that a certain
amount of discoloration is to be expected.
◊ When you move your furniture, make sure you
lift it rather than pulling or pushing it to avoid
damaging the floor, legs and mountings.
◊ It is recommended that all screws are checked
regularly and tightened after a few weeks of use.
◊ Avoid improper use such as sitting on the back
or armrests, tilting the seats on their back legs,
putting your feet on the furniture or standing on it.
◊ Be careful not to scratch or damage the
surface with sharp objects.
◊ Avoid partially covering the surface, for
example with tablecloths, cushions or place
mats, as colour variances may appear.
CLEANING & CARE
WATERBASED LACQUER
Wipe with a clean cloth wrung in water or in a
solution of water and a neutral detergent. Remove
soap residue immediately using a clean, dry cloth.
Avoid using detergents containing silicone, as they
seal the stain in and make subsequent repairs
more difficult. Never use soft soap or solvents
such as spirit, turpentine, or acetone. Do not use
cleaning products containing alcohol, as they may
damage the surface. Avoid using scouring cream
or scouring pads, as they may scratch the surface.
RESIN
Resin bleeding is a natural occurrence in pine-
wood. When temperatures rise above 35 degrees,
a natural process begins that can cause resin to
come out of the wood. Allow the resin to weather
until it dries and oxidises, forming a white crystal-
line powder. The dried resin can then be removed
with a stiff nylon or natural bristle brush, and any
remaining residue washed off with a cloth.
STORAGE  WOOD
The lifespan of your furniture will vary depending
on the weather and type of use. We recommend
that you store it in a cool, ventilated place during
winter, protected from scratches and bumps to
ensure that no mould or rot can form. Make sure
the furniture is completely dry before putting it
away for winter storage. If you are unable to pro-
vide indoors storage for your furniture in a shed,
garage or suchlike, the furniture must be placed
under a cover so that snow or rain does not come
into contact with the wood. If a rug is used as a
cover, it should not be in contact with the wood, to
allow air to flow through to avoid any discoloura-
tion, mould or rot from forming.

Protect the table from scratches and other damage while assembling.
Two people are required to carry out this assembly.


G Dowel x12

F Bracket x1

E Bracket x1

H Screw x24  K Allen key x1

I Barrel nut x8

J Screws
M6x75mm x4
M6x50mm x4
 PARTS 

A Leg section x2  B Tabletop x1

C Cross bar x2

D Cross bar x2

1.
Connect the first cross bar

C to the leg sections

A .
Make sure the leg sections are positioned as illustrated.
Secure with screws

H and dowels

G in between.
First tighten all the screws loosely, before tightening them completely.

2.
Connect the first cross bar

D . Secure with screws

H
and dowels

G in between. First tighten all the screws loosely,
before tightening them completely.

3.
Rotate the base 180°. Connect the next cross bar

D . Secure with screws

H
and dowels

G in between. First tighten all the screws loosely,
before tightening them completely.

4.
Connect the next cross bar

D . Secure with screws

H
and dowels

G in between. First tighten all the screws loosely,
before tightening them completely.

5.
Place the base upright and insert the bracket

F from underneath.
Secure with screws

H . First tighten all the screws loosely,
before tightening them completely.

6.
Place the base on its head and insert the bracket

E from underneath.
Secure with screws

H . First tighten both the screws loosely,
before tightening them completely.

7.
Turn the base upside down and place it on the underside of the tabletop.
Insert the barrel nuts

I and the dowels

G . Make sure they are turned the same way
as illustrated.

8.
Secure the leg sections to the tabletop using screws

J .
Pay attention to the different lengths of screws.
First tighten all the screws loosely,
before tightening them completely.
50 mm
50 mm
50 mm
50 mm
75 mm
Pay attention
to the different
screw lengths
75 mm
75 mm
75 mm

9.
Secure the bracket

E to the tabletop with screws

H .

10.
After carefully placing the table upright, it is ready to use.
Retighten the screws after a few weeks of use if needed.

 CARE & MAINTENANCE 
Our Care & Maintenance offers guidance for optimal
maintenance of your HAY product. It includes advice
and instructions on cleaning and caring for specific
materials to prolong the life of your furniture.
Please find our Care & Maintenance
guide by scanning the QR code
You can find more relevant information
on Crate Dining Table by scanning the
QR code
You can also find the same information here
hay.dk/downloads