HBS GQ-20A1 User manual

HBS GQ-20A1
Laser Marking System Installation Guide
HBS Tech

1. After unpacking the machine, please check the accessories:
①safety warning led light ②the top cover ③the bottom supply unit ④laser marking
head ⑤industrial tablet ⑥computer mount bracket ⑦laser marking head bracket

2. The seven screw holes on the supply unit table are fixed. Place the laser marking
head as shown below.
3. When installing the top cover, to avoid unnecessary damage to the machine, do not
proceed operation with only one person.
First, open up the front door of the top cover, as shown below.

4. Place the top cover smoothly and move the laser marking head to a safe place.
Throughout the installation process, please always pay attention to protect the laser
marking head, and the black fiber optic cable connected to the laser marking head, do
not trample.
5. Inside the top cover also has seven round holes, as shown below.

6. Open doors on both sides of the top cover to facilitate the tightening screw process,
as shown below.

7. Tighten the top cover and the supply unit with 7 hexagon screws, as shown below.
8. The green plug is the safety led light connector, and the big black one connects the
button sets on the front panel of the top cover. The other small plug is for the USB cable
communication.
All the plugs should go through the hole, find the corresponding socket, and tightened
as shown below.
From left to right in the picture, followed by USB communication cable, safety led light
connector, top cover panel button sets.

9. Connect the 2 safety led light connectors, and tighten the green plug sets with
screwdrivers, and tighten the safety led light base with 4 screws, as shown below.

10. Laser marking head bracket and laser marking head installation. First, plug in the 8-
pin connector, then place the bracket on the desktop of the supply unit and align the 4
holes between the base and desktop nicely, and use 4 screws to tighten them. Then
place the laser marking head on the bracket, align the 6 screw holes with 6 holes on the
bracket, tighten them, as shown below.

11. Install the industrial tablet with mount bracket, as shown below.
12. Plug the 4-pin power cord into the socket, rotating to lock-in position, as shown
below.

13. 3-pin head cable is for the footswitch, insert into the socket, rotating to lock-in
position, as shown below.
14. 8-pin head dual plug cable is for the rotary clamp accessory(optional), as shown
below.

15. The industrial tablet power supply can be installed in two ways, ①Use the 2-pin
dual plug connect the industrial tablet USB port with the top cover USB port, as shown
below. ②Use the standard power supply cable, you can directly plug into the power
outlet.

16. USB communication cable connection, connect the top cover USB port with
industrial tablet USB port, as shown below.

17. Connect the power supply to the user-supplied voltage, check the circuit breaker,
make sure it is switched "on" position to ensure the standard power supply function, as
shown below.
18. SYSTEM STARTUP PROCEDURE
Caution! Please strictly follow this order.
1. Press the "Control Power" button.
2. Turn on the "Laser Power" switch.
SYSTEM SHUTDOWN PROCEDURE
Caution! Please strictly follow this order.
1. Turn off the "Laser Power" switch.
2. Press the "Control Power" button.

19. Under normal, not marking condition, the safety led light is green. When the
machine is marking, the safety led light will turn to yellow, press the emergency stop
switch, the safety led light will turn red and accompanied by high pitch noise.

20. At the bottom side of the laser marking head, there is a focus finder switch. This
focus finder is designed for smooth and precise focal positioning. Press the Z-AXIS
button up and down manually. The laser marking head will automatically lift up and
down. When the two red dots are overlapped together and become one, the laser
marking head has found the focal position, as shown below.

21. Marking.
Four ways to mark:
①Press the MARK button on both side of the top cover, as shown below.
②Press the keypad F2 button
③Press foot switch
④Use industrial tablet software command
22. USB communication cable connection instructions.
There are two USB communication cables which are designed to connect the control
board inside the supply unit in different circumstances.
Customers can choose the connection method as needed.

①Using the USB port on the side of the top cover. Find the USB cable which tied
together with the black line sets, as shown below.
②Using the USB port on the desktop of the supply unit, please select the
corresponding USB cable, and plug it in, as shown below.

23. Rotary clamp cable connection description.
There are two ways for the user to choose, respectively.
On the desktop of the supply unit, and the rear side of the supply unit, as shown below.
24. For laser marking machine software instructions, please refer to the laser marking
software user manual.