Hayward AQL2-WB-PS-4 User manual

Hayward Pool Products
620 Division Street, Elizabeth NJ 07207
Phone: [phone]
www.hayward.com
Remote Display
for Aqua Logic and Pro Logic
Owner’s Manual
Contents
Installation..............................2
Troubleshooting.......................5
Warranty..................................7
092147C RevB
AQL2-WB-PS-4 AQL2-WW-PS-4
AQL2-WB-PS-8 AQL2-WW-PS-8
AQL2-WB-PS-16 AQL2-WW-PS-16

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
2
COMPATIBILITY: This remote display is compatible with all Pro Logic PS-4/8/16 models and for
all Aqua Logic PS-4/8/16 systems running main software r2.00 or higher.
Installation
Mounting
The AQL2-Wx-PS-x Remote Display must be mounted indoors or in a weather protected area (rain
should never hit the remote display). Up to 3 remote displays can be installed. The remote display is
designed to mount onto a standard electrical utility box (same size as used for a triple light switch)
or can be mounted directly onto any wall surface.When selecting a location, note that the wire to the
Pro Logic/Aqua Logic main unit must be no more than 500 ft (160m) long. Follow the steps below:
1. Remove the remote display baseplate from the cover by inserting a screwdriver in the slot
shown below. Lift up on the cover while pushing gently with the screwdriver.
2. If bezel will be used, snap baseplate into bezel before mounting.
3. Screw the baseplate in the desired position (screws supplied by installer).
Push Screwdriver
blade through slot
and pull up
cover
Bezel
(use is optional)

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
3
Wiring
The Pro Logic or Aqua Logic main unit can connect up to a maximum of 3 remote displays. Use four
conductor cable (typically phone cable) to connect the remote display keypad with the Pro Logic/
Aqua Logic Control Center as shown below. The maximum wiring distance is 500 ft (160m). Note
that the terminals on both the Pro Logic/Aqua Logic main unit and the remote display are numbered:
Connect 1 to 1, 2 to 2, etc.
If multiple remote displays are installed: Never connect more than 2 wires to any terminal block.Two
remotes can be wired back to the Pro Logic/Aqua Logic main unit or the second remote display (and
third, if applicable) can be “daisy chained” with one remote display wired to the next. The maximum
wire run from the Pro Logic/Aqua Logic main unit to the furthest remote display is 500 ft (160m).
Wired Remote
Display unit
Aqua Logic Control Center
500 ft max
1
2
3
4
Connect screw terminals
“1” to “1”, “2” to “2”, etc.
1234
Wired Remote
Display unit
Pro Logic Control Center
500 ft max
1
2
3
4
Connect screw terminals
“1” to “1”, “2” to “2”, etc.
1234

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
4
Operation
When power is turned on, all the LED indicators will flash briefly, the display backlight will illumi-
nate, and the following display will appear for a short period of time:
The “r4.00” is the software revision level. The actual revision level for your remote display may be
different.
Refer to the Pro Logic or Aqua Logic Operation Manual for complete operating instructions.
Goldline Aqua Logic
Display r4.00
Goldline Pro Logic
Display r4.00

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
5
Troubleshooting
1. Remote display not functioning (no display, no LEDs illuminated).
If the display/keypad located on the main unit is working correctly, the most likely cause is
that wires 1 and 4 are either open circuited or reversed. Check wiring. If none of the displays
are working, check that 120V power is being applied to the main control and that the 3A fuse
(violet) is not blown.
2. Display backlight turns off after a period of time
The display backlight should always illuminate when you press any key on the unit. If it turns off
after a period of time, you can stop this by pressing the menu key (possibly multiple times) until
“Settings Menu” appears. Next press the “<” or “>” key (possibly multiple times) until “Display
Light” appears. At this point, pressing either “+” or “-“ will allow you to select either “Always
On” or “On for 60 sec.”.After you have selected the desired operation, press the “Menu” button
to lock in your setting. Note that this selection applies to this display/keypad only. Repeat the
process for each remote display in the system.
3. Display backlight always on
The display backlight should always illuminate when you press any key on the unit. If it remains
on after 60 seconds have elapsed since the last button push, you can stop this by pressing
the menu key (possibly multiple times) until “Settings Menu” appears. Next press the “<” or
“>” key (possibly multiple times) until “Display Light” appears. At this point, pressing either
“+” or “-“ will allow you select either “Always On” or “On for 60 sec.”. After you have selected
the desired operation, press the “Menu” button to lock in your setting. Note that this selection
applies to this remote display only. Repeat the process for each remote display in the system.
4.
The remote display received data from an Aqua Logic system running software earlier than
r2.00. This keypad is not compatible with these systems. Another cause for this problem may
be that the local display/keypad in the main Pro Logic/Aqua Logic control unit is not connected
or not functioning. If this is the case, connect and/or replace the local display keypad and then
cycle power to the Pro Logic/Aqua Logic off and then back on to reset the system. If you are
unable to find the problem, contact the Hayward Technical Support department Monday through
Friday, from 8AM to 8PM eastern time.
5.
The remote display is not receiving any communication from the Pro Logic/Aqua Logic main
control unit. The most likely cause of this problem is a broken wire or “open circuit” in wires “2”
and/or “3” in the cable between the remote display and the Pro Logic/Aqua Logic main control
unit. If you are unable to find the problem, contact the Hayward Technical Support department
Monday through Friday, from 8AM to 8PM eastern time.
Communication Err 1
call 908-355-7995
Communication 2
call
Err
908-355-7995

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
6
6.
The remote display is receiving data from the main Pro Logic/Aqua Logic control unit however
that data contains errors and is unusable. The most likely cause of this problem is that wires
“2” and “3” in the cable between the control unit and the remote display are crossed. If you
are unable to find the problem, contact the Hayward Technical Support department Monday
through Friday, from 8AM to 8PM eastern time.
7.
An internal problem has occurred in the remote display. Remove the remote display from the
wall mount base (see diagram on page 1) and write down the model number and serial number
of the remote display. Next, call the Hayward Technical Support department (Monday through
Friday, from 8AM to 8PM eastern time) to find out how to obtain a replacement remote display.
Communication 3
call
Err
908-355-7995
Display Error 1
call 908-355-7995
Display Error 2
call 908-355-7995

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
7
LIMITEDWARRANTY (effective 03/01/12) Hayward warrants its Pro Logic,OnCommand and E-Command
pool automation products as well as its Aqua Rite, Aqua Rite Pro, Aqua Plus and SwimPure chlorination
products to be free of defects in materials and workmanship, under normal use and service, for a period
of three (3) years. Hayward also warrants its Aqua Trol chlorination products to be free of defects in
materials and workmanship, under normal use and service for a period of one (1) year. These warran-
ties are applicable from the initial date of purchase on private residential swimming pools in the US and
Canada. Installations of product for use on commercial pools in the US and Canada is covered for a
period of one (1) year for defects in materials and workmanship. Hayward warrants all accessories and
replacement parts for the above-identified pool automation and chlorination products for a period of one
(1) year. Accessories also include remotes, actuators, base stations, temperature sensors, flow switches
and chemistry probes. Each of these warranties is not transferable and applies only to the original owner.
Hayward shall not be responsible for cartage, removal, repair or installation labor or any other such costs
incurred in obtaining warranty replacements or repair.
Proof of purchase is required for warranty service. If written proof of purchase is not provided, the
manufacturing date code will be the sole determinant of the date of installation of the product. To obtain
warranty service or repair, please contact the place of purchase or the nearest Hayward authorized war-
ranty service center. For more information on authorized service centers please contact the Hayward
Technical Service Support Center (61 Whitecap Road, North Kingstown RI, 02852) or visit the Hayward
web site at www.hayward.com.
WARRANTY EXCLUSIONS:
1. Material supplied or workmanship performed by others in process of installation.
2.Damage resulting from improper installation including installation on pools larger than the product rating.
3. Problems resulting from failure to install, operate or maintain the product(s) in accordance with the
recommendations contained in the owners manual(s).
4. Problems resulting from failure to maintain pool water chemistry in accordance with the recommenda-
tions in the owners manual(s).
5. Problems resulting from tampering, accident, abuse, negligence, unauthorized repairs or alternations,
fire, flood, lightning, freezing, external water, degradation of natural stone used in or immediately adjacent
to a pool or spa, war or acts of God.
6. Use of a non-genuine Hayward replacement salt chlorination cell on any Hayward automation or
chlorination product will void the warranty for that product.
The express limited warranty above constitutes the entire warranty of Hayward Pool Products with
respect to its products and is in lieu of all other warranties expressed or implied, including warranties of
merchantability or fitness for a particular purpose. In no event shall Hayward Pool products be responsible
for any consequential, special or incidental damages of any nature. Some states do not allow a limitation
on how long an implied warranty lasts, or the exclusion of incidental or consequential damages, so the
above limitation may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights, which vary from state to state.

For further information or consumer
technical support, visit our website at
www.hayward.com
Hayward is a registered trademark and Aqua Trol
are trademarks of Hayward Industries, Inc. © 2016 Hayward Industries, Inc.
All other trademarks not owned by Hayward are the property of their respective owners.
Hayward is not in any way affiliated with or endorsed by those third parties.