HIK VISION DS-1H34 Series User manual

PoE Video Repeater
User Manual
User Manual
COPYRIGHT © 2018 Hangzhou Hikvision Digital
Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others,
wordings, pictures, graphs are the properties of
Hangzhou Hikvision Digital Technology Co., Ltd. or its
subsidiaries (hereinafter referred to be “Hikvision”).
This user manual (hereinafter referred to be “the
Manual”) cannot be reproduced, changed, translated,
or distributed, partially or wholly, by any means,
without the prior written permission of Hikvision.
Unless otherwise stipulated, Hikvision does not make
any warranties, guarantees or representations, express
or implied, regarding to the Manual.
About This Manual
This Manual is applicable to DS-1H34 Series PoE Video
Repeater.
The Manual includes instructions for using and
managing the product. Pictures, charts, images and all
other information hereinafter are for description and
explanation only. The information contained in the
Manual is subject to change, without notice, due to
firmware updates or other reasons. Please find the
latest version in the company website
(http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of
professionals.

Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are
the properties of Hikvision in various jurisdictions.
Other trademarks and logos mentioned below are the
properties of their respective owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE
LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE,
SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH
ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION, MERCHANTABILITY,
SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR
PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS,
EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY
SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES
FOR LOSS OF BUSINESS PROFITS, BUSINESS
INTERRUPTION, OR LOSS OF DATA OR
DOCUMENTATION, IN CONNECTION WITH THE USE OF
THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS,
THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR
OWN RISKS. HIKVISION SHALL NOT TAKE ANY
RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY
LEAKAGE OR OTHER DAMAGES RESULTING FROM
CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR
OTHER INTERNET SECURITY RISKS; HOWEVER,
HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT
IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE
CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION
BEFORE USING THIS PRODUCT IN ORDER TO ENSURE
THAT YOUR USE CONFORMS THE APPLICABLE LAW.
HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT
THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS
MANUAL AND THE APPLICABLE LAW, THE LATER
PREVAILS.

Regulatory Information
FCC Information
Please take attention that changes or modification not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
FCC compliance: This equipment has been tested and
found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
EU Conformity Statement
This product and - if applicable - the
supplied accessories too are marked with
"CE" and comply therefore with the
applicable harmonized European
standards listed under the EMC Directive 2014/30/EU,
the LVD Directive 2014/35/EU, the RoHS Directive
2011/65/EU.
2012/19/EU (WEEE directive): Products
marked with this symbol cannot be
disposed of as unsorted municipal waste in
the European Union. For proper recycling,
return this product to your local supplier
upon the purchase of equivalent new
equipment, or dispose of it at designated collection
points. For more information see: www.recyclethis.info
2006/66/EC (battery directive): This
product contains a battery that cannot be
disposed of as unsorted municipal waste in
the European Union. See the product
documentation for specific battery
information. The battery is marked with
this symbol, which may include lettering to indicate
cadmium (Cd), lead (Pb), or mercury (Hg). For proper
recycling, return the battery to your supplier or to a
designated collection point. For more information see:
www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A)
standards requirements.

Safety Instruction
These instructions are intended to ensure that user can
use the product correctly to avoid danger or property
loss.
The precaution measure is divided into “Warnings” and
“Cautions”
Warnings: Serious injury or death may occur if any of
the warnings are neglected.
Cautions: Injury or equipment damage may occur if any
of the cautions are neglected.
Warnings
Proper configuration of all passwords and other
security settings is the responsibility of the installer
and/or end-user.
In the use of the product, you must be in strict
compliance with the electrical safety regulations of
the nation and region. Please refer to technical
specifications for detailed information.
Input voltage should meet both the SELV (Safety Extra
Low Voltage) and the Limited Power Source with 100
to 240 VAC or 12 VDC according to the IEC60950-1
standard. Please refer to technical specifications for
detailed information.
Do not connect several devices to one power adapter
as adapter overload may cause over-heating or a fire
hazard.
Please make sure that the plug is firmly connected to
the power socket.
If smoke, odor or noise rise from the device, turn off
the power at once and unplug the power cable, and
then please contact the service center.
Warnings Follow these
safeguards to prevent
serious injury or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.

Preventive and Cautionary Tips
Before connecting and operating your device, please be
advised of the following tips:
Ensure unit is installed in a well-ventilated, dust-free
environment.
Unit is designed for indoor use only.
Keep all liquids away from the device.
Ensure environmental conditions meet factory
specifications.
Ensure unit is properly secured to a rack or shelf.
Major shocks or jolts to the unit as a result of
dropping it may cause damage to the sensitive
electronics within the unit.
Use the device in conjunction with an UPS if possible.
Power down the unit before connecting and
disconnecting accessories and peripherals.
Improper use or replacement of the battery may
result in hazard of explosion. Replace with the same
or equivalent type only. Dispose of used batteries
according to the instructions provided by the battery
manufacturer.
The installation surface should bear the force which is
3 times of the device gravity and not less than 50 N.
If the device is wall-mounted, adopt the expansion
screws of M3X10 or above.
Applicable Models
This manual is applicable to the models listed in the
following table.
Series
Model
DS-1H34 Series PoE
Video Repeater
DS-1H34-0101P
DS-1H34-0102P
Symbol Conventions
The symbols that may be found in this document are
defined as follows.
Symbol
Description
Indicates a potentially hazardous situation,
which if not avoided, could result in
equipment damage, data loss, performance
degradation, or unexpected results.
Provides additional information to emphasize
or supplement important points of the main
text.

1Introduction
1.1 Overview
The DS-1H34 Series PoE Video Repeater is used for the
network connection of the devices in the security
surveillance project. The video repeater can be
cooperated with the IP camera and access layer PoE
switch to extend the transmission distance of network
and PoE signal and transmit the signal of the front-end
network device to the center when the network cable is
longer than 100 meters.
1.2 Features
Support 1-ch input and 1-ch output, and 1-ch input
and 2-ch output PoE relay function.
Support EXTEND mode of PSE (Power Sourcing
Equipment) output interface. The transmission
distance of single-stage network can be extended to
250 meters when the EXTEND mode is enabled.
Standard Cat. 5e twisted pair. For 100 Mbps mode,
the repeater supports 4-stage cascade and the max.
transmission distance reaches 400 meters (terminal
power consumption < 5W). For EXTEND mode, the
max. transmission distance reaches 500 meters
(terminal power consumption < 5W).
IEEE802.3at and IEEE802.3af are supported for PoE
output.
10/100BaseT(X) (RJ45 interface).
IEEE802.3, IEEE802.3u and IEEE802.3x network
standards available.
Store-and-forward switching method.
The time delay of data exchange is shorter than 5
microseconds.
The working temperature range for wide temperature
range models is within -30˚C to 70˚C.
Solid metal case of high strength.
1.3 Typical Application
1.3.1 1-ch Input and 2-ch Output Mode
Refer to Figure 1-1 for the 1-ch input and 2-ch output
mode.
Figure 1-1 1-ch Input and 2-ch Output Mode
DS-1H34-0102P does not support cascade.

1.3.2 100 Mbps Mode Cascade (with EXTEND Mode Off)
Refer to Figure 1-2 for the 100 Mbps mode cascade.
Figure 1-2 100 Mbps Mode Cascade
The power of the IP camera should be lower than
5W.
1.3.3 10 Mbps Mode (with EXTEND Mode On)
Refer to Figure 1-3 for the 100 Mbps mode.
Figure 1-3 10 Mbps Mode
The power of the IP camera should be lower than 5W.
The network interface of PoE switch should be
configured to be 10 Mbps.
The EXTEND mode does not support cascade.
2Panels
2.1 Input Panel
Refer to Figure 2-1 for the input panel (PoE IN) of
DS-1H34-0101P and DS-1H34-0102P.
Figure 2-1 Input Panel
Refer to Table 2-1 for the description of input panel
(PoE IN) of DS-1H34-0101P and DS-1H34-0102P.

Table 2-1 Description of Input Panel
Serial
No.
Item
Description
1
PD
Indicator
Lights in green when PSE is
connected.
2
RJ45
Interface
Input network interface:
10/100BaseT(X) and IEEE 802.3at
standard of PD (Power Device)
connection.
The indicator lights in yellow
when there is no data
transmission and flashes in yellow
when there is data transmission
when PSE is connected.
3
DIP
Switch
ON: 10 Mbps mode of PSE
network interface is enabled and
the network transmission distance
can reach 200 meters.
OFF (default): Normal 100 Mbps
mode of PSE network interface is
enabled and the network
transmission distance is 100
meters.
4
GND
Ground terminal.
2.2 Output Panel
Refer to Figure 2-2 for the input panel (PoE IN) of
DS-1H34-0101P and DS-1H34-0102P.
Figure 2-2 Output Panel of DS-1H34-0101P
Refer to Table 2-2 for the description of output panel
(PoE OUT) of DS-1H34-0101P.
Table 2-2 Description of Output Panel for DS-1H34-0101P
Serial
No.
Item
Description
1
Indicators
REPEAT Indicator: Lights in red
when the output power exceeds
the limit.
PSE Indicator: Lights in green
when PD is connected and the
power supply is normal.
2
RJ45
Interface
Output network interface:
10/100BaseT(X) and IEEE
802.3af/at standard of PSE output.
Refer to Figure 2-3 for the output panel (PoE OUT) of
DS-1H34-0102P.

Figure 2-3 Output Panel of DS-1H34-0102P
Refer to Table 2-3 for the description of output panel
(PoE OUT) of DS-1H34-0102P.
Table 2-3 Description of Output Panel for DS-1H34-0102P
Serial
No.
Item
Description
1
Indicator
REPEAT Indicator: Lights in red
when the output power exceeds
the limit.
PSE1 Indicator: Lights in green
when PD is connected to the PSE1
and the power supply is normal.
PSE2 Indicator: Lights in green
when PD is connected to the PSE2
and the power supply is normal.
2
RJ45
Interface
Output network interface 1:
10/100BaseT(X) and IEEE 802.3af
standard of PSE output.
3
RJ45
Interface
Output network interface 2:
10/100BaseT(X) and IEEE 802.3af
standard of PSE output.
3Dimension
Refer to Figure 3-1 for the dimension of DS-1H34 series
PoE video repeater.
Figure 3-1 Dimension

4Appendix
4.1 Specifications
Model
DS-1H34-0101P
DS-1H34-0102P
Input
1-ch 10/100BaseT(X) and IEEE 802.3at
standard of PD connection.
Output
1-ch
10/100BaseT(X)
and IEEE 802.3af/at
standard of PSE
output.
2-ch
10/100BaseT(X)
and IEEE 802.3af
standard of PSE
outputs.
MTBF (Mean
Time
Between
Failure)
100000 hours
Consumption
< 2W
Working
Temperature
-30 ºC to +70 ºC (-22 ºF to +158 ºF)
Working
Humidity
10% to 90%
Dimensions
(W×H×D)
71.6 × 26.1 × 95.5 mm (2.8 × 1.0 × 3.8
inch)
Weight
0.3 Kg (0.7 lb)
ESD
(Electro-Static
Discharge)
Contact discharge: ±7 KV
Air discharge: ±9 KV
Surge
Power port: Line-to-ground: ±2 KV;
Line-to-line: 1 KV
Network port: Line-to-ground: ±4 KV
EFT (Electrical
Fast Transient
Burst)
Network port: ±2 KV
4.2 Glossary
Glossary
Description
PSE (Power
Sourcing
Equipment)
The power sourcing equipment in PoE
system.
PD (Power
Device)
The power receiving equipment in PoE
system.
IEEE
802.3af
PoE standard. The PSE can supply power
to the PD lower than 13W via Ethernet
transmission cable.
IEEE
802.3at
PoE standard. The PSE can supply power
to the PD lower than 30W via Ethernet
transmission cable.
0100001080117
UD01361B-B