Henderson Magic 600 User manual

Magic 600
DE Garagentorantrieb PL Napęd do bram garażowych
GB Garage door operator SI Pogon za garažna vrata
FR Motorisation de porte de garage CZ Pohon garážových vrat
SE Portautomatik SK Pohon garážových brán
DK Garageportmotor GR Μηχανισμός κίνησης γκαραζόποτρας
NO Garasjeportåpner ES Accionamiento de la puerta de garaje
FI Ovikoneisto PT Automatismo para portões de garagem
NL Garagedeuraandrijving BG Задвижване на гаражна врата
IT Motorizzazione per garage HR Pogon garažnih vrata
HU Garázskapu-hajtóműRO Acţionare poartăde garaj
RU Привод гаражных ворот AE
ΕΎΟ΍ήΠϟ΍ ΕΎΑ΍ϮΑ ϚϳήΤΗ ϡΎψϧ
N000924 12/2010

8 / 208 N000924 12/2010 Magic 600
GB English
Translation of the German original operating manual
Table of contents
1 Introduction 8
2 Product description 8
3 Symbols 8
4 Intended usage, Guarantee 8
5 Informal Safety Measures 8
6 Safety instructions 8
7 Installation precautions 9
8 Safety devices of the door operator 9
9 Safety inspection 9
Checking load switch-off
Emergency release
Additional safety devices
10 Controls and indicators 9
11 Connections 9
12 Installation preparations 9
13 Installation 10
14 Commissioning 10
15 Teaching in the door operator 10
Teaching in with a remote transmitter
Teaching in without a remote transmitter
16 Teaching in/deleting a remote transmitter 10
17 Operation 10
18 Programming 10
19 Reset 12
20 Attaching additional safety devices 12
Photo cell
EMERGENCY stop
21 Additional connections 12
Additional lighting
External pulse input
Additional antenna
22 Troubleshooting 12
Causes of errors/Remedies
Changing the battery of the remote transmitter
23 Maintenance intervals 13
24 Declaration of conformity 13
25 Technical data 13
26 Replacement parts 13
27 Accessories (optional) 13
28 Removal, Disposal 13
Read operating instructions carefully before installing and
commissioning. Pay attention to the illustrations and all notes.
The remote transmitter supplied is taught in to the door
operator.
Packaging: Only reusable materials are used. Dispose of
packaging in an environmentally-friendly way and according
to local legal guidelines.
Scope of delivery see page 162
The following symbols are used in this manual:
CAUTION Warns of potential injury and material
damage. Non-observance of instructions marked with
these symbols can result in serious injuries and material
damage.
NOTE: Important technical instructions that must be
observed.
This door operator is suitable for use in domestic garages.
Any other use is deemed incorrect.
This product must not be used in explosion-protected
atmospheres.
The manufacturer must provide written and express approval
for:
• Modifications or attachments
• Use of parts other than factory authorised replacement
parts
• Repairs performed by persons or businesses that have not
been authorised by the manufacturer.
If approval is not obtained for any of the above, this may
invalidate the product’s guarantee.
We will not be liable for damage
• Due to non-compliance with operating instructions
• Due to technical errors in connecting the door operator and
structural deformations that may occur during operation
• As a result of inappropriate door maintenance.
door maintenance.
Keep the operating instructions handy for future use.
The inspection and testing log book provided must be filled
out by the person carrying out the installation and kept by the
operator along with all other documentation (door, door
operator).
General safety instructions
The door operator may only be used if the entire range
of motion is clearly visible. Be mindful of others within the
action range of this product during operation.
Always disconnect the electrical power before working on the
door operator.
Actions prohibited during use of a door operator:
• Passing or driving underneath a moving door
• Lifting of objects and/or persons with the door
• Children must not be left to operate the product
unsupervised; it is not a toy.
The door must only be operated when
• all users are familiar with its functions and operation.
• the door meets the requirements of European standards
EN 12604, EN 12605 and DIN EN 13241-1.
• the door operator is installed in compliance with the
relevant standards (EN 12453, EN 12445 and EN 12635).
• any optional safety devices such as a photo cell,
optosensor or safety rail are fully functional.
• garages without a second entrance have an emergency
lock release from the outside. It may be ordered separately
if necessary.
• an inset door in the garage door is closed and is equipped
with a safety device that prevents activation when the door
is open.
• an additional safety device (safety rail, etc.) has been
installed prior to activation of the automatic closure
function.
• If a person with restricted physical, sensory or mental
capacity, or a person with little experience and/or
knowledge of the door operator is to use the device, they
1 Introduction
2 Product description
3 Symbols
4 Intended usage, Guarantee
5 Informal Safety Measures
6 Safety instructions

Magic 600 N000924 12/2010 9 / 208
must be supervised by a person who assumes
responsibility for their safety.
Installation must be performed by qualified service
technician.
Work on the electrical installation must only be carried out by
authorised specialist personnel.
The load capacity and suitability of the supporting
construction of the building in which the door operator is to be
installed must be inspected and approved by an expert.
The door operator must be fully and securely attached at all
fastening points. All fastening materials must be selected
according to the nature of the supporting construction and
they must be able to withstand traction force of 900 N.
In the event of non-conformance with these
requirements, there is a risk of injury and material
damage caused by a falling operator or an uncontrolled
movement of the door.
When drilling the fastening holes, do not damage the building
structure or any electrical, water or other lines.
After lifting up the door operator to the ceiling, fasten it fully
with appropriate tools to prevent it from falling down. See
illustration on page 159.
Please observe appropriate industrial safety regulations and
keep children away during installation.
The door operator has the following safety devices. Do
not remove them or alter their functionality.
• Automatic load switch-off during functions "OPEN" and
"CLOSE"
• Connection for photo cell / safety rail / optosensor
• EMERGENCY stop connection: Connection of a switch
(optional) to an inset door mounted in the garage door, for
example
• Emergency release (see page 161 (J))
Checking load switch-off
The automatic load switch-off is a clamping and safety
mechanism that is designed to prevent accidents due to a
moving door.
Stop the door from outside with both hands at waist height.
When closing:
The door must stop automatically and reverse a little if it
comes into contact with an obstruction.
When opening:
The door must stop automatically when it meets with
resistance (if menu A7 = 1, it moves back a short distance).
After load switch-off, the door operator lights flash until the
next pulse or wireless command is received.
Emergency release
Check as per the information provided on page 161 (J).
Additional safety devices
Check for proper functioning as per the manufacturer’s
instructions.
Messages of the indicator lamp (8)
Please note: Check that the door is working properly
and running smoothly, and adjust if necessary. The
spring tension of the door must be set in such a way that it is
stable and can be opened and closed by hand smoothly and
without jolting.
• Standard and appropriate shock-proof socket approx. 10 -
50 cm away from the fastening position for the head of the
operator.
(For information on fuses, see the technical data.)
• Only install the door operator in dry garages.
Make sure the installation set for the connection is ready on
7 Installation precautions
8 Safety devices of the door operator
9 Safety inspection
10 Controls and indicators
5 Pushbutton Close door / Minus
6 Pushbutton Menu / Confirm (Teach-in run)
7 Pushbutton Open door / Plus
8 Indicator lamp
Status messages
A door in end position OPEN
Bdoor between the two end positions
Cdoor in end position CLOSED
Status messages
During door movement in OPEN direction
C=> B=> A...
During door movement in CLOSE direction
A=> B=> C...
L4 Set end position OPEN
L3 Reference run CLOSE and set end position CLOSED
L2 Teach-in run OPEN (load values)
L1 Teach-in run CLOSE (load values)
Err Error and error number (flashing)
11 Connections
1 EMERGENCY stop (green)
2 Photo cell (yellow)
3Pulse
12 Installation preparations
567
8
ABC
132

10 / 208 N000924 12/2010 Magic 600
the door type that is being attached and/or install it according
to the relevant manual.
See instructions for installation on page ff 155.
The head of the operator can be turned by 90° to the running
rail respectively as required (see page 155 (A)).
Installation step D, page 156:
1. Tighten the toothed belt’s clamping nut until the toothed
belt no longer rests on the guide rail (equivalent to
dimension X).
2. Use the clamping nut (dimension B) to increase the
toothed belt tension to correspond to the length of the door
operator.
Once installation is complete
• Slowly open the door by hand until you hear the slide snap
in.
• Make connection to mains, display flashes alternately with
L and 4. The door operator lamp flashes in intervals of 4.
• Teach in the door operator (see Chapter 15).
• Teach in the remote transmitter (see Chapter 16).
• Carry out a safety inspection (see Chapter 9).
ATTENTION: No protection is provided by the load
switch-off whilst the door operator is being taught
in.
Note: Teaching in is only possible during initial installation or
after resetting the door operator. Do not press any keys
during the teach-in procedure.
Preparation: Connect the door to the door operator.
Teaching in with a remote transmitter
At the time of delivery and after resetting the door
operator, the remote transmitter supports the following
functions:
• A Safety control operation and fine adjustment "OPEN"
• B Safety control operation and fine adjustment "CLOSE"
• C and D Confirmation (storage)
Once the door operator has been taught
in, key A is used for remote control and
the other keys can be used to control
other similar door operators or other
radio receivers.
Teaching in
• Press and hold down key A; the door
moves in the open direction.
• When you reach the desired end position "OPEN", release
key A. (You can make corrections with key B.)
• Press key C once briefly, teach-in procedure: The door
operator automatically stores "End position OPEN/CLOSE"
and the loads of the "Travel path OPEN/CLOSE". The door
operator lights flash in synchronism.
Teach-in is complete when the door is open and the door
operator lights are on.
Check load switch-off according to Chapter 9,Safety
inspection.
Teaching in without a remote transmitter
On the door operator:
• Press and hold pushbutton and the door moves in the
open direction. Release pushbutton when the desired
opening position is reached. A correction can be made with
the pushbutton .
• Press the Menu pushbutton The door operator
automatically stores "End position OPEN/CLOSE" and the
loads of the "Travel path OPEN/CLOSE" . The door
operator lights flash in synchronism.
Teach-in is complete when the door is open and the door
operator lights are on.
Check load switch-off according to Chapter 9,Safety
inspection.
Programming the remote transmitter:
• During one of the 3 status messages A, B or C (seeChapter
10), press the pushbuttons and simultaneously
(approx. 1 s), F flashes in the display.
• Press the desired key on the remote transmitter, the radio
command is taught in. F appears in the display.
Note: F appears in the display during the transmission pulse.
Deleting (all) remote transmitter(s):
During one of the 3 status messages A, B or C (see Chapter
10), press the pushbuttons and simultaneously for >6
seconds, F flashes in the display. The status message
reappears after 3 seconds.
CAUTION: Mishandling the product can result in
injuries or material damage. Follow the basic safety
rules:
When opening or closing the door, do not block the interior or
exterior swivel ranges. Keep children away.
The door movements can be activated or stopped using the
remote transmitter provided or via switching elements such
as the wall keypad, which can be connected if desired.
Optional external features (such as the EMERGENCY STOP)
can also be connected to the door operator.
The operator must be connected to a door before
it is used. If it is not, incorrect load values will be
taught in to the electronic system. This can cause
malfunctions.
Switch on programming mode
During one of the 3 status messages A, B or C (seeChapter
10) press the Menu pusbutton for longer than 1.5
seconds. The display changes to the menu (D).
Select programming menu
Select the desired menu with the pushbuttons and . The
2-character menu name flashes on and off. The following
appears for menu A0: A 0 A...
Show / change menu value
Displays: Press the Menu pushbutton for less than 1.5
seconds, the menu value (E) is displayed.
Change: Change the value with the pushbuttons and .
Save: Press the Menu pushbutton for less than 1.5
seconds, the programming menu (D) is displayed.
13 Installation
14 Commissioning
15 Teaching in the door operator
16 Teaching in/deleting a remote
transmitter
17 Operation
18 Programming

Magic 600 N000924 12/2010 11 / 208
Exit programming mode
Press the Menu pushbutton for longer than 1.5 seconds,
the display changes to the status message, changes are
saved.
If no key is pressed within 15 seconds during programming, it
automatically exits the programming mode.
ATTENTION: If the values of the programming
menu A0 to A4 are changed, the load switch-off no
longer provides any protection! Teach the door operator in
again before re-commissioning. For this carry out Teaching in
the door operator (Chapter 15) .
1) If the added load (A5, A6) is >3 and/or the automatic
closing (b4) is set to ON (>0), the door may only be
operated with an additional safety device.
Factory setting
Menu
Function, setting range, unit
A0 Length SOFT RUN OPEN in 7cm
0..9
2
A1 Length SOFT RUN CLOSE in 7cm
0..9
4
A2 Soft running speed (CLOSE) mm/s
0= 50...9= 140
5
A3 Backjump, OFF= 0 ON= 1 1
A4 Change in direction, OFF= 0 ON= 1
Setting (with +/-) only possible if EMERGENCY
STOP plug (1, green) is unplugged.
0
A5 Added load 1) OPEN 0..9 3
A6 Added load 1) CLOSE 0..9 3
A7 Door type: Overhead sectional door/one-piece
door = 0
Side sectional door* = 1
Side sectional door with soft start = 2
* Obstruction release also in OPEN direction
0
A8 Warning time (OPEN/CLOSE) 1=2secs...
8=16secs
0
A9 Accessory card
0= ZKMagicS
1= ZKMagic
0
b0 Relay 1 (with ZKMagic accessory card)
0= no function
1= E-lock
2= warning light *
3= photo cell test* (interruption transmitter
voltage)
4= status display*: Door in end position OPEN
5= status display*: Door in end position CLOSED
6= green light*
7= red light*
* if A9= 1
0
DE
DE
ABC
<1,5 Sek
>1,5 Sek
b1 Relay 2 (with ZKMagic accessory card)
0= no function
1= E-lock*
2= warning light *
3= photo cell test* (interruption transmitter
voltage)
4= status display*: Door in end position OPEN
5= status display*: Door in end position CLOSED
6= green light*
7= red light*
* if A9= 1
0
b2 Closing edge protection (accessory module)
0= OFF 1= OSE
0
b3 Empty run detection 0= OFF 1= ON 1
b4 Automatic closure function 1)
0= OFF 1= 10 secs 2= 30 secs
3= 1 min 4= 2 min 5= 3 min
6= 5 min 7= 10 min 9= 15 min
resp. plus warning time
0
b6 Maintenance interval*
0= OFF
1..9 (1,000 door movements)
Example: 5 = 5,000 door movements
The operator lighting flashes after every door
movement when the maintenance interval has run
out. A misadjustment resets the counter of the
maintenance interval.
0
b7 Version number: 8 digits are displayed twice in
succession with leading “-“.
Example: -04200510 indicates:
Version: 04 Date: 20.05.10
b8 Service mode
0= control panel free, menu items adjustable
0= control panel locked, menu items not
adjustable
0= data output (accessory card)
Setting only possible if EMERGENCY STOP plug
(1, green) and photo cell (2, yellow) are
unplugged.
0
b9 Run counter: 8 digits are displayed twice in succession
with leading “-“.
Example: -00008000 indicates:
8,000 runs
C0 Test mode for Magic-Door-Control (option)
Radio signal, maximum 15 seconds:
0= no signal
1= end position OPEN
2= end position CLOSED
3= run open
4= run close
5= standstill underway
7= error
8= obstruction
0

12 / 208 N000924 12/2010 Magic 600
ATTENTION: Ther is no longer any protection by
switching off the load after the reset. Teach the door
operator in again before re-commissioning. For this carry out
Teaching in the door operator (Chapter 15) .
Reset (saved values of the teach-in runs)
During one of the 3 status messages A, B or C (see Chapter
10) press the pushbuttons and Menu simultaneously
for longer than 8 seconds and less than 10 seconds. The
indicator lamp flashes (r), then the status message is
displayed; the reset is carried out.
The remote transmitters are not deleted.
Reset, factory setting
• Pull out the plug (1).
• During one of the 3 status messages A, B or C (see 10)
press the pushbuttons and Menu simultaneously for
longer than 12 seconds. The indicator lamp flashes slowly
at first, then quicker (rES). Then the status display
reappears, the reset is made.
The values shown under Programming (Chapter 18) are
set. The remote transmitters are not reset.
Photo cell
Function: When the safety input is activated (opening the
contact) the operator stops and reverses as far as the OPEN
end position.
If the “automatic closure” function is also activated, following
the third successive obstruction message, the operator will
move to the OPEN end position and shut down.
Connection: Pull out plug with yellow bridge on the external
junction 2 and store it. Plug on safety device.
Safety rail, opto-sensor and warning light are
connected by extension modules.
EMERGENCY stop
Function: If the external safety device is operated when the
door is moving (Contact opened), the door stops immediately.
Once the EMERGENCY stop contact has closed, the door
operator can be moved again with the next pulse.
Connection: Pull out plug with green bridge on the external
junction 5 and store it. Plug on safety device.
Additional lighting
Connection must be performed only by qualified electricians.
In addition to the operator light (40W), optional lighting of a
maximum of 60 W (no tubular fluorescent lamps) can be
connected to terminals 1 and 2.
Note: Some energy saving lamps can interfere with the radio
signal.
External pulse input
An external pulse signal (e.g. wall button) can be connected
to terminals 18 and 19.
Additional antenna
An external antenna can be connected to terminals 21 and 20
(GND). The internal antenna (terminal 21) must be
disconnected.
Figure: Control board See also page 164.
Interference frequencies
The wireless signals of other 433 MHz transmitters can
interfere with the door operator.
Self-test
The system runs a self-test after initialisation, after each
motor operation and after every 2.25 hours in idle mode.
Error free = status message.
Troubleshooting: Reset (Chapter 19) and then perform work
step Teaching in the door operator (Chapter 15)
If the error occurs again, request customer service.
Note: If the same error occurs in two successive self-tests,
the control system will be disabled (commands are rejected).
After approximately one further minute, the system runs
another self-test. If no errors are detected, the control system
is enabled again. If the error persists, a reset will need to be
performed. This will delete all settings and the door operator
will have to be taught in again.
Causes of errors/Remedies
19 Reset
20 Attaching additional safety devices
21 Additional connections
22 Troubleshooting
Error messages*
2 EEprom data
3 Current measurement
4 Hardware Photo cell
5 Switch off thyristors
6 Switch off relay
7 Watchdog test
8 ROM test
9RAMtest
Description Possible cause/Remedy
Door operator light
flashes evenly
The door has hit an obstruction, do
function test
Door operator light
flashes at intervals of
4
Door operator is not taught in,
attention no protection by load
switch-off! Carry out door operator
Teaching in the door operator
(Chapter 15)
Entrapment
protection device not
working.
Incorrect setting of door or
entrapment protection device /
Reset and teach in again
The operator is not
working at all.
None or wrong voltage supply / The
fuse of the motor control is defective
/ Check external terminals 7 and 8.
The operator is
defective. The slides are not snapped-in properly./The toothed belts are not
tensioned correctly./The door
thresholds are frozen.
1
2
21
20
19 18

Magic 600 N000924 12/2010 13 / 208
Changing the fuse
Pull out mains plug.
• Remove the operator hood, see page 164.
• Remove the faulty fuse (S1) from the fuse holder (S2) and
replace it. Make sure that the new fuse has the correct
value!
• Replace the operator hood.
Restore the mains connection.
Changing the battery of the remote
transmitter
Open the housing cover. Remove the battery, fit a new one
and replace the housing cover.
Use only leak-proof batteries. Make sure the polarity
is correct. Dispose of used batteries in an
environmentally-friendly way.
Monthly
• Load switch-off (entrapment protection device)
• Emergency lock release
• Additional safety devices (if fitted)
Every 6 months
• Mounting of door operator on the ceiling and on the wall
See page 167.
Declaration of incorporation see page 168.
1) The transmission range of the remote transmitter may be
reduced considerably by external interference.
2) Dimensions with turned operator head
3) plus stroke length
See pages 162 and 163.
Available from specialised dealer's:
• 4-command multi-use remote transmitter
• Wall keypad
• Key-operated control
• Keypad
• Wireless keypad
• External antenna
• Photo cell
• Extension module for opto-sensor
• Extension module for warning light
• Emergency lock release from outside or inside
• Safety rail 8.2 kohms
• Potential-free receiver, various frequencies
Removing the door operator takes place in the
reverse sequence of the installation instructions
and must be carried out by qualified technicians.
Dispose of the device according to environmental
guidelines. Electrical parts must not be disposed of
as domestic waste. 2002/96/EG (WEEE)
Operator closes the
door slowly (soft
start) whilst door
operator light flashes
Operator teaches in the travel
automatically. After CLOSED end
position, moves automatically to
OPEN end position. If the door
operator light flashes in intervals of
4, carry outTeaching in the door
operator (Chapter 15)
The operator
switches off during
motion.
Check that the door is running
smoothly and that the entrapment
protection device is working properly
/ Reset / Teach in the door operator
Remote transmitter is
not working, LED not
alight
Replace the batteries
Remote transmitter is
not working If the function message assigned to the transmission pulse is not
displayed whilst the transmitter is
actuated (see Chapter 16): Teach in
remote transmitter / Poor reception
(install optional antenna) energy-
saving lamps
The operator cannot
be used via the wall
keypad (optional).
Check the wall keypad and control
wire.
The operator cannot
be used via the
remote transmitter
(optional).
Radio level too weak. There are
interfering radio signals from other
transmission sources / Carry out
radio level check as described below
23 Maintenance intervals
24 Declaration of conformity
25 Technical data
Mains connection 230 V~, 50/60 Hz
Device fuse 1.6 A, T (slow-blow)
Power consumption at rated load 140 W
Closed current < 2 W
Degree of protection For dry rooms
only, IP 20
Protection class 1
Wireless remote control 433.92 MHz AM
Remote transmitter range 1) 15 - 50 m
Remote transmitter batteries CR 2032 (3 V)
Idle speed ~ OPEN >210 mm/s
~ CLOSE >140 mm/s
Traction 600 N
Rated load 150 N
Stroke length
Magic 600 2890 +/- 25 mm
Magic 600 long 3978 +/- 25 mm
Total length 3) 615 +/- 25 mm
Total length 2) 3) 485 +/- 25 mm
Width 285 mm
Width 2) 363 mm
Installation height drive rail 40 mm
Permissible
ambient temperatures
-20°C to 50 °C
Storage -20°C to 80 °C
Lighting E14, max. 40 W
Maximum number of duty cycles
per hour at rated load 20
Maximum number of duty cycles
without a break at rated load 8
Noise level at a distance of 2 m ≤69 dB(A)
26 Replacement parts
27 Accessories (optional)
28 Removal, Disposal

Magic 600 N000924 12/2010 155 / 208
A
B
C
?
2.
1.

156 / 208 N000924 12/2010 Magic 600
D
E
F
A
BX
1.
1. 2.
A mm
3.492
4.580
4-6
6-9
B mm
0-35cm
3.492 mm
4.580 mm

Magic 600 N000924 12/2010 157 / 208
G
==
A
B5-15mm
C> 100 mm
B
C
B
C
A< 150 mm
A>150 mm

158 / 208 N000924 12/2010 Magic 600
Einbaumaße
D
G3
G2
D
D
G4
D
G1
N001452

Magic 600 N000924 12/2010 159 / 208
H
A
A100 - 150 mm
A150 - 350 mm

160 / 208 N000924 12/2010 Magic 600
I
DE Das zum Tor passende Toranschlussprofil (X) montieren.
Bei notentriegeltem Tor besteht Gefahr durch ungebremste Torbewegungen.
GB Install the door connection profile (X) that matches the door.
Emergency unlocking of the door creates an unchecked door movement hazard
FR Monter le profilé de raccordement adapté à la porte (X).
Une porte ainsi déverrouillée devient dangereuse : ses mouvements ne sont plus freinés.
SE Montera den portanslutningsprofil (X) som passar till porten.
På nödupplåsta portar finns det risk för att portens rörelser inte bromsas in.
DA Monter den porttilslutningsprofil (X), som passer til porten.
Vær opmærksom på eventuelle fare p.g.a. portens frie bevægelighed når nødudløseren er i brug.
NO Monter den tilkoblingsprofil (X) som passer til porten.
Når porten er frikoblet kan det oppstå fare som følge av ukontrollerte portbevegelser.
FI Oveen on asennettava sopiva liitäntäprofiili (X).
Hätäavaustilanteessa saattaa oven hallitsematon liikkuminen vaarantaa turvallisuuden.
NL Monteer het bij de deur passende deuraansluitprofiel (X).
Bij een in noodgeval ontgrendelde deur bestaat er gevaar door ongeremde deurbewegingen.
IT Montare il profilo idoneo del raccordo della porta (X). Se la porta è stata aperta azionando lo sblocco d’emergenza,
esiste il pericolo che la porta esegua movimenti non frenati.
HU A kapuhoz illõ kapucsatlakozási profilt (X) szereljen fel.
Vészkireteszelt kapu esetén veszély áll fenn fékezetlen kapumozgások által.
RU Установить соответствующии воротам присоединительныи профиль (X).
При аварийном отпирании ворот имеется опасность вследствие отсутствия торможения при движении ворот.
PL Zamontowaćkształtownik do mocowania bramy (X) pasujący do typu bramy.
Jeżeli garażnie posiada drugiego wejścia, należy zainstalowaćzewnętrzne otwieranie awaryjne.
SI Montirajte priključni profil vrat (X) primeren za vrata.
Če je odpiralni mehanizem v sili aktiviran, obstaja nevarnost pomikanja vrat brez zaviranja.
CZ Namontovat pripojovací profil vrat, který se hodí pro vrata.
U vrat s nouzovým odblokováním existuje nebezpečí nebržděnými pohyby vrat.
SK Namontuje profil pripojenia brány (X) vhodný pre bránu.
V prípade núdzového otvorenia brány vzniká nebezpečie nebrzdených pohybov brány.
GR Συναρμολογήστε το προφίλ τελειώματος που ταιριάζει στη γκαραζόπορτα (X). Σε περίπτωση που ηπόρτα είναι
απασφαλισμένη με τη διάταξη απασφάλισης ανάγκης, υπάρχει κίνδυνος λόγω μη πέδησης
ES Montar el perfil de conexión (X) adecuado para la puerta.
Con la puerta desbloqueada por emergencia existe peligro a causa de movimientos sin freno de la misma.
PT Monte o perfil de ligação certo para o portão (X).
Se o portão tiver sido desbloqueado de emergência, existe o perigo de ele se deslocar descontroladamente.
BG Указание: Монтирайте подходящ за вратата свързващ профил за врата (X). При врати саварийно
деблокиране съществува опасност от неограничени движения на вратата.
HR Montirajte vratima pripadajući priključni profil vrata (X). Kod vrata koja su otključana u nuždi postoji opasnost radi
kretanja vrata bez kočenja.
RO Montaţi profilul de racordare poartă(X) potrivit porţii. În cazul porţii deblocate de urgenţă existăpericol datorat
mişcărilor nefrânate ale porţii.
AE
ΔΑ΍ϮΒϠϟΔϠϣήϔϤϟ΍ήϴϏ ΔϛήΤϟ΍ϝϼΧϦϣήτΧ ΪΟϮϳ ϪϧΈϓ Ήέ΍ϮσΔϟΎΣϲϓΎϫήϳήΤΗ ϢΗΪϗ ΔΑ΍ϮΒϟ΍ϥϮϜΗΎϣΪϨϋ
ΔΑ΍ϮΒϟ΍ ϞϴλϮΗ ϊτϘϣΐϴϛήΗ ϢΘϳ(X)ΔΑ΍ϮΒϠϟΐγΎϨϤϟ΍.

Magic 600 N000924 12/2010 161 / 208
J
K
DE Notentriegelung intern PL Otwieranie awaryjne wewnętrzne
GB Internal emergency release SI Odpiranje v sili z notranje strani
FR Déverrouillage de secours interne CZ Nouzové odblokování. Vnitřní
SE Intern nödöppning SK Núdzové otvorenie interné
DA Intern frikobling GR Απασφάλιση ανάγκης εσωτερικά
NO Innvendig nødsperre ES Desbloqueo de emergencia interno
FI Sisällä oleva hätävapautin PT Desbloqueio interno de emergência
NL Noodontgrendeling intern BG Вътрешно аварийно деблокиране
IT Sblocco di emergenza interno HR Otključavanje u nuždi od unutra
HU BelsővészkireteszelőRO Deschiderea de siguranţă internă
RU Аварийное отпирающее устройство изнутри AE
ΎϴϠΧ΍Ω Ήέ΍Ϯτϟ΍ΕϻΎΣϲϓήϳήΤΘϟ΍

162 / 208 N000924 12/2010 Magic 600
Lieferumfang
9
9
10
10
4.1
4.3
4.2
5
2
B
6
1.2
1.3
1.9
1.11
1.4
8
1.12
1.6
1.5
1.8
1.1

Magic 600 N000924 12/2010 163 / 208
1.1 N000916-00-00
1.2 N000912-00-00
1.3 T90005
1.4 T14558
1.5 (Stopp) T14743
1.6 (SE) T14742
1.8 N000914-00-00
1.9 * N001495-00-00
1.11 *
Schuko 1000 mm N001415-00-00
GB 1000 mm N001415-00-02
GB 5000 mm N001415-00-03
CH 1000 mm N001415-00-01
1.12 * Euro N001369-00-00
GB N001376-00-00
2
NS N000880-01-00
CR N000880-02-00
EV N00880-03-00
HS N000880-04-00
IN N000880-05-00
NT N000880-06-00
4.1 T14509
4.2 T14600
4.3 N000877-00-00
5
Gr.1 6480 mm N001491-00-00
Gr.2 8664 mm N001492-00-00
Gr.3 10840 mm N001493-00-00
Gr.4 15160 mm N001494-00-00
6 N000907-00-00
8 T14579
9 T14529
10 T14572
B T14526
PL Części zamienne oznaczone * mogąbyćwymieniane
tylko przez personel z odpowiednimi uprawnieniami
zawodowymi.
SI Rezervne dele označene z * smejo zamenjati samo
pooblaščeni strokovnjaki.
CZ Náhradní díly označené * smí vyměnit jen autori-
zovaný personál.
SK Náhradné diely označené * smie vymieňaž výhradne
autorizovaný odborný personál.
GR Τα σημαδεμένα με έναν αστερίσκο (*) ανταλλακτικά
εξαρτήματα επιτρέπεται να αντικατασταθούν μόνο από
εξουσιοδοτημένο ειδικευμένο προσωπικό.
ES Las piezas de repuesto marcadas con * solamente las
puede cambiar personal especializado y autorizado.
PT As peças sobressalentes assinaladas com * só
podem ser substituídas por pessoal técnico autori-
zado.
BG Отбелязаните с* резервни части могат да се
заменят само от упълномощени специалисти.
HR Mijenjanje sa * označenih rezervnih dijelova
dopušteno je samo ovlaštenom stručnom osoblju.
RO Piesele de schimb marcate cu * pot fi schimbate doar
de către personal de specialitate autorizat.
AE
ΓΪϤΘόϣΔμμΨΘϣ ΔϴϨϘΗ ΔϟΎϤϋ.
ΔϣϼόΑ ΓΰϴϤϤϟ΍ έΎϴϐϟ΍ ϊτϗ*ϻ· ΎϫήϴϴϐΘΑ ΢Ϥδϳ ϻ
ϞΒϗ Ϧϣ
DE Die mit * markierten Ersatzteile dürfen nur durch
autorisiertes Fachpersonal gewechselt werden.
GB The spare parts marked with * may be exchanged
only by authorised trained personnel.
FR Le remplacement des pièces de rechange signalées
par * ne doit être effectué que par un personnel
agréé.
SE De med * markerade reservdelarna får endast bytas
av auktoriserat fackfolk.
DA De reservedele, som er markeret med *, må kun uds-
kiftes af autoriseret fagpersonale.
NO Reservedeler som er merket med * må kun skiftes ut
av autorisert fagpersonale.
FI Tähdellä * merkityt varaosat saa vaihtaa ainoastaan
valtuutettu ammattihenkilöstö
NL De met * gemarkeerde reserveonderdelen mogen
alleen door geautoriseerd vakpersoneel vervangen
worden.
IT I ricambi contrassegnati con * possono essere sosti-
tuiti soltanto da personale specializzato autorizzato.
HU A csillaggal (*) jelölt pótalkatrészeket csak arra feljog-
osított szakszemélyzet cserélheti ki.
RU Отмеченные символом * запасные части
разрешается заменять только авторизованным
специалистам.

164 / 208 N000924 12/2010 Magic 600
Sicherung wechseln
1.
2.
3.
5.
S1
S2
4.

Magic 600 N000924 12/2010 167 / 208
EC-Declaration of Conformity
in accordance with the EC-Machinery Directive 2006/42/EG, Appendix II A
GB Translation of the German declaration
We,
Cardo Door Production GmbH
Normstahlstrasse 1-3
D-85368 Moosburg, Germany
hereby declare that the machinery described below complies in its design and
construction and in the version marketed by us with the basic safety and health
requirements of the EC Directive 2006/42/EG.
Product description
Function Electrical garage door operator with radio remote control
Model Magic
Type Magic 600
With following garage door types:
Euroclassic Iso - Euroframe alu - Euroframe copper - Euroframe wood - Euroline Iso - Eurostyle iso - Euroflair Iso -
Eurotrend Iso - Eurotwin Iso - Castell - Elegant - Prominent-F - Klassik - Rustico - S-Castell - S-Elegant -
S-Prominent-F - S-Klassik - S-Rustico - Prominent - Variant - S-Variant - Variant wood - S-Variant Wood - Classic - Style -
Twenty - Topframe - Topclassic iso - Topframe Alu - Topframe Copper - Topflair Iso - Topframe Steel - Topframe wood -
Topline Iso - Topstyle Iso - Toptrend Iso - Toptwin Iso - G60 Classic - G60 Style - G60 Trend - G60 Line - G60 Elipse
Harmonised standards applied
DIN EN ISO 12100-1:2004-04 Safety of machinery – basic concepts, general principles for design – Part 1
DIN EN ISO 12100-2/A1:2009-10 Safety of machinery – basic concepts, general principles for design – Part 2
DIN EN ISO 13849-1:2008-12 Safety of machinery – Safety-related parts of control systems - Part 1
DIN EN 12445:2005-05 Industrial, commercial and garage doors and gates – Safety in use of power operated
doors – Test methods
DIN EN 12453:2005-05 Industrial, commercial and garage doors and gates – Safety in use of power operated
doors - Requirements
DIN EN 13241-1:2004-04 Industrial, commercial and garage doors and gates – Product standard – Products
without fire resistance and smoke control characteristics
Other applied directives
Construction Products Directive 89/106/EWG EMC 2004/108/EG
Low Voltage Directive 2006/95/EG 1999/5/EG R&TTE
The following tests were conducted by these approved bodies:
TÜV SÜD Product Service GmbH
Reg. No. 063795
Ridlerstrasse 65 - D-80339 München, Germany
Mikes
Reg. No. D-PL-12030-01-03
Ohmstrasse 2-4 - D-94342 Straßkirchen, Germany
Test results (passed)
- Safety requirements closing forces
- Electrical safety
- Mechanical requirements
- Electromagnetic compatibility
Person authorised to collect the technical documents: Herbert Dust,
address see above.
Wolfgang Schulz, Managing Director
Moosburg, 01.12.10

168 / 208 N000924 12/2010 Magic 600
Declaration of incorporation
GB Translation of the German declaration
We,
Cardo Door Production GmbH
Normstahlstrasse 1-3
D-85368 Moosburg, Germany
hereby declare that we have applied and complied with the following basic requirements of the EC Directive 2006/42/EG in the
design and manufacture of the partially completed machinery described below: 1.1.2, 1.1.3, 1.2.1, 1.2.3, 1.2.4, 1.2.6, 1.3.2,
1.3.4, 1.5.1, 1.5.2, 1.5.3, 1.5.8, 1.5.9, 1.5.10, 1.5.11, 1.5.9, 1.6.3, 1.7.3, 1.7.4
The special technical documents have been compiled in accordance with Appendix VII Part B of the EC Directive 2006/42/EG.
We undertake to submit these in electronic form to the market supervisory authorities upon demand within a reasonable time.
Description of the partially completed machinery
Function Electrical garage door operator with radio remote control
Model Magic
Type Magic 600
Harmonised standards applied
DIN EN ISO 12100-1:2004-04 Safety of machinery – basic concepts, general principles for design – Part 1
DIN EN ISO 12100-2/A1:2009-10 Safety of machinery – basic concepts, general principles for design – Part 2
DIN EN ISO 13849-1:2008-12 Safety of machinery – Safety-related parts of control systems - Part 1
DIN EN 13241-1:2004-04 Industrial, commercial and garage doors and gates – Product standard – Products
without fire resistance and smoke control characteristics
Other applied directives
Construction Products Directive 89/106/EWG EMC 2004/108/EG
Low Voltage Directive 2006/95/EG 1999/5/EG R&TTE
The following tests were conducted by these approved bodies:
TÜV SÜD Product Service GmbH
Reg. No. 063795
Ridlerstrasse 65 - D-80339 München, Germany
Mikes
Reg. No. D-PL-12030-01-03
Ohmstrasse 2-4 - D-94342 Straßkirchen, Germany
Test results (passed)
- Safety requirements closing forces
- Electrical safety
- Mechanical requirements
- Electromagnetic compatibility
The partially completed machinery may not be put into operation until it has been determined that the machinery into which the
partially completed machinery is to be installed complies with the regulations of the Machinery Directive.
Wolfgang Schulz, Managing Director
Moosburg, 01.12.10