HELLER WAL40R User manual

READ AND SAVE THESE INSTRUCTIONS
Instruction Manual
40cm Wall Fan
With Remote Control
Model: WAL40R

Please read and follow the instructions in this user manual even if you feel you are familiar with the
product, and find a place to keep it handy for future reference.
For your convenience record the complete model number (located on the product identification plate)
and the date you received the product, together with your purchase receipt and attach to the warranty
and service information. Retain in the event that warranty service is required.
NOTE: The rating of this product (as marked on the product identification plate) is based on specific
loading tests. Normal use or the use of other recommended attachments may draw significantly less
power.
IMPORTANT SAFEGUARDS
When using any electrically powered product, basic safety precautions should always be followed,
including the following:
PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT
WARNING!: - to reduce the risk of fire, electrical shock or injury to persons or property:
•Always operate the product from a power source of the same voltage, frequency and rating as
indicated on the product identification plate.
•To reduce the risk of electric shock, do not use this fan with any solid state speed control device.
•Remove the unit from its packaging and check to make sure it is in good condition before using.
•Do not let children play with parts of the packing (such as plastic bags).
•Close supervision is necessary when the product is used by or near children or infirm persons. Do
not allow children to use it as a toy.
•Do not operate any product with a damaged cord or plug, or after the product malfunctions, or is
dropped or appears damaged in any way. Return the complete product to the place of purchase
for inspection, repair or replacement.
•Before unplugging the power cord, be sure to turn the power off. When touching the unit, be
sure your hands are dry to prevent electrical shock.
•Fully remove the power cord from the power cord tidy before use. Always uncoil the power cord
before applying power.
•Ensure the fan is mounted on a stable, even wall, which is strong enough to hold it.
•The wall fan must be installed so the blades are at least 2.1m from the floor.
•Never install the unit where it is exposed to direct sunlight, excessive moisture/rain, dust and lack
of ventilation near any heat sources.
•Avoid making contact with moving parts. Never insert fingers, pencils or any other objects
through the guards whenever the power plug is connected, especially while the unit is working.
•To reduce the risk of electric shock, do not immerse or expose the product or flexible cord to
rain, moisture or any liquid other than those necessary for correct operation of the product.
•This product should not be used in the immediate vicinity of water, such as bathtub, washbowls,
bathroom swimming pool etc. Where the likelihood of immersion or splashing could occur.
•Switch off and unplug from outlet when not in use, before assembling or disassembling parts and
before cleaning. Remove by grasping the plug - do not pull on the cord.
•Be sure that no other high current appliances are plugged into the same circuit with your fan as
an overload can occur.
•Do not use this unit with a programmer timer or any other device that switches the unit ‘On’
automatically, since a fire risk exist the unit is covered or positioned incorrectly.

•Avoid the use of an extension cord as the extension cord may overheat and cause a risk of fire.
•Do not plug this unit into an extension lead, double adaptor or power board.
•Do not use the appliance for other than its intended use.
•Do not use outdoors. FOR INDOOR USE ONLY.
•This unit is not intended for use in bathrooms, laundry areas or similar moist indoor locations.
Never locate the unit where it may fall into a bathtub, sink or any other water container.
•Do not run the power cord under carpeting or cover the power cord with throw rugs, runners or
the like. Arrange the power cord away from traffic areas and where it will not be a hazard to
persons.
•Do not place the power cord over any part of the unit.
•Do not leave the appliance unattended when switched on.
•Do not cover the grill, or operate in close proximity to curtains etc.
•Do not block air circulation.
•Do not move the machine when it is switched ‘On’ and in use.
•Place the machine on a level surface.
•To disconnect the unit, set the main switch to ‘OFF’ then remove the plug from the outlet.
•This unit has hot electrical parts inside. DO NOT use it in areas where gasoline, paint or
flammable liquids are used or stored.
•Unplug the appliance during filling and cleaning.
•This product must always be used and stored in the upright position.
•Batteries must be inserted into the remote control which must be pointed direct at the unit,
using the front portion to activate.
•The use of attachments or accessories not recommended or sold by the product distributor may
cause personal or property hazards or injuries.
•This product is intended for normal domestic/household use only.
•Use this fan as described in this manual. Any other uses, not recommended by the manufacturer,
may cause fire, electric shock, or injury to persons and may void the warranty.
•This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the appliance by a person responsible for their
safety.
•The installation of a residual current device (safety switch) is recommended to provide
additional safety protection when using electrical appliances. It is advisable that a safety switch
with a rated residual operating current not exceeding 30mA be installed in the electrical circuit
supplying the appliance. See your electrician for professional advice.
•WARNING: If the supply power cord is damaged, the power cord must be replaced by the
manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
•This product has not been designed for any uses other than those specified in this booklet.
SAVE THESE INSTRUCTIONS

PARTS & FEATURES
1)
Screws
8)
Front Guard
2)
Hanging Bracket
9)
Safety screw
3)
Motor control Assembly
10)
Swivel brackets
4)
Rear guard
11)
Bracket fix
5)
Rear guard securing ring
12)
Plastic protector
6)
Fan blade
13)
Control panel
7)
Fan blade securing cap nut
14)
Remote control
BEFORE FIRST USE
Before use, remove all packaging and inspect the appliance for any damage. If there appears to be any
damage, please take the unit back to place of purchase for a replacement.
ASSEMBLY INSTRUCTIONS
Please refer to the “Parts & Features” Diagram.
1. Mount the hanging bracket (2) on the wall with the screws (1) provided (Fig.1).
2. Hang the motor and control assembly (3) with the bracket (11) onto the hanging bracket (Fig.2).
3. Remove the plastic protector (12).
4. Loosen the rear guard securing ring (5) from the motor housing assembly.

CAUTION: To avoid of electric shock, you must always switch off and unplug the fan before cleaning.
5. Position the rear guard (4) firmly to the motor housing assembly and fasten by turning the rear
guard securing ring (5) clockwise tightly.
6. Push the fan blade (6) along the motor shaft.
7. Fasten securely, using the fan blade securing unit nut (7) with the spinner by turning anti-
clockwise.
8. Mount the front guard (8) to the rear guard, by positioning the hook on the front guard over the
top of the rear guard. Secure the two grilles with clips and screw attached to the grill.
OPERATING INSTRUCTIONS
Remove the cable tie and unravel the cord set before operation. Connect the plug into an electrical
socket and switch on at the wall.
SPEED/ON
Press the “SPEED/ON” button. At first start-up the fan will operate at low speed. Press the same button
to choose between Low, Medium and High speed.
SWING
Press “SWING” button to switch on the oscillation mode. The fan oscillates from left to right, to stop
press the button again.
MODE
There are 3 mode functions; Normal, Natural and Sleep.
TIMER
Press this button repeatedly to change the timer setting. When you press the TIMER button the function
is activated. You can set the timer from 0.5 –7.5 hours, each time you press this button it will increase
by 0.5 hours. No obstacles should stand between the remote control and fan otherwise it will not
function.
REMOTE CONTROL
The sensor of the remote control must be pointed at the fan receiver to operate properly. The distance
between the remote and receiver should be no more than 6 metres and 30 degrees radius, left to right
of the fan.
CARE & CLEANING
•Your appliance must be switched OFF via the main power supply and unplugged before
proceeding with any cleaning.
•Clean the housing with a damp cloth, a vacuum cleaner or a dusting brush.
•To clean the blade and grille assembly, first remove the safety grille, unscrew the locknut and
remove the blade from the Wall Fan. Wipe them clean with a slightly damp sponge.
NOTE: If the power cord set of this appliance becomes damaged, discontinue use. Repairs should be
undertaken only by a qualified technician.
NOTE: Before inserting the plug into a power outlet, make sure that the correct voltage being used
corresponds to what is indicated on the rating label, and that the socket has an earth facility.

•Never use flammable or abrasive cleaning agents such as benzene or spirits to clean the
appliance.
•Never immerse the appliance in water.
•Never spray the Wall Fan with liquids or submerge it in water or any other liquid.
•Store the fan in a clean dry place when not in use.
SPECIFICATIONS
Model
Description
Voltage
Frequency
Wattage
WAL40R
40cm Wall Fan with
Remote Control
220-240V~
50/60Hz
60W
CUSTOMER SERVICE
Australian Customer Service
GAF Control (Sales) Pty Ltd
P.O Box 19
Altona North Victoria 3025
Phone: [phone]
Hours: 9am-5pm (EST) Mon-Fri
www.gafcontrol.com.au
*This product may vary slightly to the product illustrated due to ongoing product development.