Rohde & Schwarz ZVH4 User manual

R&S®ZVH
Cable and Antenna Analyzer
Operating Manual
1309.6946.12 – 09
Operating Manual

The Operating Manual describes the following R&S®ZVH models and options
●R&S ZVH4 (1309.6800.24)
●R&S ZVH8 (1309.6800.28)
●R&S ZVH-K1 (1309.6823.02)
●R&S ZVH-K9 (1309.6852.02)
●R&S ZVH-K19 (1304.5987.02))
●R&S ZVH-K14 (1309.7007.02)
●R&S ZVH-K29 (1304.0491.02)
●R&S ZVH-K39 (1309.6830.02)
●R&S ZVH-K42 (1309.6846.02)
●R&S ZVH-K45 (1309.6998.02)
The contents of this manual correspond to firmware version 1.60 and higher.
© 2017 Rohde & Schwarz GmbH & Co. KG
Muehldorfstr. 15, 81671 Munich. Germany
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
Internet: http://www.rohde-schwarz.com
81671 Munich, Germany
Subject to change – Data without tolerance limits is not binding.
R&S®is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
Trade names are trademarks of the owners.
Throughout this manual, products from Rohde & Schwarz are indicated without the ®symbol, e.g. R&S®ZVH is indicated as
R&S ZVH.

R&S ZVH Basic Safety Instructions
1175.6603.12 - 02 i
Basic Safety Instructions
Always read through and comply with the following safety instructions!
All plants and locations of the Rohde & Schwarz group of companies make every effort
to keep the safety standards of our products up to date and to offer our customers the
highest possible degree of safety. Our products and the auxiliary equipment they
require are designed, built and tested in accordance with the safety standards that
apply in each case. Compliance with these standards is continuously monitored by our
quality assurance system. The product described here has been designed, built and
tested in accordance with the attached EC Certificate of Conformity and has left the
manufacturer’s plant in a condition fully complying with safety standards. To maintain
this condition and to ensure safe operation, you must observe all instructions and
warnings provided in this manual. If you have any questions regarding these safety
instructions, the Rohde & Schwarz group of companies will be happy to answer them.
Furthermore, it is your responsibility to use the product in an appropriate manner. This
product is designed for use solely in industrial and laboratory environments or, if
expressly permitted, also in the field and must not be used in any way that may cause
personal injury or property damage. You are responsible if the product is used for any
intention other than its designated purpose or in disregard of the manufacturer's
instructions. The manufacturer shall assume no responsibility for such use of the
product.
The product is used for its designated purpose if it is used in accordance with its
product documentation and within its performance limits (see data sheet,
documentation, the following safety instructions). Using the product requires technical
skills and a basic knowledge of English. It is therefore essential that only skilled and
specialized staff or thoroughly trained personnel with the required skills be allowed to
use the product. If personal safety gear is required for using Rohde & Schwarz
products, this will be indicated at the appropriate place in the product documentation.
Keep the basic safety instructions and the product documentation in a safe place and
pass them on to the subsequent users.
Symbols and safety labels
Observe product
documen-tation
Danger of
electric shock
Warning! Hot
surface
PE terminal
Ground
Ground
terminal
Attention!
Electrostatic
sensitive devices

R&S ZVH Basic Safety Instructions
1175.6603.12 - 02 ii
Observing the safety instructions will help prevent personal injury or damage of any
kind caused by dangerous situations. Therefore, carefully read through and adhere to
the following safety instructions before and when using the product. It is also absolutely
essential to observe the additional safety instructions on personal safety, for example,
that appear in relevant parts of the product documentation. In these safety instructions,
the word "product" refers to all merchandise sold and distributed by the Rohde &
Schwarz group of companies, including instruments, systems and all accessories.
Tags and their meaning
The following signal words are used in the product documentation in order to warn the
reader about risks and dangers.
indicates a hazardous situation which, if not avoided, will
result in death or serious injury.
indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
indicates the possibility of incorrect operation which can
result in damage to the product.
In the product documentation, the word ATTENTION is used
synonymously.
These tags are in accordance with the standard definition for civil applications in the
European Economic Area. Definitions that deviate from the standard definition may
also exist in other economic areas or military applications. It is therefore essential to
make sure that the tags described here are always used only in connection with the
related product documentation and the related product. The use of tags in connection
with unrelated products or documentation can result in misinterpretation and in
personal injury or material damage.
Operating states and operating positions
The product may be operated only under the operating conditions and in the positions
specified by the manufacturer. If the manufacturer's specifications are not observed,
this can result in electric shock, fire and/or serious personal injury or death. Applicable
local or national safety regulations and rules for the prevention of accidents must be
observed in all work performed.
1. The R&S ZVH is protected against dripping water and dust (IP degree 51). Unless
otherwise specified, the following requirements apply to Rohde & Schwarz
products: predefined operating position is always with the housing floor facing
down, IP protection 2X, pollution severity 2, overvoltage category 2, use only in
enclosed spaces, max. operation altitude 4600 m above sea level, max. transport
altitude 12000 m above sea level. A tolerance of ±10% shall apply to the nominal
voltage and of ±5% to the nominal frequency.

R&S ZVH Basic Safety Instructions
1175.6603.12 - 02 iii
2. Do not place the product on heat-generating devices such as radiators or fan
heaters. The ambient temperature must not exceed the maximum temperature
specified in the product documentation or in the data sheet. Product overheating
can cause electric shock, fire and/or serious personal injury or death.
Electrical Safety
If the information on electrical safety is not observed either at all to the extent
necessary, electric shock, fire and/or serious personal injury or death may occur.
1. Prior to switching on the product, always ensure that the nominal voltage setting on
the power supply matches the nominal voltage of the AC supply network.
2. If the product does not have a power switch for disconnection from the AC supply
network, the plug of the connecting cable is regarded as the disconnecting device.
In such cases, always ensure that the power plug is easily reachable and
accessible at all times (corresponding to the length of connecting cable, approx.
2 m). Functional or electronic switches are not suitable for providing disconnection
from the AC supply network. If products without power switches are integrated into
racks or systems, a disconnecting device must be provided at the system level.
3. Never use the product if the power cable is damaged. Check the power cable on a
regular basis to ensure that it is in proper operating condition. By taking
appropriate safety measures and carefully laying the power cable, you can ensure
that the cable will not be damaged and that no one can be hurt by, for example,
tripping over the cable or suffering an electric shock.
4. The product may be operated only from TN/TT supply networks fused with max.
16 A (higher fuse only after consulting with the Rohde & Schwarz group of
companies).
5. Do not insert the plug into sockets that are dusty or dirty. Insert the plug firmly and
all the way into the socket. Otherwise, sparks that result in fire and/or injuries may
occur.
6. Do not overload any sockets, extension cords or connector strips; doing so can
cause fire or electric shocks.
7. For measurements in circuits with voltages Vrms > 30 V, suitable measures (e.g.
appropriate measuring equipment, fusing, current limiting, electrical separation,
insulation) should be taken to avoid any hazards.
8. Ensure that the connections with information technology equipment, e.g. PCs or
other industrial computers, comply with the IEC60950-1/EN60950-1 or IEC61010-
1/EN 61010-1 standards that apply in each case.
9. Unless expressly permitted, never remove the cover or any part of the housing
while the product is in operation. Doing so will expose circuits and components and
can lead to injuries, fire or damage to the product.
10. For permanently installed equipment without built-in fuses, circuit breakers or
similar protective devices, the supply circuit must be fused in such a way that
anyone who has access to the product, as well as the product itself, is adequately
protected from injury or damage.

R&S ZVH Basic Safety Instructions
1175.6603.12 - 02 iv
11. Use suitable overvoltage protection to ensure that no overvoltage (such as that
caused by a bolt of lightning) can reach the product. Otherwise, the person
operating the product will be exposed to the danger of an electric shock.
12. Any object that is not designed to be placed in the openings of the housing must
not be used for this purpose. Doing so can cause short circuits inside the product
and/or electric shocks, fire or injuries.
13. Unless specified otherwise, products are not liquid-proof (see also section
"Operating states and operating positions", item 1. Therefore, the equipment must
be protected against penetration by liquids. If the necessary precautions are not
taken, the user may suffer electric shock or the product itself may be damaged,
which can also lead to personal injury.
14. Prior to cleaning the product, disconnect it completely from the power supply (e.g.
AC supply network or battery). Use a soft, non-linting cloth to clean the product.
Never use chemical cleaning agents such as alcohol, acetone or diluents for
cellulose lacquers.
Operation
1. Operating the products requires special training and intense concentration. Make
sure that persons who use the products are physically, mentally and emotionally fit
enough to do so; otherwise, injuries or material damage may occur. It is the
responsibility of the employer/operator to select suitable personnel for operating
the products.
2. Before you move or transport the product, read and observe the section titled
"Transport".
3. As with all industrially manufactured goods, the use of substances that induce an
allergic reaction (allergens) such as nickel cannot be generally excluded. If you
develop an allergic reaction (such as a skin rash, frequent sneezing, red eyes or
respiratory difficulties) when using a Rohde & Schwarz product, consult a
physician immediately to determine the cause and to prevent health problems or
stress.
4. Before you start processing the product mechanically and/or thermally, or before
you take it apart, be sure to read and pay special attention to the section titled
"Waste disposal", item 1.
5. Depending on the function, certain products such as RF radio equipment can
produce an elevated level of electromagnetic radiation. Considering that unborn
babies require increased protection, pregnant women must be protected by
appropriate measures. Persons with pacemakers may also be exposed to risks
from electromagnetic radiation. The employer/operator must evaluate workplaces
where there is a special risk of exposure to radiation and, if necessary, take
measures to avert the potential danger.
6. Should a fire occur, the product may release hazardous substances (gases, fluids,
etc.) that can cause health problems. Therefore, suitable measures must be taken,
e.g. protective masks and protective clothing must be worn.

R&S ZVH Basic Safety Instructions
1175.6603.12 - 02 v
Repair and service
1. The product may be opened only by authorized, specially trained personnel.
Before any work is performed on the product or before the product is opened, it
must be disconnected from the AC supply network. Otherwise, personnel will be
exposed to the risk of an electric shock.
2. Adjustments, replacement of parts, maintenance and repair may be performed only
by electrical experts authorized by Rohde & Schwarz. Only original parts may be
used for replacing parts relevant to safety (e.g. power switches, power
transformers, fuses). A safety test must always be performed after parts relevant to
safety have been replaced (visual inspection, PE conductor test, insulation
resistance measurement, leakage current measurement, functional test). This
helps ensure the continued safety of the product.
Batteries and rechargeable batteries/cells
If the information regarding batteries and rechargeable batteries/cells is not observed
either at all or to the extent necessary, product users may be exposed to the risk of
explosions, fire and/or serious personal injury, and, in some cases, death. Batteries
and rechargeable batteries with alkaline electrolytes (e.g. lithium cells) must be
handled in accordance with the EN 62133 standard.
1. Cells must not be taken apart or crushed.
2. Cells or batteries must not be exposed to heat or fire. Storage in direct sunlight
must be avoided. Keep cells and batteries clean and dry. Clean soiled connectors
using a dry, clean cloth.
3. Cells or batteries must not be short-circuited. Cells or batteries must not be stored
in a box or in a drawer where they can short-circuit each other, or where they can
be short-circuited by other conductive materials. Cells and batteries must not be
removed from their original packaging until they are ready to be used.
4. Keep cells and batteries out of the hands of children. If a cell or a battery has been
swallowed, seek medical aid immediately.
5. Cells and batteries must not be exposed to any mechanical shocks that are
stronger than permitted.
6. If a cell develops a leak, the fluid must not be allowed to come into contact with the
skin or eyes. If contact occurs, wash the affected area with plenty of water and
seek medical aid.
7. Improperly replacing or charging cells or batteries that contain alkaline electrolytes
(e.g. lithium cells) can cause explosions. Replace cells or batteries only with the
matching Rohde & Schwarz type (see parts list) in order to ensure the safety of the
product.
8. Cells and batteries must be recycled and kept separate from residual waste.
Rechargeable batteries and normal batteries that contain lead, mercury or
cadmium are hazardous waste. Observe the national regulations regarding waste
disposal and recycling.

R&S ZVH Basic Safety Instructions
1175.6603.12 - 02 vi
Transport
1. Handles on the products are designed exclusively to enable personnel to transport
the product. It is therefore not permissible to use handles to fasten the product to
or on transport equipment such as cranes, fork lifts, wagons, etc. The user is
responsible for securely fastening the products to or on the means of transport or
lifting. Observe the safety regulations of the manufacturer of the means of
transport or lifting. Noncompliance can result in personal injury or material
damage.
2. If you use the product in a vehicle, it is the sole responsibility of the driver to drive
the vehicle safely and properly. The manufacturer assumes no responsibility for
accidents or collisions. Never use the product in a moving vehicle if doing so could
distract the driver of the vehicle. Adequately secure the product in the vehicle to
prevent injuries or other damage in the event of an accident.
Waste disposal
1. If products or their components are mechanically and/or thermally processed in a
manner that goes beyond their intended use, hazardous substances (heavy-metal
dust such as lead, beryllium, nickel) may be released. For this reason, the product
may only be disassembled by specially trained personnel. Improper disassembly
may be hazardous to your health. National waste disposal regulations must be
observed.

R&S ZVH Informaciones Elementales de Seguridad
1175.6603.17 - 02 i
Informaciones Elementales de Seguridad
Es imprescindible leer y observar las siguientes instrucciones e informaciones
de seguridad!
El principio del grupo de empresas Rohde & Schwarz consiste en tener nuestros
productos siempre al día con los estándares de seguridad y de ofrecer a nuestros
clientes el máximo grado de seguridad. Nuestros productos y todos los equipos
adicionales son siempre fabricados y examinados según las normas de seguridad
vigentes. Nuestro sistema de garantía de calidad controla constantemente que sean
cumplidas estas normas. El presente producto ha sido fabricado y examinado según el
certificado de conformidad adjunto de la UE y ha salido de nuestra planta en estado
impecable según los estándares técnicos de seguridad. Para poder preservar este
estado y garantizar un funcionamiento libre de peligros, el usuario deberá atenerse a
todas las indicaciones, informaciones de seguridad y notas de alerta. El grupo de
empresas Rohde & Schwarz está siempre a su disposición en caso de que tengan
preguntas referentes a estas informaciones de seguridad.
Además queda en la responsabilidad del usuario utilizar el producto en la forma
debida. Este producto está destinado exclusivamente al uso en la industria y el
laboratorio o, si ha sido expresamente autorizado, para aplicaciones de campo y de
ninguna manera deberá ser utilizado de modo que alguna persona/cosa pueda sufrir
daño. El uso del producto fuera de sus fines definidos o sin tener en cuenta las
instrucciones del fabricante queda en la responsabilidad del usuario. El fabricante no
se hace en ninguna forma responsable de consecuencias a causa del mal uso del
producto.
Se parte del uso correcto del producto para los fines definidos si el producto es
utilizado conforme a las indicaciones de la correspondiente documentación del
producto y dentro del margen de rendimiento definido (ver hoja de datos,
documentación, informaciones de seguridad que siguen). El uso del producto hace
necesarios conocimientos técnicos y ciertos conocimientos del idioma inglés. Por eso
se debe tener en cuenta que el producto solo pueda ser operado por personal
especializado o personas instruidas en profundidad con las capacidades
correspondientes. Si fuera necesaria indumentaria de seguridad para el uso de
productos de Rohde & Schwarz, encontraría la información debida en la
documentación del producto en el capítulo correspondiente. Guarde bien las
informaciones de seguridad elementales, así como la documentación del producto, y
entréguelas a usuarios posteriores.
Símbolos y definiciones de seguridad
Ver documen-
tación de
producto
Peligro de
golpe de
corriente
¡Advertencia!
Superficie
caliente
Conexión a
conductor
protector
Conexión a
tierra
Conexión a
masa
conductora
¡Cuidado! Elementos
de construcción con
peligro de carga
electroestática

R&S ZVH Informaciones Elementales de Seguridad
1175.6603.17 - 02 ii
Tener en cuenta las informaciones de seguridad sirve para evitar en lo posible
lesiones o daños por peligros de toda clase. Por eso es imprescindible leer
detalladamente y comprender por completo las siguientes informaciones de seguridad
antes de usar el producto, y respetarlas durante el uso del producto. Deberán tenerse
en cuenta todas las demás informaciones de seguridad, como p. ej. Las referentes a la
protección de personas, que encontrarán en el capítulo correspondiente de la
documentación del producto y que también son de obligado cumplimiento. En las
presentes informaciones de seguridad se recogen todos los objetos que distribuye el
grupo de empresas Rohde & Schwarz bajo la denominación de "producto", entre ellos
también aparatos, instalaciones así como toda clase de accesorios.
Palabras de señal y su significado
PELIGRO identifica un peligro inminente con riesgo elevado
que provocará muerte o lesiones graves si no se evita.
ADVERTENCIA identifica un posible peligro con riesgo
medio de provocar muerte o lesiones (graves) si no se evita.
ATENCIÓN identifica un peligro con riesgo reducido de
provocar lesiones leves o moderadas si no se evita.
AVISO indica la posibilidad de utilizar mal el producto y,
como consecuencia, dañarlo.
En la documentación del producto se emplea de forma
sinónima el término CUIDADO.
Las palabras de señal corresponden a la definición habitual para aplicaciones civiles
en el area económica europea. Pueden existir definiciones diferentes a esta definición
en otras áreas económicas o en aplicaciones militares. Por eso se deberá tener en
cuenta que las palabras de señal aquí descritas sean utilizadas siempre solamente en
combinación con la correspondiente documentación del producto y solamente en
combinación con el producto correspondiente. La utilización de las palabras de señal
en combinación con productos o documentaciones que no les correspondan puede
llevar a interpretaciones equivocadas y tener por consecuencia daños en personas u
objetos.
Estados operativos y posiciones de funcionamiento
El producto solamente debe ser utilizado según lo indicado por el fabricante respecto a
los estados operativos y posiciones de funcionamiento sin que se obstruya la
ventilación. Si no se siguen las indicaciones del fabricante, pueden producirse
choques eléctricos, incendios y/o lesiones graves con posible consecuencia de
muerte. En todos los trabajos deberán ser tenidas en cuenta las normas nacionales y
locales de seguridad del trabajo y de prevención de accidentes.