Heatstore HSTIRFN User manual

1
Issue 02
1. Introduction
Please read this guide carefully and retain for future use and maintenance.
Installation and User Guide
HSTIRFN Single Zone
Wireless Controller
The control icons perform the following basic functions:
Decrease / Increase value: by default this adjusts the set temperature. When the set temperature is adjusted
above the measured room temperature, the heater active symbol is shown and any paired heaters are
switched on.
Mode: cycle through operating modes Boost, Manual, Setback and Program (see sections 6-9).
By default Setback mode is disabled (see section 8).
Fan: cycle through fan speed settings (for fan heaters only). No fan symbol shown means low speed, one fan
symbol is medium speed, two fan symbols is high speed.
Pressing fan when heating is inactive will activate fan only mode (for compatible fan heaters).
In fan only mode, FAN is shown on the display. Exit fan only mode by cycling through the fan speed
settings until FAN is not shown.
Programme: used for advancing programme, setting the time and accessing programming menu.
Important display icons:
Heat icon: this is displayed when the heating is active. WX heaters will operate at reduced heat output when
close to the set temperature, and half the icon is shown:
Lock symbol: this is displayed when the HSTIRFN controls are locked. Hold and together for 5 seconds to
unlock or lock the controls.
ALARM! Flashes to indicate an error in the programme setup, e.g. the time for programme 2 is set earlier than the
time for programme 1.
2. Getting to know your HSTIRFN wireless controller
The HSTIRFN Wireless Controller can control any ‘WX’ or ‘RF’ heater, including multiple products at the same time.
The HSTIRFN must be paired to each heater, otherwise the heaters will not work (see section 3).
For options for powering the HSTIRFN see section 16.
connection symbol (not utilised)

To quickly switch off the heaters and disable the operation of
the HSTIRFN until it is re-enabled,touch and hold for 2
seconds.
When disabled the day and time will be displayed.
Touch to re-enable the HSTIRFN.
In manual mode, the set temperature and fan speed can be
set and will remain unchanged.
Boost mode is used to temporarily boost the set temperature
and/or the fan speed.
2
Issue 02
This must be done, otherwise the heaters will not work.
Power up the HSTIRFN (see section ‘Power options’ for details).
There are 2 different sequences used for pairing. The sequence
used will depend on the heater.
To find out which sequence to use, check the heater rating
label and identify the model number.
If the heater is ‘WX’ and the last two digits are lower than 10
use sequence 1.
If the heater is ‘WX’ and the last two digits are 10 or higher use
sequence 2.
If the heater is ‘RF’ use sequence 2.
If the rating label is not visible, follow the steps below:
Ensure the heater is switched OFF.
Switch the heater ON and observe the LED status light.
If the LED flashes red then goes green use sequence 1.
If the LED is solid green use sequence 2.
Sequence 1
Set heater into pairing mode as follows:
1. Locate the heater LED status light.
2. Turn power to the heater ON. Count 4 seconds, or
count 5 red flashes of the status light on the heater.
Turn power OFF.
3. Turn power back ON. The heater status light should
be flashing green.
(If the light is not flashing green, the 4 second timing
was incorrect. Repeat step 1.)
4. The heater is now ready for pairing with HSTIRFN.
The next 3 steps must be done within 30 seconds. After 30
seconds the heater will return to normal operating mode.
Set the HSTIRFN into pairing mode as follows:
1. Touch and hold and icons together for 5
seconds.
2. The display will show HSTIRFN identification code.
3. Touch the button while the light on the heater is
flashing green.
If the pairing was successful, the light will stop flashing and the
heater is paired with HSTIRFN.
Pairing Sequence
Set heater into pairing mode as follows:
1. Locate the heater status light.
2. Turn power to the heater ON. The light should be
solid green.
The next step must be done within 20 seconds. After 20
seconds, the heater will return to normal operating mode.
Set the HSTIRFN into pairing mode as follows:
1. Touch and hold and icons together for 5
seconds.
2. The display will show HSTIRFN identification code.
3. Touch the button and the HSTIRFN will beep &
flash 3 times.
3. Pairing HSTIRFN with heaters 3. Pairing HSTIRFN with heaters (cont’d)
If the pairing was successful, the light will show red and the
heat output will switch on and stay on if the HSTIRFN is
signal-ling the heat output to be on.
If the HSTIRFN is signalling the heat output to be off, the
heat output will only switch on for a short period of time to
show pairing was successful.
4. Time and day setting
1. To set the time and day the HSTIRFN has to be in
MANUAL, BOOST or SETBACK mode (not available in
basic mode).
2. Touch and hold for 5 seconds.
3. The display changes to show the currently set day and
the time, with the minutes flashing.
4. Use or to set the minutes.
5. Touch to switch to setting the hours.
6. Use or to set hours.
7. Touch to switch to setting the day.
8. Use or to select day.
9. Touch to save and exit time and day setting.
7. BOOST - Boost mode
After entering Boost mode, use and as normal to set
the temperature and to set the fan speed.
The timer defaults to 15 minutes. Press to adjust the boost
time in 15 minute increments up to a maximum of 4 hours.
When the timer finishes, the HSTIRFN goes back to the
previous mode.
Setback mode can be used for frost protection, situations
where a minimum room temperature must be maintained, or
to disable the heating completely.
To disable heating lower the temperature to below 4ºc and
the screen will show ‘- - -’ The heating is now disabled.
Setback mode is disabled by default. To enable, a setting in
the setup menu needs to be changed (see section 21).
Setting 06 should be changed to 1.
8. SETB - Setback mode
5. Disable
6. MAN - Manual mode
In manual mode, the set temperature and fan speed can be
set and will remain unchanged.

Issue 02
icon to set the new
Touch to ADVANCE to next programme number, touch again to go back.
Programme time format defaults to weekday/weekend setting. This lets you set a programme of up to 6 programming
steps which will operate on Monday, Tuesday, Wednesday, Thursday and Friday, and another programme of up to 6
programming steps which will operate on Saturday and Sunday. The programme time format can be toggled between
5d2, 7d or 24h.
This can be adjusted in the settings (Section 21 - Setting 13).
10. Set programme
06:00
10
20
08:00
19ºC
4ºC
ºC
12:00
22ºC
14:00 16:00
16ºC
22ºC
10ºC
22:00
PROGRAM 1 PROGRAM 2 PROGRAM 3
An example of one day programme on HSTIRFN
PROGRAM 6
-SET HOURS FOR PROGRAM
- SELECT DAY TO SET
- SET MINUTES FOR PROGRAM
- SELECT PROGRAM TO SET
- SET TEMPERATURE FOR PROGRAM
Logic diagram for setting programme on HSTIRFN
1. To set up the heating programme the HSTIRFN has
to be in PROG mode.
2. Touch and hold for 5 seconds.
Programme mode is now displayed, with the
displayed day/days flashing.
3. Touch or to select the day (in 7 day mode) or
group of days (in other modes) you want to set.
4. Touch to confirm day.
The program number is now shown flashing.
5. Touch or to select programme step number.
6. Touch to enable/disable selected program.
7. Touch to confirm programme number.
The minute display is now shown flashing.
8. Touch or to set minutes in 15 minute increments.
9. Touch to confirm minutes.
The hour display is now shown flashing.
10. Touch or to set hour.
11. Touch to confirm hours.
The programme temperature is now shown flashing.
12. Touch or to set temperature.
13. Touch to confirm temperature.
This program is now set
The day/days is shown flashing ready for the next
programme.
14. Wait 20 seconds to automatically exit programming
11. Set programme active / inactive
In programming mode, select the programme you want to
make active or inactive. Touch to toggle between settings.
E.g. Programme 3 inactive Programme 3 active
or
9. PROG - Automatic time mode
In this mode, the HSTIRFN will follow the week’s time / temperature programme.
You can override the temperature in PROG mode by simply activating the HSTIRFN and using the
temperature. The new set temperature will be then maintained until the next programme step.
3
PROGRAM 5
PROGRAM 4

4
12. Copy day function
The HSTIRFN allows you to copy a day’s heating programme
to save time re-entering the same time and temperature
settings for each day.
This function is only available when in 7 day mode.
1. To use a copy day function, enter the programming
mode.
2. Touch to activate the COPY DAY function.
3. Touch to select the day you want to copy the
temperature settings from.
4. Touch or to select the day you want to copy the
temperature settings to.
5. Touch to confirm the selection.
The ‘to’ word will flash to indicate that the day programme
has been copied to the day selected.
6. Touch to go back to the Programme mode.
Please note that the controller screen will take up to
one minute to display after powering up for the FIRST
time.
The HSTIRFN controller can be powered either by a 5V
power adapter with a micro USB connector, supplied
power adapter via USB port or 4 AAA batteries. There are 2
available USB ports for power. One port is located on the
bottom and one at the back of the controller.
The display will show the battery status only when the
HSTIRFN is powered by batteries alone.
16. Power options
15 . Choosing a position in a room
The HSTIRFN should be fixed to the wall or used with the
table top stand. Avoid areas with draught or direct sun.
Do not position HSTIRFN above or close to the heaters or
other heat sources. Damp areas or areas where HSTIRFN
can be mechanically damaged should also be avoided.
Remove the HSTIRFN’s battery cover and insert 4 new high
quality alkaline AAA batteries.
Warning: responsible for damage due to
corrosion. Battery leakage will cause permanent damage.
To help avoid battery leak:
Note: The clock has to be set after replacing the batteries, or
if the USB power cable has been disconnected from the
HSTIRFN or power to the power adapter switched off. If the
HSTIRFN is powered by the power adapter,
2 AAA batteries can be used to supply power in the event of
a power cut in order to keep the clock running. The batteries
should be replaced annually.
17 . Batteries
14. Status light on the heater
Light colour Heater status
Heater is in stand-by mode/ not receiving
signal from controller. Heater is ready for
pairing with controller.
Heater paired successfully - Solid Purple
light for 5 seconds (WX models only).
Reduced heat output (WX models only).
Full power heat output
13. Fan speed settings (fan heaters only)
Each operating mode MANUAL, BOOST, SETBACK and
PROGRAM remembers its own fan speed setting. This speed
setting is used whenever the heating is active in that mode.
The default fan speed is medium speed for MANUAL,
SETBACK and PROGRAM modes, and high speed for BOOST.
To adjust the fan speed setting, touch when heating is
active to cycle through fan speeds. For the purposes of
setting the fan speed, the heating can be made active by
temporarily increasing the set temperature.
Heater is in fan only mode (WX models only).
If the LED is flashing white, there is a fault.
The unit will continue to function in
restricted mode. However, in specific
circumstances, the unit will stop running
(WX models only).
•Replace the batteries annually, even if there is not a
low battery warning. Remove failing or flat batteries
immediately
•Always fit new high quality alkaline batteries from the
same pack. Never mix new and old batteries, or
batteries of different brands or types
•Never attempt to revive alkaline batteries by heating,
crushing or recharging.
Issue 02

The HSTIRFN can also operate in Manual Control Mode.
In this mode, heat and fan settings can be manually set, and
the room temperature is not used to switch the heaters.
5
18. P ower adapter for fixed installation
The HSTIRFN controller is supplied with a power adapter
that will fit a 35mm or a 25mm metal or dry lining back
box. The power adapter should only be connected to a
wiring protected by a 6A fuse or 6A circuit breaker.
Connect line and neutral conductors to the terminal
block. Please note that the adaptor supplied with the
controller must be installed exactly as the figures show,
otherwise the USB connector will not fit correctly. The
centre of the back box must be kept clear to allow room
for the USB connector.
When fitting the wall bracket, ensure that the adaptor is
installed properly and feed the cable through the centre of
the bracket. Screw the bracket to a back box taking care
not to damage the power adaptor or leads with long screws.
Connect the USB cable into the power port at back of the
controller as shown on the photo. Check that the HSTIRFN is
working. Attach top of the HSTIRFN to the wall bracket and
slowly tilt it to place observing that the USB connector is
moving in to the opening freely. Once the controller is in
place secure the two screws on the bottom of the controller.
To ensure you don’t waste energy on heating the outside
world, the heater is equipped with an optional open / closed
window detection. The heater recognises sudden drops in
temperature when a window or a door is opened and turns
the heating off to save energy. When the window is closed,
the heater will automatically detect a temperature rise, and
switch itself back on. Once enabled in the setup menu, the
open window detection is fully automatic and does not
require any human intervention to be activated.
Setting-up Open Window Detection
The system has been factory set to default time and
temperature values. When the heating is on, open window
detection sensor will automatically switch the heater off
when it detects a fall in temperature of 2°C in less than 10
minutes. If a temperature rise of 2°C in less than 30 seconds is
detected, the heater will switch itself back on.
These values can be adjusted in the setup menu, detailed in
section 21 - Settings 07-11.
locking screws
USB power ports
temperature sensor
wall fixing
wall fixing
20. Manual Control Mode
The fan speed F0, F1, F2 or F3 is displayed on the left side of
the display. Touch to cycle through the fan settings.
The heat setting H0, H1, H2 or H3 is displayed on the right side
of the display. Touch or to adjust the heat setting.
In Manual Control Mode, many of the functions of the
HSTIRFN are very similar to automatic mode, except that the
fan and heat settings are adjusted instead of the set
temperature:
•Boost mode can be used to temporarily override the
heat and fan settings.
•Programmes can be set up with up with the same
flexibility as in automatic mode.
•Manual mode can be used to run the heaters
continuously in one heat and fan setting.
Manual Control Mode is accessed by changing a setting in
the setup menu (see section 21).
Setting 06 should be changed to 2.
19 . Open Window Detection
When the unit is powered by the power adapter, the
temperature reading should be calibrated 1.5°C / 3°F lower.
To do this a setting in the setup menu needs to be changed
(see section 21).
Setting 01 should be changed to –1.5°C.
Issue 02

6
Issue 02
The HSTIRFN has a one year exchange warranty against faulty material or workmanship. This applies only if the
appliance has been used for purposes in accordance with the instructions provided and has not been misused,
neglected, damaged, modified or repaired by any person not authorised by us. This guarantee is offered to you
as an extra benefit and does not affect your legal rights.
Reasonable care has been taken to ensure that this guide is accurate at the time of printing. In the interest of
progress, the Company reserve the right to vary specifications from time to time without notice.
Should you need any advice on the use of yournew product please contact Heatstore:
Customer Helpline
2. Use to go to the next setting.
3. Use and to change the value.
4. Touch to save and exit setup.
01 - temperature calibration
The temperature reading has been factory calibrated
but if for any reason it needs adjusting (power
adapter compensation, better accuracy required, to
suit different position in the room etc.) the reading
can be recalibrated in 0.5 degrees steps.
02 - change between degrees Celsius or Fahrenheit.
03 - set minimum temperature
(- - - = heating OFF, 4°C = frost protection)
04 - set maximum temperature
05 - information about the software version
21. Setup menu (cont’d)
06 - 0 = Simplified automatic mode (factory default)
1 = Automatic mode
2 = Manual control mode
07 - open window detection 0 = off, 1 = on
08 - 600 - open window detection time 600 seconds
09 - 2°C - temperature drop of 2°C in the detection time
10 - 30 - closed window detection time of 30 seconds
11 - 2°C - temperature rise of 2°C in the detection time
12 - Reset: Touch and wait 10 seconds for full reset to
factory settings
13 - Programme time setting
5d2 = weekday and weekend settings
24h = every day uses same programme
7d = 7 unique day settings
14 - Not currently Utilised
®
Telephone: [phone]
Unit 12, Access 18, Bristol BS11 8HT
www.heatstore.co.uk
1. To access the setup menu, touch and hold and
together for 5 seconds.
In the menu, settings are numbered 1 to 14. This setting
number is displayed on the left and the value of the
setting is displayed on the right.
21.Setup menu