HighLine CCU3 Instruction Manual

INSTALLATION & USER MANUAL
CCU3
CENTRAL
CONTROL UNIT

CONNECTIONS
CCU3 - USER MANUAL 2
PLEASE NOTE
- The installation of all electrical items must be undertaken by a qualified professional.
- Do not use cable thicker than 1.5mm and multi-strand if possible for flexibility.
- Wire all other inputs before connecting mains power.
- To ensure perfect sealing of the control
- The RS1 rain sensor is supplied complete with 5 metres of cable. If this is not
sufficient the cable can be extended to a maximum of 50 metres using 3 x 0.5mm
cable.
unit you must pass the cables through the
grommets and insert the rubber cord for tighter seal.
1 2 3 4 5 6
LIVE 2 (CLOSE)
LIVE 1 (OPEN)
LIVE
NEUTRAL NEUTRAL
7 8 9
LIVE 1 (OPEN)
LIVE 2 (CLOSE)
COM
10 11 12 13 14
WHITE
BLUE
ACTUATOR
ROCKER SWITCH
MAINS POWER RAIN SENSOR
YELLOW
FUSE
(2.5A)
POWER
SIGNAL
ANTENA
LEARN
}
} } }

PROGRAMMING REMOTES
CCU3 - USER MANUAL 3
1
Press the ‘Learn’ button on the CCU3 the red LED will flash and the
buzzer sounds.
*Only if using 5-Channel Remote*
Select the channel you wish to programme using the ‘3’ and ‘4’ select
buttons on the remote control.
2
Now press and hold the ‘2’ button on the remote control for roughly
4 seconds or until the buzzer stops.
3
Now press the ‘2’ button again on the remote control two more times
whilst the buzzer bleeps.
4
CCU3RC1 (1-Channel Remote) *
CCU3RC5
*Please Note - The CCU3RC1 is identical in appearance to the CCU3RC5 however
the select buttons (3 and 4) and LED’s are disabled.
(5-Channel Remote)
5The red LED will flash three times and the buzzer will sound. The
remote control has now been programmed.
To delete the remote controls stored on the CCU3 control unit’s
memory simply press and hold the ‘Learn’ button for 10-15 seconds
until the red LED flashes.

TECHNICAL DATA
FUNCTIONS
CCU3 - USER MANUAL 4
EDOC
)TUPNI(EGATLOV
)TUPTUO(EGATLOV
TNERRUCTUPTUO
SSALCNOITCETORP
mm54x931x261
OPERATING TEMP.
SNOISNEMID
STUPNI
CAV032
CAV032
A7
-10° / +60°C
CCU3
45PI
RS1, CCU3RC1, CCU3RC5, S50-1, RRTKEY
Open - Press the Open button and the actuator will fully open.
ROCKER SWITCH
Stop - If the actuator is opening press the Close buttton to stop the actuator
in mid-position. Or if the actuator is closing press the Open button to stop the
actuator.
Close - Press the Close button and the actuator will fully close.
Open - Press the Open button (1) on the remote and the actuator will fully open.
REMOTE CONTROL
Stop - If the actuator is opening press the Close button to stop the actuator
in mid-position. Or if the actuator is closing press the Open button to stop the
actuator.
Close - Press the Close button (2) on the remote adn the actuator will fully close.
*For multi-channel remotes first select the correct channel you wish to operate
using the select buttons (3 and 4).
Close - When Rain is detected the Rain Sensor will perform a full close cycle
until rain is no longer present. The Rain Sensor takes 1st priority so all other
inputs will be disabled while rain is still present. Once rain is no longer present
it will take up to 8 minutes before other inputs can be used.
RAIN SENSOR