HEPER Rhino Flood Installation and operating instructions

2xM8 Allen HeadBolts
1
4
2
5
6
3
1.
1.1 lb ft
Rhino Flood (Side Mount)
Installation&Maintenance Instructions
REV 1/07.27.2021
1.
3.
2xM4 Phillips Head Bolts
2xM4 Lock Washers
1.
2.
4.5 lb ft
S6
2.
1.
M10 Allen Head Bolts
30 lb ft
S8
4.5 lb ft
S4
2.
3.
2xM8Allen Head Bolts
15 lb ft
S6
2.
1.
2.
4xM6 Countersunk Head Bolts
±80°
±45°
HEPER USALLC
W227 N546 Westmound Drive
WaukeshaWI 53186 – USA
Tel: [phone]
[e-mail]
www.heperlighting.com

ØA
(Inch)
B
(Inch)
C
(Inch)
D
(Inch)
E
(Inch)
F
(Inch)
WEIGHT
(lb)
PRODUCT
CODE
10 15/16
1 17/32
15 5/32
3 15/16
7 3/32
5 1/8
16.5
LL2028.694
7
3.
8
1.
2.
4xM5 Allen Head Bolts
1.
2.
S8
3.5 lb ft
S4
3 lb ft
2xM5 Nuts
2xM5 Washer
* EYE SAFETY WARNING
Lighting luminaire is classified under “EXEMPT GROUP”
according
to photobiological safety standard IEC/EN 62471. NO RISK for
the
operators and end-users.
English
ASSEMBLY INSTRUCTIONS
Mounting Luminaire to Pole;
1. To Install the Rhino Floodlight Luminaire on pole;
1.1. Make supply wire connection and pass cable through grommet on pole.
1.2. Align holes in luminaire base plate with threaded holes on pole.
1.3. Install (2) M8 bolts using size S6 Allen Head wrench. Tighten to 15 lb ft (20
Nm) of torque
2. Adjusting Tilt Angle;
2.1. Loosen (do not remove) M10 bolt and M10 nut using size S8 Allen Head wrench.
2.2. Adjust Luminaire head to desired tilt angle. Approximate range of tilt adjustment + 80
Degrees. Tighten bolt/nut to 30 lb ft (40 Nm) of torque.
3. Base/Orientation Adjustment;
3.1. Loosen (do not remove) (2) M8 bolt and washer assemblies using size S6 Allen
Head wrench.
3.2. 3.2 Select desired horizontal arm rotation adjustment. Approximate range of adjustment
± 45 Degrees. Tighten bolt to 15 lb ft (20 Nm) of torque.
LED Driver Replacement;
Note 1: Ensure power is off/disconnected from the source
Note 2: For Personnel and Luminaire safety, remove luminaire from pole and carry out
maintenance at grade.
4. Accesing LED Driver;
4.1. Remove (4) M6 Countersunk Allen Head bolts holding front cover/visor assembly
in place using S4 Allen wrench. Replacement torque spec for bolts 4.5 lb ft (6 Nm).
4.2. Gently remove complete assembly containing cover/ visor, LED Module and driver.
5.5. Carefully disconnect supply power socket from cover/visor, LED Module and driver
assembly.
Note 1: Be careful not to damage the LED driver
Note 2: Be careful not to damage the wire connectors
6.6. To remove LED driver from module assembly;
6.1. Carefully disconnect wire connectors between LED Driver and LED light module.
Note: Be careful not to damage the LED driver and sockets.
6.2. Remove (2) Phillips Head bolts and lock washers. Replacement torque spec 1.1
lb ft (1.5 Nm).
6.3. LED Driver is now free and can be removed from assembly.
7. To remove complete LED Module and driver assembly from cover/visor assembly;
7.1. Remove (2) M5 nuts and flat washers. Replacement torque spec 3 lb ft (4 Nm).
7.2. LED Lighting module and LED driver assembly are now freed from cover/visor
assembly.
7.3. Carefully disconnect wire connectors between LED Driver and LED light module.
Note: Be careful not to damage wire connectors.
Replacing LED Light module;
Note: Remove Driver and LED light module assembly by following all notes and steps
from LED driver replacement through step 7.3 above. Be careful not to damage any
wire connector assemblies.
8. Dismantling the LED Light engine;
8.1. Remove (4) M5 Allen Head bolts attaching driver bracket to LED light engine heat
sink using S4 Allen wrench. Replacement torque spec 3.5 lb ft (5 Nm)
8.2. LED Light module and heat sink are now free to be removed from LED Driver bracket.
Note: Be careful not to damage LED driver or Light Engine during replacement process.