Heat & Glo Pier-HV-IPI User manual

Heat & Glo • PIER-HV-IPI, ST-HV-IPI,L&R-COR-HV-IPI • 2005-900 Rev.K • 11/06 1
Models:
Pier-HV-IPI
ST-HV-IPI
LCOR-HV-IPI
RCOR-HV-IPI
IntheCommonwealthofMassachusetts:
• installation must be performed by a licensed
plumberorgasfitter;
See Table of Contents for location of additional
CommonwealthofMassachusettsrequirements.
- Do not store or use gasoline or other flam-
mablevaporsandliquidsinthevicinityofthis
oranyotherappliance.
- What to do if you smell gas
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Donotuseanyphoneinyourbuilding.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call
thefiredepartment.
- Installationandservicemustbeperformedbya
qualified installer, service agency, or the gas
supplier.
WARNING: IMPROPER INSTALLA-
TION, ADJUSTMENT, ALTERATION,
SERVICE OR MAINTENANCE CAN
CAUSE INJURY OR PROPERTY DAM-
AGE. REFER TO THIS MANUAL. FOR
ASSISTANCE ORADDITIONAL INFOR-
MATION CONSULT A QUALIFIED IN-
STALLER, SERVICEAGENCY, OR THE
GAS SUPPLIER.
READ THIS MANUAL BEFORE INSTALLING OR
OPERATING THISAPPLIANCE. THIS INSTALLERS
GUIDE MUST BE LEFT WITH APPLIANCE FOR
FUTUREREFERENCE.
1.This appliance may be installed in an af-
termarket,permanentlylocated,manufac-
tured(mobile)home,wherenotprohibited
bylocalcodes.
2. Thisapplianceisonlyfor usewiththe type
of gas indicated on the rating plate. This
appliance is not convertible for use with
othergases,unlessacertifiedkitisused.
Please contact your Heat & Glo dealer with any
questionsorconcerns. For thelocation of yournearest
Heat & Glo dealer, please visitwww.heatnglo.com.
Printed in U.S.A. Copyright 2006
Heat &Glo,abrand of Hearth &HomeTechnologiesInc.
20802KensingtonBoulevard,Lakeville,MN55044
WARNING: IF THE INFORMATION
IN THESE INSTRUCTIONS IS NOT
FOLLOWED EXACTLY,AFIRE OR
EXPLOSION MAY RESULT CAUS-
ING PROPERTY DAMAGE, PER-
SONAL INJURY, OR DEATH.
Owner’s Manual
Installation and Operation
Thisproductmaybecoveredbyoneormoreofthefollowingpatents:(UnitedStates)4593510,4686807,4766876,4793322,4811534,5000162,5016609,5076254,5113843,5191877,5218953,5263471,
5328356,5341794,5347983,5429495,5452708,5542407,5601073,5613487,5647340,5688568,5762062,5775408,5890485,5931661,5941237,5947112,5996575,6006743,6019099,6048195,6053165,
6145502,6170481,6237588, 6296474, 6374822,6413079,6439226,6484712,6543698,6550687,6601579,6672860,6688302B2, 6715724B2, 6729551, 6736133,6748940,6748942,6769426,6774802,
6796302,6840261,6848441,6863064,6866205, 6869278, 6875012, 6880275, 6908039,6919884,D320652,D445174,D462436; (Canada) 1297749,2195264,2225408,2313972;(Australia) 780250,
780403,1418504 or otherU.S.and foreign patentspending.

Heat & Glo • PIER-HV-IPI, ST-HV-IPI, L&R-COR-HV-IPI • 2005-900 Rev. K • 11/062
These units MUST use one of the vent systems
described in the Installing the Fireplace section of
the Installers Guide. NO OTHER vent systems or
components MAY BE USED.
This gas fireplace and vent assembly MUST be
vented directly to the outside and MUST NEVER be
attached to a chimney serving a separate solid fuel
burning appliance. Each gas appliance MUST USE
a separate vent system. Common vent systems are
PROHIBITED.
INSPECT the external vent cap on a regular basis to
make sure that no debris is interfering with the air
flow.
The glass door assembly MUST be in place and
sealed, and the trim door assembly MUST be in
place on the fireplace before the unit can be placed
into safe operation.
DO NOT OPERATE this appliance with the glass
door removed, cracked, or broken. Replacement of
the glass door should be performed by a licensed
or qualified service person. DO NOT strike or slam
the glass door.
The glass door assembly SHALL ONLY be
replaced as a complete unit, as supplied by the gas
fireplace manufacturer. NO SUBSTITUTE material
may be used.
DO NOT USE abrasive cleaners on the glass door
assembly. DO NOT ATTEMPT to clean the glass
door when it is hot.
Turn off the gas before servicing this appliance. It is
recommended that a qualified service technician
perform an appliance check-up at the beginning of
each heating season.
Any safety screen or guard removed for servicing
must be replaced before operating this appliance.
DO NOT place furniture or any other combustible
household objects within 36 inches of the fireplace
front.
READ and UNDERSTAND all instructions carefully
before starting the installation. FAILURE TO
FOLLOW these installation instructions may result
in a possible fire hazard and will void the warranty.
Prior to the first firing of the fireplace, READ the
Using Your Fireplace section of the Owners Guide.
DO NOT USE this appliance if any part has been
under water. Immediately CALL a qualified service
technician to inspect the unit and to replace any part
of the control system and any gas control which has
been under water.
THIS UNIT IS NOT FOR USE WITH SOLID FUEL.
Installation and repair should be PERFORMED by a
qualified service person. The appliance and venting
system should be INSPECTED before initial use
and at least annually by a professional service
person. More frequent cleaning may be required
due to excessive lint from carpeting, bedding
material, etc. It is IMPERATIVE that the unit’s
control compartment, burners, and circulating air
passageways BE KEPT CLEAN to provide for
adequate combustion and ventilation air.
Always KEEP the appliance clear and free from
combustible materials, gasoline, and other
flammable vapors and liquids.
NEVER OBSTRUCT the flow of combustion and
ventilation air. Keep the front of the appliance
CLEAR of all obstacles and materials for servicing
and proper operations.
Due to the high temperature, the appliance should
be LOCATED out of traffic areas and away from
furniture and draperies. Clothing or flammable
material SHOULD NOT BE PLACED on or near the
appliance.
Children and adults should be ALERTED to the
hazards of high surface temperature and should
STAY AWAY to avoid burns or clothing ignition.
Young children should be CAREFULLYSUPERVISED
when they are in the same room as the appliance.
!
!
!
!
!
!
!
!!
!
!
!
!
!
!
!
!
Safety and Warning Information
!
!

Heat & Glo • PIER-HV-IPI, ST-HV-IPI,L&R-COR-HV-IPI • 2005-900 Rev. K • 11/06 3
Table of Contents
Safety and Warning Information.................................................. 2
Service Parts List ......................................................................... 4
Approvals and Codes ................................................................ 13
ApplianceCertification ................................................................................. 13
InstallationCodes ........................................................................................ 13
HighAltitude Installations............................................................................. 13
Requirementsforthe Commonwealth of Massachusetts .............................. 14
Getting Started............................................................................ 15
IntroducingtheHeat&GloGasFireplaces .................................................. 15
Pre-installPreparation ................................................................................. 15
Installing the Fireplace ............................................................... 19
Step 1. Locating the Fireplace .................................................................... 19
Step 2. Framing the Fireplace ..................................................................... 20
Step 3. Installing the Vent System .............................................................. 23
A. Vent SystemApprovals ......................................................... 23
B. Installing Vent Components ................................................... 30
C. VentTermination.................................................................... 32
Step4. Positioning,Leveling,and Securing the Fireplace ........................... 35
Step 5. The Gas Control System ................................................................ 35
Step 6. The Gas Supply Line ...................................................................... 36
Step 7. Gas Pressure Requirements........................................................... 36
Step 8. Wiring the Fireplace........................................................................ 37
Step 9. Finishing......................................................................................... 40
Step10. InstallingTrim,Logs&Ember Material .......................................... 41
Installing theTrim .......................................................................... 41
PositioningtheLogs...................................................................... 41
Shutter Settings ............................................................................ 41
GlassSpecifications...................................................................... 41
PreparingElectricEmberBed and Lava Rock ............................... 41
PlacingtheEmberMaterial ........................................................... 43
EmberLightBulb Replacement ..................................................... 43
Step 11. Before Lighting the Fireplace........................................................ 44
Step 12. Lighting the Fireplace ................................................................... 44
After theInstallation ..................................................................................... 44
Maintaining and Servicing Your Fireplace................................ 45
Î= Containsupdatedinformation.
Í
Í
Î
Î

Heat & Glo • PIER-HV-IPI, ST-HV-IPI, L&R-COR-HV-IPI • 2005-900 Rev. K • 11/064
6 Log Assembly
(NG, LP) Exploded Parts Diagram
Service Parts Pier-HV-IPI
Beginning Manufacturing Date: 6-03
Ending Manufacturing Date: ______
5
2
1
3
4
Grate
Bar

Heat & Glo • PIER-HV-IPI, ST-HV-IPI,L&R-COR-HV-IPI • 2005-900 Rev. K • 11/06 5
AVAILABLE
TO SHIP IN 24
HOURS
ITEM DESCRIPTION SERIAL # PART NUMBER
Burner Orifice NG (#33DMS) 582-833 Y
Burner Orifice LP (#50DMS) 582-850 Y
1 End Glass Assembly GLA-MS Y
2 Glass Door Assembly GLA-6TROC Y
3 Burner Assembly 2005-006 Y
4 Log Grate 2005-012
5SideRefractory SRV2005-730
6 Log Set Assembly LOGS-MSR Y
7 Log 1 SRV2005-701
8 Log 2 SRV2005-700
9 Log 3 SRV2005-702
10 Log 4 SRV2005-703
11 Log 5 SRV2005-704
12 Log 6 SRV2005-705
13 Log 7 SRV703-703
Lava Rock Bag 2005-790
Flue Restrictor 385-128
Teco-Sil, 5 lb. bag 700-790
Ember Mesh Assembly 2006-008 Y
Junction Box 4021-013 Y
Non-Combustible Board (side) 2006-136
Non-Combustible Board (end) 2006-137
3V Adaptor Plug 593-593A Y
Battery Pack 593-594A Y
Fiberglass Rope 060-455
Glass Latch Support Assembly 386-122A Y
Mineral Wool 050-721
ConversionKit NG NGK-MS Y
ConversionKit LP LPK-MS Y
ACCESSORIES
Fan Kit GFK-160A
Remote Control Kit RC-SMART-HNG
Remote Control Kit SMART-STAT-HNG
Remote Control - Multi-functional RCT-MLT-HNG
Wall Switch, Multi-functional WSK-MLT
Plug Adapator Kit (for WSK-MLT) PLUG-ADP
Louvers withMesh MS-LOUVERS
Louvers withMesh- End Panel MS-LOUVERS-EP
Service Parts List (NG, LP)
IMPORTANT:THISISDATEDINFORMATION.The mostcurrentinformationislocated onyourdealers VIPsite.Whenordering,
supplyserialandmodelnumberstoensurecorrect service parts.
PIER-HV-IPI
Î

Heat & Glo • PIER-HV-IPI, ST-HV-IPI, L&R-COR-HV-IPI • 2005-900 Rev. K • 11/066
(NG, LP) Exploded Parts Diagram
Service Parts ST-HV-IPI
Beginning Manufacturing Date: 6-03
Ending Manufacturing Date: ______
5 Log Assembly
4
2
3
1
Grate
Bar

Heat & Glo • PIER-HV-IPI, ST-HV-IPI,L&R-COR-HV-IPI • 2005-900 Rev. K • 11/06 7
AVAILABLE TO
SHIP IN 24
HOURS
ITEM DESCRIPTION SERIAL # PART NUMBER
Burner Orifice NG (#32DMS) 582-832 Y
Burner Orifice LP (#50DMS) 582-850 Y
1 Glass Door Assembly GLA-6TROC Y
2 Burner Assembly 2005-006 Y
3 Log Grate 2005-012
4 Side Refractory SRV2005-730
5 Log Set Assembly LOGS-MSR Y
6Log1 SRV2005-701
7Log2 SRV2005-700
8Log3 SRV2005-702
9Log4 SRV2005-703
10 Log 5 SRV2005-704
11 Log 6 SRV2005-705
12 Log 7 SRV703-703
Lava Rock Bag 2005-790
Flue Restrictor 385-128
Teco-Sil, 5 lb. bag 700-790
Hood, black SRV60-143-BK
Ember Mesh Assembly 2005-008 Y
Non-Combustible Board 2005-172
Junction Box 4021-013 Y
Fiberglass Rope 060-455
Glass Latch Support Assembly 386-122A Y
Mineral Wool 050-721
3V Adaptor Plug 593-593A Y
Battery Pack 593-594A Y
Conversion Kit NG NGK-MS Y
Conversion Kit LP LPK-MS Y
ACCESSORIES
Fan Kit GFK-160A
Remote Control Kit RC-SMART-HNG
Remote Control Kit SMART-STAT-HNG
Remote Control - Multi-functional RCT-MLT-HNG
Wall Switch, Multi-functional WSK-MLT
Plug Adapator Kit (for WSK-MLT) PLUG-ADP
Louvers with Mesh MS-LOUVERS
Louvers with Mesh - End Panel MS-LOUVERS-EP
Service Parts List (NG, LP)
IMPORTANT:THISISDATEDINFORMATION.The mostcurrentinformationislocated onyourdealers VIPsite.Whenordering,
supplyserialandmodelnumberstoensurecorrect service parts.
ST-HV-IPI
Î

Heat & Glo • PIER-HV-IPI, ST-HV-IPI, L&R-COR-HV-IPI • 2005-900 Rev. K • 11/068
Partnumberlistonfollowing page.
7 Log Assembly
15
(NG, LP) Exploded Parts Diagram
Service Parts LCOR-HV-IPI
Beginning Manufacturing Date: 6-03
Ending Manufacturing Date: ______
1
2
3
45
6
15

Heat & Glo • PIER-HV-IPI, ST-HV-IPI,L&R-COR-HV-IPI • 2005-900 Rev. K • 11/06 9
AVAILABLE TO
SHIP IN 24
HOURS
ITEM COMMON PARTS SERIAL # PART NUMBER
Burner Orifice NG (#32DMS) 582-832 Y
Burner Orifice LP (#50DMS) 582-850 Y
1EndGlassAssembly GLA-MS Y
2 Glass Door Assembly GLA-6TROC Y
3BurnerAssembly 2005-006 Y
4 Log Grate 2005-012
5 Side Refractory SRV2005-730
6 Refractory, Back SRV2005-731
7 Log Set Assembly LOGS-MSR Y
8Log1 SRV2005-701
9Log2 SRV2005-700
10 Log 3 SRV2005-702
11 Log 4 SRV2005-703
12 Log 5 SRV2005-704
13 Log 6 SRV2005-705
14 Log 7 SRV703-703
Lava Rock Bag 2005-790
Flue Restrictor 385-128
Teco-Sil, 5 lb. bag 700-790
Ember Mesh Assembly 2006-008
Non-Combustible Board (side) 2006-136
Non-Combustible Board (end) 2008-114
Junction Box 4021-013
Fiberglass Rope 060-455
Glass Latch Support Assembly 386-122A Y
Mineral Wool 050-721
3V Adaptor Plug 593-593A Y
BatteryPack 593-594A Y
Conversion Kit NG NGK-MS Y
Conversion Kit LP LPK-MS Y
ACCESSORIES
Fan Kit GFK-160A
Remote Control Kit RC-SMART-HNG
Remote Control Kit SMART-STAT-HNG
Remote Control - Multi-functional RCT-MLT-HNG
Wall Switch, Multi-functional WSK-MLT
Plug Adapator Kit (for WSK-MLT) PLUG-ADP
Louvers withMesh MS-LOUVERS
Louvers with Mesh- End Panel MS-LOUVERS-EP
Service Parts List (NG, LP)
IMPORTANT:THISISDATEDINFORMATION.Themostcurrentinformation islocatedon yourdealersVIPsite.Whenordering,
supplyserialandmodelnumberstoensurecorrect service parts.
LCOR-HV-IPI
Î

Heat & Glo • PIER-HV-IPI, ST-HV-IPI, L&R-COR-HV-IPI • 2005-900 Rev. K • 11/0610
Partnumberlistonfollowing page.
7 Log Assembly
(NG, LP) Exploded Parts Diagram
Service Parts RCOR-HV-IPI
Beginning Manufacturing Date: 6-03
Ending Manufacturing Date: ______
1
2
3
4
15
5
6
Grate
Bar

Heat & Glo • PIER-HV-IPI, ST-HV-IPI,L&R-COR-HV-IPI • 2005-900 Rev. K • 11/06 11
Service Parts List (NG, LP)
IMPORTANT:THISISDATEDINFORMATION.The mostcurrentinformationislocated onyourdealers VIPsite.Whenordering,
supplyserialandmodelnumberstoensurecorrect service parts.
RCOR-HV-IPI
AVAILABLE
TO SHIP IN 24
HOURS
ITEM COMMON PARTS SERIAL # PART NUMBER
Burner Orifice NG (#32DMS) 582-832 Y
Burner Orifice LP (#50DMS) 582-850 Y
1EndGlassAssembly GLA-MS Y
2 Glass Door Assembly GLA-6TROC Y
3 Burner Assembly 2005-006 Y
4 Log Grate 2005-012
5 Side Refractory SRV2005-730
6 Refractory, Back SRV2005-731
7 Log Set Assembly LOGS-MSR Y
8 Log 1 SRV2005-701
9 Log 2 SRV2005-700
10 Log 3 SRV2005-702
11 Log 4 SRV2005-703
12 Log 5 SRV2005-704
13 Log 6 SRV2005-705
14 Log 7 SRV703-703
Lava Rock Bag 2005-790
Flue Restrictor 385-128
Teco-Sil, 5 lb. bag 700-790
Ember Mesh Assembly 2006-008 Y
Non-Combustible Board (side) 2006-136
Non-Combustible Board (end) 2008-114
Junction Box 4021-013 Y
3V Adaptor Plug 593-593A Y
Battery Pack 593-594A Y
Fiberglass Rope 060-455
Glass Latch Support Assembly 386-122A Y
Mineral Wool 050-721
Conversion Kit NG NGK-MS Y
Conversion Kit LP LPK-MS Y
ACCESSORIES
Fan Kit GFK-160A
Remote Control Kit RC-SMART-HNG
Remote Control Kit SMART-STAT-HNG
Remote Control - Multi-functional RCT-MLT-HNG
Wall Switch, Multi-functional WSK-MLT
Plug Adapator Kit (for WSK-MLT) PLUG-ADP
Louvers with Mesh MS-LOUVERS
Louvers with Mesh - End Panel MS-LOUVERS-EP
Î

Heat & Glo • PIER-HV-IPI, ST-HV-IPI, L&R-COR-HV-IPI • 2005-900 Rev. K • 11/0612
(NG, LP) Exploded Parts Diagram
Service Parts L&RCOR-HV-IPI
Beginning Manufacturing Date: 6-03
Ending Manufacturing Date: ______
PIER-HV-IPI,ST-HV-IPI
NOTE: Replacementbulbsto be suppliedbyhomeowner. Recommended replacements:SylvaniaMini Candelabra 75watts.
1245
6
7
8
9
10
3
11
12
14
13
AVAILABLE TO
SHIP IN 24
HOURS
ITEM DESCRIPTION SERIAL # PART NUMBER
1 ON/OFF Rocker Switch 060-511 Y
2ON/OFFWireAssembly 060-521A Y
3ValveNG 750-500 Y
3ValveLP 750-501 Y
4 Flexible Gas Connector 2005-009 Y
5Module 593-592 Y
6WireAssembly 593-590A Y
7 Ember Box Assembly 2005-114 Y
8 Pilot Assembly NG 385-510A Y
8 Pilot Assembly LP 385-511A Y
9 Pilot Bracket 2005-118
10 Gasket Orifice 2005-166
11 Valve Bracket 2005-120
12 Flex Ball Valve Assembly 302-320A Y
13 Pilot AssemblySupport 385-120
14 Ground Strap 385-512
Regulator, NG NGK-DXV Y
Regulator, LP LPK-DXV Y
Pilot Tube 446-301 Y
Orifice Spud NG 446-505 Y
Orifice Spud LP 446-517 Y

Heat & Glo • PIER-HV-IPI, ST-HV-IPI,L&R-COR-HV-IPI • 2005-900 Rev. K • 11/06 13
Appliance Certification
TheHeat& Glofireplacemodels discussedinthisInstallers
Guidehavebeen testedtocertification standardsandlisted
bytheapplicablelaboratories.
Certification
MODELS: PIER-HV-IPI, ST-HV-IPI,
LCOR-HV-IPI, RCOR-HV-IPI
LABORATORY: Underwriters Laboratories
TYPE: Direct Vent Gas Fireplace Heater
STANDARD: ANSI Z21.88•CGA2.22•UL307B
Installation Codes
Thefireplaceinstallationmustconformtolocalcodes.Before
installing the fireplace, consult the local building code
agency to ensure that you are in compliance with all
applicable codes, including permits and inspections.
Intheabsence oflocalcodes, thefireplaceinstallation must
conformtothe NationalFuelGasCodeANSI Z223.1(inthe
United States) or the CAN/CGA-B149 Installation Codes
(in Canada). The appliance must be electrically grounded
in accordance with local codes or, in the absence of local
codes with the National Electric CodeANSI/NFPANo. 70
(intheUnitedStates),orto the CSAC22.1CanadianElectric
Code(inCanada).
Thesemodelsmaybe installed in a bedroom orbed-sitting
room in the U.S.A. and Canada.
1Approvals and
Codes
HighAltitude Installations
U.L. Listed gas appliances are tested and approved with-
outrequiringchangesforelevationsfrom0to2,000feetin
the U. S.A. and in Canada.
Wheninstallingthisapplianceatanelevationabove2,000
feet, it may be necessary to decrease the input rating by
changingtheexistingburnerorificetoasmallersize.Input
rate should be reduced by 4% for each 1000 feet above a
2000 foot elevation in the U.S.A. or 10% for elevations
between2000 and4500feet inCanada.If theheatingvalue
of the gas has been reduced, these rules do not apply. To
identify the proper orifice size, check with the local gas
utility.
Ifinstalling this appliance at an elevation above 4,500 feet
(in Canada), check with local authorities.
Heat & Glo Quality Systems
registeredby SGS ICS

Heat & Glo • PIER-HV-IPI, ST-HV-IPI, L&R-COR-HV-IPI • 2005-900 Rev. K • 11/0614
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where the
side wall exhaust vent termination is less than seven (7)
feetabovefinished grade in theareaofthe venting, includ-
ing but not limited to decks and porches, the following re-
quirements shall be satisfied:
Installation of Carbon Monoxide Detectors
Atthetimeofinstallationofthesidewallhorizontalvented
gas fueled equipment, the installing plumber or gasfitter
shallobservethata hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the floor
level where the gas equipment is to be installed. In addi-
tion,theinstallingplumberorgasfittershallobservethata
battery operated or hard wired carbon monoxide detector
with an alarm is installed on each additional level of the
dwelling,buildingorstructureservedbythesidewallhori-
zontalventedgas fueled equipment. Itshallbethe respon-
sibilityofthe property ownertosecurethe services ofqual-
ifiedlicensedprofessionals fortheinstallation ofhardwired
carbonmonoxidedetectors.
In the event that the side wall horizontally vented gas fu-
eledequipmentisinstalledina crawl space or an attic, the
hard wired carbon monoxide detector with alarm and bat-
tery back-up may be installed on the next adjacent floor
level.
In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
ownershallhavea period of thirty(30)daystocomply with
theaboverequirements;provided,however,thatduringsaid
thirty(30)dayperiod, a battery operatedcarbonmonoxide
detector with an alarm shall be installed.
Approved Carbon Monoxide Detectors
Eachcarbonmonoxide detectorasrequiredin accordance
withtheaboveprovisionsshall comply with NFPA720and
beANSI/UL2034 listed and IAS certified.
Signage
Ametalorplasticidentification plate shall be permanently
mountedtothe exterior ofthebuildingat a minimumheight
of eight (8) feet above grade directly in line with the ex-
haust vent terminal for the horizontally vented gas fueled
heating appliance or equipment. The sign shall read, in
print size no less than one-half (1/2) inch in size, “GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB-
STRUCTIONS”.
Inspection
Thestateor local gas inspector of the side wall horizontally
ventedgasfueled equipment shallnotapprove the installa-
tionunless, uponinspection,the inspectorobservescarbon
monoxidedetectorsandsignageinstalledinaccordancewith
theprovisions of248CMR5.08(2)(a)1through 4.
Exemptions
Thefollowingequipmentisexemptfrom248CMR5.08(2)(a)1
through4:
• Theequipmentlistedin Chapter 10 entitled “Equipment
Not Required To Be Vented” in the most current edition
of NFPA54 as adopted by the Board; and
• ProductApproved side wall horizontally vented gas fu-
eled equipment installed in a room or structure sepa-
ratefrom thedwelling,buildingorstructureusedin whole
orinpartforresidentialpurposes.
MANUFACTURERREQUIREMENTS
Gas Equipment Venting System Provided
Whenthemanufacturerof ProductApprovedsidewall hor-
izontallyventedgasequipmentprovidesaventingsystem
designorventingsystemcomponentswith the equipment,
the instructions provided by the manufacturer for installa-
tionoftheequipment and the venting system shallinclude:
• Detailed instructions for the installation of the venting
system design or the venting system components; and
• A complete parts list for the venting system design or
ventingsystem.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall
horizontallyventedgasfueled equipment does not provide
the parts for venting the flue gases, but identifies “special
venting systems”, the following requirements shall be sat-
isfiedbythemanufacturer:
• Thereferenced“specialventingsystem”instructionsshall
beincludedwiththe appliance or equipmentinstallation
instructions;and
• The“special ventingsystems” shallbe ProductApproved
by the Board, and the instructions for that system shall
includeapartslistanddetailedinstallation instructions.
A copy of all installation instructions for all Product Ap-
provedsidewallhorizontally vented gas fueledequipment,
all venting instructions, all parts lists for venting instruc-
tions, and/or all venting design instructions shall remain
with the appliance or equipment at the completion of the
installation.
See Gas Connection section for additional Common-
wealth of Massachusetts requirements.
NOTE: The following requirements reference various
Massachusetts and national codes not contained in
this document.
G. Requirements for the Commonwealth of
Massachusetts

Heat & Glo • PIER-HV-IPI, ST-HV-IPI,L&R-COR-HV-IPI • 2005-900 Rev. K • 11/06 15
2Getting Started
Introducing the Heat & Glo Gas Fireplaces
Heat&Glodirectvent gas fireplaces are designed tooper-
ate with all combustion air siphoned from outside of the
building and all exhaust gases expelled to the outside.
The information contained in this Installers Guide, unless
noted otherwise, applies to all models and gas control
systems.Gas fireplacediagrams,including thedimensions,
are shown in this section.
Pre-install Preparation
Thisgas fireplace and its components are tested and safe
when installed in accordance with this Installers Guide.
Report to your dealer any parts damaged in shipment,
particularly the condition of the glass. Do not install any
unit with damaged, incomplete, or substitute parts.
Thevent systemcomponents areshipped inseparatepack-
ages. The gas logs are packaged separately and must be
fieldinstalled.
Read all of the instructions before starting the instal-
lation. Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
Failure to follow these instructions will void the own-
er’s warranty and may present a fire hazard.
TheHeat&GloWarrantywillbevoidedby,andHeat&Glo
disclaims any responsibility for, the following actions:
• Installation of any damaged fireplace or vent system
component.
• Modification of the fireplace or direct vent system.
• Installation other than as instructed by Heat & Glo.
• Improper positioning of the gas logs or the glass door.
• Installationand/oruse of anycomponentpartnot manu-
factured and approved by Heat & Glo, not withstanding
anyindependenttestinglaboratoryorotherpartyapproval
of such component part or accessory.
ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE
HAZARD.
When planning a fireplace installation, it’s necessary
to determine:
•Where the unit is to be installed.
•Thevent system configuration to be used.
•Gas supply piping.
•Electricalwiring.
•Framingandfinishingdetails.
•Whether optional accessories—devices such as a fan,
wallswitch, or remote control—are desired.
If the fireplace is to be installed on carpeting or tile,
or on any combustible material other than wood
flooring, the fireplace should be installed on a metal
or wood panel that extends the full width and depth
of the fireplace.

Heat & Glo • PIER-HV-IPI, ST-HV-IPI, L&R-COR-HV-IPI • 2005-900 Rev. K • 11/0616
Figure 1. Diagram of the PIER-HV-IPI
5-1/4
(133mm)
1/2
(13mm)
12
(306mm)
Ø8
(205mm)
42-5/8
(1082mm)
Ø8
(205mm)
12
(305mm)
ELECTRICAL
ACCESS
GAS LINE
ACCESS
34-3/4
(883mm)
4-1/16
(102mm)
4-1/2
(114mm) 4-3/4 (121mm)
2-5/16
(58mm) 37-7/16
(950mm)
17-15/16
(455mm)
24
(610mm)
21-9/16
(547mm)
32-5/16
(820mm)
21-9/16
(547mm)
42
(1067mm)
REAR VENT
COLLARS
ELECTRICAL
ACCESS
GAS LINE
ACCESS
GAS CONTROLS
& LABELS
SIDE GLASS
DOOR
TOP STANDOFFS
TOP VENT
COLLARS

Heat & Glo • PIER-HV-IPI, ST-HV-IPI,L&R-COR-HV-IPI • 2005-900 Rev. K • 11/06 17
Figure 2. Diagram of the ST-HV-IPI
5-14
(133mm)
12
(306mm)
1/2
(13mm)
(4)
46-5/8
(1183mm)
42
(1067mm)
32-5/16
(821mm)
21-9/16
(548mm)
36-3/16
(919mm)
2-5/16
(58mm)
4-3/4
(121mm)
4-1/16
(102mm)
4-1/2
(114mm)
ELECTRICAL
ACCESS
GAS LINE
ACCESS
12
(305mm)
4-1/2
(114mm)
2-9/16
(64mm)
24
(610mm)
8-1/2
(216mm)
34-3/4
(882mm)
Ø8
(205mm)
Ø8
(205mm)
REAR VENT
COLLARS
ELECTRICAL
ACCESS
GAS LINE
ACCESS
GAS CONTROLS
& LABELS SIDE GLASS
DOOR
TOP STANDOFFS
TOP VENT
COLLARS

Heat & Glo • PIER-HV-IPI, ST-HV-IPI, L&R-COR-HV-IPI • 2005-900 Rev. K • 11/0618
Figure 3. Diagram of the LCOR-HV-IPI and RCOR-HV-IPI
5-1/4
(133mm)
1/2
(13mm)
(4)
Ø8
(205mm)
12-1/16
(306mm)
12
(305mm)
Ø8
(205mm)
34-3/4
(882mm)
10
(254mm)
7-1/4
(184mm)
4-3/4
(121mm)
32-5/16
(821mm)
37-7/16
(950mm)
ELECTRICAL
ACCESS
GAS LINE
ACCESS
42-5/8
(1083mm
2-9/16
(64mm)
2-5/16
(58mm)
17-15/16
(455mm)
21-9/16
(547mm)
24-1/8
(612mm)
29-1/4
(743mm)
42
(1067mm)
21-9/16
(548mm)
REAR VENT
COLLARS
ELECTRICAL
ACCESS
GAS LINE
ACCESS
GAS CONTROLS
& LABELS
END GLASS
DOOR
TOP STANDOFFS
TOP VENT
COLLARS
SIDE GLASS
DOOR

Heat & Glo • PIER-HV-IPI, ST-HV-IPI,L&R-COR-HV-IPI • 2005-900 Rev. K • 11/06 19
3Installing the Fireplace
Step 1. Locating the Fireplace
The diagram below shows space and clearance require-
ments for locating a fireplace within a room.
Figure 4A. Fireplace Dimensions and Locations
36"
GLASS
GLASS
GLASS
36"
GLASS
GLASS
36"
GLASS
36"
GLASS
GLASS
GLASS
36"
36"
36"
PIER-HV-IPI
TOP VIEW RCOR-HV-IPI
TOP VIEW
LCOR-HV-IPI
TOP VIEW
ST-HV-IPI
TOP VIEW
Clearance Requirements
The top, back, and sides of the fireplace are defined by
stand-offs.Theminimumclearance to a perpendicularwall
extendingpastthe faceofthe fireplaceisone inch (25mm).
ThemetalendsofthefireplacemayNOT berecessedinto
combustible construction.
Note: Refer to Figure 4B fordimensionsand appliance
locationsifinstalling aPier-HVunitwith a Catalina shelf
and/or marble package.
Note: Refer to the Catalina installation instruction
included with kit for assembly and installation. Figure 4B.
50-1/2 in.
34-1/2 in.
7 in.
47-1/2 in.
45-1/4 in.
13/16 in.
Marble sizes (inches):
Header.................................. 26 x 8
Side headers..................45-1/2 x 8
Legs................................ 33-1/2 x 7
45 -1/4 in.
(1149mm)
FINISHED
WALL
Fireplace Locations/Dimensions with
Catalina Shelf/Marble Package ONLY
Note: This location diagram MUST be followed when in-
stalling a Pier-HV with a Catalina shelf/marble package
since the fireplace is installed further from finished wall.

Heat & Glo • PIER-HV-IPI, ST-HV-IPI, L&R-COR-HV-IPI • 2005-900 Rev. K • 11/0620
Minimum Clearances
from the Fireplace to Combustible Materials
Inches mm
Glass Sides or Ends.......... 36 .................... 914
Floor ................................... 0 ....................... 0
RearVent...........................1/2 ..................... 13
Metal Sides or Ends ..........1/2..................... 13
Top................................... 2 1/2 ................... 64
Ceiling* .............................. 31 .................... 787
For minimum clearances, see the direct vent termination
clearance diagrams on pages 31 and 32 in this manual.
Minimum Clearances
from the Vent Pipe to Combustible Materials
Inches mm
Vertical Sections. ............. 1 ................ 25
Horizontal Sections
Top..................................... 3 ................ 75
Bottom ............................... 1 ................ 25
Sides ................................. 1 ................ 25
At Wall Firestops
Top.................................. 2 1/2 ............63.7
Bottom ..............................1/2............... 13
Sides ................................. 1 ................ 25
* Theclearancetotheceilingismeasuredfromthetopof
theunit, excludingthestandoffs (seeFigures37 & 38).
Thedistancefromthe unit to combustibleconstructionisto
be measured from the unit outer wrap surface to the com-
bustible construction, NOT from the screw heads that se-
curetheunittogether.
!
WARNING: FRAMING DIMENSIONS ASSUME
USE OF 1/2 INCH THICK WALL COVERING
MATERIALS ONEXTERIOR OFFRAMING ONLYAND
NO SHEETROCK ON INTERIOR OF FRAMING.
Step 2. Framing the Fireplace
Fireplaceframingcan bebuiltbefore or afterthefireplace is
set in place. Framing should be positioned to accommo-
date wall coverings and fireplace facing material. The dia-
grambelowshows framingreferencedimensions.
CAUTION: MEASURE FIREPLACE DIMENSIONS AND
VERIFY FRAMING METHODS AND WALL COVERING
DETAILS BEFORE FRAMING.