Heat & Glo HE36CLX-S User manual

1
Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/14
SERVICE TECHNICIAN MANUAL
Model: HE36CLX-S, HE36CLXLP-S
- Instructions -
This service technician manual will assist a qualified service
technician in the diagnosis of a problem and the corrective
action to be taken. Contact your dealer to arrange a service
call by a qualified service technician.
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during
installation and service. Sheet metal edges are sharp.
Leave this manual with party responsible for use
and operation.
WARNING! Risk of Injury! Service to this appliance may
ONLY be performed by a qualified service technician.
• DO NOT store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from
a neighbor’s phone. Follow the gas sup-
plier’s instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury, or death.
Installation and service of this appliance should be performed
by a Hearth & Home Technologies factory-trained Energy
Pro technician.
NOTICE! DO NOT discard this manual. Important service
and maintenance instructions included.
Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
Tape measure Framing material
Pliers Hammer
Phillips screwdriver Manometer
Gloves Framing square
Voltmeter Electric drill and bits (1/4 in.)
Safety glasses Flat blade screwdriver
Saw Non-corrosive leak check solution
1/2 - 3/4 in. length, #6 or #8 Self-drilling screws
1/4 NPT barbed hose fitting (for checking gas pressures
at valve)
WARNING
A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with this
appliance and shall be installed.
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.

Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/142
Safety Alert Key:
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Used to address practices not related to personal injury.
Table of Contents
Tools and Supplies Needed. . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1 Maintenance and Service
A. Maintenance Tasks-Qualified Service Technician . . . . . . . 3
B. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . 4
C. Disengage Firebox from Outer Shell . . . . . . . . . . . . . . . . . 5
D. Engage Support Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . 5
E. Appliance Support - Field Construction . . . . . . . . . . . . . . . 6
F. Filter Inspection & Replacement . . . . . . . . . . . . . . . . . . . . 7
G. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2 LED Sequence Troubleshooting
A. LED Sequence Troubleshooting. . . . . . . . . . . . . . . . . . . . . 9
3 Component and Testing Replacement
A. Testing Pressure Switches . . . . . . . . . . . . . . . . . . . . . . . . 12
B. Testing 24V AC Transformer . . . . . . . . . . . . . . . . . . . . . . 12
C. Convection Blower Safety Switch. . . . . . . . . . . . . . . . . . . 13
D. Replacing Convection Blower . . . . . . . . . . . . . . . . . . . . . 13
E. Testing Combustion Blower Performance . . . . . . . . . . . . 14
F. Replacing Combustion Blower Assembly. . . . . . . . . . . . . 14
4 Condensate Removal System
A. Condensate Removal System . . . . . . . . . . . . . . . . . . . . . 16
B. Winterizing Condensate Removal System. . . . . . . . . . . . 16
5 Electrical Information
A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
B. Optional Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
C. Dampers Wiring Requirements . . . . . . . . . . . . . . . . . . . . 18
D. Electrical Service and Repair . . . . . . . . . . . . . . . . . . . . . . 18
E. Equipment Interface Module (EIM). . . . . . . . . . . . . . . . . . 18
F. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 20
6 Decorative Components Installation
A. Refractory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
B. Teco-Sil Placement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
C. Ember Placement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
D. Install the Log Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . 25
7 Service Parts
A. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
B. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31


3
Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/14
A. Maintenance Tasks-Qualified Service
Technician
The following tasks must be performed by a qualified ser-
vice technician.
Gasket Seal and Glass Assembly Inspection
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, drop cloth and a stable
work surface.
• Inspect gasket seal and its condition.
• Inspect fixed glass assembly for scratches and nicks that
can lead to breakage when exposed to heat.
• Confirm there is no damage to glass or glass frame.
Replace as necessary.
• Verify that fixed glass assembly is properly retained and
attachment components are intact and not damaged.
Replace as necessary.
Logs
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves.
• Inspect for damaged or missing logs. Replace as neces-
sary. Refer to log placement instructions in Section 6.
• Verify correct log placement and no flame impingement
causing sooting. Correct as necessary.
Firebox
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, stainless steel cleaner,
mineral spirits, primer and touch-up paint.
• Inspect for paint condition, warped surfaces, corrosion
or perforation.
• It will be normal for surface corrosion to occur on the
firebox interior surface of the condensing appliance.
• Internal surface of firebox can be maintained by using
stainless steel cleaner to remove effects of oxidation.
• Do not use steel wool or sandpaper to remove oxidation
from interior of firebox. This will reduce the corrosion-
resistance of the stainless steel material.
• Factory-painted surfaces can be maintained with primer
and touch up paint.
• Replace firebox if it has been perforated.
Control Compartment
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, vacuum cleaner, dust
cloths
See Section 1.C and 1.D for instructions on how to
disengage the firebox from the appliance outer shell and
engage the support wheels.
• Vacuum and wipe out dust, cobwebs, debris or pet hair.
Use caution when cleaning these areas. Screw tips that
have penetrated the sheet metal are sharp and should
be avoided.
• Remove all foreign objects.
• Verify unobstructed air circulation.
• Verify unobstructed ducts and filter.
• Check for evidence of water/condensate leakage.
Return Air Filter
Frequency: Every Three Months
By: Qualified Service Technician
Tools needed: Protective sleeves, screw driver
Inspect filter and replace as needed. See Section 1.F for
detailed information.
Condensate Drainage System
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, nut driver, screwdriver
See Section 1.C for instructions on disengaging the firebox
from the appliance outer shell and engage the support
wheels.
• Verify all components of condensate removal system
are working properly. Refer to Section 4 for detailed
information.
• Flush system with clean water. See Section 4 for
instructions.
Burner Ignition and Operation
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, vacuum cleaner, whisk
broom, flashlight, voltmeter, indexed drill bit set, and a
manometer.
• Verify burner is properly secured and aligned with pilot
or igniter.
• Clean off burner top, inspect for plugged ports, corrosion
or deterioration. Replace burner if necessary.
• Replace Glowing embers with new dime-size pieces.
DO NOT block ports or obstruct lighting paths. Refer to
Section 6.C for proper ember placement.
• Check for smooth lighting and ignition carryover to all
ports. Verify that there is no ignition delay.
• Inspect for lifting or other flame problems.
• Verify air shutter setting is correct. See appliance
installation manual for required air shutter setting. Verify
air shutter is clear of dust and debris.
1
1 Maintenance and Service

Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/144
B. Frequently Asked Questions
ISSUE SOLUTIONS
Ember lights on/No flame There is a 2-1/2 minute pre-purge after the appliance is turned on before the flame lights. This
is normal for this appliance.
Convection blower does not turn on
when appliance is turned on.
There is a 4-1/2 minute delay between the time the appliance is turned on and the time that
the convection blower will turn on. This is normal for the appliance.
Condensation on the glass This is a result of gas combustion and temperature variations. As the fireplace warms, this
condensation will disappear.
Blue flames This is a result of normal operation and the flames will begin to yellow as the fireplace is al-
lowed to burn for 20 to 40 minutes.
Odor from fireplace
When first operated, this fireplace may release an odor for the first several hours. This is caused
by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may
also be released from finishing materials and adhesives used around the fireplace.
Film on the glass
This is a normal result of the curing process of the paint and logs. Glass should be cleaned
within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing
process. A non-abrasive cleaner such as gas fireplace glass cleaner may be necessary. See
your dealer.
Metallic noise
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the fireplace.
ISSUE CAUSE SOLUTIONS
System does
not turn
on when
in “HEAT”
mode.
A. Indoor tempera-
ture is higher than
heat setting
Increase heat setting to a
temperature higher than indoor
temperature.
B. Wireless
thermostat has lost
connection. “No
Signal” flashing in
upper left corner of
thermostat display.
1. Check Electronic Ignition
Module (EIM) for POWER
light. (Green)
Light on
No light Check breaker. If breaker ok, call qualified
service technician.
2. Verify that the thermostat is
located more than two feet from
the Electronic Ignition Module
(EIM).
3. Refer to RedLINKTM instruc-
tions regarding connections.
C. Check LED
status code. See
Figure 2.1.
Thermostat
screen is
blank.
Check batteries.
Batteries dead. Replace batteries.
Batteries ok. Call qualified service technician.
• Inspect orifice for soot, dirt and corrosion. Verify orifice
size is correct. See Service Parts List for proper orifice
sizing.
• Verify manifold and inlet pressures. Adjust regulator as
required.
• Inspect flame sensing rod for soot, corrosion and
deterioration. Polish with fine steel wool or replace as
required.

5
Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/14
FIREBOX LATCHES
STOWED
SUPPORT WHEEL
NUTS
SUPPORT WHEEL
ASSEMBLY
DEPLOYED
SUPPORT WHEEL
Figure 1.1. Disengage Firebox from Outer Shell
C. Disengage Firebox from Outer Shell
In order to perform certain setup and maintenance tasks,
it will be necessary to partially separate the firebox from
the outer shell of the appliance. Use a Phillips screwdriver
to loosen the 1/4 turn fasteners on the two latches on the
lower front face of the appliance and pull the firebox out
carefully using both hands. See Figure 1.1.
CAUTION! Risk of injury! Avoid pinch points by grasp-
ing only front and side of appliance door when pushing
back into place.
NOTICE! Appliance is heavy. Slide out and in carefully to
avoid scratching floor or hearth.
D. Engage Support Wheels
This appliance is fitted with linear motion slide mecha-
nisms to provide guidance and support of the appliance
as it is separated from the outer shell. These slide mech-
anisms will deflect under the weight of the firebox. This
deflection presents the possibility of the firebox contact-
ing flooring materials as it is transferred in and out of the
outer shell. The appliance is equipped with support wheel
assemblies to carry the load and to reduce the possibility
of damage to flooring.
There is one adjustable support wheel on both the left and
right sides of the firebox to help support the weight of the
firebox when it is being pulled out. Pull appliance out ap-
proximately four inches to access the support wheels. To
utilize the support wheel, loosen the nuts and adjust the
wheel to the desired height. Use care when pulling appli-
ance out to avoid scratching the floor or hearth. Rest the
slide in the slot at the appropriate height and tighten the
nuts. If the firebox will be extended to a point where the
wheel does not touch the surface, an additional means of
support will be needed. See Section 1.E.
WARNING! Risk of injury! Support firebox with support
wheels. Firebox may tip when pulled away from outer shell.
When finished with appliance maintenance task, push the
firebox back to within four inches of closing, adjust the
support wheels to the original stowed position and secure
in place. Engage the 1/4 turn fasteners on the latches on
the lower front face of the appliance, to secure it within the
outer shell. Pull gently on the firebox to verify the firebox
is correctly secured and latched.

Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/146
E. Appliance Support - Field Construction
Circumstances may require that a support be constructed
in the field. The following materials will be necessary to
construct the support.
Tape measure Wood
Nails or Screws Hammer
Screwdriver Safety glasses
Gloves Level
CAUTION! Risk of injury! Avoid pinch points by grasp-
ing only front and side of appliance door when pushing
back into place.
NOTICE! Appliance is heavy. Slide out and in carefully to
avoid scratching floor or hearth.
1. Disengage the appliance from the outer shell by fol-
lowing the instructions in Section 1.C.
2. Slide the appliance out over the raised hearth ap-
proximately one inch.
3. Measure from the floor to the bottom return bend as
shown in Figure 1.3. The constructed support will be
made to rest on the bottom return bend. Push the
appliance back into the outer shell while constructing
the support.
Figure 1.3. Measure from Hearth to Bottom Return Bend
MEASURE TO BOTTOM
OF RETURN BEND
4. Construct the support to a height no shorter than 1/4
inch less than the measurement taken in Step 3. See
Figure 1.4 for a recommended design. In this sce-
nario the width of the support is slightly wider than the
width of the appliance.
BOTTOM
RETURN
BEND
Figure 1.2. Location of Bottom Return Bend
Figure 1.4. Field-Constructed Appliance Support
5. Place the support in position at the desired distance
in front of the appliance.
Note: When fully extended, the bottom return bend is
approximately 27 inches from the outer shell.
6. Disengage the latches and slide the appliance out
and set it on the support so that the bottom return
bend rests on the constructed support.
Figure 1.5. Appliance Resting on Field-Constructed Support
Figure 1.6. Bottom Return Bend Resting on Field-Constructed
Support
BOTTOM
RETURN
BEND

7
Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/14
F. Filter Inspection & Replacement
This appliance requires a filtered return air duct. A slot is
located on the lower left of the appliance for a standard
12 x 24 x 1 filter. See Figure 1.7. The filter may be used
in the slot provided on this appliance or elsewhere in the
ducting system between the intake(s) and the appliance.
If multiple air intake locations exist, each must have its
own filter. Filters are not included with this appliance.
1. To install or replace filter, disengage latch and pull fire-
box out by following the instructions in Section 1.C.
2. Remove the screw that secures the filter door to the
appliance. See Figure 1.7.
3. Remove the filter door, place the filter in the slot so
that the air flow is directed toward the inside of the ap-
pliance.
4. Reattach the filter door.
5. Push firebox back in and latch.
REMOVE SCREW
Figure 1.7. Filter Replacement

Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/148
Figure 1.8. Door Latching Fasteners
G. Fixed Glass Assembly
WARNING! Risk of Asphyxiation! Handle fixed glass
assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.
• DO NOT strike, slam or scratch glass.
• DO NOT operate fireplace with glass removed, cracked,
broken or scratched.
• Replace as a complete assembly.
Removing Fixed Glass Assembly
1. Remove the three 1/4 inch nuts on the bottom of the
glass frame. See Figure 1.8.
2. Use a Phillips screwdriver to turn the 1/4 turn latching
fasteners counterclockwise and pull the firebox out
approximately two inches.
3. Grab the lower portion of the glass assembly and
pivot out and up.
1/4 TURN LATCHING FASTENERS
1/4 INCH NUTS
TOP GLASS FRAME HOOK
RETURN BEND
Figure 1.9. Top Glass Frame Hook
Replacing Fixed Glass Assembly
1. Insert the top glass frame hook on the return bend on
the top side of the firebox. See Figure 1.9.
2. Pivot the bottom of the glass assembly toward the
firebox.
3. Reinstall the three 1/4 inch nuts on the bottom of the
glass frame and tighten.
4. Push the firebox back into the outer shell.
5. Put the 1/4 turn latching fasteners back in place and
turn clockwise to tighten. Pull gently on the firebox to
verify the firebox is correctly secured and latched.

9
Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/14
See Troubleshooting information on following pages.
GREEN LED FLASH SEQUENCE CONTROL STATUS
Short flash once every four seconds IDLE (no call for heat, no fault conditions)
“Heartbeat” alternates bright/dim Call For Heat (no fault conditions)
Two Flash, three second pause Pressure Switch Failed Closed
Three Flash, three second pause Pressure Switch Failed Open
Four Flash, three second pause Limit Switch Open
Five Flash, three second pause Flame Out Of Sequence
Six-One Flash, three second pause Soft Lockout - Failed Trial For Ignition
Six-Two Flash, three second pause Soft Lockout - Recycle Limit - Limit Switch Opened
Six-Three Flash, three second pause Soft Lockout - Recycle Limit - Pressure Switch Opened
Six-Four Flash, three second pause Soft Lockout - Recycle Limit - Flame Lost
Six-Five Flash, three second pause Soft Lockout - Flame out of Sequence Sensed
Seven-One Flash, three second pause Control Board Fault
Seven-Two Flash, three second pause Gas Valve Fault
Seven-Three Flash, three second pause EnviraCOMTM Bus Fault
AMBER LED FLASH SEQUENCE (Flame Sense Indicator)
A amber LED labeled ‘Flame” is provided to indicate flame status. When flame is sensed,
the LED will indicate three flame signal levels:
STATUS
SIGNAL LEVEL
On Solid
LED DISPLAY
Flashing
Off
Flame signal at least 1 micro amp above RUN level Normal
Flame signal between Normal and Flame Lost levels Alert
No Flame Sensed
Flame signal below Flame Lost level
2183-905
Figure 2.1. LED Codes
Figure 2.2. Reflective Label
REFLECTIVE LABEL
The LED flash sequences for the amber and green LED’s
are described in Figure 2.1.
The LED code can be viewed by disengaging the latch and
pulling the firebox out approximately six inches. There is a
reflective label on the upper right side that allows viewing of
the LED’s. See Figure 2.2. For instructions on disengaging
the firebox from the outer shell, see Section 1.C.
A. LED Sequence Troubleshooting
2
2 LED Sequence Troubleshooting

Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/1410
SEQUENCE* STATUS CAUSE SOLUTION
Two flash,
three second
pause.
Exhaust
pressure
switch (red)
failed closed.
A. Vacuum tube
connected prop-
erly. No kinks.
Verify vacuum tube is
connected to switch and
combustion blower.
B. Bad switch,
(continuity is
present).
Replace switch.
Three flash,
three second
pause.
Pressure
switch failed
open.
A. Vacuum
tubes.
1. Verify that vacuum tubes
are connected properly.
B. Wires. 1. Ensure wires are con-
nected to switch.
C. Continuity. 1. Check for continuity on
an unpowered unit. See
Section 3.A.
.4 in. w.c.
Red label With continuity Replace switch.
.4 in. w.c.
Red label No continuity Switch is good.
.35 in. w.c.
Green label With continuity Switch is good.
.35 in. w.c.
Green label No continuity Replace switch.
D. Inducer. 1. Verify that inducer runs
when there is a call for heat.
E. Venting. 1. Verify that vent sys-
tem components are not
blocked or plugged.
F. Condensate. 1. Verify condensate system
is working properly.
Four flash,
three second
pause.
Limit Switch
Open.
A. Wires. 1. Verify wires are con-
nected properly.
B. Temp. Switch. 1. Check temp. switch for
continuity.
Continuity = Good switch.
No continuity = Bad switch. Replace switch.
Five flash,
three second
pause.
Flame out of
sequence.
A. Valve. 1. Check valve wires and
ON/OFF switch.
2. Replace valve.
Six-One
flash, three
second
pause
Failed trial
for ignition.
A. Gas supply. 1. Ensure gas is turned on.
2. Ensure valve switch is
“ON.”
B. Igniter. 1. Verify igniter is wired to
board and igniter.
C. Sensor wire. 1. Verify sensor wire (blue)
is connected.
D. Spark Gap. 1. Ensure spark gap = .16
in.
E. Sensor rod. 1. Ensure flame sense rod
is free of contaminants.
Polish with fine steel wool.
F. Igniter sparks. 1. Turn gas off. Verify
igniter sparks.
Check for burner port obstructions.
Verify proper manifold pressure.
Verify gas ignition.
Verify flame is contacting
flame sense rod.
If yes, replace flame
sense rod.
*Sequence description corresponds to information on label shown in Figure 2.1.

11
Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/14
SEQUENCE* ISSUE CAUSE SOLUTION
Six-two flash,
three second
pause.
Recycle
limit - Temp
limit switch
opened.
A. Convection
blower.
Verify convection blower turns
on.
No.
Check wires.
Check safety switch.
Check capacitor.
Replace blower. See Section
3.D.
Yes.
Check filter.
Verify that at least two ducts
are open at all times.
Verify air intake is free of
obstructions.
Check temp. limit switch.
Six-three
flash, three
second
pause.
Recycle
limit - Pres-
sure switch
opened.
A. Vacuum tubes. 1. Check vacuum tubes.
B. Wires. 1. Ensure wires are connected
to switch.
C. Continuity. 1. Check for continuity on an
unpowered unit. See Section
3.A.
.4 in. w.c.
Red label With continuity Replace switch.
.4 in. w.c.
Red label No continuity Switch is good.
.35 in. w.c.
Green label With continuity Switch is good.
.35 in. w.c.
Green label No continuity Replace switch.
D. Inducer. 1. Verify that inducer runs
when there is a call for heat.
E. Venting. 1. Verify that vent system
components are not blocked or
plugged.
F. Condensate. 1. Verify condensate system is
working properly.
Six-four
flash, three
second
pause.
Recycle limit
- Flame lost.
A. Flame sense rod. 1. Check wires.
2. Clean rod.
3. Replace rod.
B. Venting. 1. Verify that vent system
components are not blocked or
plugged.
C. Inducer. 1. Verify inducer is performing
correctly.
Connect manometer to vacuum switch port
on inducer. Verify a minimum of 1.00 in. w.c.
D. Condensate
system.
1. Verify condensate system is
working properly.
Seven-one
flash, three
second
pause.
Control
Board fault.
A. Check wiring. 1. Verify fuse is operational.
B. Replace control
board.
Six-five flash,
three second
pause.
Flame out
of sequence
sensed.
A. Control board. 1. Verify fuse is operational.
2. Verify wiring.
3. Replace control board.
*Sequence description corresponds to information on label shown in Figure 2.1.

Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/1412
A. Testing Pressure Switches
WARNING! Risk of Shock! Disconnect power to appli-
ance prior to beginning this task.
1. Turn off gas supply to valve. Red gas shutoff knob is
located on ball valve.
2. Disconnect electrical supply to the appliance.
3. Remove decorative front.
4. Disengage the appliance from the outer shell by fol-
lowing the instructions in Section 1.C. Slide appliance
out and engage support wheels or use field-construct-
ed support.
5. Set the multimeter to “CONTINUITY” setting.
6. Identify the Exhaust pressure switch by locating the
red label and 0.4 inches w.c. specification on that la-
bel. See Figure 3.1.
7. Place the test leads of the meter to the terminals on
the switch. If continuity is present, the switch is not
functioning correctly and should be replaced. If NO
continuity is present, the switch tests good and is func-
tioning correctly.
8. Identify the intake pressure switch by locating the
green label and 0.35 inches w.c. specification on that
label. See Figure 3.2.
9. Place the test leads of the meter to terminal 1 (c.) and
3 (n.c.). If continuity is present, the switch tests good
and is functioning correctly. If NO continuity is present,
the switch is not functioning correctly and should be
replaced.
Figure 3.1. Test Exhaust Pressure Switch
RED LABEL
RED LABEL
Figure 3.2. Test Intake Pressure Switch
GREEN LABEL
GREEN LABEL
B. Testing 24V AC Transformer
1. Turn off gas supply to valve. Red gas shutoff knob is
located on ball valve.
2. Remove decorative front from appliance.
3. Disengage the appliance from the outer shell by fol-
lowing the instructions in Section 1.C. Slide appliance
out and engage support wheels or use field-construct-
ed support.
4. Set the multimeter to VOLTS AC.
5. Place the leads on terminals 1 and 3. The display should
read approximately 108-132VAC. See Figure 3.3.
6. Place the leads on terminals 4 and 5. The display
should read “24V.” See Figure 3.4.
If the readings are different than noted above, replace the
transformer.
Figure 3.3. Test Terminals 1 and 3
Figure 3.4. Test Terminals 4 and 5
3
3 Component and Testing Replacement

13
Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/14
C. Convection Blower Safety Switch
The convection blower is wired through a safety switch so
the convection blower will not operate when the firebox is
disengaged from the outer wrap and/or being serviced.
See Figure 3.5.
WARNING! Risk of Injury! DO NOT bypass the safety
switch. Fan blades will cause injury.
D. Replacing Convection Blower
1. Turn off gas supply to valve. Red gas shutoff knob is
located on ball valve.
2. Disconnect electrical supply to the appliance.
3. Remove decorative front.
4. Disengage the appliance from the outer shell by fol-
lowing the instructions in Section 1.C and 1.D. Slide
appliance out and engage support wheels or use field-
constructed support.
5. Disconnect blower wires from capacitor.
CAUTION! Risk of shock! Capacitor has stored energy.
6. Remove blower assembly by removing eight 3/8 in.
bolts. See Figure 3.6.
Figure 3.6. Remove Blower Assembly
Figure 3.7. Grommet and Wires
7. Remove grommet and feed wires through hole. See
Figure 3.7.
8. Remove blower assembly through the top opening of
the appliance. See Figure 3.8.
9. Remove four Phillips head screws. See Figure 3.9.
Figure 3.8. Remove Blower Assembly
Figure 3.9. Remove Screws
CAPACITOR SAFETY
SWITCH
WARNING! Risk of Shock! Capacitor contains stored
voltage. Discharge capacitor before servicing.
Figure 3.5. Capacitor and Safety Switch

Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/1414
E. Testing Combustion Blower Performance
F. Replacing Combustion Blower Assembly
1. Turn off gas supply to valve. Red gas shutoff knob is
located on ball valve.
2. Remove decorative front.
3. Disengage the appliance from the outer shell by fol-
lowing the instructions in Sections 1.C and 1.D. Slide
appliance out and engage support wheels or use field-
constructed support.
4. Disconnect the vacuum tube from the exhaust pres-
sure switch. The exhaust pressure switch has the red
label noting 0.4 in. w.c. See Figure 3.11.
Figure 3.11. Disconnect Vacuum Tube
5. Connect tube to manometer. See Figure 3.12.
6. Turn on combustion blower.
7. Check the manometer reading. It should be a mini-
mum of 0.75 inches w.c. See Figure 3.12.
Figure 3.12. Manometer Reading.
VACUUM TUBE
VACUUM TUBE
READING
READING
1. Turn off gas supply to valve. Red gas shutoff knob is
located on ball valve.
2. Disconnect electrical supply to the appliance.
3. Remove decorative front.
4. Disengage the appliance from the outer shell by fol-
lowing the instructions in Sections 1.C and 1.D. Slide
appliance out and engage support wheels or use field-
constructed support.
5. Disconnect the blower power wires and green/yellow
ground wire. See Figure 3.13.
Figure 3.13. Disconnect Blower Wires
6. Loosen hose clamp on blower and remove flex hose.
Figure 3.14. Loosen Hose Clamp
10. Turn assembly over and remove four screws to re-
lease the blower from the mounting bracket. See
Figure 3.10.
Figure 3.10. Remove Blower from Mounting Bracket
GROUND
GROUND
WIRE
WIRE
DISCONNECT POWER
DISCONNECT POWER
WIRES FROM QUICK
WIRES FROM QUICK
CONNECT TERMINAL
CONNECT TERMINAL

15
Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/14
7. Remove blower assembly bracket from the two screws
on the appliance. See Figure 3.15.
Figure 3.15. Remove Blower Assembly Bracket
8. Disconnect heat exchanger nut from blower assembly.
See Figure 3.16.
Figure 3.16. Disconnect Heat Exchanger
9. Remove four 3/8 in. mounting bolts. See Figure 3.17.
Figure 3.17. Remove Mounting Bolts
10. Disconnect the drain line from the blower assembly
and remove the assembly from the appliance. Con-
densate will be present in the blower assembly, han-
dle carefully.
CAUTION! Risk of Injury!
.• Remove any excess condensate or spillage
immediately to avoid slips and falls.
• Do not allow condensate to come into contact with
mouth or eyes.
11. Install new combustion blower assembly by perform-
ing Steps 9 through 5 in reverse. When reconnecting
heat exchanger, tighten nut to hand-tight, plus an ad-
ditional 1/4 turn. See Figure 3.16.
12. Reconnect the drainline to the blower assembly.

Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/1416
A. Condensate Removal System
This appliance will create condensate. The condensate
must be piped directly to a drain via approved piping or
with a condensate pump. The condensate drain is located
on the lower right side of the appliance. See Figure 4.1.
Drain pipe and fittings must conform to ANSI standards
and ASTM D1785, D2466 or D2846. CPVC or PVC ce-
ment must conform to ASTM D2564 or F493. Primer
must conform to ASTM F656. In Canada, use CSA or
ULC certified schedule 40 CPVC or ULC certified sched-
ule 40 CPVC or PVC drain pipe, fittings and cement.
The condensate drainage system and pump use gravity
and should be located lower than the discharge location
on the appliance. The condensate must be drained
efficiently in order for the appliance to operate at peak
performance.
CAUTION! Risk of Injury!
.• Remove any excess condensate or spillage
immediately to avoid slips and falls.
• Do not allow condensate to come into contact with
mouth or eyes.
If a condensate pump will be used with the appliance, it is
recommended that a pump with a safety switch be used.
In the event of a pump failure, the safety switch will not
allow the appliance to operate. The pump should be ap-
proved for condensate producing appliances and have an
overflow switch.
4-1/2 IN.
CONDENSATE
DRAIN 1/2 IN.
PVC FITTING
CONDENSATE
PUMP ACCESS
PANEL
Figure 4.1.
CAUTION! Risk of Injury!
• Condensate pump should be located as close to
the appliance as possible for efficient removal of
condensate.
Furnace condensate is mildly acidic and may be corrosive.
A pH neutralizing filter may be needed. Check with local
authorities if this type of filter is required.
An access panel is located on the right side of the appli-
ance. This panel is for servicing the condensate system
after appliance installation. The removal of five screws is
required to remove the panel.
B. Winterizing Condensate Removal System
NOTICE: The appliance must be winterized if the appliance
is subjected to ambient temperatures of 32ºF (0ºC) or lower.
Some water will accumulate in the heat exchanger as a
result of the heat transfer process. To winterize your ap-
pliance:
1. Turn off gas supply to valve. Red gas shutoff knob is
located on ball valve.
2. Disconnect electrical supply to the appliance.
3. Disengage firebox from outer shell approximately 12
inches. Adjust support wheels and/or provide addition-
al support if necessary. See Section 1.C and 1.D
4. Remove upper inducer tube from inducer housing.
See Figure 4.2.
4
4 Condensate Removal System
APPLIANCE FRONT
TUBE
Figure 4.2. Upper Inducer Housing Tube - Connected to Inducer

17
Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/14
APPLIANCE FRONT
Figure 4.3. Upper Inducer Housing Tube Connected to Field-
Supplied Funnel
5. Insert 3/8 inch (ID) field-supplied funnel into tube. See
Figure 4.3.
6. Pour one quart propylene glycol (swimming pool/RV
antifreeze) into funnel.
NOTICE: DO NOT use any antifreeze other than propylene
glycol. Damage to plastic components may occur.
Propylene glycol should run through inducer housing,
fill condensate trap and overflow into condensate drain.
Propylene glycol remains in condensate system. It does
not need to be removed before appliance startup.
7. Remove funnel and reconnect upper inducer tube to
the housing.
8. Disengage support wheels, return firebox to closed
position and engage latch. See Section 1.C.
9. Reconnect electrical supply.
10. Turn on gas supply at valve.

Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/1418
B. Optional Components
Wiring for optional components should be done now to
avoid reconstruction. Follow manufacturer’s instructions
that accompany those components.
Examples of optional components:
• Condensate Pump
• Heat Duct Dampers
A. Wiring Requirements
NOTICE: This appliance must be electrically wired
and grounded in accordance with local codes or, in the
absence of local codes, with National Electric Code
ANSI/NFPA 70-latest edition or the Canadian Electric
Code CSA C22.1.
NOTICE: Hearth & Home Technologies recommends
that this appliance be wired on its own circuit with its own
circuit breaker.
• Wire the appliance junction box to 110-120 VAC.
• A 110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in
compliance with the applicable electrical codes, when
it is installed in locations such as in bathrooms or near
sinks.
• Low voltage and 110-120 VAC voltage cannot be shared
within the same wall box.
WARNING! Risk of Shock or Explosion! DO NOT wire
110V to the valve or to the Equipment Interface Module.
Incorrect wiring will damage controls.
WARNING! Risk of Shock! Keep electrical wires away
from condensate drainage system.
5
5 Electrical Information
D. Electrical Service and Repair
WARNING! Risk of Shock! Label all wires prior to dis-
connection when servicing controls. Wiring errors can
cause improper and dangerous operation. Verify proper
operation after servicing.
WARNING! Risk of Shock! Replace damaged wire with
type 105º C rated wire. Wire must have high temperature
insulation.
E. Equipment Interface Module (EIM)
The Equipment Interface Module (EIM) is used for com-
munication to take place between the appliance and the
wireless thermostat. The EIM can be installed in a remote
area, but will need to be accessible after installation and
finishing of the appliance are complete. The appliance is
supplied with 25 feet of low voltage wire that will be used
to wire the EIM to the appliance. See Figure 5.1 and
5.2 for wiring. Refer to the manufacturer’s instructions
included with the EIM for further operating instructions.
WIRE COLOR MODULE LOCATION
Blue C
Red R
White W
Yellow Y
Green G
Figure 5.1. EIM Wiring
WARNING! Risk of Shock! DO NOT wire 110V to the
Equipment Interface Module. Incorrect wiring will dam-
age EIM.
Wire the EIM as shown in Figure 5.1.
WARNING! Risk of Shock! Label all wires prior to dis-
connection when servicing controls. Wiring errors can
cause improper and dangerous operation. Verify proper
operation after servicing.
WARNING! Risk of Shock! Disconnect 110-120 VAC
power supply before installing EIM.
NOTICE: The wireless thermostat must be located no less
than two feet and no more than 80 feet from the Equipment
Interface Module.
C. Dampers Wiring Requirements
The appliance is supplied with two (eight foot) lengths of
low voltage wire. The control module supplies 24V AC
to these wires. A switch must be installed to operate any
power dampers. The switch should be located between
the yellow and red wires. See Figure 5.2. The power
relay on the control module is activated or deactivated by
switching these wires. The control switch will not operate
the dampers.

19
Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/14
Figure 5.2. Appliance Wiring Diagram
TERMINALS
Pin # Thermostat Function
1 D (Yellow) Toggle dampers on/off
2 G (Green) Call for continuous low speed fan
3 W (White) Call for heat from thermostat
4 R/2 (Red) 24 VAC hot for thermostat
5 C/3 (Blue) 24VAC system common
9-PIN
Pin # Function
1 Not used
2
Gas valve 24 VAC common – Must be wired
to appliance chassis for proper flame sense
operation.
3Limit switch input (Common with pin 6)
4Main gas valve output
5Pressure switch input
6Pressure switch output (common with pin 3)
7Flame sense output
8Limit switch output
9Flame sense/chassis ground (24VAC common)
DAMPERS
Pin # Function
D1 Damper 1 power
D_IN 24 VAC supply
D2 Damper 2 power
SPARK
ROD
IGNITER
EXHAUST
PRESSURE
SWITCH
LIMIT
SWITCH
GAS VALVE
FLAME
ROD
DAMPER
POWER
SUPPLY
ROOM
DAMPER
ROOM DAMPER
CIRCULATING
FAN BLOWER
FAN CONT
NEUTRALS
24VAC COM
3A FUSE
3C
R
W
G
Y
TO EQUIPMENT INTERFACE
MODULE
ON
FAN
DELAY
XFMR L1 TND HUM
L2 L1 (HOT)
TO 120V, 60 Hz POWER SUPPLY
COMMON
24VAC
INDUCER
JUNCTION BOX
FOR OPTIONAL ELECTRONIC DAMPERS
DAMPERS
9 PIN
INTAKE
PRESSURE
SWITCH
MOTOR START
CAPACITOR SAFETY
SWITCH
SAFETY
SWITCH
SWITCH FOR
OPTIONAL DAMPERS
LED MODULE
LED(5)

Heat & Glo • HE36CLX-S Service Technician Manual • 2183-904 Rev. H • 10/1420
Figure 5.3. Junction Box Detail
NOTICE:
DO NOT
wire 110-
120 VAC to
Equipment
Interface
Module.
F. Junction Box Installation
To wire the junction box from the INSIDE of the appliance:
• Disengage the latch and pull the firebox out. Refer to
Section 1.C and 1.D for instructions.
• Remove the screw attaching the junction box/receptacle
to the outer shell, rotate the junction box inward to dis-
engage it from the outer shell.
• Pull the electrical wires from outside the appliance through
the opening into the valve compartment and secure wires
with a Romex connector.
• Make all necessary wire connections to the junction box/
receptacle and reattach the junction box/receptacle to
the outer shell.
NOTICE: Hearth & Home Technologies recommends
that this appliance be wired on its own circuit with its own
circuit breaker.
Figure 5.4.
Figure 5.5. Power Cord from Wire Harness Plugged into
Junction Box
This appliance is equipped with an exhaust safety switch
that will shut down the appliance in the event of an exhaust
hose disconnection. See Figure 5.3. The exhaust safety
switch is wired to the supplied junction box to the “FAN”
terminals. See Figure 5.4. The power cord from the wire
harness is then plugged into the “FAN” slot on the supplied
junction box. See Figure 5.5.
EXHAUST
SAFETY
SWITCH
JUNCTION
BOX POWER CORD
FROM WIRE
HARNESS