hestan KIC 30 User manual

INDOOR COOKING
Induction Cooktop
KIC
Installation Manual

©2018 Hestan Commercial Corporation
2
EN
SAFETY DEFINITIONS
THIS INDICATES THAT DEATH OR SERIOUS INJURY MAY
OCCUR AS A RESULT OF NOT OBSERVING THIS WARNING
THIS INDICATES THAT MINOR OR MODERATE INJURY MAY
OCCUR AS A RESULT OF NOT OBSERVING THIS WARNING.
THIS INDICATES THAT DAMAGE TO THE APPLIANCE OR
PROPERTY MAY OCCUR AS A RESULT OF NOT OBSERVING
THIS WARNING.
CAUTION
READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY
BEFORE INSTALLING OR USING YOUR APPLIANCE TO REDUCE
THE RISK OF FIRE, BURN HAZARD, OR OTHER INJURY. KEEP THIS
MANUAL FOR FUTURE REFERENCE.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance.
Installation and service must be performed by a qualified installer or service agency.
DO NOT REPAIR, REPLACE OR REMOVE ANY PART OF THE APPLIANCE UNLESS
SPECIFICALLY RECOMMENDED IN THE MANUAL. IMPROPER INSTALLATION,
SERVICE OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE. REFER
TO THIS MANUAL FOR GUIDANCE. ALL OTHER SERVICING SHOULD BE DONE BY A
QUALIFIED TECHNICIAN.
INSTALLER: LEAVE THIS MANUAL WITH THE OWNER OF THE APPLIANCE.
HOMEOWNER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED
EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING
PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

©2018 Hestan Commercial Corporation
1
EN
When properly cared for, your Hestan appliance will provide safe, reliable service for many
years. When using this appliance, basic safety practices must be followed as outlined below.
IMPORTANT: Save these instructions for the local Utility Inspector’s use.
INSTALLER: Please leave these Installation Instructions with the owner.
OWNER: Please retain these Installation Instructions for future reference.
This appliance is NOT designed for installation in manufactured (mobile) homes or
recreational park trailers. Do NOT install this appliance outdoors.
SAFETY PRECAUTIONS - BEFORE YOU BEGIN
ELECTRICAL SHOCK HAZARD
Disconnect power before installing or servicing appliance. Failure to do so
can result in death or electrical shock.
ELECTRICAL GROUNDING
• This appliance must be grounded. Grounding reduces the risk of electric shock in the
event of a short circuit. Read the ELECTRICAL CONNECTIONS section of this manual
for complete instructions.
• DO NOT ground to a gas pipe.
• DO NOT use an extension cord with this appliance.
• DO NOT have a fuse in the NEUTRAL or GROUNDING circuit. A fuse in the NEUTRAL
or GROUNDING circuit could result in an electrical shock.
TABLE OF CONTENTS
1 SAFETY PRECAUTIONS - BEFORE YOU BEGIN
2 MODEL NUMBERS
2 RATING LABEL
2 REGULATORY / CODE REQUIREMENTS
3 CUTOUT DIMENSIONS AND REQUIREMENTS
6 COOKTOP INSTALLATION
10 ELECTRICAL CONNECTIONS
12 FINAL SETUP
13 PARTS LIST
13 SERVICE

©2018 Hestan Commercial Corporation
2
EN
MODEL NUMBERS
RATING LABEL
The rating label contains important information about your Hestan appliance such as the model
and serial number, electrical rating and the minimum installation clearances.
The rating label is located on the bottom of the cooktop.
If service is necessary, contact Hestan Customer Care with the model and serial number
information shown on the label.
OVEN MODELS
MODEL NO. DESCRIPTION CIRCUIT BREAKER
REQ’D
KIC 30 30” Induction Cooktop 40 Amp
KIC 36 36” Induction Cooktop 50 Amp
REGULATORY / CODE REQUIREMENTS
Installation of this cooking appliance must be made in accordance with local codes. In the
absence of local codes, this unit should be installed in accordance with the National Electrical
Code and local codes.
This appliance must be electrically grounded in accordance with local codes or in the absence
of local codes with the National Electrical Code
ANSI/NFPA 70 , or Canadian Electrical code
CSA C22.1 .
Location of rating label
KIC30-BK
HESTAN COMMERCIAL CORP.
ANAHEIM, CA - USA
TYPICAL RATING LABEL

©2018 Hestan Commercial Corporation
3
EN
30”
30” 3/8
[771 mm]
21” 3/16
[538 mm]
1/4”
[6mm]
2” 5/8
[66 mm]
1” 1/16
[27 mm]
36”
36” 3/16
[919 mm]
21” 3/16
[538 mm]
1/4”
[6mm]
2” 5/8
[66 mm]
1” 1/16
[27 mm]
CUTOUT DIMENSION
LENGTH OF CUT
A
LENGTH OF CUT
B
1-1/2” [3.8cm]
MIN CLEARANCE
SEE NOTE
R
FROM EDGE OF CUTOUT
TO FRONT EDGE OF
COUNTERTOP
2-1/2” [6.5 cm]
CUTOUT DIMENSIONS AND REQUIREMENTS

©2018 Hestan Commercial Corporation
4
EN
D
G
C
E
F
Cutout width D E F G
30”
[76.2cm] 18” [45.7 cm] min
Height from counter-
top to nearest cabinet
on either side of unit
2” [5 cm] min Clearance
from cutout to side wall
on the left and right of
the unit
13” [33 cm] Depth
of unprotected
overhead cabinets
36”
[91.4cm]
Cutout width A B C
30”
[76.2cm]
28-3/4” +/- 1/16”
[73.0 cm +/- 0.1cm]
19-7/16” +/- 1/16”
[49.4cm +/- 1mm]
30”
[76.2cm] min
36”
[91.4cm]
34-5/8” +/- 1/16”
[87.9 cm +/- 0.1cm]
19-7/16” +/- 1/16”
[49.4cm +/- 1mm]
36”
[91.4cm] min
NOTE: 24” [61 cm] min. clearance if bottom of wood or
metal cabinets is protected by not less than 1/4” [0.6 cm]
flame retardant millboard covered with no less than No. 28
MSG sheet steel 0.015” [0.04 cm] stainless steel, or 0.024”
[0.06 cm] aluminum or 0.020” [0.05 cm] copper. 30” [76.2
cm] min. clearance between top of cooking platform and
bottom of unprotected wood or metal cabinet.
Under the cooktop it is necessary to install a
partition, as shown.
WALL COVERING CABINETS,
AND COUNTERTOP MUST
WITHSTAND HEAT UP TO 200° F [93° C]
CUTOUT REQUIREMENTS
30” [76.2 cm] min.
[see note*] Clearance
from countertop to
unprotected
overhead surface
NOTICE
CUTOUT DIMENSIONS AND REQUIREMENTS (CONT.)

©2018 Hestan Commercial Corporation
5
EN
min
Important Preparation Suggestions
1. Chamfer all exposed edges of decorative laminate to
prevent damage from chipping.
2. Radius corners of cutout and file to ensure smooth edges
and prevent corner cracking. Recommend 1/4” or 3/8”
diameter drill to start cut at each corner.
3. Rough edges, inside corners which have not been rounded
and forced fits can contribute to cracking of the countertop
laminate.
VERTICAL CLEARANCES
* The ventilation opening is to extend the full length of the cooktop cutout.
25”[635 mm]
min
”
2 1/2”
[64mm]
3
”
[76 mm]
2 1/2”
[65 mm]
1 5/8”
[40 mm]
max
1/4”
[6 mm]
min
36”
[915 mm]
24”[610 mm]
15 3/4”
[400 mm]
5”
[127 mm]
min
*1/4”
[6 mm]
min
min
19 7/16 [494 mm]
1 1/2
4 3/4
[120 mm]
[38 mm]
min
”
”
4”
[101 mm]
min
Partitian
CUTOUT DIMENSIONS AND REQUIREMENTS (CONT.)

©2018 Hestan Commercial Corporation
6
EN
COOKTOP INSTALLATION
CAUTION
EXCESSIVE WEIGHT HAZARD
Use two or more people to move and install cooktop. Failure to do so can result in back
or other injury.
CUT HAZARD
Beware of sharp edges. Use the polystyrene ends when carrying the product. Failure to
use caution could result in minor injury or cuts.
Always consult the countertop manufacturer for specific instructions.
• Ensure the countertop is square and level and ensure no structural members interfere with
space requirements.
• Prepare the cut-out according to the instructions (see cut-out dimensions).
• Make sure the wall coverings, countertop and cabinets around the cooktop can withstand heat
(up to 200° F / 93°C).
STEP 1
Remove packaging materials and literature
package from the cooktop before beginning
installation. Remove Installation Manual from
literature pack and read them carefully before
you begin.
TOOLS WILL YOU NEED
PARTS
COOKTOP
CARDBOARD
TOP-CARDBOARD
MANUAL
GASKET
SCRAPER
TOP PACKAGING
BOTTOM PACKAGING
COOKTOP HOUSING
TABLE CLOTH

©2018 Hestan Commercial Corporation
7
EN
COOKTOP INSTALLATION (CONT.)
STEP 3
A foam tape is provided to seal the cooktop edges to the countertop. Apply tape approximately
1/16” (1.5 mm) from the glass edge to the underside of the cooktop glass. Use tape around the
entire glass perimeter. Cut off excess where tape ends butt.
STEP 4
Insert the cooktop centered into the cutout opening. Make sure the front edge of the counter top
is parallel to the cooktop.
Make a final check that all required clearances are met.
STEP 5
Four or six clamp brackets are provided to clamp the cooktop to the countertop. Tighten screws
just enough to hold brackets in place when cooktop is put into cutout.
When all brackets are in place, tighten screws securely.
COOKTOP HOUSING
COO KTOP GLASS
FOAM TAPE SEAL

©2018 Hestan Commercial Corporation
8
EN
COOKTOP INSTALLATION (CONT.)
ELECTRIC OPENING
NOTICE
• THE ELECTRICAL CONDUIT IS 3 FEET
LONG.
• The junction box must be located where
it will allow considerable slack in the
conduit for serviceability.
NOTICE
• For solid surface material installations
such as Surel™ and Corian®, consult
with solid surface manufacturer. Apply
heat reflective tape such as Scotch®
Aluminum Foil Tape #425 or #427 around
the cutout so that it folds over on the top
and sides.
• Do not wrap the tape underneath the
cooktop.
• Be sure the tape extends beyond the
outermost flange of the cooktop. All
corners should be covered with tape.

©2018 Hestan Commercial Corporation
9
EN
*The ventilation opening is to extend the full length of the cooktop cutout.
4”
[101mm]
min
24”[610mm]
min
36”
[915 mm]
25”[635 mm]
min
19 7/16”[494 mm]
3”
[76 mm]
[64mm]
2 1/2”
1/4”
[6mm]
min
2 1/2”
[65 mm]
27 1/4”
[692 mm]
4 3/4”
[120 mm]
1 1/2”
[38 mm]
min
1 5/8”
[40 mm]
max
*1/4”
[6 mm]
min
COOKTOP INSTALLATION (CONT.)
NOTICE
Use the countertop opening dimensions that are given with these Instructions.
• Check the cooktop base for an approved installation label. Verify approved oven model
numbers that can be installed with your cooktop model number.
• The cooktop may be installed over a single oven.
• The cooktop should be centered over the oven.
• Both the cooktop and the oven must be installed according to each specific installation
instruction.

©2018 Hestan Commercial Corporation
10
EN
Disconnect power before servicing the product.
Failure to do so could result in death or electrical shock.
General information
Themodels may be powered at 240V or208V.
This cooktop does not require a neutral connection. If
the cooktop is to be completely enclosed in a cabinet,
feed the cooktop cable through the opening in the
cabinet. Make the electrical connection following the
appropriate steps for your installation.
Your cooktop must be connected to the proper
electrical voltage and frequency as specified in the
table on the right.
Location of serial tag
The flexible conduit (supplied) 3 feet long (100 cm)
located at the right rear of the cooktop bottom box
should be connected directly into a junction box. Do
not cut the conduit. A U.L - or CSA - listed conduit
connector must be provided at each end of the power
supply cable (at the cooktop and at the junction box.)
A time delay fuse or circuit breaker is recommended.
Do not ground to a gas pipe. Do not have a fuse in the
grounding or neutral circuit.
Fuse both supply (phase) lines.
Improper connection of aluminum house wiring to the
copper leads can result in a serious problem such as an
electrical fire.
Model Power Supply
240 V 60 Hz 208 V 60 Hz Approval
code
30”KIC30 7.2 kW 30A 6.45 kW 31A 815T40*T
36”KIC36 10.8 kW 45A 9.4 kW 45A 815V50*U
National Fire Protection Association Batterymarch
Park, Quincy, Massachusetts 02169-7471
A three-wire, single phase, 240 Volt 60 cycle electrical
system (properly circuit protected to meet Local
Codes of NFPA No.70) must be provided. Unit must
be properly grounded in accordance with local wiring
code. The chart below recommends the minimum
circuit protector and wire size if the appliance is the
only unit on the circuit. If smaller sizes of wire are
used, the unit efficiency will be reduced and a fire
hazard may be created. It is advisable that the electrical
wiring and hookup be accomplished by a competent
electrician.
Amperes
kW Rating on
serial plate
Wire size
(AWG)
0-4.8 20 12
4.9-6.9 30 10
7.0-9.9 40 8
10.0-11.9 50 8
12.0-14.9 60 6
Be sure your appliance is properly installed and
grounded by a qualified technician. Ask your dealer to
recommend a qualified technician or an authorized
repair service. This cooktop does not require a neutral
connection. If the cooktop is to be completely
enclosed in a cabinet, feed the cooktop cable through
the opening in the cabinet. Make the electrical
connection following the appropriate steps for your
installation.
Recommended Minimum Circuit protection
NOTICE
NOTICE
ELECTRICAL CONNECTIONS

©2018 Hestan Commercial Corporation
11
EN
ELECTRICAL CONNECTIONS (CONT.)
3
-Wire branch circuit
W
here local codes allow the connection of ground wire from
t
he cooktop to the branch circuit neutral wire (gray or white
c
olored wire) proceed as follows.
1
. If local codes permit, connect the green GROUND wire
from the cooktop to the branch circuit neutral wire (gray or
white colored wire).
2
. Connect the red and black leads from the cooktop to the
corresponding leads in the junctionbox.
Cable from power supply
Red Wires
White Wires
Bare or green wires
3-Wire cable from cooktop
Where local codes permit connecting the frame-ground
conductor to the neutral (white) junction box wire.
(Not used for Canadian installations)
Junction box
Twist-on connector
Black wires
U.L.-or CSA-listed conduit connector
4--Wire branch circuit
1. Connect the green ground wire from the cooktop to th
e
ground wire in the junction box (bare or green colored
wire).
2. Connect the red and black leads from the cooktop to the
corresponding leads in the junction box.
3. Terminate and insulate the neutral (gray or white colored
wire) in thejunction box.
Red wires
Bare or green wires
3-Wire cable from cooktop
Twist-on
connector
Black wires
U.L. - or CSA-listed conduit connector
Junction box
White wire
Cable from power supply
This appliance is manufactured with a green ground wire connected to the cooktop chassis. After making sure that the power
h
as been turned off, connect the flexible conduit from the cooktop to the junction box using a U.L. listed conduit connector. The
i
nstructions provided below present the most common way of connecting the cooktops. Your local codes and ordinances, of course,
t
ake precedence over these instructions. Complete electrical connections according to local codes and ordinances.
Risk of Electric Shock, frame grounded to neutral of appliance throughalink.
Gro
unding through the neutral conductor is prohibited for new branch-circuit installations (1996 NEC); mobile homes; and
r
ecreational vehicles, or in an area where local codes prohibit grounding through the neutral conductor.

©2018 Hestan Commercial Corporation
12
EN
FINAL SETUP
CLEANUP, VERIFY POWER
Remove any final packaging materials and protective film from all exterior areas.
Check the electrical requirements for the correct electrical supply and that the cooktop is properly
grounded.
Check power at the junction box wires using a voltmeter having a range of 0-250 VAC.
• A 240 Volt supply should read 220 to 240 Volts between the black and red wires (Line to Line).
• A 208 Volt supply should read 190 to 208 Volts between the black and red wires.
FUNCTIONAL TEST
1. Fill an induction-capable cooking utensil with 1/2 - 1” [1.2-2.5 cm] of water and place it on one
of the cooking zones.
1. Switch the Control ON by touching the [ON OFF] key(1).
• If the commands are locked, touch the
lock key(2) for a few seconds. (See
that the LOCK indicator (3) is on and
turns off after a few seconds.) Then the
controls should respond.
2. Touch the zone select key (6) for the
cook zone where the utensil is.
3. Touch the power slider for that zone
and set it to a level between 3 and 9.
4. Observe that the display responds to
the power setting, and observe that the
cooking utensil begins to heat up.
5. Touch the selector key (6) for that zone to turn it off.
6. Touch the [ON OFF] key to turn the cooktop off.
Item Function Item Function
1POWER key 7Power slider - minimum power
2LOCK key 8Power slider - maximum power
3LOCK indicator 9Select Power Booster
4PAUSE key 10 Cooking zone level display
5Pause and Recall involuntary switch-off indicator 11 Power level indicator
6Cooking zone selector (zone ON/OFF) 12 Cooking zone indicator
CRITERIA
If the controls respond as described and the utensil heats up, then the test is successful.
1893 4 5 67
1011
2
12

©2018 Hestan Commercial Corporation
13
EN
SERVICE
All warranty and non-warranty repairs should be performed by qualified service personnel. To locate
an authorized service agent in your zone, contact your Hestan dealer, local representative, or the
manufacturer. Before you call, please have the model number and serial number information ready.
Hestan Commercial Corporation
3375 E. La Palma Avenue
Anaheim, CA 92806
[phone]
PARTS LIST
Please visit the Hestan website to access the parts list for your Hestan Indoor product:
www.hestanhome.com.

LISEZ ATTENTIVEMENT ET COMPLÈTEMENT CES INSTRUCTIONS
AVANT D’INSTALLER OU D’UTILISER VOTRE APPAREIL AFIN DE
RÉDUIRE LES RISQUES D’INCENDIE, DE BRÛLURE OU D’AUTRES
BLESSURES. CONSERVER CE MANUEL POUR RÉFÉRENCE
FUTURE.
DÉFINITIONS DE SÉCURITÉ
PRÉCAUTION
INSTALLATEUR: LAISSER CE MANUEL AVEC LE PROPRIÉTAIRE DE L’APPAREIL.
PROPRIÉTAIRE: CONSERVEZ CE MANUEL POUR RÉFÉRENCE FUTURE.
Ne pas entreposer ni utiliser de I’essence ni d’autres vapeurs ou liquides inflammables dans Ie
voisinage de l’apparell, ni de tout autre appareil.
L’installation et l’entretien doivent être effectués par un installateur qualifié, ou une agence de
service.
NE PAS RÉPARER NI REMPLACER DES PIÈCES DE I´APPAREIL À MOINS QUE CELA NE
SOIT EXPRESSÉMENT RECOMMANDÉ DANS LE MANUEL. TOUTE INSTALLATION,
RÉPARATION OU MAINTENANCE INADÉQUATE PEUT ENTRAÎNER DES BLESSURES OU
DES DOMMAGES MATÉRIELS. CONSULTER CE MANUEL POUR OBTENIR DES CONSEILS
SUR LA FAÇON DE PROCÉDER. TOUS LES TRAVAUX D‘ENTRETIEN DOIVENT ÊTRE
CONFIÉS À UN TECHNICIEN QUALIFIÉ.
L’INOBSERVATION DES INFORMATIONS DONNÉES DANS CE
MANUEL PEUT ENTRAÎNER UN INCENDIE OU UNE EXPLOSION DE
NATURE À CAUSER DES DÉGÂTS MATÉRIELS ET DES BLESSURES
GRAVES, VOIRE MORTELLES.
CECI INDIQUE QUE L’INOBSERVATION DE CET
AVERTISSEMENT PEUT ENTRAÎNER DES BLESSURES GRAVES
VOIRE MORTELLES.
CECI INDIQUE QUE L’INOBSERVATION DE CET
AVERTISSEMENT PEUT ENTRAÎNER DES BLESSURES MINEURES
OU MODÉRÉES.
CECI INDIQUE QUE L’INOBSERVATION DE CET
AVERTISSEMENT PEUT ENTRAÎNER DES DOMMAGES DE
L’APPAREIL OU DES DÉGÂTS MATÉRIELS.

FR
©2018 Hestan Commercial Corporation
1
S’il est bien entretenu, cet appariel Hestan procurera un service sûr et fiable pendant de nombreuses
années. Lorsqu’on se sert de cet appareil, les pratiques élémentaires suivantes en matière de sécurité
doivent être adoptées.
IMPORTANT: Conservez ces instructions pour l’utilisation locale des services publics.
INSTALLATEUR: Veuillez laisser ces instructions d’installation avec le propriétaire.
PROPRIÉTAIRE: Veuillez conserver ces instructions d’installation pour référence future.
Cette cuisinière est conçue pour un usage domestique uniquement. Elle ne l’est PAS pour être
installée dans des maisons préfabriquées (mobiles) ou dans des véhicules récréatifs. N’installez PAS
cette cuisinière à l’extérieur.
PRÉCAUTIONS DE SÉCURITÉ - AVANT DE COMMENCER
RISQUE DE CHOC ÉLECTRIQUE
Débranchez l’alimentation avant d’installer ou d’entretenir l’appareil. Ne pas
le faire peut entraîner la mort ou un choc électrique.
MISE À LA TERRE ÉLECTRIQUE
Cet appareil doit être mis à la terre. La mise à la terre réduit le risque de choc électrique en
cas de court-circuit. Lisez la section BRANCHEMENTS ÉLECTRIQUES de ce manuel pour des
instructions complètes.
• NE PAS broyer sur un tuyau de gaz.
• N’utilisez PAS de rallonge avec cet appareil.
• N’ayez PAS de fusible dans le circuit NEUTRE ou TERRE. Un fusible dans le circuit NEUTRE
ou MISE A LA TERRE pourrait entraîner un choc électrique.
TABLES DES MATIERES
1 PRÉCAUTIONS DE SÉCURITÉ - AVANT DE COMMENCER
2 NUMÉROS DE MODÈLE
2 PLAQUE SIGNALÉTIQUE
2 RESPECT DE LA RÉGLEMENTATION ET DES CODES EN VIGUEUR
3 DIMENSIONS DU PRODUIT ET EXIGENCES DE DÉCOUPE
5 INSTALLATION DE LA TABLE DE CUISSON
8 CONNEXIONS ELECTRIQUES
13 CONFIGURATION FINAL
13 LISTE DES PIÈCES
13 SERVICE

FR
©2018 Hestan Commercial Corporation
2
NUMÉROS DE MODÈLE
PLAQUE SIGNALÉTIQUE
La plaque signalétique donne des informations importantes sur cet appareil Hestan telles que les
numéros de série et de modèle et les dégagements minima d’installation.
La plaque signalétique est située sous l’unité.
Si un entretien est nécessaire, contactez le service clientèle de Hestan avec les informations sur le
modèle et le numéro de série figurant sur la plaque.
RESPECT DE LA RÉGLEMENTATION ET DES CODES EN VIGUEUR
EMPLACEMENT DE LA PLAQUE SIGNALÉTIQUE
MODÈLES DE FOUR
MODEL NO. DESCRIPTION DISJONCTEUR
REQUIS
KIC 30 , 30 po *** Ampères
KIC 36 , 36 po *** Ampères
L’installation de cet appareil de cuisson doit être effectuée conformément aux codes locaux. En
l’absence de tels codes, installer cet appareil conformément au National Electrical Code et les codes
locaux.
Tous les composants électriques doivent mis à la terre conformément aux codes locaux ou, en
l’absence de tels codes, au National Electrical Code ANSI/NFPA 70 ou au Code national de
l’électricité du Canada CSA C22.1.
KIC30-BK
HESTAN COMMERCIAL CORP.
ANAHEIM, CA - USA
PLAQUE SIGNALÉTIQUE TYPIQUE

FR
©2018 Hestan Commercial Corporation
3
DIMENSIONS DU PRODUIT ET EXIGENCES DE DÉCOUPE
30”
36”
DIMENSION DE LA DÉCOUPE
30” 3/8
(771 mm)
21” 3/16
(538 mm)
1/4”
(6mm)
2” 5/8
(66 mm)
1” 1/16
(27 mm)
36” 3/16
(919 mm)
21” 3/16
(538 mm)
1/4”
(6mm)
2” 5/8
(66 mm)
1” 1/16
(27 mm)
LONGUEUR DE DÉCOUPE
A
LONGUEUR DE DÉCOUPE
B
1-1/2” (3.8CM)
ESPACE MINIMUM
VOIR NOTE
R
DU BORD DE LA DÉCOUPE
AU BORD ANTÉRIEUR DU
PLAN DE TRAVAIL
2-1/2” (6.5 cm)

FR
©2018 Hestan Commercial Corporation
4
DIMENSIONS DU PRODUIT ET EXIGENCES DE DÉCOUPE (SUITE)
DISPOSITIONS POUR LA DÉCOUPE
D
G
C
E
F
LES REVETEMENTS DES MEUBLES ET LE
PLAN DE TRAVAIL DOIVENT RESISTER A
UNE CHALEUR DE 93° C [200° F]
Découpe largeur A B C
30”
[76,2cm]
28-3/4” +/- 1/16”
[73,0 cm +/- 0,1cm]
19-7/16” +/- 1/16”
[49,4 cm +/-1mm]
30”
[76,2 cm] min
36”
[91,4cm]
34-5/8” +/- 1/16”
[87,9 cm +/- 0,1cm]
19-7/16” +/- 1/16”
[49,4 cm +/-1mm]
36”
[91,4 cm] min
Découpe largeur D E F G
30”
[76,2cm] 18”
[45,7 cm] min
Hauteur min. du plan de
travail au meuble le plus
près des deux cotés de
l’appareil
30”
[76,2 cm] min.
(voir note*) Du plan de
travail à lasurface non
protégéeà la verticale
2”
[5 cm] min
Espace min. de la
découpe à la paroi
latérale sur la gauche et
la droite de l’appareil
13”
[33 cm]
Profondeur des
meubles non
protégées à la
verticale
36”
[91,4cm]
En dessous de la table de cuisson, il est nécessaire d’installer
unecloison.
NOTE: 24” [61 cm] espace min. si le bas des meubles en bois
ou en métal est protégée par au moins 1/4“ [0,6 cm] de
carton-reliure ignifuge avecunetôled’acierinoxydable No.
28 MSG d’au moins 0,015” [0,04 cm], ou d’aluminium
0.024” [0,06 cm] ou de cuivre 0.020” [0,05cm].
30” [76,2 cm] d’espace min. entre le haut de la plate-
forme de cuisson et le bas du meuble non-protégé en boi
s
ou métal.
AVIS