Hayward AQL-WW-P-4 User manual

Hayward Industries
400 Connell Drive, Suite 6100
Berkeley Heights, NJ 07922
Phone: [phone]
www.hayward.com
Remote Display
for Aqua Logic and Pro Logic
Owner’s Manual
Contents
Installation..............................1
Troubleshooting......................2
092037E RevC
AQL-WW-P-4
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
1
COMPATIBILITY: This display/keypad is compatible with all Pro Logic and Aqua Logic P-4 systems.
In addition, it is compatible with Aqua Logic PS-4 systems with datecodes 0311 and earlier running
main software r1.04 or lower.
Installation
Mounting
The AQL-WW-P-4 Remote Control must be mounted indoors or in a weather protected area (rain
should never hit the display/keypad). Up to 3 remote display/keypads can be installed. The display/
keypad is designed to mount onto a standard electrical utility box (ideal for new construction) or can
be mounted directly onto any wall surface. When selecting a location, note that the wire to the main
unit must be less than 500 ft (160m) long. Follow the steps below:
Remote Keypad
to remove cover
push up here
x
x
Remote Display unit
Alternative
Concealed Wiring
12
34
500 ft max
3.75 ”
4.50 ”
1
2
3
4
1. Remove display/keypad baseplate from the
cover by lifting up on the cover at the lower
end of the keypad as shown below.
2. Screw the baseplate in the desired position
(screws supplied by installer).
Wiring
The Pro Logic or Aqua Logic main unit can connect up to a maximum of 3 remote display/keypads.
Use four conductor cable (typically phone cable) to connect the remote control to the Pro Logic/
Aqua Logic Control Center as shown below. The maximum wiring distance is 500 ft (160m). Note
that the terminals on both the main unit and the remote display/keypad are numbered: Connect 1
to 1, 2 to 2, etc. Refer to diagram below.
If multiple remote controls are installed: Never connect more than 2 wires to any terminal block. Two
remotes can be wired back to the Pro Logic/Aqua Logic main unit or the second display/keypad (and
third, if applicable) can be “daisy chained” with one display/keypad wired to the next.The maximum
wire run from the main unit to the furthest remote display/keypad is 500 ft (160m).
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
2
Operation
Refer to the Pro Logic or Aqua Logic Operation Manual for complete AQL-WW-P-4 operating in-
structions.
Start-up
When power is turned on, the display backlight should immediately illuminate and the following
display should appear for a few seconds:
The x.xx is the software revision level for this particular display/keypad.
Troubleshooting
1. Display/keypad not functioning (no display, no LEDs illuminated)
If the display/keypad located on the main unit is working correctly, the most likely cause is that wires
1 and 4 are either open circuited or reversed. Check wiring. If none of the displays are working,
check that 120V power is being applied to the main control and that the 3A fuse (violet) is not blown.
2. “Communication Error” displayed
If the display/keypad on the main unit is working correctly, the most likely cause is that wires 2 and
3 are either open circuited or reversed. If all the display/keypads are showing “Communication Er-
ror”, unplug the remote display connector at the main unit and check the main display. If the main
display works properly, the problem is in the wiring or one of the remotes is defective. If the main
display keypad still does not work, the main PCB will have to be replaced.
3. Display backlight turns off after a period of time
The display backlight should always illuminate when you press any key on the unit. If it turns off
after a period of time, you can stop this by pressing the menu key (possibly multiple times) until
“Settings Menu” appears. Next press the “<” or “>” key (possibly multiple times) until “Display
Light” appears. At this point, pressing either “+” or “-“ will allow you to select either “Always On” or
“Off after 60 sec”. After you have selected the desired operation, press the “Menu” button to lock
in your setting. Note that this selection applies to this display/keypad only. Repeat the process for
each display/keypad in the system.
4. Display backlight always on
The display backlight should always illuminate when you press any key on the unit. If it remains on
after 60 seconds have elapsed since the last button push, you can stop this by pressing the menu
key (possibly multiple times) until “Settings Menu” appears. Next press the “<” or “>” key (possibly
multiple times) until “Display Light” appears. At this point, pressing either “+” or “-“ will allow you
select either “Always On” or “Off after 60 sec”. After you have selected the desired operation, press
the “Menu” button to lock in your setting. Note that this selection applies to this display/keypad only.
Repeat the process for each display/keypad in the system.
PRO LOGIC
rx.xx
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

For further information or consumer
technical support, visit our website at
www.hayward.com
Hayward is a registered trademark and Aqua Logic and Pro Logic
are trademarks of Hayward Industries, Inc. © 2019 Hayward Industries, Inc.
All other trademarks not owned by Hayward are the property of their respective owners.
Hayward is not in any way affiliated with or endorsed by those third parties.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS