aerauliqa QR350ABP User manual

1
G
Read this manual carefully before using the product and keep it in a safe
place for reference as necessary.
This product was constructed up to standard and in compliance with egulations
relating to electrical equipment and must be installed by technically qualified
personnel.
The manufacturer assumes no responsibility for damage to persons or
property resulting from failure to observe the instructions contained in this
manual.
1 Index 1
2 Precautions 2
3 Product information 2
3.1 General 2
3.2 Dimensions and Weight 3
3.3 Connections 3
3.4 Space required 4
3.5 Rating label 4
4 Transport and Storage 4
5 Installation 4
5.1 Unpacking 4
5.2 Where/how to install 4
5.3 Installation 5
5.4 Electric Connections 7
6 Commissioning 8
6.1 Setting Fan speed 8
6.2 Before Starting the System 9
7 Operation 10
7.1 User Menu on CTRL-DSP 11
7.2 Installer Menu on CTRL-DSP 13
7.3 Additional functionalities 16
8 Maintenance and service 17
8.1 Components list 17
8.2 Description of Components 17
8.3 Maintenance 18
8.4 Service 19
8.5 Trouble shooting 20
9 Disposal and recycling 21
1 INDEX
Installation Manual (installer & user)
QR350ABP - Heat Recovery Ventilation Unit

2
2 PRECAUTIONS
WARNING
Make sure that the mains supply to the unit is disconnected before performing any installation, service, maintenance or
electrical work!
WARNING
The installation and service of the unit and complete ventilation system must be performed by an authorized installer and in
accordance with local rules and regulations.
TRANSPORT AND STORAGE
•Donotleavethedeviceexposedtoatmosphericagents(rain,sun,snow,etc.).
•Ductconnections/ductendsmustbecoveredduringstorageandinstallation
INSTALLATION
•Afterremovingtheproductfromitspackaging,verifyitsconditions.Donotleavepackagingwithinthereachofchildrenor
people with disabilities.
•Bewareofsharpedges.Useprotectivegloves.
•Thedeviceshouldnotbeusedasanactivatorforwaterheaters,stoves,etc.,norshoulditdischargeintohotair/fumeventducts
deriving from any type of combustion unit or tumble dryer. It must expel air outside via its own special duct.
•Iftheenvironmentinwhichtheproductisinstalledalsohousesafuel-operatingdevice(waterheater,methanestoveetc.,that
isnota“sealedchamber”type),itisessentialtoensureadequateairintake,toensuregoodcombustionandproperequipment
operation.
•Theelectricalsystemtowhichthedeviceisconnectedmustcomplywithlocalregulations.
•Beforeconnectingtheproducttothepowersupplyorthepoweroutlet,ensurethat:
 -thedataplate(voltageandfrequency)correspondtothoseoftheelectricalmains
- the electrical power supply/socket is adequate for maximum device power.
•Forinstallationanomnipolarswitchshouldbeincorporatedinthexedwiring,inaccordancewiththewiringrules,toprovide
afulldisconnectionunderovervoltagecategoryIIIconditions(contactopeningdistanceequaltoorgreaterthan3mm).
USE
•Thedeviceshouldnotbeusedforapplicationsotherthanthosespeciedinthismanual.
•Thisappliancecanbeusedbychildrenagedfrom8yearsandaboveandpersonswithreducedphysical,sensoryormental
capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
•Donottouchtheappliancewithwetordamphands/feet.
•The device is designed to extract clean air only, i.e. without grease, soot, chemical or corrosive agents, or ammable or
explosive mixtures.
•Donotusetheproductinthepresenceofinammablevapours,suchasalcohol,insecticides,gasoline,etc.
•The system should operate continuously, and only be stopped for maintenance/service.
•Donotobstructductsorgrillestoensureoptimumairpassage.
•Donotimmersethedeviceoritspartsinwaterorotherliquids.
•Operatingtemperature:0°Cupto+40°C.
SERVICE
•Althoughthemainssupplytotheunithasbeendisconnectedthereisstillriskforinjuryduetorotatingpartsthathavenotcome
to a complete standstill.
•Bewareofsharpedges.Useprotectivegloves.
•Useoriginalsparepartsonlyforrepairs.
3 PRODUCT INFORMATION
3.1 General
This is the Installation Manual of QR350ABP heat recovery ventilation unit.
This manual consists of basic information and recommendations concerning installation, commissioning, use and service
operations to ensure a proper fail-free operation of the unit.
The key to proper, safe and smooth operation of the unit is to read this manual thoroughly, use the unit according to given
guidelines and follow all safety requirements.
The QR350ABP is supplied with its CTRL-DSP remote multifunction control panel as standard. The package also includes 2
condensation elbows and 2 plugs for the water drainage.
WARNING
If any abnormality in operation is detected, disconnect the device from the mains supply and contact a qualified technician
immediately.

3
A
BD
C
Weight Kg
23
3.2 Dimensions (mm) and Weight
3.3 Connections
Fig. 3.a Connections in LEFT orientation
Intake air from outside
Exhaust air to outside
Supply air to inside
Extract air from inside
Winter condensation drainage
Summer condensation drainage
A
B
D
C
F
E
LEFT Connections from and to outside are set on the left side of the unit front view DEFAULT
RIGHT Connections from and to outside are set on the right side of the unit front view
The factory setting is LEFT.
E
F
A
B
C
D

4
3.5 Rating label
Fig.3.c Rating label
3.4 Space required
Makesurethatenoughspaceisleftaroundtheunittoalloweasymaintenance(accesstolters,terminalboxandremovalofthe
sideandfrontinspectionpanels).
TosettheRIGHTorientationofthemachine:
•ModifytheorientationontheCTRL-DSP(point7.2-Installermenu:3MachineOrientation).
•Replacetheductingconnectionlabelonthetopofthecasingandthewaterdrainagelabelonthebottomofthecasingwith
those supplied with this installation manual.
Fig. 3.b Connections in RIGHT orientation
Intake air from outside
Exhaust air to outside
Supply air to inside
Extract air from inside
Winter condensation drainage
Summer condensation drainage
A
B
D
C
F
E
4 TRANSPORT AND STORAGE
The appliance is delivered in one carton box.
The appliance should be stored and transported in such a way that it is protected against physical damage that can harm spigots,
casing, display etc.
It should be covered so that dust, rain and snow cannot enter and damage the unit and its components.
5 INSTALLATION
This section describes how to install the unit correctly.
The unit must be installed according to these instructions.
5.1 Unpacking
Verifythattheunit(andeventualaccessories)deliveredisaccordingtoorderbeforestartingtheinstallation.Anydiscrepancies
from the ordered equipment must be reported to the supplier.
5.2 Where/how to install
•All QR units are meant for indoor installation in a heated space.
•Mounttheunitonflatsurface(wall).
•The unit must always be installed vertically.
•It’s important that the unit is completely leveled before it is put into operation.
•Placetheunitpreferablyinaseparateroom(e.g.storage,laundryroomorsimilar).
WARNING
Make sure that specific warnings and cautions in Chapter 2 “Precautions” are carefully read, understood and applied!
WARNING
Make sure that specific warnings and cautions in Chapter 2 “Precautions” are carefully read, understood and applied!
F
E
AB
CD

5
5.3 Installation
The unit must be installed in the following position.
It is important that the unit is vertical in order for the condensation drainage to work properly.
•When choosing the location it should be kept in mind that the unit requires maintenance regularly and that the inspection doors
should be easily accessible.
•Leavefreespaceforopeningtheremovablepanelsandforremovalofthemaincomponents(see3.4).
•The outdoor air grilles if possible be put in the northern or eastern side of the building and away from other exhaust outlets like
kitchen fan exhausts or laundry room outlets.
Fig. 5.a
517 mm
Fig. 5.b
Fig. 5.c Fig. 5.d
Fig. 5.fFig. 5.e
SPIRIT LEVEL
H=min. 60mm
Fig. 5.g

6
5.a Preparethesurfacewheretheunitistobemounted.Makesurethatthesurfaceisat,leveledandthatitsupportstheweight
of the unit. Perform the installation in accordance with local rules and regulations.
5.b Drill the holes in the wall.
5.d.eHangtheunittothewallbymeansofthexingbracketsandscrewsafely(screwsandwallplugsnotsupplied).
5.f Make sure that the unit is at spirit level.
5.g Connectthesuppliedcondensationelbow(s)tothedrainagehole(s)intheopeningatthebottomoftheunit:incaseclose
andsealthenon-usedholewiththe2suppliedplugs(oneeachsideofthehole).Makesureofwaterandairtightnessofall
connections.ItisnecessarytouseaU-bend(orsimilar)inthecondensationdrainagepipe.Thewaterdrainageconnections
can be made either through the holes at the bottom side of the casing or through the opening at the rear side of the casing.
5.h Connect the unit to the duct system. Make sure that all necessary accessories are used to create a functional ventilation
solution.
5.i Connect the unit electrically according to point 5.4. Check that it starts up correctly.
Fig. 5.h Fig. 5.i
Ø125mm Ø125mm

7
5.4 Electric Connections
The unit must be earthed.
The QR350ABP is wired internally from factory.
ToconnectthetheCTRL-DSPtothemotherboardusea4poletwisted-paircable:maxlength30m.
Figures below show the wiring diagram.
WARNING
Make sure that the mains supply to the unit is disconnected before performing any installation, service, maintenance or
electrical work!
WARNING
The installation and service of the unit and complete ventilation system must be performed by an authorized installer and in
accordance with local rules and regulations.
SLAVE input
1-10V
J2jumperforSLAVEmode
AC power supply
Heat output
(max250Vac5A)
Dehumidifier output
(max250Vac5A)
Boost momentary
switch(BST)
IAQ input
(AirQuality
i.e. SEN-CO2)
HY input
(i.e.SEN-HY)
CTRL-DSP
Inputs/commands
N°1ACsupplyconnector
N°3on/offinputs(volt-freecontacts),twoforambientsensors(namedHY,IAQ)andoneforboostmomentaryswitch(named
BST).
N°11-10Vanaloginput(namedSLAVE).
N°1jumperforSLAVEMODEselection.
N°14-poleconnectorforCTRL-DSP(RS485plus12Vdcsupply).
Outputs
N°1on/offoutputforpre-heating/post-heating(relaycontact–250Vac5A).
N°1on/offoutputfordehumidication(relaycontact–250Vac5A).
Fig. 5.l Electrical connections on the motherboard fitted in the terminal box.
+12V
A B GND
AB1
2
V
G
N
D

8
T R. H. T R. H. ᶯH2OᶯH2OᶯH2OᶯH2OᶯH2OᶯH2O
°C % °C % % kg/h % kg/h % kg/h % kg/h % kg/h % kg/h
-18 60 20 30 95,3 0,16 92,2 0,29 89,0 0,41 85,0 0,51 81,5 0,58 78,3 0,63
-18 70 20 40 96,0 0,22 92,6 0,42 90,0 0,61 86,8 0,78 83,3 0,88 80,1 0,96
-18 80 20 50 96,8 0,28 94,0 0,55 90,6 0,79 88,0 1,02 84,5 1,16 81,3 1,26
-10 60 20 30 95,1 0,10 91,3 0,18 87,6 0,24 83,6 0,29 80,1 0,32 76,9 0,35
-10 70 20 40 96,1 0,16 92,5 0,30 89,6 0,42 87,1 0,53 83,6 0,60 80,4 0,65
-10 80 20 50 96,8 0,21 93,6 0,41 91,2 0,59 88,1 0,76 84,6 0,86 81,4 0,94
0 50 20 30 94,6 0,01 88,8 0 84,6 0 80,1 0 76,6 0 73,4 0
0 60 20 40 95,3 0,06 90,4 0,10 86,6 0,13 83,4 0,13 79,9 0,15 76,7 0,16
0 70 20 50 95,8 0,11 92,8 0,20 89,5 0,28 86,7 0,34 83,2 0,38 80,0 0,42
10 50 20 40 94,0 0 88,8 0 84,3 0 80,3 0 76,8 0 73,6 0
10 60 20 50 93,9 0 88,9 0 84,4 0 81,2 0 77,7 0 74,5 0
10 70 20 60 94,8 0,02 90,3 0,03 85,1 0,03 80,9 0,01 77,4 0,01 74,2 0,01
35 60 26 50 94,4 0 88,8 0 84,4 0 82,0 0 78,5 0 75,3 0
35 70 26 55 95,7 0,04 92,2 0,08 88,9 0,10 85,4 0,11 81,9 0,12 78,7 0,13
35 80 26 60 97,4 0,09 95,0 0,18 93,1 0,26 91,6 0,33 88,1 0,37 84,9 0,41
40 60 26 50 96,4 0,08 92,6 0,15 89,9 0,19 85,7 0,23 82,2 0,26 79,0 0,28
40 70 26 55 97,5 0,14 94,9 0,27 92,6 0,39 91,0 0,50 87,5 0,56 84,3 0,61
40 80 26 60 98,5 0,20 97,2 0,38 95,4 0,57 93,3 0,73 89,8 0,83 86,6 0,90
300 m³/h250 m³/hESTERNO INTERNO 50 m³/h 100 m³/h 150 m³/h 200 m³/h
6 COMMISSIONING
6.1 Setting Fan speed
Thespeedoftheunitcanbeadjustedduringinstallationaccordingtorequiredventilationrate.
Figure 6.a belowshowsperformancecurves(forsupplyairandextractair)atdifferentsettingsofthe0-10Vsignaltothemotors.
Consumption refers to the 2 motors.
Table 6.b indicates the efficiency of the heat exchanger and of the condensation produced in different climatic conditions, to help
the installer or the designer of the ventilation system to decide if to connect one or both condensation drainages.
High production of condensation is the direct consequence of a high efficiency level as well as of the humidity rate.
Table 6.c indicates the sound level at the different speed.
Fig. 6.aIntakecurveaccordingtoReg.1253/2014(ErP).
Static Pressure - Pa
Airow-m3/h
EXTERNAL INTERNAL
Table 6.b Thermal efficiency of the heat exchanger and average production of condensation water. Data supplied by the manufacturer of the heat exchanger.
0
50
100
150
200
250
300
350
400
450
500
550
600
0 50 100 150 200 250 300 350
I
III IV VVI
II
A
B
C
D
E
F
G
Curve Speed
%
W
max
m3/h
max
A(min) 20 8 43
B 35 24 103
C 50 70 185
D 60 98 215
E 67 155 263
F 85 275 330
G(max) 100 325 346
Working point W m3/h SPI (W/m3/h) ɳt %(1)
I 13,7 54 0,2535 89
II 20,1 76 0,2664 89
III 28,9 97 0,2973 88
IV 42,2 119 0,3550 87
V 58,9 140 0,4196 86
VI 68,3 153 0,4464 86
(1)
Thermal efficiency of the unit.

9
Table 6.c Sound level
Preliminary data.
dBA figures are average spherical free-field, for comparitive use only.
6.2 Before Starting the System
Whentheinstallationisnished,checkthat:
•Filtersaremountedcorrectly
•Theunitisinstalledinaccordancewiththeinstructions
•Theunitiscorrectlywired
•Eventualoutdoorandexhaustairdampersandsilencersareinstalledandthattheductsystemiscorrectlyconnectedtotheunit
•Allductsaresufcientlyinsulatedandinstalledaccordingtolocalrulesandregulations
•Outdoorairintakeispositionedwithsufcientdistancetopollutionsources(kitchenventilatorexhaust,centralvacuumsystem
exhaustorsimilar)
•Theunitiscorrectlysetandcommissioned.
100%
Lw dB - SOUND POWER OCTAVE BAND Lp dB(A)
63 125 250 500 1 K 2 K 4 K 8K Tot @3m
Intake 83 65 70 73 62 58 53 47 84 51
Supply 81 65 65 66 57 51 42 33 81 45
Extract 80 63 66 68 60 54 45 34 78 47
Exhaust 78 65 70 71 62 59 53 45 80 50
Breakout 81 69 67 69 62 56 48 36 82 48
80%
Lw dB - SOUND POWER OCTAVE BAND Lp dB(A)
63 125 250 500 1 K 2 K 4 K 8K Tot @3m
Intake 73 61 67 69 59 56 50 43 75 47
Supply 72 61 63 65 56 50 41 31 74 43
Extract 73 60 63 65 57 51 42 31 74 44
Exhaust 73 61 66 67 58 55 49 41 75 46
Breakout 71 64 62 67 59 53 45 33 74 45
60%
Lw dB - SOUND POWER OCTAVE BAND Lp dB(A)
63 125 250 500 1 K 2 K 4 K 8K Tot @3m
Intake 65 61 68 67 58 56 49 41 72 46
Supply 63 59 63 64 55 49 40 29 69 42
Extract 64 59 63 63 56 51 41 30 69 42
Exhaust 64 60 66 67 57 54 48 41 71 45
Breakout 59 64 63 65 57 51 43 31 70 44
40%
Lw dB - SOUND POWER OCTAVE BAND Lp dB(A)
63 125 250 500 1 K 2 K 4 K 8K Tot @3m
Intake 55 55 67 55 49 47 40 31 68 39
Supply 53 53 62 52 47 41 32 22 63 35
Extract 58 52 60 51 47 42 32 22 63 34
Exhaust 55 54 66 55 49 47 40 31 67 39
Breakout 54 53 59 52 48 43 33 23 62 34

10
7 OPERATION
WARNING
Make sure that specific warnings and cautions in Chapter 2 “Precautions” are carefully read, understood and applied!
Fig. 7.a Temperature probes
in LEFT orientation
Intake air from outside
Exhaust air to outside
Supply air to inside
Extract air from inside
A
B
D
C
R
EGH
J
K
Q
PN
E
G
DATE:showsthecurrentdate
MODE:showstheoperationmode
SPEED:shows the selected speed
TIME:showsthetime
FILTER ALARM:showsthatltersneedtobemaintained/replaced
BOOST:showsthatBOOSTspeedisactivated
BOOST KEY:tomanuallyactivatetheBOOSTspeed
FILTER RESET KEY:toresettheFilterAlarm
ESCkey:toexitandgobacktothepreviousmenu
OKkey:toentertheselectedmenu
to go DOWN with the menu selection
to go UP with the menu selection
to power off the ventilation unit
shows ERROR ALARM - see point 7.3 to check the type of error
this symbol shows if the bypass is active
this symbol shows that ANTI-FROST is active
this symbol shows that the IAQ input is activated, i.e.CO2
this symbol shows that the HY input is activated.
this symbol shows that NIGHT MODE is activated
this symbol shows that Heating output is activated
H
J
K
N
O
P
Q
R
S
U
X
Some operations can be selected either from the CTRL-DSP buttons or from the menu
W
VUTS X
OML
F
I
F
I
L
M
T
V
W
Fig. 7.b CTRL-DSP
In case of RIGHT orientation, follows instructions as per point 3.3 - Fig. 3.b in order to get the temperature probes operate
correctly.
A
B
D
C
T12
T21
T11 T22
EXTRACT
SUPPLY
INTAKE
EXHAUST