Hewlett Packard Enterprise StoreOnce 3620 Guide

HPE StoreOnce 3620 and
3640 Systems Start Here
Guide
© Copyright 2018 Hewlett Packard Enterprise Development LP
*BB954-80005*
Part Number: BB954-80005
Published: September 2018
Edition: 1
Abstract
This guide describes how to install a basic HPE
StoreOnce 3620 or 3640 System that does not include
optional storage products. The StoreOnce System can
then be fully configured using the StoreOnce
Management Console, as described in the HPE
StoreOnce 3620, 3640, 5200, 5250, and 5650 Systems
Installation Guide.
Use this guide when installing a basic system without
optional storage products and with all PCIe cards pre-
installed. PCIe cards that were ordered with the system
are pre-installed.
Use the HPE StoreOnce 3620, 3640, 5200, 5250, and
5650 Systems Installation Guide in the following cases.
• The system includes optional storage products or
capacity upgrade kits.
• The system arrived without PCIe cards pre-installed
or requires additional PCIe cards.
Process overview
Required tools:
• Torx T25 screwdriver
• A monitor and USB keyboard or a KVM for initial
network configuration
Procedure
1. Verify the contents
2. Record the iLO default network information
3. Install the components in the rack
4. Attach the security bezel
5. Connect the system cables
6. Power up
7. Configure iLO during bootup (optional)
8. Configure the basic network
9. Configure the StoreOnce System
Verifying contents
Procedure
1. Verify that you received the following items:
• StoreOnce System
• Rail kit
• Security bezel
Page 1

• Two power cables
• Two network cables
Recording the iLO default network
information
Procedure
Record the iLO default network information from the
label on top of the server node.
iLO user name:________________________
iLO network name:_____________________
iLO password:_________________________
Installing the server in the rack
CAUTION: Use extreme caution when installing
and pulling units from the rack. Unattached units
can slip and fall, damaging the StoreOnce System
or causing personal injury. Hewlett Packard
Enterprise is not responsible for any damage or
injury caused by mishandling the StoreOnce
System.
Always use at least two people to lift and locate an
enclosure into the rack.
Procedure
1. Install the rail kit for the StoreOnce server. See the
installation instructions that ship with the rail kit.
2. Insert the two locking nuts for the server into the rack;
one on each front column.
3. Install the server into the rack and secure it using the
thumbscrews on the front bezel of the server.
Attaching the security bezel
Procedure
1. Insert the security bezel right tab into the slot on the
chassis and then rotate the bezel to close.
2. Lock the bezel.
The key to lock the bezel is attached to the back of
the security bezel. One key is supplied.
Connecting the system cables
Procedure
1. Connect the power cables.
Connect each power cable to a separate PDU in the
rack.
2. Connect a network cable to LAN port 1.
3. Connect a network cable to the iLO port
(recommended).
4. If you are not using iLO for initial configuration,
connect a VGA monitor and a USB keyboard.
Powering on the system
Prerequisites
All storage enclosures must be installed and cabled
before the system is powered on. For instructions about
installing optional storage enclosures, see the HPE
StoreOnce 3620, 3640, 5200, 5250, and 5650 Systems
Installation Guide.
Page 2

Procedure
Power on the StoreOnce System (the power button is on
the front of the server).
The power button LED flashes green at the start of the
power-on sequence and then turns solid green, along
with the system health LED. If LAN port 1 is connected
to an active link, the NIC status LED will also begin to
flash green when the StoreOnce System is powering up.
While configuring the system using iLO virtual console,
the UID LED flashes blue.
1. Power LED and on/off button
2. NIC status LED
3. System health LED
4. UID LED
After successful bootup, the console displays a login
prompt.
Configuring iLO during bootup (optional)
Procedure
1. Press F9 System Utilities.
2. Navigate to System Configuration > iLO 5
Configuration > Network Options.
3. Configure the iLO network options and note the
details.
iLO IP address:___________________________
iLO subnet mask:_________________________
iLO gateway:_____________________________
Configuring the basic network
Procedure
1. Log in using the default user name and password.
Default user name: console
Default password: changeme
2. Change the console password to proceed.
Choose a secure password with at least eight
characters that is memorable to you.
3. To configure a static address for LAN port 1 (eno1),
select the Configure initial network option
from the console menu.
Note the DHCP assigned IP address or the static
address details.
IP address:______________________________
Prefix length:_____________________________
Gateway:________________________________
DNS:___________________________________
Configuring the StoreOnce System
The StoreOnce System is now accessible on the
network and ready for configuration.
Procedure
Use the First Time Setup wizard to configure the system
for use. The wizards runs automatically the first time a
user browses to the system IP address.
For configuration instructions, see the HPE StoreOnce
3620, 3640, 5200, 5250, and 5650 System Installation
Guide.
Finding StoreOnce documents in the HPE
Information Library
The latest product documentation is available in the
StoreOnce Backup section of the Hewlett Packard
Enterprise Information Library.
Procedure
1. Navigate to http://www.hpe.com/info/storeonce/
docs.
2. In Models / Subcategories, select your product.
3. To filter the entries, select the types of documents
and your language.
Page 3