HIK VISION Day/ Night Color Camera User manual
Day/ Night Color Camera
User Manual
V 2.1.0
Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer.
This manual is applicable to DS-2CC5102P(N)、DS-2CC5112P(N)、DS-2CC5172P(N)、DS-2CC5182P(N)、
DS-2CC5192P(N) Day / Night Color Camera.
This manual may contain several technically incorrect places or printing errors, and the content is subject to
change without notice. The updates will be added into the new version of this manual. We will readily improve or
update the products or procedures described in the manual.
Safety Instructions
These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may cause if any of the warnings is neglected.
Cautions: Injury or equipment damage may cause if any of the cautions is neglected.
Warnings Follow these safeguards
to prevent serious injury or
death.
Cautions Follow these precautions
to prevent potential injury or
material damage.
Warnings
1. In the use of the product, you must be strict compliance with the electrical safety regulations of the nation and
region.
2. Input voltage should meet both the SELV(Safety Extra Low Voltage) and the Limited Power Source with DC
12V according to the IEC60950－1 standard. Please refer to technical specifications for detail information.
3. Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard.
4. Please make sure that the plug is firmly connected on the power socket.
5. When the product is mounted on wall or ceiling, the device shall be firmly fixed.
6. If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then
please contact the service center.
7. If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (We shall not assume any responsibility for problems caused by
unauthorized repair or maintenance.)
Cautions：
1. Make sure the power supply voltage is correct before using the camera.
2. Do not drop the camera or subject it to physical shock.
3. Do not touch CCD (Charge Coupled Device) modules with fingers. If cleaning is necessary, use clean cloth
with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, please turn on
the lens cap to protect the CCD from dirt.
4. Do not aim the camera at the sun or extra bright places. A blooming or smear may occur otherwise (which is
not a malfunction however), and affecting the endurance of CCD at the same time.
5. The CCD may be burned out by a laser beam, so when any laser equipment is on using, make sure that the
surface of CCD will not be exposed to the laser beam.
6. Do not place the camera in extremely hot, cold(the operating temperature shall be－10℃～＋60℃), dusty
or damp locations, and do not expose it to high electromagnetism radiation.
7. To avoid heat accumulation, good ventilation is required for operating environment.
8. Keep the camera away from liquid while on using.
9. While on a delivery, the camera shall be packed in its original packing, or packing of the same texture.
10. Regular part replacement: a few parts (e.g. electrolytic capacitor) of the equipment shall be replaced
regularly according to their average enduring time. The average time varies because of differences between
operating environment and using history, so regular checking is recommended for all the users. Please
contact with your dealer for more details.
TableofContents
CHAPTER1INTRODUCTION .............................................................................................................0
1.1FEATURES...........................................................................................................................................0
1.2FUNCTIONS ........................................................................................................................................0
1.3DESCRIPTIONOFDOMECAMERA............................................................................................................1
CHAPTER2INSTALLATION................................................................................................................2
2.1DOMECAMERAMOUNTING ..................................................................................................................2
2.2DOMEELECTRICALBOXADAPTERINSTALLATION ........................................................................................4
APPENDIX .......................................................................................................................................6
DS‐2CC5102P(N) ...................................................................................................................................6
Specifications....................................................................................................................................6
Dimensions .......................................................................................................................................7
DS‐2CC5112P(N)................................................................................................................................... 8
Specification .....................................................................................................................................8
Dimensions .......................................................................................................................................9
DS‐2CC5172P(N) .................................................................................................................................10
Specifications..................................................................................................................................10
Dimensions .....................................................................................................................................11
DS‐2CC5182P(N) .................................................................................................................................12
Specifications..................................................................................................................................12
Dimensions .....................................................................................................................................13
DS‐2CC5192P(N) .................................................................................................................................14
Specifications..................................................................................................................................14
Dimensions .....................................................................................................................................15
Chapter 1 Introduction
1.1 Features
This series of the camera adopt high performance sensor and advanced print circuit board design technology with
high resolution, low distortion and low noise, etc. The key features as following:
• High performance image sensor CCD, high resolution, capable of providing clear images.
• Low illumination, color/B&W auto switch.
•Backlight compensation
•Auto white balance
• Auto electronic shutter control, adaptive to different environments.
• Auto gain control, with brightness adaptive.
•3 Axis adjustment.
• Advanced technique design, with high reliability.
1.2 Functions
ICR Switch: The camera provides two operation modes: color, and B&W. You can increase sensitivity in low light
conditions by switching to B&W mode (removing the IR cut filter). Color mode is preferred in normal lighting
conditions.
AGC: AGC allows users to adjust the gain of amplifier, enabling the camera to output the standard video signal in
different lighting conditions. As scene lighting decreases, the system will automatically adjust, adding a mixture of
AGC and slow shutter according to the AGC limit setting. In low illumination, AGC will increase camera’s
sensitivity, and output bright and clear video.
S/N ratio: It refers to the ratio between signal voltage and noise voltage. While the ratio is larger, the effect of
noise is less, and the image is more spotless.
White Balance: This feature automatically processes the viewed image to retain color balance over a color
temperature range.
.
User Manual of Color Camera V2.1.0
1.3 Description of Dome Camera
Figure 1.4
1
User Manual of Color Camera V2.1.0
Chapter 2 Installation
Prior to mounting, please make sure that the device in the package is in good condition and all the assembly parts
are complete.
2.1 Dome Camera Mounting
The following section has described the DS-2CC5102P(N) 、DS-2CC5112P(N) 、DS-2CC5172P(N) 、
DS-2CC5182P(N)、DS-2CC5192P(N) series dome camera installation as the example.
Note: the mounting wall must be with certain thickness and capable of supporting three times the weight of
dome camera.
1. Use your hands to hold the back box of dome camera and then rotate the bubble in anti-clockwise
direction to remove it.
Figure 2.1.1 Remove the Bubble
2. By referring to the Figure 2.1.2, use the self-tapping screws to secure the back box of dome camera to
the wall.
Note: the expansion screws are required for the cement wall mounting application.
2
User Manual of Color Camera V2.1.0
Figure 2.1.2 Secure Back Box to the Wall
3. Adjust the lens to the desired monitoring location and obtain the clear images. This series dome camera
has the pan movement range of 0~355°, the tilt movement range of 0~80°and the rotate movement
range of 0~355° .
Figure 2.1.3 Adjust Lens Orientation
4. Rotate the bubble in clockwise direction to replace it to the dome camera.
3
User Manual of Color Camera V2.1.0
Figure 2.1.4 Replace the Bubble
Figure 2.1.5 accomplished
2.2 Dome Electrical Box Adapter Installation
The following section has described the DS-2CC5102P(N) 、DS-2CC5112P(N) 、DS-2CC5172P(N) 、
DS-2CC5182P(N)、DS-2CC5192P(N) series dome camera installation as the example.
1. Attach DS-1244ZJ to Electrical Box Adapter as shown in Figure 2.2.1
4
User Manual of Color Camera V2.1.0
Figure 2.2.1
2. Attach Dome to DS-1244ZJ as shown in Figure 2.2.2,Please reference Dome Camera Mounting if
needed.
Figure 2.2.2
5
User Manual of Color Camera V2.1.0
Appendix
DS-2CC5102P(N)
Specifications
DS‐2CC5102P(N)Model
Parameter420TVLCCDDomeCamera
Camera
ImageSensor1/3”SONYSuperHADCCDII
SignalSystemPAL/NTSC
EffectivePixelsPAL:500(H)×582(V)
NTSC:510(H)×492(V)
Min.Illumination0.1Lux@(F1.2,AGCON)
0.28Lux@(F2.0,AGCON)
ShutterTimePAL:1/50sto1/100,000s
NTSC:1/60sto1/100,000s
3.6mm@F2.0(2.8mm,6mm,8mm,12mm,16mm
optional)
Lens
Angleofview:78°(3.6mm)
LensMountM12
AngleAdjustmentPan:0‐355°,Tilt:0‐90°,Rotation:0‐355°
Day&NightElectronic
HorizontalResolution420TVL
SynchronizationInternalsynchronization
VideoOutput
1Vp‐pcompositeoutput(75Ω/BNC);
Testmonitorout[1Vp‐pcompositeoutput(75Ω/BNC),
deviceline]
S/NRatioMorethan50dB
General
OperatingConditions‐10°C‐60°C(14°F‐140°F)
Humidity90%orless(non‐condensing)
PowerSupply12VDC±10%
PowerConsumptionMax.2W
DimensionΦ97.8x64.4mm(φ3.85”x2.54”)
Weight300g(0.66lbs)
6
User Manual of Color Camera V2.1.0
Dimensions
Unit:mm
7
User Manual of Color Camera V2.1.0
DS-2CC5112P(N)
Specification
DS‐2CC5112P(N)Model
Parameter 480TVLCCDDomeCamera
Camera
ImageSensor 1/3”SONYSuperHADCCDII
SignalSystemPAL/NTSC
EffectivePixelsPAL:752(H)×582(V)
NTSC:768(H)×494(V)
Min.Illumination0.1Lux@(F1.2,AGCON)
0.28Lux@(F2.0,AGCON)
ShutterTimePAL:1/50sto1/100,000s
NTSC:1/60sto1/100,000s
3.6mm@F2.0(2.8mm,6mm,8mm,12mm,16mm
optional)
Lens
Angleofview:78°(3.6mm)
LensMountM12
AngleAdjustmentPan:0‐355°,Tilt:0‐90°,Rotation:0‐355°
Day&NightElectronic
HorizontalResolution480TVL
Synchronization Internalsynchronization
VideoOutput
1Vp‐pcompositeoutput(75Ω/BNC);
Testmonitorout[1Vp‐pcompositeoutput(75Ω/BNC),
deviceline]
S/NRatioMorethan52dB
General
OperatingConditions‐10°C‐60°C(14°F‐140°F)
Humidity90%orless(non‐condensing)
PowerSupply12VDC±10%
PowerConsumptionMax.2W
Dimension Φ97.8x64.4mm(φ3.85”x2.54”)
Weight300g(0.66lbs)
8
User Manual of Color Camera V2.1.0
Dimensions
Unit:mm
9
User Manual of Color Camera V2.1.0
DS-2CC5172P(N)
Specifications
DS‐2CC5172P(N)Model
Parameter 540TVLCCDDomeCamera
Camera
ImageSensor 1/3”SONYSuperHADCCDII
SignalSystemPAL/NTSC
EffectivePixelsPAL:752(H)×582(V)
NTSC:768(H)×494(V)
Min.Illumination0.1Lux@(F1.2,AGCON)
0.28Lux@(F2.0,AGCON)
ShutterTimePAL:1/50sto1/100,000s
NTSC:1/60sto1/100,000s
3.6mm@F2.0(2.8mm,6mm,8mm,12mm,16mm
optional)
Lens
Angleofview:78°(3.6mm)
LensMountM12
AngleAdjustmentPan:0‐355°,Tilt:0‐90°,Rotation:0‐355°
Day&NightElectronic
HorizontalResolution540TVL
Synchronization Internalsynchronization
VideoOutput
1Vp‐pcompositeoutput(75Ω/BNC);
Testmonitorout[1Vp‐pcompositeoutput(75Ω/BNC),
deviceline]
S/NRatioMorethan52dB
General
OperatingConditions‐10°C‐60°C(14°F‐140°F)
Humidity90%orless(non‐condensing)
PowerSupply12VDC±10%
PowerConsumptionMax.2W
Dimension Φ97.8x64.4mm(φ3.85”x2.54”)
Weight300g(0.66lbs)
10
User Manual of Color Camera V2.1.0
Dimensions
Unit:mm
11
User Manual of Color Camera V2.1.0
DS-2CC5182P(N)
Specifications
DS‐2CC5182P(N)Model
Parameter 600TVLCCDDomeCamera
Camera
ImageSensor 1/3”SONYSuperHADCCDII
SignalSystemPAL/NTSC
EffectivePixelsPAL:752(H)×582(V)
NTSC:768(H)×494(V)
Min.Illumination0.1Lux@(F1.2,AGCON)
0.28Lux@(F2.0,AGCON)
ShutterTimePAL:1/50sto1/100,000s
NTSC:1/60sto1/100,000s
3.6mm@F2.0(2.8mm,6mm,8mm,12mm,16mm
optional)
Lens
Angleofview:78°(3.6mm)
LensMountM12
AngleAdjustmentPan:0‐355°,Tilt:0‐90°,Rotation:0‐355°
Day&NightElectronic
HorizontalResolution600TVL
Synchronization Internalsynchronization
VideoOutput
1Vp‐pcompositeoutput(75Ω/BNC);
Testmonitorout[1Vp‐pcompositeoutput(75Ω/BNC),
deviceline]
S/NRatioMorethan52dB
General
OperatingConditions‐10°C‐60°C(14°F‐140°F)
Humidity90%orless(non‐condensing)
PowerSupply12VDC±10%
PowerConsumptionMax.2W
Dimension Φ97.8x64.4mm(φ3.85”x2.54”)
Weight300g(0.66lbs)
12
User Manual of Color Camera V2.1.0
Dimensions
Unit:mm
13
User Manual of Color Camera V2.1.0
DS-2CC5192P(N)
Specifications
DS‐2CC5192P(N)Model
Parameter 650TVLCCDDomeCamera
Camera
ImageSensor 1/3”SONYEXViewHADCCDII
SignalSystemPAL/NTSC
EffectivePixelsPAL:976(H)×582(V)
NTSC:976(H)×494(V)
Min.Illumination0.1Lux@(F1.2,AGCON)
0.28Lux@(F2.0,AGCON)
ShutterTimePAL:1/50sto1/100,000s
NTSC:1/60sto1/100,000s
3.6mm@F2.0(2.8mm,6mm,8mm,12mm,16mm
optional)
Lens
Angleofview:78°(3.6mm)
LensMountM12
AngleAdjustmentPan:0‐355°,Tilt:0‐90°,Rotation:0‐355°
Day&NightElectronic
HorizontalResolution650TVL
Synchronization Internalsynchronization
VideoOutput
1Vp‐pcompositeoutput(75Ω/BNC);
Testmonitorout[1Vp‐pcompositeoutput(75Ω/BNC),
deviceline]
S/NRatioMorethan52dB
General
OperatingConditions‐10°C‐60°C(14°F‐140°F)
Humidity90%orless(non‐condensing)
PowerSupply12VDC±10%
PowerConsumptionMax.2W
Dimension Φ97.8x64.4mm(φ3.85”x2.54”)
Weight300g(0.66lbs)
14
This manual suits for next models
10
Table of contents
Other HIK VISION Security Camera manuals
HIK VISION
HIK VISION DS-2CD5A46GO-IZS User manual
HIK VISION
HIK VISION DS-2CE56D8T-IT1 User manual
HIK VISION
HIK VISION DS-2CD7A26G0/P-IZHSWG User manual
HIK VISION
HIK VISION DS-2CE16H5T-IT User manual
HIK VISION
HIK VISION UD.6L0201B2151A02 User manual
HIK VISION
HIK VISION DS-2XS6A25G0-I/CH20S40 User manual
HIK VISION
HIK VISION DS-2DYH2A0IXS-D User manual
HIK VISION
HIK VISION E-series User manual
HIK VISION
HIK VISION UD04285B User manual
HIK VISION
HIK VISION DS-2CE16H1T-IT3Z User manual
HIK VISION
HIK VISION DS-2DF8836IX-AEL User manual
HIK VISION
HIK VISION ColorVu DS-2CE72DFT-FC User manual
HIK VISION
HIK VISION DS-2CD63C5G0-IS User manual
HIK VISION
HIK VISION iDS-2VS435-F840-EY User manual
HIK VISION
HIK VISION PIR Series User manual
HIK VISION
HIK VISION DS-2CE16H1T-IT User manual
HIK VISION
HIK VISION DS-MH2311/64G/GLE(C) User manual
HIK VISION
HIK VISION DS-2CD8253F-EI User guide
HIK VISION
HIK VISION TURBO HD H8T Series User manual
HIK VISION
HIK VISION HiLook IPC-T250H User manual
