Heatrae Sadia Multipoint 10 and 15 litre User manual

Multipoint 10 and 15 litre
Fitting Instructions

 This product can be used by children aged from 8 years and above and
persons with reduced physical sensory or mental capabilities or lack
of experience and knowledge if they have been given supervision or
instruction concerning use of the product in a safe way and understand
the hazards involved. Children shall not play with the product. Cleaning
and user maintenance shall not be made by children without supervision.
Children must be supervised to ensure they do not play with the product.
The HWA Charter Statement requires that all members adhere to the following:
`To supply t for purpose products clearly and honestly described.
`To supply products that meet, or exceed appropriate standards and building and water regulations.
`To provide pre and post sales technical support.
`To provide clear and concise warranty details to customers.
Contents
1. Introduction..................................................3
1.1 General ..................................................3
1.2 Symbols used.........................................3
1.3 Abbreviations..........................................3
1.4 Liabilities ................................................3
2. Safety............................................................4
2.1 General safety warnings ........................4
2.2 Recommendations .................................4
2.3 Specic safety instructions.....................4
3. Technical specication ...............................5
3.1 Technical data ........................................5
3.2 Dimensions and connections .................5
3.3 Electrical diagram(s) ..............................5
4. Description of the product..........................6
4.1 General description ................................6
4.2 Operation principle .................................6
4.3 Standard delivery ...................................6
4.4 Mains connections .................................6
5. Before installation .......................................7
5.1 Installation regulations ...........................7
5.2 Installation requirements ........................7
5.3 Choice of location...................................7
6. Installation....................................................8
6.1 General ..................................................8
6.2 Water connections..................................8
6.3 Electrical connections ............................9
7. Commissioning............................................10
7.1 General ..................................................10
7.2 Checklist before commissioning.............10
7.3 Commissioning procedure .....................10
8. Operation......................................................11
8.1 General ..................................................11
9. Maintenance.................................................12
9.1 General ..................................................12
9.2 Standard inspection & maintenance
operations ............................................. 12
10. Troubleshooting........................................13
10.1 Fault nding..........................................13
11. Decommissioning procedure ..................14
12. Spare parts................................................14
Accessories......................................................15
Warranty ...........................................................15

3
1. Introduction
1.1 General
The following instructions are offered as a guide to
the user and installer.
The installation must be carried out by a competent
plumbing and electrical installer in accordance
with Building Regulation G3 (England and Wales),
Technical Standard P3 (Scotland) or Building
Regulation P5 (Northern Ireland) and the Water
Fitting Regulations (England and Wales) or Water
Byelaws (Scotland).
1.2 Symbols used
In these instructions, various risk levels are employed
to draw the user’s attention to particular information.
In doing so we wish to safeguard the user, avoid
hazards and guarantee the correct operation of the
appliance.
WARNING
Risk of dangerous situation causing slight
physical injury.
DANGER
Risk of dangerous situation causing slight
physical injury.
CAUTION
Risk of material damage.
Signals important information.
1.3 Abbreviations
`RCD – Residual current device
`MCB – Miniature circuit breaker
1.4 Liabilities
Manufacturer’s liability
Our products are manufactured in compliance with
the requirements of the various applicable European
Directives.
This product complies with the requirements of the
CE marking directive.
In the interest of UK customers, we are continuously
endeavouring to make improvements in product
quality. All the specications stated in this document
are therefore subject to change without notice.
Our liability as the manufacturer may not be invoked
in the following cases:
`Failure to abide by the instructions on using the
product.
`Faulty or insufcient maintenance of the product.
`Failure to abide by the instructions on installing
the product.
Installer's liability
The installer is responsible for the installation and
the commissioning of the product. The installer must
respect the following instructions:
`Read and follow the instructions given in the
manuals provided with the product.
`Carry out installation in compliance with the
prevailing legislation and standards.
`Perform the initial start-up and carry out any
checks necessary.
`Complete the commissioning checklist.
`Explain the installation to the user.
`If maintenance is necessary, warn the user of
the obligation to check the product and maintain
it in good working order.
`Give the instruction manual to the user.
User’s liability
To guarantee optimum operation of the product, the
user must respect the following instructions:
`Read and follow the instructions given in the
manuals provided with the product.
`Call on qualied professionals to carry out
installation and initial start-up.
`Get your tter to explain your installation to you.
`Have your required checks and services done.
`Keep the instruction manuals in good condition
and close to the product.

4
2.3 Specic safety instructions
WARNING
DO NOT operate the product if:
`Water ceases to ow during use.
`Water has entered inside the
product because of an incorrectly
tted cover.
`If the appliance is damaged.
(in all cases turn off mains power and
isolate water supply)
`If water discharges from the
temperature/pressure relief valve
on the product shut down. Do not
turn off any water supply. Contact
a competent installer for unvented
water heaters to check the system.
`Do not tamper with any of the
safety valves tted to the system.
If a fault is suspected contact a
competent installer.
`DO NOT bypass the thermal cut-
out in any circumstance.
2. Safety
2.1 General safety warnings
DANGER
This product is unvented and as such
becomes pressurised when in operation.
The combination of pressurisation and hot
water could lead to serious physical injury
if the safety instructions in this manual are
not adhered to.
DANGER
Do not install where the unit may freeze.
WARNING
`Only competent persons having
received adequate training are
permitted to work on the product
and the installation.
`Do not tamper with the safety
valve supplied.
`Before any work, switch off the
mains supply to the appliance.
`Do not switch on if there is a
possibility that the water in the
appliance is frozen.
CAUTION
Do not operate immersion heater until the
product has been lled with water.
2.2 Recommendations
CAUTION
`Annual maintenance is
recommended by a competent
person.

5
3.3 Electrical diagram(s)
3. Technical specication
3.1 Technical data
Supplier’s name or trade mark Multipoint
Supplier’s model identier 10L (3kW) 10L (4.5kW) 15L (3kW) 15L (4.5kW)
Storage volume V in litres 10.0 10.0 15.0 15.0
Mixed water at 40°C V40 in litres 19 19 27 27
The declared load prole XXS XXS XXS XXS
The water heating energy efciency class of the model CCCC
The water heating energy efciency in % 30.9 30.9 29.6 29.6
The annual electricity consumption in kWh 596 596 622 622
Daily fuel consumption in kWh 2.900 2.900 3.050 3.050
The thermostat temperature settings of the water heater, as
placed on the market by the supplier 60°C
Specic precautions that shall be taken when the water heater
is assembled, installed or maintained and disposed of at end
of life
See Section 3 - 11
Electrical rating 3kW@240V~/2.75kW@230V~
4.5kW@240V~/4.1kW@230V~
Capacities 10 or 15 litres
Weight (full) 10 litre - 16.9kg 15 litre - 23.8kg
Rated pressure 0.6MPa (6 bar)
Minimum recommended supply pressure 0.08MPa (0.8 bar)
Maximum supply pressure to PRV 1.6MPa (16.0 bar)
Temperature/Pressure Relief Valve 90°C/0.7MPa (7 bar)
3.2 Dimensions and connections
Reset
button
Reset
button
Combined
thermostat
and thermal
cut-out
Combined
thermostat
and thermal
cut-out
Element
(’stat / cut-out plugs
directly into element
terminations)
Neon
Neon
Earth
Post
Earth
Post
Element
N L
NL
Dimension10 litre 15 litre
A
B
C
D
457613
572
500
350
728
656
506
Top
view
267
100
12.5
A
B
C
D
190
Fixing centres
of mounting
bracket
252
171
59
Front view Side view
Figure 2 – 3kW model
Figure 3 – 4.5kW modelFigure 1
Table: Technical parameters in accordance with European Commision regulations 814/2013
and 812/2013

6
4.2 Operation principle
The product is used to heat and store hot water for
use in domestic applications.
4.3 Standard delivery
`Product
`Fixing bracket
`Screw pack
`Instructions
4.4 Mains connections
See gure 4-6 below.
4. Description of the product
4.1 General description
This product is a purposed designed unvented water
heater. The product has a copper inner vessel,
which ensures an excellent standard of corrosion
resistance. The outer casing is a combination of
resilient thermoplastic moldings and painted steel.
The product is supplied complete with all the necessary
safety and control devices needed to allow connection
to the cold water mains. These components are preset
and should not be tampered with.
Temperature
and pressure
relief valve
Temperature
and pressure
relief valve
Pressure
relief
(expansion)
valve
Note: If pressure reducing valve is
used expansion down the mains is not possible
Pressure
relief
(expansion)
valve
Pressure
relief
(expansion)
valve
Expansion
vessel
Expansion
vessel
Service valve
Service valve
Hot Cold
Hot Cold
Check
Valve
Check
Valve
Check
Valve
Nearest cold
draw off
Nearest cold
draw off
Nearest cold
draw off
Service valve
(fixed jumper or
1/4 turn ball type)
Cold
water
mains
Cold
water
mains
Cold
water
mains
Tundish
Tundish
Tundish
Multipoint
10 litre
or 15 litre
heater
Multipoint
10 litre
or 15 litre
heater
Temperature
and pressure
relief valve
Hot Cold
Multipoint
10 litre
or 15 litre
heater
To drain (waste)
To drain (waste)
To drain (waste)
2.8 (10 l) or 4.2 (15 l)
metres is required for
expansion in pipework
Figure 4 – For inlet pressure up to 0.41 MPa (4.1 bar)
Figure 5 – For inlet pressure up to 0.41 MPa (4.1 bar)
where expansion in mains supply is not possible
Figure 6 – For inlet pressure above 0.41 MPa (4.1 bar)

7
5.3 Choice of location
`National Wiring rules may contain restrictions
concerning the installation of these products in
bathrooms.
`The product should be vertically wall mounted
using the wall bracket supplied. The water
connections must always be to the top of the
product.
`Enough space should be left at the top above
the product for pipe connections and access to
the Temperature/Pressure Relief Valve. Refer to
gure 1 and the Dimensions Table to determine
a suitable position for the product.
WARNING
Ensure that the wall can support the full
weight of the product (see Technical
specications) and that there are no
hidden services (electricity, gas, or water)
below the surface of the wall.
5. Before installation
5.1 Installation regulations
WARNING
Installation of the product must be carried
out by a qualied engineer in accordance
with prevailing and national regulations as
listed below.
`Building Regulations
`The Building Standards (Scotland)
`The Building Regulations
(Northern Ireland)
`I.E.E Electrical Regs
`UK Water Regulations
5.2 Installation requirements
Water supply
In an unvented system the pressure and owrate is
directly related to the incoming water supply. For this
reason it is recommended that the maximum water
demand is assessed and the water supply checked
to ensure this demand can be satisfactorily met.
`We suggest the minimum supply requirements
should be 0.08MPa (0.8 bar) pressure.
`A 15mm cold water supply is recommended.
`The higher the available pressure and ow rate
the better the system performance.
`The water supply must be of wholesome water
quality (Fluid Category 1 as dened by the Water
Supply Regulations 1999).
Outlet/terminal ttings (taps,etc.)
`The product can be used with most types of
terminal ttings.
`All ttings, pipework and connections must have
a rated pressure of at least 8 bar at 80°C.

8
WARNING
Failure to provide adequate pressure relief
will invalidate any guarantee and lead to a
dangerous installation.
`Expansion can take place within the cold water
supply provided that both :
• Backow in the main is not prevented by any
stop valve with loose jumper, check valve,
pressure reducing valve or similar, and
• Hot water expansion does not enter a branch
to a cold water outlet (see Figure 02 for
expansion pipe lengths).
Both the above conditions must be met.
Additionally expansion within the cold water
supply will not be possible if the static supply
pressure exceeds 0.41 MPa (4.1bar).
`If any of the conditions in above cannot be met,
expansion must be accommodated using an
Expansion Vessel. To ensure all expansion takes
place in the vessel a Check Valve must also
be tted together with a Pressure (expansion)
Relief Valve (see Figure 03). Use Accessory
Pack U2 code no. 95 970 351.
`If the static supply pressure exceeds 0.41 MPa
(4.1 bar) a Pressure Reducing Valve must be
tted to the cold main supply. If a Pressure
Reducing Valve is used, an Expansion Vessel
must also be used (see Figure 04). Use
Accessory Packs U1 and U2 Code No.’s 95 970
352 and 95 970 351.
Discharge
`The discharge outlet from the Pressure
(expansion) Relief Valve and the Temperature/
Pressure relief Valve must be connected to
a discharge pipe. It is recommended that the
tundish supplied be installed in the discharge
pipe to give a visible indication that the valves
are operating.
`The discharge pipe must fall continuously from
the valve outlets and be unobstructed, and in a
frost-free environment.
`The pipe from the valves to the tundish should
be 15mm o/dia minimum. From the tundish to
the point of discharge the pipe should be 22mm
o/dia minimum and have a resistance to ow
equivalent to 9 metres of straight pipe. Long
discharge pipe runs should have an increased
internal diameter.
`The water may drip from the discharge pipe of
6. Installation
6.1 General
After reading the previous sections in this booklet
and choosing a good location for the product please
install, paying attention to the following hydraulic,
electrical and commissioning sections.
6.2 Water connections
WARNING
`Under no circumstances should
the factory tted temperature/
pressure relief valve be removed
other than a competent person. To
do so will invalidate any guarantee
or claim.
`No control or safety valve should
be tampered with or used for any
other purpose.
`The discharge pipe should not
be blocked or used for any other
purpose.
`The tundish should not be
located adjacent to any electrical
components.
Refer to the Installation schematic (gure 4-6, page
6) to determine which valves and accessories are
required.
Plumb in the valves in the sequence shown in the
relevant gures 4-6, page 6.
`The water connections are 15mm diameter
copper tubes suitable for compression ttings.
Do not use solder joints as this will damage
the heater and may prevent servicing under
warranty.
`The INLET is marked BLUE, the OUTLET is
marked RED. The WRAS listed isolating valve
(supplied) must be tted on the cold water
supply to the product. Several hot outlets can
be served.
`Plumbers Paste must not be used as it can
impair the operation of the valves.
`The product MUST be tted with a Pressure
Relief Valve. The factory tted Temperature/
Pressure Relief Valve can full this function.

9
the pressure relief device and that this pipe must
be left open to the atmosphere. The pressure
relief device is to be operated regularly to
remove lime deposits and to verify that it is not
blocked.
`The pipe material should be capable of
conveying water/steam at 100°C.
`The nal discharge point should be in a safe,
visible position.
6.3 Electrical connections
WARNING
`Disconnect from the mains
electrical supply before removing
any covers.
`This product must be earthed. It is
suitable for a.c. supply only.
`Disconnect the electrical supply
before removing the terminal
cover.
`Installation must be in accordance
with the current I.E.E. Wiring
Regulations.
`The product is supplied tted with a 0.75m 3
core 1.5mm2 exible cable on the 3kW model
or a 0.75m 3 core 2.5mm2cable on the 4.5kW
model. The electricity supply should be fused 13
Amp for a 3kW model and 20 Amp for a 4.5kW
model and be via a double pole isolating switch
with a contact separation of at least 3mm in both
poles. Refer to the schematic wiring diagrams
below.
The wires are colour coded as follows:
Green and Yellow EARTH
Brown LIVE (L)
Blue NEUTRAL (N)

10
`Setting the “mid-range” position:
Rotate the thermostat knob to the mid position.
Remove the terminal cover by using a large
at bladed screwdriver to depress the three
snap lugs located in the three top rectangular
depressions. Holding the thermostat knob in
position turn the terminal cover over and remove
the backing disc from the underside of the cover.
Turn the backing disc over and ret to the knob
ensuring the notch locates with the boss on the
underside of the cover. Ret the terminal cover,
the thermostat will now be locked in the “mid-
range” position.
`Setting the “hot” position:
Rotate the thermostat knob to mid way through
the hot graduated range (red graphic). Follow
the procedure detailed above, however in
this case the knob should be held in the “hot”
position previously set. When the terminal cover
has been retted the thermostat will be locked in
the “hot” position. This position is recommended
when using the heater in conjunction with a
thermostatic blending valve.
`Water may drip from the discharge pipe of the
pressure relief device - this pipe must be left
open to atmosphere.
7. Commissioning
7.1 General
After lling the installation with water in the previous
section please follow the following steps to complete
the installation of the product.
WARNING
DO NOT switch on the product until it has
been lled with water.
7.2 Checklist before commissioning
`Check all water connections for leaks and rectify
as necessary.
`Check that all installation, electrical and
discharge pipe requirements have been met.
`Check that electrical connections are tight.
7.3 Commissioning procedure
`Open a hot water tap, turn on mains water
supply to the product.
`Allow product to ll and leave hot tap running
for a short while to purge any air and ush out
the pipework. Close the hot tap and check the
system for leaks.
`Manually test the operation of the Temperature/
Pressure Relief Valve and, if tted, the Pressure
(expansion) Relief Valve. Ensure water ows
freely from the valve(s) and through the
discharge pipes.
`Switch on the electrical supply. The indicator
light will illuminate during heating. When the set
temperature is reached, the indicator light will go
out.
`The set temperature can be adjusted by rotating
the knob located in the terminal cover. It is
possible to lock the thermostat knob in either
the mid-range or a “hot” position by following
the procedures. Always switch off the electrical
supply before removing the terminal cover.

11
System malfunction
`Explain how to isolate electrical and water
supplies in case of a fault.
`Explain that a qualied plumber and/or
electrician should be contacted if there is a fault.
`Explain how to identify/check basic faults.
Maintenance
`Explain the necessity to carry out regular
maintenance of the product to ensure its
continued safe and efcient operation.
Literature
Hand over the Installation and user instructions.
`The product stores water at the temperature set
on the adjustable thermostat. This can be set to
give temperatures in the range of 10 to 70°C. To
avoid any risk of freezing when the product is not
in use for long periods during the winter months,
do not switch off the electrical supply and set the
thermostat to its minimum position. N.b. this will
not protect other system pipework.
`The thermostat can also be locked in either the
mid range or a “hot” (recommended when using
in conjunction with a Thermostatic Blending
Valve) position. To lock the thermostat position,
the instructions given under Sections 4.2.3
or 4.2.4 should be followed. We recommend
that this procedure is carried out by a qualied
electrician.
`The indicator light will be illuminated when the
product is heating.
8. Operation
8.1 General
WARNING
`Do not block or restrict the
discharge from any safety valve
tted.
`Do not tamper with any safety
valve tted.
`If water discharges from any
safety valve tted, switch off the
electrical supply to the product
immediately. Contact the Heatrae
Sadia Service Team (Tel: 0844
8711535) or an approved installer.
Do not turn the electrical supply
on again until the product has
been checked and approved by a
qualied installer.
Following Installation and Commissioning of the
product, the operation should be fully explained to
the user.
Hot water
`Indicate the location of the product and identify
the outlets to which it is connected.
`Explain that the temperature is set upon
installation and conrm the temperature which
the water is set at.

12
9. Maintenance
9.1 General
Maintenance requirements
Unvented hot water systems have a continuing
maintenance requirement in order to ensure safe
working and optimum performance. It is essential that
the relief valve is periodically inspected and manually
opened to ensure no blockage has occurred in the
valves or discharge pipework. Maintenance of this
appliance should only be carried out by a suitably
qualied person. Failure to do so could invalidate the
warranty.
WARNING
Disconnect from all electrical supplies
before beginning any work on the product.
Water contained within the product may
be very hot!
Maintenance should be carried out by a
competent person and any replacement
parts should be authorised Heatrae Sadia
spare parts.
It is recommended that maintenance is
carried out annually and should include
the checks detailed in the sections below.
Little maintenance is required, however in
hard water areas the product will require
periodic descaling to ensure efcient
operation.
9.2 Standard inspection & maintenance
operations
To descale:
`Switch off and disconnect the electrical supply.
Turn off the water supply to the product.
`Open a hot tap to relieve any system pressure.
Disconnect the plumbing connections to the
product and remove from the wall bracket (note
full weights of product). Empty the product
through the outlet connection.
`Remove the terminal cover by using a large at
bladed screwdriver to depress the 3 snap lugs
located in the top 3 rectangular depressions.
`Remove the insulating pad from the terminal
housing. Disconnect the electrical terminations
to the thermostat. Disconnect earth links to the
earthing stud.
`Remove the element plate assembly by
unscrewing the ve securing screws, a tapped
jacking point is provided. Remove any loose
scale from the container. Carefully clean off any
scale from the element and thermostat pocket.
DO NOT clean scale from interior container
walls.
`Re-assemble the element plate assembly
tting a new sealing gasket. Note the correct
orientation of the element plate by reference
to Figure 07 below. Rewire the product with
reference to the Wiring Diagrams. Ret the
insulating pad to ensure the correct operation of
the thermostat.
Outlet
Cable
clamp
Inlet
Inlet
Earth
post
Earth
post
Thermostat
securing
post
Front
Front
Cable
clamp
Combined
thermostat
and thermal
cut-out
Temperature /
pressure
relief valve
Temperature /
pressure
relief valve
Combined
thermostat
and thermal
cut-out
Outlet
`Re-commission the product following the
Installation and Commissioning instructions.
`The Temperature/Pressure Relief Valve and,
if tted, the Pressure (expansion) Relief Valve
should be regularly checked. This is to remove
limescale deposits and to verify that it is not
blocked. To check the valves:
Manually operate the valves by either twisting
the cap or lifting the lever. Ensure water
ows freely from the valve(s) and through the
discharge pipes. Ensure the valve(s) reseat
correctly when released.
`The Expansion Vessel, if tted, should have a
pre-charge pressure of 0.41 MPa (4.1 bar). This
can reduce over time and eventually require re-
charging. To do this:
`Turn off water supply to the product; open a hot
tap to relieve system pressure.
`Remove dust cap from top of Expansion Vessel
`Check pre-charge pressure using a tyre
pressure gauge. If the pressure is lower than
0.41 Mpa (4.1 bar) it should be recharged using
a tyre pump (Schraeder Valve type). DO NOT
OVER CHARGE.
`Re-check pressure and when correct replace
dust cap.
`Turn on mains water supply and close hot tap.
Figure 7 – 3kW model
Figure 7 – 4.5kW model

13
10.1 Fault nding
Disconnect the electrical supply before removing the
terminal cover. It is recommended that any service
operations on the product are carried out by a
competent person.
10. Troubleshooting
WARNING
Do not tamper with any of the safety valves
or controls supplied with the cylinder as
this will invalidate any guarantee
Symptom Possible cause Remedy
Water not heating A. Electrical supply fault A. Check electrical supply
B. Thermal cut-out tripped B. Check cut-out, if operated reset and check
thermostat operation. If necessary replace
thermostat/thermal cut-out (see wiring diagram)
C. Thermostat fault C. Check thermostat operation. Replace if
necessary
Discharge of water
from pressure relief
valve (continuously)
Excessive mains water pressure Fit Pressure reducing valve Pack U1 and U2
(see important installation points)
Discharge of water
from Pressure relief
valve (intermittently)
A. Expansion in mains not
possible
A. Fit pack U2 (see important installation points)
B. Mains pressure exceeds 0.41
MPa (4.1 bar)
B. Fit packs U1 and U2
C. Pack U1 tted without pack U2 C. Fit pack U2 when using pack U1
D. Pressure relief valve fault D. Replace pressure relief valve
E. Loss of pressure from
expansion vessel
E. Check and if necessary re-charge Expansion
vessel pre-charge pressure (see section 9)
Discharge of water
from Temperature /
pressure relief and/
or water/steam from
pressure relief valve
Thermostat and thermal cut-out
fault
Replace thermostats and thermal cut-outs
No water ow A. Inlet vales incorrectly tted A. Check all vales are correctly installed in
accordance with ow direction arrows
B. Mains water supply not turned
on
B. Check mains water supply is on
C. Blockage in mains water
supply
C. Check for obstructions. If pack U1 is tted
check the strainer is not blocked
'Milky water' Oxygenated water Water from a pressurised system releases
oxygen bubbles when owing. The milkiness will
disappear after a short while

14
12. Spare parts
The following comprehensive list of spare parts is
available for your product. Please refer to the Rating
Label on the side of your product before ordering to
ensure the correct spare part is obtained.
Do not replace with parts not recommended by
Heatrae Sadia - this will invalidate your warranty and
may render the installation dangerous.
11. Decommissioning procedure
`Isolate electrical supplies and make safe
`Isolate the water supply
`Drain the product
`Remove product
`Cap pipework
Environmental information
The Waste Electrical and Electronic Equipment
(Producer Responsibility) Regulation 2004
This product is outside of the scope of the European
Waste Electrical & Electronic Equipment Directive as
interpreted within the UK.
In the UK this product can therefore be disposed of
through commercial non-WEEE waste facilities.
Heatrae Sadia does not accept any liability under the
WEEE directive.
This product is manufactured from many recyclable
materials. At the end of its useful life it should be
disposed of at a Local Authority Recycling Centre to
realise the full environmental benets.
Insulation of the product is by means of an approved
CFC/HCFC free polyurethane foam with an ozone
depletion factor of zero and a Global Warming
Potential (GWP) of 3.1.
The product does not contain any substances
harmful to health; it does not contain any asbestos.
Description Code No
Element plate assembly -
10 litre 3kW
95 606 921
Element plate assembly -
15 litre 3kW
95 606 922
Element plate assembly -
10 litre 4.5kW
95 606 923
Element plate assembly -
15 litre 4.5kW
95 606 924
Combined thermostat/thermal
cut-out 3kW
95 612 633
Combined thermostat/thermal
cut-out 4.5kW
95 612 634
Indicator light 3kW 95 607 992
Indicator light 4.5kW 95 607 993
Element plate gasket 95 611 708
Pressure (expansion) Relief Valve 95 607 986
Temperature/Pressure Relief Valve 95 605 045
Check Valve 95 607 987
Expansion Vessel 95 607 988
Pressure Reducing Valve 95 607 989
Top cover moulding 95 614 181
Terminal cover c/w thermostat knob 95 614 182

15
Warranty
The product warranty is for a period of ve years
from the date of purchase with the exception of the
immersion heater and thermal controls which are
covered for a period of two years provided:
1. The product has been installed in accordance
with these instructions and all necessary inlet
controls and safety valves have been tted
correctly.
2. Any valves or controls are of Heatrae Sadia
recommended type.
3. The product has not been tampered with and
has been regularly maintained as detailed in
these instructions.
4. The product has been used only for heating
potable water.
5. Within 60 days of installation, the user completes
and returns the certicate supplied along with
proof of purchase to register the product.
The product is not covered against damage by frost
and the immersion heater is not covered against
excessive scale build up.
This warranty does not affect the statutory rights of
the consumer.
Accessories
The product can be used to supply several hot water
outlets via conventional taps. It is not recommended
for supplying a shower. Individual site demands
should be considered when choosing capacity and
the number of outlets to be served.
A Thermostatic Blending Valve can be used in
conjunction with this product. Accessory Pack U3
(code no. 95 970 354) is recommended. Follow the
installation instructions supplied with the valve for
connection to the system.

Please follow us online:
Electric Water Heating Co.
2 Horsecroft Place
Pinnacles
Harlow
Essex CM19 5BT
Tel: [phone]
E-Mail: [email protected].uk
SPD
Special Product Division
Units 9 & 10
Hexagon Business Centre
Springeld Road
Hayes
Middlesex UB4 0TY
Tel: [phone]
Parts Center
Tel: [phone]
www.partscenter.co.uk
Newey & Eyre
Unit 3-5 Wassage Way
Hampton Lovett Ind. Estate
Droitwich, Worcestershire
WR9 0NX
Tel: [phone]
Fax: [phone]
UK Spares Ltd
Unit 1155
Aztec West
Almondsbury
Bristol BS32 4TF
Tel: [phone]
Alternatively contact your
local supplying merchant
or wholesale branch or use
our online stockist nder at
www.interpartspares.co.uk
PRODUCT RANGE
Full specication details on all our products are available to download from our website.
To support our corporate responsibility and sustainability charters and reduce our
printed material we encourage you to download product brochures from our website.
In designing these les we have taken into account the need to access data on screen.
If you would like to receive a printed copy of our full product catalogue please call
our literature hotline on 01603 420127.
Heatrae Sadia may introduce modications to their products from time
to time. Consequently, the details given in this brochure are subject to alteration
without notice.
OUR NATIONWIDE NETWORK OF CUSTOMER SUPPORT ENGINEERS
Heatrae Sadia has its very own dedicated nationwide network of highly trained
customer support engineers so you can have peace of mind that we’re always
here to help.
MADE IN
THE UK
5
5 YEAR
INNER
CONTAINER
WARRANTY
SPECIFICATION ADVICE HOTLINE
t| 01603 420220 e| speci[email protected]
AFTER SALES SERVICE
t| 0344 871 1535 e| customer.suppor[email protected]
w | heatraesadia.com
16
PN 36 00 5718 Issue 6
©Heatrae Sadia 2015