HDCVT TECHNOLOGY HBT-E70S User manual

HDMI Extender over Cat5e/Cat6
(HD BaseT)
User manual
VER: 1.1s

1
Thank you for purchasing this product. For optimum performance and safety, please read
the instruction carefully before connecting, operating or adjusting this product. Please
keep the manual for future reference.
Caution
The extender using UTP termination, which follows the standard of direct
interconnection method.

2
Advanced:
The extender will start protection mode automatically when using UTP termination,
which follows the standard of cross interconnection method.

3
I. Introduction
The cat5e/cat6 HDMI Extender is a tool which can extend your HDMI signal over
230fts/70meters to a compatible display. It is designed to convert HDMI signal to

4
standard HD BaseT signal which can be transmitted by LAN cable. It also supports
Transfer Bidirectional Infrared control signal together with the HDMI signal, so you can
control the Source in the Sink side which is 230fts outside, also you can control the Sink
in the Source side which is 230fts outside by using the HDMI Extender.
II. Features
1. POE (Power Over Ethernet) function is supported, either TX or RX is powered
by24V@1A power supply, the another does not need power supply from the DC
jack. POE Power consumption is less than 10W. ※See the description 1
2. Use single UTP LAN cable (CAT-5E/6) to substitute HDMI cable to achieve long
distance transmission.
3. UTP termination follows the standard of direct interconnection method.
4. Transmission distance: ※Ov e r CA T 6 ca b l e

5
70 meters: 1080P @60Hz36bit; 3D1080P@30Hz36bit;
40 meters: 1080P @60Hz@48bit; 1080P @120Hz@24bit;
3D1080P@60Hz@36bit; 4K x 2K@30Hz@24bit.
5. Support display resolutions up to 4K x 2K@30Hz
6. Full HD support: 1080p@60Hz@48 bit/pixels, 1080p@120Hz@24 bit/pixels,
3D 1080P60Hz and 4K x 2K@30Hz@24bit
7. Transfer Bidirectional Infrared control signal together with the HDMI signal.
※See the description 2.
8. Transfer Bidirectional RS232 control signal together with the HDMI signal.
※See the description 3.
III. Package
1. HDMI Extender Transmitter ------------------------------------------ 1PC
2. HDMI Extender Receiver ---------------------------------------------- 1PC

6
3. Wideband IR Tx --------------------------------------------------------- 2PCS
4. Wideband IR Rx --------------------------------------------------------- 2PCS
5. 24V1A DC Power Supply ---------------------------------------------- 1PC
6. Operation Manual ------------------------------------------------------ 1PC
7. Mounting ears------------------------------------------------------------4PCS
IV. Specifications
1. Frequency Bandwidth 297MHz[10.2Gbps]
2. Transmitter Input/Output 1x HDMI Female port/1xCAT6
1x IR Tx/1x IR Rx/1xPhoenix
3. Receiver Input/Output Ports 1xHDMI Female port/1xCAT6
1x IR Tx/1x IR Rx/1xPhoenix
4. Power Supply DC 24V 1A

7
5. ESD Protection ± 8kV (air-gap discharge)
Human Body Model: ± 4kV (contact discharge)
6. Dimensions (mm) 65(W) X 115 (D) X 17 (H)
7. Weight 200g x 2
8. Operating Temperature 0°C ~ 40°C / 32°F ~ 104°F
9. Storage Temperature -20°C ~ 60°C / -4°F ~ 140°F
10. Relative Humidity 20~90% RH (Non-condensing)
11. Power Consumption (Max) 20W

8
V. Operation controls and Functions
Transmitter
1. POWER: This LED illuminates when the device is connected with power supply.
2. DC 24V: Plug the 24V DC power supply into the unit.
3. HD BaseT OUT: Standard HD BaseT signal output port. Connect HD BaseT

9
receiver with a UTP cable following the standard of direct interconnection method.
4. HDMI IN: HDMI input port. This slot is where you connect the HDMI source.
5. IR IN:Channel 2 IR Receiver.Connect with Wideband IR Rx.
6. IR OUT: Channel 1 IR Transmitter.Connect with Wideband IR Tx.
7. RS232: Phoenix jack provide Serial port control signal from receiver or to receiver.
8. Connection Signal Indicator Lamp
※Illuminate: The Transmitter and Receiver are in good connections status.
※Flashing: The Transmitter and Receiver are in poor connections status.
※Dark: The Transmitter and Receiver are not connected.
9. Data Signal Indicator Lamp
※Illuminate: The HDMI signal with HDCP.
※Flashing: The HDMI signal without HDCP.
※Dark: No HDMI signal.

10
Receiver
1. POWER: This LED illuminates when the device is connected with power supply
2. DC 24V: Plug the 24V DC power supply into the unit.
3. HD BaseT IN:Standard HD BaseT signal input port. Connect HD BaseT transmitter
with a UTP cable following the standard of direct interconnection method.

11
4. HDMI OUT:HDMI output port. This slot is where you connect the HDTV or
monitor with HDMI cable.
5. IR IN:Channel 1 IR Receiver.Connect with Wideband IR Rx.
6. IR OUT:Channel 2 IR Transmitter.Connect with Wideband IR Tx.
7. RS232: Phoenix jack provide Serial port control signal from receiver or to receiver.
8. Connection Signal Indicator Lamp
※Illuminate: The Transmitter and Receiver are in good connections status.
※Flashing: The Transmitter and Receiver are in poor connections status.
※Dark: The Transmitter and Receiver are not connected.
9. Data Signal Indicator Lamp
※Illuminate: The HDMI signal with HDCP.
※Flashing: The HDMI signal without HDCP.
※Dark: No HDMI signal.

12
※Description 1
POE(Power Over Ethernet) Application Example

13
※Description 2
Bidirectional Infrared control Application Example

14
※Description 3
Bidirectional RS232 control Application Example

15
VI. Application Example