HE-VA Top-Strigle User manual

18 Back to the table of contents
UK
Manual no. 8000121-03 110221

Contents
EC DECLARATION OF CONFORMITY .......................................................................................................0
Delivery Check ..................................................................................................................................................1
Machine description...........................................................................................................................................1
Technical specifications.................................................................................................................................2
Working with the Top-Strigle.........................................................................................................................2
Safety around the Top-Strigle............................................................................................................................3
Safety Instructions, regarding Hydraulic System ..............................................................................................4
Markings on the machine...................................................................................................................................5
Maintenance.......................................................................................................................................................6
Disposal..............................................................................................................................................................6
Notes..................................................................................................................................................................7
Spareparts list.....................................................................................................................................................8
Right section, 5-bars w/Ø16 mm long finger tine 6.0 - 7,0 - 8,0 m...............................................................8
Extension kit for 8 m....................................................................................................................................10
Wheels..........................................................................................................................................................11
LED - Lighting set.......................................................................................................................................12
Hydraulics........................................................................................................................................................13

EC DECLARATION OF CONFORMITY
in accordance with the EU Machinery Directive 2006/42/EC
applicable as from December 29th 2009:
HE-VA ApS
N. A. Christensensvej 34,
DK-7900 Nykøbing Mors
hereby confirms that the following machine has been manufactured in accordance with the Council
Directive 2006/42/EC.
The declaration comprises the following machines:
Top-Strigle with 5 bars
3,0m –4,0m rigid
4,0m –8,0m hydraulic
Nykøbing the 28th february 2011 Villy Christiansen
The undersigned is furthermore authorised to compile technical documentation for the above machine.

Top-Strigle 3,0 –4,0 –5,0 –6,0 –7,0 –8,0 m 5 bars 11-02-2021
1
Back to the table of contents
Delivery Check
Check the Top-Strigle for any damage when it is received at either the dealer and the final customer.
Check that the frame construction has not beeb exposed to impacts. Check the air-pressure in the tires before
operating.
Check the hydraulic hoses for cuts and squeezing damages. Check also the other hydraulic components, are
not damaged during transport.
Machine description
The Top-Strigle is a 5 bar strigle which is suitable for aeration of pasture or spreading out heaps of straw as
well as making seeds from weeds and wasted grain germinate. The machine can only be delivered as tail
mounted option.
The machine can be delivered with two different types of tines:
•12 mm x 440 mm tines for aeration of pasture
•16 mm x 660 mm tines for spreading straw and make undesirable seeds germinate
Standard equipment:
•5 hydraulic adjustable bars
Row spacing:
•With 12 mm long finger tines: 6,0 cm
•With 16 mm long finger tines: 8,3 cm
Distance between bars:
•500 mm
Optional equipment:
•Support wheels 2x2 pcs. of 200/60x14,5”

Top-Strigle 3,0 –4,0 –5,0 –6,0 –7,0 –8,0 m 5 bars 11-02-2021
2
Back to the table of contents
Technical specifications
Working
width
Tine size
Transport
width
Transport-
height
No. of
tines
HP
requirement
Weight in kg
3,00m rigid
12mm
3050
1500
50
85-110
840
16mm
3050
1500
36
95-115
930
4,00m rigid
12mm
4050
1500
66
100-125
1060
16mm
4050
1500
48
110-135
1170
4,00m hydr.
12mm
1500
2100
66
100-125
1480
16mm
1500
2100
48
110-135
1590
5,00m hydr.
12mm
1500
2600
82
120-145
1660
16mm
1500
2600
60
130-155
1780
6,00m hydr.
12mm
1500
3100
100
140-170
1840
16mm
1500
3100
72
155-180
1950
7,00m hydr.
12mm
1500
3600
116
160-195
2020
16mm
1500
3600
84
190-230
2150
8,00m hydr.
12mm
1500
3600
132
175-225
2240
16mm
1500
3600
96
225-275
2390
Tyre pressure
3,8 bar / 55 psi
Oil pressure
min. 150 bar
Hydraulic outlets
2 double acting
Quick couplings, standard
Sterling type E 402
Hydraulic oil: The machine is filled with
Hydro Texaco HD32
Working with the Top-Strigle
There is no standard tine angle recommended. The operator may adjust to achieve the desired results. The
following issues listed must be taken in consideration:
•Actual settings will vary with tine wear
•Ensure frame is leveled horizontal
•Operate with the lift hydraulic in float position
•For best results in stubble operate at 14 - 18 km/h, in pasture 8 - 12 km/h
•A more aggressive tine angle will hold up straw for a longer period, allowing for a more even
distribution of residue
•Breaking down straw is much more effective in dry conditions
•A second pass may be required in extremely heavy straw conditions. Then work the second pass at a
30° - 45° angle to how it was worked the first time
•To prevent tine damage, avoid tight turning

Top-Strigle 3,0 –4,0 –5,0 –6,0 –7,0 –8,0 m 5 bars 11-02-2021
3
Back to the table of contents
Safety around the Top-Strigle
Do not operate the machine, if any people** are at risk in the dangerous area.*
When persons are at risk in the dangerous area (e.g. when doing adjustments, maintenance or connect or
disconnecting), the following points must be met:
•Lower the machine on solid ground.
•Hydraulics must be relieved.
•Tractor must be turned off, and the key removed.
•Driver must be aware of, when operating that there is no persons at risk in the dangerous area.
* Dangerous area: At the machine and underneath it, and in a distance of 4 m from it.
** People at risk: Any person, who is completely or partially in the dangerous area.
Most accidents when operating the machine, transporting and doing maintenance occurs, when avoiding the
most simple safety regulations.
For this reason, it is of highest importance, that any person who is operating the machine, strictly follows the
safety regulations and other instructions, which belongs the machine.
The machine must only be operated, maintained and fixed by persons, who is confidential with and skilled
for this work and is aware of moments of danger, which can occur.
ATTENTION!! Rotating parts and clothes in a loose condition, is a dangerous combination.
IMPORTANT!! It is strictly prohibited for any person to take place on the frame or chassis
of the machine, when it is either operating or the tractor is idling.
Instructions for transport at public roads:
Before transport at public roads, make sure that the attachment of the implement to the tractor, is in
accordance with the local rules and regulations in force (permitted total weight, permitted axel load,
transport width, lights and warning signs).
When driving at public roads, the tines must be folded towards the frame. This will reduce the width
of the machine substantially.
Front axel load:
When the implement is attached and at maximum load, the tractors driving properties must be ensured.
Check that the front axel is sufficiently loaded. The front axel load must be at least 20% of the tractors
weight. Permitted axel load and total weight for the tractor must be respected.
NB! The driving, controlling and braking properties are affected by the attached implement.

Top-Strigle 3,0 –4,0 –5,0 –6,0 –7,0 –8,0 m 5 bars 11-02-2021
4
Back to the table of contents
Safety Instructions, regarding Hydraulic System
•The highest allowable pressure, is 225 bar.
•It is recommended to mark the hydraulic connections between the implement and tractor, to avoid
incorrect operation!
•When checking for hydraulic leeks, suitable safety gear must be used due to danger. (Safety,
goggles, gloves, etc.)
At high pressure, hydraulic oil can penetrate the skin and course serious injuries.
•Before any work at the hydraulic system, the implement must be lowered to solid ground. Pressure
must be relieved, engine stopped, and ignition key removed.
•Check the hydraulic hoses on a regular basis, however, every six months as a minimum due to any
cracks, wear and tear, etc. Replace any defective hoses immediately.
•Hydraulic hoses lasts for no more than 5 years.
New hydraulic hoses must be identical to the manufacturers specifications.

Top-Strigle 3,0 –4,0 –5,0 –6,0 –7,0 –8,0 m 5 bars 11-02-2021
5
Back to the table of contents
Markings on the machine
Several markings are located at your machine, which contains safety regulations and other instructions to
inform about correct operating.
Please read these instructions carefully, and make the driver aware about the markings and safety
regulations in this Operating Instructions. Keep the markings clean and readable. If they are not, they must
be replaced.
Safety and other markings on the machine
Study the Operating Instructions thoroughly before any operation of
the machine and observe all safety instructions.
Plate with number and year of manufacture.
Plate with number and year of manufacture.
Take care that no persons are within the machine’s hazardous area
during the unfolding and folding procedure.

Top-Strigle 3,0 –4,0 –5,0 –6,0 –7,0 –8,0 m 5 bars 11-02-2021
6
Back to the table of contents
Maintenance
After 10 hours of operation, tightening of wheels, bearings and stop rings must be done. If this is not
respected our warranty will lapse.
Maximum torque in Nm. w/lubricated thread
Metric thread
Quality 8.8
Quality 10.9
Quality 12.9
M10x1,5
47
65
79
M12x1,75
81
114
136
M14x2,0
128
181
217
M16x2,0
197
277
333
M18x2,5
275
386
463
M20x2,5
385
541
649
M22x2,5
518
728
874
M24x3,0
665
935
1120
Hub bolts M18x1,5 fine thread
433 Nm
Hub bolts M22x1,5 fine thread
803 Nm
Eventually damages at the paint must be rapaired at least once in the season. This will preserve and
make the machine stay in a good condition for many years.
Disposal
When, after many years of use, the machine is to be regarded as end-of-life, it must be disposed of to a
registered and approved product dealer. This will carry out the statutory discharge and disposal of hydraulic
oil, as well as sorting materials for further processing for recycling.

Top-Strigle 3,0 –4,0 –5,0 –6,0 –7,0 –8,0 m 5 bars 11-02-2021
7
Back to the table of contents
Notes

Top-Strigle 3,0 –4,0 –5,0 –6,0 –7,0 –8,0 m 5 bars 11-02-2021
8
Back to the table of contents
Spareparts list
Right section, 5-bars w/Ø16 mm long finger tine 6.0 - 7,0 - 8,0 m

Top-Strigle 3,0 –4,0 –5,0 –6,0 –7,0 –8,0 m 5 bars 11-02-2021
9
Back to the table of contents
Pos.
Part no.
Description
6m
7m
8m
1
1275219
Left section, welded (not shown)
1
1
1275220
Right section, welded (not shown)
1
1
1275165
Left section, welded (not shown)
1
1
1
1275113
Right section, welded
1
1
2
1275225
Bar, left (not shown)
5
2
1275226
Bar, right (not shown)
5
2
1275126
Bar, left (not shown)
5
5
2
1275164
Bar, right
5
5
3
1275143
Holder for bar
20
20
20
4
1275127
Parallel bar, w/welded fixation for bolts
2
2
2
5
1275125
Parallel bar
2
2
2
6
0236200
Bolt M20 x 110
10
10
10
7
0272310
Faceted washer Ø20 DIN125B
10
10
10
8
0264110
Safety nut M20
10
10
10
9
69430145G
Pin Ø30 x 140 mm
4
4
4
10
630532600
Lock bushing for pin head
6
6
6
11
0235350
Bolt M12 x 35 mm
6
6
6
12
0236360
Bolt M24 x 65 mm 8.8 fzb for adjustment
4
4
4
13
0261425
Nut M24 as locknut
4
4
4
14
1275023
Cylinder 50/30 x 250 mm
2
2
2
15
690136001
Greasenipple M6 straight
4
4
4
16
664004007
Pin Ø25 x 115 mm
2
2
2
17
7355002
U-bolt
4
4
4
18
0261350
Nut M8 black
8
8
8
19
1275235
Plate for scala
1
1
1
20
1275239
Scala
1
1
1
21
0236210
Bolt M20x120 mm
2
2
2
22
0272310
Faceted M20 DIN125B
2
2
2
23
0264110
Safety nut M20
2
2
2
24
633055609
Long finger tine Ø16 x H 655mm
72
84
96
25
633055612
Mounting bracket Ø12
72
84
96
26
0235485
Bolt M12x120 mm 10.9
72
84
96
27
0272270
Faceted washer Ø12 DIN125B fzb
72
84
96
28
0272820
Disc as mounting plate
72
84
96
29
0264070
Safety nut M12 DIN125B fzb
72
84
96
-
-
Regarding Ø12 tine see 4 bar table pos. 12 - 14
-
-
-
30
1275115
Main frame
1
1
1

Top-Strigle 3,0 –4,0 –5,0 –6,0 –7,0 –8,0 m 5 bars 11-02-2021
10
Back to the table of contents
Extension kit for 8 m
Pos.
Part no.
Description
8m
1
1275151
Holder for storage of extension bar, left
1
2
1275152
Holder for storage of extension bar, right
1
3
1275182
Extension bar, left 1
1
4
1275183
Extension bar, left 2
1
5
1275184
Extension bar, left 3
1
6
1275185
Extension bar, left 4
1
7
1275186
Extension bar, left 5
1
8
1275191
Extension bar, right 5
1
9
1275190
Extension bar, right 4
1
10
1275189
Extension bar, right 3
1
11
1275188
Extension bar, right 2
1
12
1275187
Extension bar, right 1
1
13
630980400
Pin Ø19 L100 w/chain and ring pin
10
14
690110101
U-bolt M16 100x100x100
4
15
0272290
Faceted washer Ø16
8
16
0261390
Nut M16
8

Top-Strigle 3,0 –4,0 –5,0 –6,0 –7,0 –8,0 m 5 bars 11-02-2021
11
Back to the table of contents
Wheels
Pos.
Part no.
Description
1
7330056
Console for wheel
1
2
7330047
Steel profile w/hub and axel
1
3
69516125A
Pin Ø16 S355J2
1
4
0377400
Hair-clip Ø4
1
5
0395630
Tire 200/60 –14,5 10 ply
1
6
0395610
Rim 200/60 –14,5 5/94/140 w/protection of valve
1
7
0395271
Hubbolt M16x1,5x50mm 10.9
10
8
0395431
Hub 5-holes
2
0395433
Sealing cassette Ø90/Ø55 –14/17mm
2
0479010
Bearing (conical roller bearing) 30210 (Ø50)
2
0478990
Bearing (conical roller bearing) 30207 (Ø35)
2
0395242
Hub nut M27x1,5mm DIN937
2
9
0395436
Hub cab 78x3 m/gevind
2
10
690141116
Wheel nut M16x1,5 R19
10
11
690110404
U-bolt M18x100x100x100
2
12
0272300
Faceted washer Ø18
4
13
0264100
Safety nut M18
4

Top-Strigle 3,0 –4,0 –5,0 –6,0 –7,0 –8,0 m 5 bars 11-02-2021
12
Back to the table of contents
LED - Lighting set
Note: Check number and measurements of all cables before ordering the spare parts.
Pos.
Part no.
Description
Quantity
1
7357505
Lightbox (L)
1
7357508
Lightbox (R)
1
2
7357504
Rear light
2
3
0264030
Locking nut M5
16
4
7357507
Marking lights (L)
1
7357509
Marking lights (R)
1
5
0234340
Bolt M5x25
4
6
0272240
Facet plate Ø5
8
7
0656240
Reflex, yellow
2
8
0656250
Reflex, white
2
9
692160017
Reflex, red
2
10
0234330
Bolt M6x20
4
11
7357516
Bracket
2
12
0272250
Facetplate Ø8
16
13
0264050
Locking nut M8
8
14
0234750
Bolt M8x20
4
15
690160080
Cable 5 x 1mm² (Inform about lenght by ordering sparepart)
16
7357545
Rutaseal nipple M20 8-12mm Grey RAL7001
2
17
690160070
Plug 7 poles DIN 72 577 –ISO 1724
1
18
7357546
Rubberbushing Nr. 38A Ø10/3 black
1
19
0520492
Junction box 105x105x60
1

Top-Strigle 3,0 –4,0 –5,0 –6,0 –7,0 –8,0 m 5 bars 11-02-2021
13
Back to the table of contents
Hydraulics
7,0 - 8,0 meter 5 bar Top-Strigle

Top-Strigle 3,0 –4,0 –5,0 –6,0 –7,0 –8,0 m 5 bars 11-02-2021
14
Back to the table of contents
Pos.
Part no.
Description
5,0 - 6,0 - 7,0 - 8,0m
1
690200060
Cylinder 70/40 x 500
2
2
1275023
Cylinder 50/30 x 250
2
3
0442350
Ballvalve 3/8”
2
4
690203130
Fitting, adjustable 12 mounted w/O-ring
2
5
690203106
Fitting 90° 12-3/8” BSP
2
6
690203006
Fitting 90° 10-3/8” BSP
6
7
690203015
Samler T10
4
8
0446751
Fitting straight Ø10 x 3/8”
2
9
0444020
Quick coupling 1/2”, male
4
10
0446752
Fitting straight Ø10 x 1/2”
4
11
-
Straps, 2 pcs. green, 2 pcs. blue
4
12
690201033
Hydraulic hose ¼” L = 2500 mm
1
13
690201033
Hydraulic hose ¼” L = 2500 mm
1
14
0454250
Hydraulic hose ¼” L = 1010 mm
1
15
0454250
Hydraulic hose ¼” L = 1010 mm
1
16
0454250
Hydraulic hose ¼” L = 1010 mm
1
17
0454250
Hydraulic hose ¼” L = 1010 mm
1
18
0454211
Hydraulic hose ¼” L = 710 mm
1
19
690201033
Hydraulic hose ¼” L = 2500 mm
1
20
0454645
Hydraulic hose ¼” L = 2300 mm
1
21
0454591
Hydraulic hose ¼” L = 2000 mm
1
22
0454591
Hydraulic hose ¼” L = 2000 mm
1
23
0454211
Hydraulic hose ¼” L = 710 mm
1

The design is subject to modification without notice.