Heat-N-Glo CFX-DIAMOND Assembly instructions

Model:
CFX-DIAMOND Installers Guide
593-900H 8/02
Underwriters
LaboratoriesListed
- Do not store or use gasoline or other flam-
mablevaporsandliquidsinthevicinityofthis
orany other appliance.
-What to do if you smell gas
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call
thefiredepartment.
- Installationandservicemustbeperformedbya
qualified installer, service agency, or the gas
supplier.
WARNING: IMPROPER INSTALLA-
TION, ADJUSTMENT, ALTERATION,
SERVICE OR MAINTENANCE CAN
CAUSE INJURY OR PROPERTY DAM-
AGE. REFER TO THIS MANUAL. FOR
ASSISTANCE OR ADDITIONAL INFOR-
MATION CONSULT A QUALIFIED IN-
STALLER, SERVICEAGENCY, OR THE
GAS SUPPLIER.
READ THIS MANUAL BEFORE INSTALLING OR
OPERATING THIS APPLIANCE. THIS INSTALLERS
GUIDE MUST BE LEFT WITH APPLIANCE FOR
FUTUREREFERENCE.
1.Thisappliancemaybeinstalledin anaf-
termarket,permanently located,manu-
factured(mobile) home, where not pro-
hibitedby local codes.
2. Thisapplianceisonlyforusewiththetype
of gas indicated on the rating plate. This
appliance is not convertible for use with
othergases,unlessacertifiedkitisused.
Please contact your Heat-N-Glo dealer with any
questionsorconcerns.Forthenumberofyournearest
Heat-N-Glo dealer, please call 1-888-427-3973.
PrintedinU.S.A. Copyright 2002,
Heat-N-Glo,adivisionofHearthTechnologiesInc.
20802KensingtonBoulevard,Lakeville,MN55044
WARNING: IF THE INFORMATION
IN THESE INSTRUCTIONS IS NOT
FOLLOWED EXACTLY,AFIRE OR
EXPLOSION MAY RESULT CAUS-
ING PROPERTY DAMAGE, PER-
SONAL INJURY, OR DEATH.
This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322;
4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia)
543790; 586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.

2
SAFETY AND WARNING INFORMATION
READ and UNDERSTAND all instructions carefully before starting the installation.
FAILURE TO FOLLOW these installation instructions may result in a possible fire
hazard and will void the warranty.
Prior to the first firing of the fireplace, READ the Using Your Fireplace section of the
Owners Guide.
DO NOT USE this appliance if any part has been under water. Immediately CALL a
qualified service technician to inspect the unit and to replace any part of the control
system and any gas control which has been under water.
THIS UNIT IS NOT FOR USE WITH SOLID FUEL.
Installation and repair should be PERFORMED by a qualified service person. The
appliance and venting system should be INSPECTED before initial use and at least
annually by a professional service person. More frequent cleaning may be required due
to excessive lint from carpeting, bedding material, etc. It is IMPERATIVE that the unit’s
control compartment, burners, and circulating air passageways BE KEPT CLEAN to
provide for adequate combustion and ventilation air.
Always KEEP the appliance clear and free from combustible materials, gasoline, and
other flammable vapors and liquids.
NEVER OBSTRUCT the flow of combustion and ventilation air. Keep the front of the
appliance CLEAR of all obstacles and materials for servicing and proper operations.
Due to the high temperature, the appliance should be LOCATED out of traffic areas
and away from furniture and draperies. Clothing or flammable material SHOULD NOT
BE PLACED on or near the appliance.
Children and adults should be ALERTED to the hazards of high surface temperature
and should STAY AWAY to avoid burns or clothing ignition. Young children should be
CAREFULLY SUPERVISED when they are in the same room as the appliance.
These units MUST use one of the vent systems described in the Installing the Fireplace
section of the Installers Guide.NO OTHER vent systems or components MAY BE USED.
This gas fireplace and vent assembly MUST be vented directly to the outside and
MUST NEVER be attached to a chimney serving a separate solid fuel burning
appliance. Each gas appliance MUST USE a separate vent system. Common vent
systems are PROHIBITED.
INSPECT the external vent cap on a regular basis to make sure that no debris is
interfering with the air flow.
The glass door assembly MUST be in place and sealed, and the trim door assembly
MUST be in place on the fireplace before the unit can be placed into safe operation.
DO NOT OPERATE this appliance with the glass door removed, cracked, or broken.
Replacement of the glass door should be performed by a licensed or qualified service
person. DO NOT strike or slam the glass door.
The glass door assembly SHALL ONLY be replaced as a complete unit, as supplied
by the gas fireplace manufacturer. NO SUBSTITUTE material may be used.
DO NOT USE abrasive cleaners on the glass door assembly. DO NOT ATTEMPT to
clean the glass door when it is hot.
Turn off the gas before servicing this appliance. It is recommended that a qualified
service technician perform an appliance check-up at the beginning of each heating
season.
Any safety screen or guard removed for servicing must be replaced before operating
this appliance.
DO NOT place furniture or any other combustible household objects within 36
inches of the fireplace front.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!

3
Safety and Warning Information ........................ 2
Service Parts...................................................... 4
Section 1: Approvals and Codes ....................... 6
Appliance Certification .......................................... 6
Installation Codes ................................................. 6
HighAltitude Installations....................................... 6
Section 2: Getting Started ................................. 7
Introducing the Heat-N-Glo Gas Fireplaces........... 7
Pre-installation Preparation................................... 7
Section 3: Installing the Fireplace ................... 9
Constructing the Chase........................................ 9
Step1 Locating the Fireplace............................. 10
Step2 Framing the Fireplace............................. 11
Step 3 Installing the Vent System ....................... 12
A. VentSystemApprovals ....................... 12
B. Installing Vent Components ................ 18
C.VentTermination................................. 23
Step4 Positioning,Leveling,and
Securing the Fireplace............................ 28
Step5 The Gas Control Systems ...................... 28
Step6 The Gas Supply Line .............................. 29
Step7 Gas Pressure Requirements .................. 30
Step8 Wiring the Fireplace................................ 31
Step 9 Finishing ................................................. 32
Step10 Installing Trim, Logs & Ember Material... 34
Installing the Trim................................... 34
Shutter Settings ..................................... 34
Positioning the Logs .............................. 35
Placing the Ember Material .................... 35
Step11 Before Lighting the Fireplace ................. 37
Step12 Lighting the Fireplace............................. 37
AftertheInstallation............................................. 37
Section 4: Maintaining and Servicing
Your Fireplace ............................... 38
Table of
Contents
= Contains updated information.



6
Approval Listings
and Codes Appliance Certification
The Heat-N-Glo fireplace model discussed in this
Installers Guide has been tested to certification
standards and listed by the applicable laboratories.
CERTIFICATION
MODEL LABORATORY TYPE STANDARD
CFX-DIAMOND Underwriters Direct Vent ANSIZ21.88 -2000/
Laboratories Gas Fireplace CSA2.33-M98 •UL307B
Heater
Installation Codes
Thefireplaceinstallationmust conform tolocalcodes.Beforeinstalling the fireplace,
consult the local building code agency to ensure that you are in compliance with all
applicable codes, including permits and inspections.
Intheabsence of local codes,thefireplaceinstallation must conform tothe National
FuelGasCodeANSIZ223.1(intheUnitedStates)ortheCAN/CGA-B149Installation
Codes (in Canada). The appliance must be electrically grounded in accordance
with local codes or, in the absence of local codes with the National Electric Code
ANSI/NFPANo. 70 (in the United States), or to the CSA C22.1 Canadian Electric
Code (in Canada).
These models may be installed in a bedroom or bed-sitting room in the U.S.A. and
Canada.
HighAltitudeInstallations
UL Listed gas fireplaces are tested and approved for elevations from 0 to 2,000
feet in the U.S.A., and from 0 to 4,500 feet in Canada.
Wheninstallingthisfireplaceatanelevationabove2,000feet(intheUnited States),
it may be necessary to decrease the input rating by changing the existing burner
orifice to a smaller size. Input should be reduced four percent (4%) for each 1,000
feet above sea level, unless the heating value of the gas has been reduced, in
which case this general rule will not apply. To identify the proper orifice size, check
with the local gas utility.
When installing this fireplace at an elevation between 2,000 and 4,500 feet (in
Canada), the input rating must be reduced by ten percent (10%).
When installing this fireplace at an elevation above 4,500 feet (in Canada), check
with local authorities.
Consult your local gas utility for assistance in determining the proper orifice for
your location.
Approvals
and Codes
Approvals
and Codes

7
Introducing the
Heat-N-Glo
Fireplaces
Heat-N-Glodirect vent gas fireplaces are designed
to operate with all combustion air siphoned from
outside of the building and all exhaust gases
expelled to the outside.
The information contained in this Installers Guide,
unless noted otherwise, applies to all models and gas
control systems.
Gas fireplace diagrams, including the dimensions, are
shown in this section.
Pre-installation
Preparation This gas fireplace and its components are tested and
safe when installed in accordance with this Installers
Guide. Report to your dealer any parts damaged in
shipment, particularly the condition of the glass.Do
not install any unit with damaged, incomplete, or
substitute parts.
The vent system components are shipped in separate
packages. The gas logs are packaged separately and
must be field installed. Read all of the instructions
before starting the installation. Follow these
instructions carefully during the installation to
ensure maximum safety and benefit. Failure to
follow these instructions will void the owner’s
warranty and may present a fire hazard.
TheHeat-N-Glo Warrantywillbevoidedby, andHeat-
N-Glo disclaims any responsibility for, the following
actions:
• Installationof any damaged fireplace orventsystem
component.
• Modification of the fireplace or direct vent system.
• Installationother thanasinstructedbyHeat-N-Glo.
• Improper positioning of the gas logs or the glass
door.
• Installationand/oruseof any component part not
manufacturedand approvedbyHeat-N-Glo,not
withstandinganyindependent testinglaboratoryor
other party approval of such component part or
accessory.
ANY SUCH ACTION MAY POSSIBLY CAUSE A
FIRE HAZARD.
Getting
Started

8Figure 1. Diagram of the CFX-DIAMOND
When planning a fireplace installation, it’s necessary to determine:
•Where the unit is to be installed.
•The vent system configuration to be used.
•Gas supply piping.
•Electrical wiring.
•Framing and finishing details.
•Whether optional accessories—devices such as a wall switch, or remote
control—are desired.
If the fireplace is to be installed on carpeting or tile, or on any combustible
material other than wood flooring, the fireplace should be installed on a metal or
wood panel that extends the full width and depth of the fireplace.
9 3/4 (248mm)
Ø 8 5/8 (Ø 219mm)
41 7/16 (1053mm)
38
(965mm)
37 7/8
(962mm) 1 7/8
(48mm)
5 9/16
(141mm)
MINIMUM DISTANCE TO HORIZONTAL
COMBUSTIBLE SURFACE (FLOOR, HEARTH, ETC.)
GAS
ACCESS
4 1/2
(114mm)
ELECTRICAL
ACCESS
34 1/2
(876mm)
13 1/2
(344mm)
21 3/4
(552mm)
8 1/2
(219mm)
GAS LINE
ACCESS ELECTRICAL
ACCESS
STANDOFFS
NAILING
TAB
GAS
CONTROLS
RATING PLATE
AND LABELS
NAILING
TAB
NON-COMBUSTIBLE
BOARD
GLASS RETENTION
CLIPS (8)
VENT STARTING
COLLARS

9
Installing the
Fireplace
Constructing the Fireplace Chase
Achaseisaverticalbox-likestructurebuiltto enclose
thegasfireplaceand/oritsventsystem.Verticalvents
that run on the outside of a building may be, but are
not required to be, installed inside a chase.
TREATMENT OF FIRESTOPSPACERSAND CON-
STRUCTION OF THE CHASE MAY VARY WITH
THE TYPE OFBUILDING. THESE INSTRUCTIONS
ARE NOT SUBSTITUTES FOR THE REQUIRE-
MENTS OF LOCAL BUILDING CODES. THERE-
FORE, YOUR LOCAL BUILDING CODES MUST
BE CHECKED TO DETERMINE THE REQUIRE-
MENTS FOR THESE STEPS.
Factory-built fireplace chases should be constructed
in the manner of all outside walls of the home to pre-
ventcoldairdraftingproblems.Thechaseshouldnot
break the outside building envelope in any manner.
Thismeansthat the walls,ceiling,baseplate and can-
tilever floor of the chase should be insulated. Vapor
and air infiltration barriers should be installed in the
chase as per regional codes for the rest of the home.
Additionally, Heat-N-Glo recommends that theinside
surfaces be sheetrocked and taped for maximum air
tightness.
To further prevent drafts, the firestops should be
caulked to seal gaps. Gas line holes and other open-
ings should be caulked or stuffed with insulation. If
the unit is being installed on a cement slab, we rec-
ommendthata layerofplywoodbe placedunderneath
to prevent conducting cold up into the room. Be sure
toincludespark arrestorsforwoodburningunits ifthey
are required.
THE CHASE SHOULD BE CONSTRUCTED SO
THAT ALL CLEARANCES TO THE FIREPLACE
ARE MAINTAINED AS SPECIFIED WITHIN THIS
INSTALLERS GUIDE.
CAUTION:

10
Figure 2. Fireplace Dimensions, Locations,
and Space Requirements for
model CFX-Diamond
Clearance Requirements
The top, back, and sides of the fireplace are defined
bystand-offs.
Minimum Clearances from the Fireplace to
Combustible Materials
Glass Rear of Sides of Top of
Front Floor Fireplace Fireplace Fireplace Ceiling
36 inches 5 9/16” 1/2 inch 1/2 inch 3-1/2 inches 31 inches
(914 mm) (141 mm) (13 mm) (13 mm) (89 mm) (787 mm)
The minimum clearance to a perpendicular wall extending
past the face of the fireplace is 4-inches (102 mm).
Thebackofthefireplacemayberecessed213/4inches
(552 mm) into combustible construction.
A BCD E
42 7/16” 21 3/4” 35 7/8” 71 7/8” 50 7/8”
(1078mm) (552mm) (913mm) (1825mm) (1291mm)
FGHI
40” 20 5/8” 18 5/6” 1/2”
(1015mm) (523mm) (474mm) (13mm)
Step 1
Locating the
Fireplace
The diagram below shows space and clearance
requirements for locating a fireplace within a room.
A
B
E
C
ID
F
G
H

11
Model A B C D*
CFX-DIAMOND 42 7/16” 38 1/2” 21 3/4” 5 9/16”
(1078mm) (978mm) (552mm) (141mm)
Figure 3. FramingDimensions
CAUTION
INTERIOR
WALL
B
AD
CONSTRUCT PLATFORM
WITH 2 X 4 CONSTRUCTION
OR HEAVIER (REQUIRED)
C
FRONT VIEW SIDE VIE
W
* Minimum dimension REQUIRED
!
WARNING: THECFX-DIAMOND REQUIRES
AN ELEVATED PLATFORM CONSTRUC-
TION TO ACCOMMODATE THE DIAMOND
SHAPED SURROUND WHICH IS LARGER
THAN THE FIREPLACE (SEE FIGURE 1)
Minimum Clearances from the Vent Pipe to Combustible Materials
For Vertical
For Horizontal Sections Sections AtWallFirestops
Top Bottom Sides Top Bottom Sides
3 inches* 1 inch 1 inch 1 inch 2-1/2 inches 1/2 inch 1 inch
(75 mm) (25 mm) (25 mm) (25 mm) (63.7 mm) (13 mm) (25 mm)
For minimum clearances, see the direct vent
termination clearance diagrams on pages 25 and
27 in this section.
Additional clearance and/or installation of a heat
shield is required above the first 90° elbow. See
page 19 of the Installers Guide.
Step 2
Framing the
Fireplace
Fireplace framing can be built before or after the
fireplace is set in place. Framing should be
positioned to accommodate wall coverings and
fireplace facing material. The diagram below shows
framing reference dimensions.
MEASURE FIREPLACE DIMENSIONS, AND
VERIFY FRAMING METHODS AND WALL
COVERING DETAILS BEFORE FRAMING
CONSTRUCTION BEGINS.
*

12
Vent system components
Vent system
termination kits
Figure 4. Vent Components and Terminations
Step 3
Installing the
Vent System
A. VentSystem Approvals
This model is approved to use D-Series components
and terminations. Approved vent system components
are labeled for identification. NO OTHER VENTING
SYSTEM OR COMPONENTS MAY BE USED.
Detailed installation instructions are included with each
vent termination kit and should be used in conjunction
with this Installers Guide. The drawing below shows
vent system components and terminations.
The flame and ember appearance may vary based on
thetypeof fuelburnedandthe venting configurationused.
Identifying Vent Components
The vent systems installed on this gas fireplace may
include one, two, or three 90oelbow assemblies. The
relationships of vertical rise to horizontal run in vent
configurations using 90oelbows MUST BE strictly
adhered to. The rise to run relationship are shown in the
venting drawings and tables. Refer to the diagrams on
the next several pages.
NOTE: TWO 45OELBOWS MAY BE USED IN PLACE
OF ONE 90OELBOW. RISE TO RUN RATIOS IN
THE VENT SYSTEM MUST BE FOLLOWED IF 45O
ELBOWS ARE USED.
DVK-TVCD
DVK-01TRD
DVK-01D
VERTICAL
TERMINATION
HORIZONTAL
TERMINATION
WALL FIRESTOP
90 DEGREE ELBOW CEILING FIRESTOP
WALL BRACKET
PIPE LENGTH
HORIZONTAL PIPE SUPPORT
ROOF FLASHING
STORM COLLAR
HEAT SHIELD

13
Figure 5. D-Series Direct Vent Component Specifications
(5-inch inner pipe / 8 5/8-inch outer pipe)
NOTE: PIPES OVERLAP 1-3/8 INCHES (34.93 mm) AT EACHJOINT.
DV-36D
5 3/4”
(146mm)
8 3/4”
(222mm)
11 3/4”
(298mm)
DV-12D DV-09D DV-06D
DV-48D
DV-90D
73/8”
(187mm)
65/32”
(156mm)
115/8”
(295mm)
1115/16”
(303mm)
57/8”
(149mm)
8 5/8”
(220mm)
81/2”
(216mm)
67/16”
(164mm)
DV-45D
111/16”
(281mm)61/2”
(165mm)
81/2”
(216mm)
51/16”
(129mm)
85/8”
(220mm)
35 3/4”
(908mm)
47 3/4”
(1.2m)

14
VERTICALVENTING
V (FT.)
46’ MAX. (14M)
Figure 6. Vertical Venting
V
CAP
For vertical venting greater than V=12 ft. (without any
elbows installed), SRV593-170 vertical baffle kit may be
installed for improved performance. Follow instructions
provided with the kit.

15
VENTING WITH ONE (1) 90° ELBOWS
V(FT.) H (FT.)
0’ 3’ MAX. (.91m)
3' MIN. (914 mm) 9' MAX.(2.7m)
4' MIN. (1.2m) 12' MAX. (3.7m)
5' MIN. (1.6m) 15'MAX. (4.6m)
6' MIN. (1.9m) 18'MAX. (5.5m)
V + H = 30’ MAX. (9.3 m)
Ratio V to H = 1:3
Figure 7. Venting with One 90° Elbow
H = 20' MAX. (6.2m)
NOTE: SRV570-290 Heat Shield is required above
first elbow if clearance is less than 4 inches
(102mm) (See Figure 12).
H
V

16
VENTING WITH TWO (2) 90° ELBOWS
V(FT.) H+H1(FT.)
3' MIN. (914mm) 9' MAX. (2.7m)
4' MIN. (1.2m) 12' MAX. (3.7m)
5' MIN. (1.6m) 15' MAX. (4.6m)
6' MIN. (1.9m) 18' MAX. (5.5m)
V + H + H1= 30’ MAX. (9.3 m)
Ratio V to H + H1= 1:3
Figure 8. Venting with two 90° elbows
VENTING WITH TWO (2) 90° ELBOWS
V(FT.) H (FT.)
3' MIN. (914 mm) 9' MAX.(2.7m)
4' MIN. (1.2m) 12' MAX. (3.7m)
5' MIN. (1.6m) 15'MAX. (4.6m)
6' MIN. (1.9m) 18'MAX. (5.5m)
V + V1+ H1= 30’ MAX. (9.3 m)
Ratio V to H = 1:2
H = 20' MAX. (6.2m)
H = 20' MAX. (6.2m)
NOTE: SRV570-290 Heat
Shield is required above
first elbow if clearance
is less than 4 inches
(102mm).
H
1
H
V
H
V
V
1

17
Figure 9. Venting with three 90° elbows
VENTINGWITH THREE (3) 90° ELBOWS
V(FT.) H+H1(FT.)
3' MINIMUM (914 mm) 6' MAXIMUM(1.9m)
4' MINIMUM (1.2 m) 8' MAXIMUM(2.4 m)
5' MINIMUM (1.6 m) 10' MAXIMUM(3.1m)
RATIOV TO H = 1:2
V + V1+ H + H1= 30’ MAXIMUM (9.3m)
H + H1= 20’ MAXIMUM (6.2m)
H= 10’ MAXIMUM (3.1m)
VENTINGWITH THREE (3) 90°ELBOWS
V(FT.) H + H1(FT.)
3' MINIMUM (914 mm) 6' MAXIMUM(1.9m)
4' MINIMUM (1.2 m) 8' MAXIMUM(2.4 m)
5' MINIMUM (1.6 m) 10'MAXIMUM(3.1m)
6' MINIMUM (1.9 m) 12'MAXIMUM(3.6m)
V + V1+ H + H1= 30’ MAXIMUM (9.3 m)
H + H1= 20’ MAXIMUM (6.2 m)
RATIO V TO H + H1= 1:2
NOTE: SRV570-290 Heat
Shield is required above
first elbow if clearance
is less than 4 inches
(102mm).
H
1
H
V
1
V
V
1
H
1
H
V

18
B. Installing Vent Components
1. Attachthe FirstVentComponent totheStarting Collars
• Apply a 3/8 inch (9.5 mm) bead of stove cement
aroundtheinnerpipe fireplace starting collar.
• Makesurethatthefireplaceropegasketsupplied
with the fireplace seals between the first 8-5/8 inch
(219mm) vent component and the fireplace top.
• Lock the vent components into place by sliding the
concentric pipe sections with four (4) equally
spaced interior beads into the fireplace collar or
previously installed component end with four (4)
equally spaced indented sections.
• When the internal beads of each outer pipe line up,
rotate the pipe section clockwise about one-quarter
(1/4) turn. The vent pipe is now locked together.
1. Apply the stove ce-
ment.
2. Line up the internal
beads and rotate the
pipe sections clock-
wise until locked.
3. Lock the vent compo-
nents into place.
4. Check the seal on the
rope gasket.
Figure 10. Attaching the First Vent Component to
the Starting Collars
WARNING: A3/8 INCH (9.5 MM) BEAD OF
STOVE CEMENT MUST BE PLACED
AROUND THE INNER PIPE FIREPLACE
STARTINGCOLLARBEFOREATTACHING
THE FIRST VENT COMPONENT.
FAILURE TO SEAL THIS JOINT MAY
CAUSE THE FIREPLACE TO OPERATE
IMPROPERLY. SEE FIGURE 10.
WARNING: ENSURE THAT THE
FIBERGLASS ROPE GASKET SUPPLIED
WITH THE FIREPLACE SEALS BETWEEN
THE FIRST VENT COMPONENT AND
THE FIREPLACE TOP.
3/8”
(9.5 mm)
!
!
STARTING
COLLAR
STOVE
SEALANT
BEAD
1 INCH
(25.4mm)
FIRST VENT
COMPONENT

19
!
2. Continue Adding Vent Components
To continue adding vent components in accordance
with the pre-planned vent system configuration:
• Ensure that each
succeeding vent
component is securely
fitted and locked into
the preceding compo-
nent in the vent sys-
tem.
Continue adding vent
components, locking
each succeeding
component into place.
Figure 11. Adding Venting Components
90° elbows may be installed and rotated to any point
around the preceding component’s vertical axis. If an
elbow does not end up in a locked position with the
preceding component,
attach with a minimum of two
(2) sheet metal screws.
WARNING: MODEL CFX-DIAMOND
REQUIRES SHIELD SRV570-290 ABOVE
THE FIRST 90° ELBOW IN THE SYSTEM
IF CLEARANCE IS LESS THAN 4 INCHES
(102MM). SEE INSTALLATION SHEET AND
HEAT SHIELD SUPPLIED WITH FIREPLACE.
Figure 12. Placement of SRV570-290 Heat Shield
First 900elbow in system.
DIRECTION
UP
HEAT SHIELD
COMBUSTIBLE
SURFACE
90 ELBOW
0
DIRECTION
UP
HEAT SHIELD
COMBUSTIBLE
SURFACE
90 ELBOW
0
CORRECT
INCORRECT
HEAT SHIELD
COMBUSTIBLE
SURFACE 3” MIN.
(76mm)

20
3. Install Support Brackets
For Horizontal Runs - The vent system must be
supported every five (5) feet of horizontal run by a
horizontal pipe support.
To install support brack-
ets for horizontal runs:
• Place the pipe sup-
ports around the vent
pipe.
• Nail the pipe supports
to the framing mem-
bers.
For Vertical Runs -
The vent system must
be supported every
eight (8) feet (2.4 m)
abovethe fireplace flue
outlet by wall brackets.
To install support brackets
forverticalruns:
• Attach wall brackets
to the vent pipe and
secure the wall
bracket to the framing
members with nails
or screws.
Use wall brackets to
support vertical runs
every 8 feet (2.4 m)
above the fireplace flue
outlet.
Figure 13.Installing Support Brackets
4. Install Firestops
For Horizontal Runs - Firestops are REQUIRED
on both sides of a combustible wall through which
the vent passes.
NOTE Model DVK-01TRD does not need an exterior
firestop on an exterior combustible wall.
To install firestops for horizontal runs that pass
through either interior or exterior walls:
• Cut a 12-inch by 12-inch (305mm X 305mm)
hole through the wall. The center of the hole is
one (1) inch (25.4 mm) above the center of the
horizontal vent pipe.
WALL BRACKETS
WALL
STUD
8 ft.
(2.4m)
FLUE
OUTLET
1 INCH MIN.
(25mm)

21
• Position the firestops on both sides of the hole
previously cut and secure the firestops with nails
or screws.
• The heat shields of the firestops MUST BE
placed towards the top of the hole.
• Continue the vent run through the firestops.
1. Cut the hole through
the wall.
Figure 14. Hole and Vent Pipe
2. Position the firestops.
3. Place the heat shield
to the top.
4. Continue the vent run.
Figure 15. Heat Shield, Interior & Exterior Firestops
For Vertical Runs - One ceiling firestop is REQUIRED
atthehole in eachceilingthroughwhich the ventpasses.
To install firestops for vertical runs that pass through
ceilings:
• Position a plumb bob directly over the center of the
vertical vent component.
• Mark the ceiling to establish the centerpoint of the
vent.
TRIM HEAT
SHIELD IF TOO
LONG, ADD TO
SHIELD IF TOO
SHORT
EXTERIOR
FIRESTOP
INTERIOR
FIRESTOP
HEAT SHIELD
V
ENT PIPE
1" (25.4 mm)
12"
(305mm)
12"
(305mm)
NOTE: There must be NO INSULATION or other
combustibles inside the framed firestop opening.

22
Figure 17.Ceiling Firestop (Ceiling Side)
Figure 16.Hole and New Framing Members
If the area above the ceiling is NOT an attic,
position and secure the ceiling firestop on the
ceiling side of the previously cut and framed hole.
This shows a ceiling
installation.
• Drill a hole or drive a nail through this centerpoint.
• Check the floor above for any obstructions, such
as wiring or plumbing runs.
• Reposition the fireplace and vent system, if
necessary, to accommodate the ceiling joists
and/or obstructions.
• Cut a 11-inch X 11-inch (280 mm X 280 mm)
hole through the ceiling, using the centerpoint
previously marked.
• Frame the hole with framing lumber the same
size as the ceiling joists.
1. Cut the ceiling hole.
2.Add the new framing
members.
JOIST
CEILING FIRESTOP
CEILING
NAILS (4 REQUIRED)
CEILING
NEW
FRAMING
MEMBERS
EXISTING CEILING
JOISTS
CHIMNEY
HOLE
11" (280 mm) 11" (280mm)
NOTE: There must be NO INSULATION or other
combustibles inside the framed firestop opening.